Effects of cyclodextrins on hydrolysis of malathion

Cyclodextrins （CDs）, with hydrophobic interior cavity and hydrophilic external surface, are capable of accelerating or inhibiting chemical degradation of organophosphorus pesticides through forming inclusion complexes between CDs and pesticides. This work evaluated the effects of CDs on hydrolysis of malathion in an attempt to assess their potential application in environmental approach. β-CD and its two derivatives, randomly methylated β-CD （RAMEB） and hydroxypropyl β-CD （HP-β-CD）, were tested. It was found that RAMEB could inhibit the hydrolysis of malathion, and this was the function of pH and temperature, the inhibitory effects increase with increasing concentration of RAMEB and elevating temperature between 15 and 35℃. On the other hand, β-CD and HP-β-CD have little or no stabilizing effects on malathion at all pH and temperature studied, except that the large concentration of β-CD and HP- β-CD can mildly reduce hydrolysis of malathion. Both 2 mol/L and 5 mol/L urea increase the inhibitory effects of RAMEB on hydrolysis of malathion at 25℃, oH 9.0.     

尿素/KMnO4湿法烟气脱硫脱氮的试验研究

采用尿素和KMnO₄配制成的吸收液,在填有金属鲍尔环的柱式喷淋吸收反应器中,对模拟烟气进行湿法烟气同时脱硫脱氮研究.结果表明:采用尿素和KMn0₄配制成的吸收液可以高效地脱除模拟烟气中的SO₂和NO_x,脱硫脱氮率平均分别达到99.6%和62.5%;反应吸收液中主要含有因吸收NOx和SO₂而生成的NO₃-,NO₂-,NH₄+和SO₄2-等离子;NO₃-,NO₂-和NH₄+的生成曲线及尿素的消耗曲线均为线性,其速率常数分别为0.009 1,0.0074,0.091 6和0.950 8 mmol/(L·min).吸收反应为零级反应.      

碳氮共掺杂污泥基吸附剂去除水中Cr(Ⅵ)

以城市污水厂脱水污泥为原料,通过添加尿素等辅助材料碳化制备污泥基吸附剂。采用比表面积孔隙分布测定仪、扫描电镜（SEM）、X射线衍射仪（XRD）对吸附剂表面组成及其结构进行表征,对比研究了掺入添加剂前后碳化污泥吸附剂对Cr（Ⅵ）的吸附行为。结果表明,C/N共掺杂碳化污泥吸附剂对Cr（Ⅵ）的吸附性能较直接碳化污泥吸附剂明显提高,2种吸附剂的最佳吸附时间分别为2 h和4 h,pH是影响污泥基吸附剂吸附去除Cr（Ⅵ）的关键因素,其最适pH值均在1.0~2.5范围内。室温下C/N共掺杂污泥吸附剂吸附Cr（Ⅵ）符合Langmuir吸附模型,准二级动力学模型能很好地描述2种碳化污泥基吸附剂的吸附行为。热力学研究表明,C/N共掺杂污泥吸附剂对Cr（Ⅵ）的吸附是一个自发的吸热过程。     

尿素对中国近海3种典型赤潮藻生长的影响

采用实验室一次性培养的方法,研究了尿素对中国近海3种赤潮藻---球形棕囊藻(Phaeocystis globosa)、锥状斯氏藻(Scrippsiellatrochoidea)和中肋骨条藻(Skeletonema costatum)生长的影响.结果表明,这3种赤潮藻均能利用有机氮源尿素生长,且表现出明显的浓度效应:当尿素浓度介于0~8.82μmol.L-1(以N计,下同)时,3种赤潮藻的比生长速率均较低,细胞密度也较低,与对照组相比无显著差异;当尿素浓度大于8.82μmol.L-1时,这3种赤潮藻表现出明显的生长效应.然而,3种赤潮藻适宜生长的尿素浓度并不一致,当尿素浓度分别为882、8820和8820μmol.L-1时,球形棕囊藻、锥状斯氏藻和中肋骨条藻分别达到最大比生长率0.76、0.54和0.66d-1.将3种赤潮藻在不同尿素浓度下的最大比生长速率