有机垃圾厌氧消化泡沫产生机理及控制方法

为了分析厌氧消化泡沫的产生机理和控制方法有助于解决有机垃圾厌氧消化起泡问题,本文调研了近年来报道的厌氧消化系统起泡现象,并从底物特性、反应器构造及运行条件和消化过程相关特性3方面分析了不同底物、工艺和环境条件下厌氧消化反应器的起泡机理;讨论了丝状菌指数、表面张力、粘度、有机负荷、起泡趋势和泡沫稳定性等参数作为起泡风险评价指标的合理性;介绍和比较了4类消泡方法（物理法、机械法、生物法和化学法）的消泡原理及优缺点.目前,除污泥厌氧消化系统外,其他有机垃圾厌氧消化系统起泡的主要因素尚不明确,而这也限制了泡沫控制方法的开发.后期探索关键起泡微生物或研究生物表面活性物质与起泡的相关性,将有助于从新的角度揭示起泡机理,并开发出针对性更强的泡沫控制方法.     

Ni2+对好氧颗粒污泥系统性能的影响

以城镇污水处理厂A²/O工艺的回流污泥作为接种污泥,在序批式反应器（SBR）中培养好氧颗粒污泥（AGS）,探究Ni²⁺对AGS系统的影响.结果表明：在25℃的条件下,50d左右培养出成熟的AGS,其形态多呈球状或椭球状,外表分布着少量丝状菌,颗粒污泥粒径主要在2~4mm,MLSS达6000mg/L,SVI维持在40~50mL/g.将Ni²⁺作用于培养出的成熟AGS,Ni²⁺在0~2mg/L的浓度范围内会提高AGS的稳定性,使MLSS上升,SVI降低;同时会促进AGS分泌胞外多聚物（EPS）,EPS组成成分中的蛋白质（PN）明显多于多糖（PS）;Ni²⁺对好氧颗粒污泥去除总氮（TN）的抑制程度要大于COD,最终COD去除率可维持在95%以上,TN去除率可维持在70%以上.     

Removal of heavy metals (Cr6+,Ni2+)from polluted water using decaying leaves of plane (Plantanus orientalis)

plane decaying leaves have been found capable of removing chromium and nickel ions from aqueous solutions. The removal efficiency depends upon the pH conditions, ions components and concentrations, and concentrations of leaves in media. The maximum removal for unique Cr⁶⁺ is about 7.5-8.0g/kg leaves at pH 4. 0, for unique Ni²⁺ about 2. 6g/kg at the region of PH5. 0-5.5. Under the described conditions nickel increases chromium uptake by plane decaying leaves from solution.     

大气降尘对土壤重金属累积量估算方法探讨——以重庆市綦江县永新冶炼厂为例

中国的有色金属冶炼企业、矿区周围土壤重金属污染日趋严重.本文对可能造成土壤污染的途径进行了简要分析,并以重庆市綦江县永新冶炼厂为例,分析了冶炼厂排放废气中含重金属颗粒物沉降进入土壤的途径,结合厂址周围土壤中镍含量的监测数据,计算分析了冶炼厂投产30年后,受影响区域因大气降尘引起的土壤镍污染分布状况及趋势,估算得出每年大约有250 kg的镍沉降到厂址周围约4 km2范围内的土壤中,自然沉降率约为32%,为区域土壤重金属污染防治提供了科学依据.     

Prediction of future disposal of end-of-life refrigerators containing CFC-11

The objective of this study was to predict the number of refrigerators containing CFC-11 blown isolation foam and the amount of CFC-11 banked in these refrigerators. By using a Weibull-based survival function, the number of CFC-11 containing and still-functioning refrigerators was estimated to be approximately 1.6 million in 2013 in Turkey. In order to determine the amount of CFC-11 in the isolation foam of these refrigerators, polyurethane (PU) foam samples were taken from a refrigerator manufactured in 1993 and the quantity of CFC-11 was analyzed by a GC-MS. It was determined that 113–195 mg CFC-11/g PU remains in the PU foam depending on the location such as door, sides, top and bottom. Knowing that a mid-sized refrigerator contains 4 kg PU on average, the total amount of PU foam to be disposed of is 6344 tons when the CFC-11 containing refrigerators in Turkey become obsolete in the near future. Furthermore, 717–1237 tons of CFC-11 are expected to be banked in the PU foam of these refrigerators which will exert an equivalent amount of ozone depleting potential (ODP). In addition, the global warming potential will vary between 3.4 and 5.9 million tons of CO₂.     

Development of heat transfer and evaporation model of LNG covered by Hi-Ex foam

Natural gas is a kind of clean, efficient green energy source, which is used widely. Liquefied natural gas (LNG) is produced by cooling natural gas to −161 °C, at which it becomes the liquid. Once LNG was released, fire or explosion would happen when ignition source existed nearby. The high expansion foam (Hi-Ex foam) is believed to quickly blanket on the top of LNG spillage pool and warm the LNG vapor to lower the vapor cloud density at the ground level and raising vapor buoyancy. To identify the physical structure after it contacted with LN₂ and to develop heat transfer model, the small-scale field test with liquid nitrogen (LN₂) was designed. In experiment, three layers including frozen ice layer, frozen Hi-Ex layer and soft layer of Hi-Ex foam were observed at the steady state. By characterizing physical structure of the foam, formulas for calculating the surface of single foam bubble and counting foam film thickness were deduced. The micro heat transfer and evaporation model between cryogenic liquid and Hi-Ex foam was established. Indicating the physical structure of the frozen ice layer, there were a certain number of icicles below it. The heat transfer and evaporation mathematical model between the frozen ice layer and LNG was derived. Combining models above with the heat transfer between LNG, ground and cofferdam, the heat transfer and evaporation mathematical model of LNG covered by Hi-Ex foam was developed eventually. Finally, LN₂ evaporation rate calculated by this model was compared with the measured evaporation rate. The calculated results are 1.2–2.1 times of experimental results, which were acceptable in engineering and proved the model was reliable.     

Ti/SnO_2-Sb阳极-空气阴极电催化降解染料废水

为解决电化学法处理高盐染料废水存在的能耗大、成本高等问题,分别采用溶胶-凝胶法和辊压法制备Ti/SnO_2-Sb阳极和空气阴极,构建了Ti/SnO_2-Sb阳极-空气阴极双极体系(TSSA-ADC)。甲基橙(MO)作为高盐染料废水的典型污染物,考察了电流强度、MO浓度、电解液浓度和初始p H对TSSA-ADC体系和TSSA单阳极体系降解MO的影响。结果表明:与TSSA单阳极体系相比,TSSA-ADC体系具有更好的抗有机负荷冲击、抗盐分冲击、抗酸碱波动能力,能够维护酸碱平衡防止硬度离子结垢。最佳反应条件为电流强度为0.030 A,电解液浓度为3%,MO浓度为100 mg/L,初始pH=6。以MO去除率达到98%为基准,TSSA-ADC体系比TSSA体系可节能74.26%。     

镍掺杂二氧化钛光催化剂的制备与光催化性能研究

利用溶胶-凝胶法制备了镍掺杂的二氧化钛,采用紫外可见分光光度计、傅里叶红外分光光度计、X衍射仪(XRD)、扫描电镜(SEM)等测试手段对结果进行了表征。表征结果表明在550℃下煅烧的产物主要是锐钛型二氧化钛,镍的掺杂使得二氧化钛的紫外可见反射光谱明显红移,且镍掺杂二氧化钛的粒度减小,团聚程度下降。以活性艳蓝KN-R为模型降解目标物,通过比较镍掺杂二氧化钛、纯二氧化钛以及标准P25二氧化钛的光催化性能发现镍掺杂二氧化钛的光催化活性最好。当钛酸正丁酯/乙醇比为1:25;钛酸正丁酯/冰乙酸比为1:1;钛酸正丁酯/硝酸镍比为1 000:3;煅烧温度为550℃,煅烧时间为2 h时,镍掺杂二氧化钛的光催化效率最高,达到73.3%。     

络合-超滤耦合工艺去除水中镍离子的研究

以聚丙烯酸钠(PAANa)和聚乙烯亚胺(PEI)作为络合剂,将其与镍离子络合后的溶液转移至超滤杯中,在0.1 MPa压力下通过聚醚砜超滤膜进行分离,研究pH值和络合剂/Ni2+装载质量比(L)对Ni2+去除率的影响,并根据朗缪尔等温模型拟合络合反应平衡常数.同时研究超滤时间对膜通量和Ni2+去除率的影响.结果表明,选用PAANa为络合剂,在pH值为8、L=5时,Ni2+的去除率达到最大值99.5%.PEI为络合剂时,Ni2+去除率在pH值为7、L为5时达到最大值93.0%.不同pH值条件下拟合得到的络合平衡常数表明,pH为7时最有利于络合反应.另外,单个络合剂单体所能结合的Ni2+个数随着pH值的升高而增大.研究结果还表明,在长达12 h的超滤时间内,PAANa为络合剂时,膜通量的衰减<10%;PEI为络合剂时,膜通量基本保持不变;Ni2+的去除率都基本保持恒定.因此,在合适条件下,络合-超滤耦合工艺能有效去除水中的镍离子.     

重质油储罐固定式泡沫灭火系统设计优化研究

通过重质油储罐的实体火灭火试验,获得了氟蛋白泡沫液和水成膜泡沫液的供给强度与灭火时间对应关系数据,确定了每种泡沫液扑救重质油储罐火灾的最低泡沫供给强度;以10 000 m3固定顶重质油储罐为例进行了泡沫系统设计计算,将优化设计方案与原有设计方案进行了对比,主要变化是泡沫发生器数量从4只提高至6~8只,泡沫主管线管径从DN200提高至DN250,泡沫消防泵流量也相应提高。优化后的储罐泡沫灭火系统提高了泡沫灭火能力,提升了系统的可靠性,降低了储罐火灾风险。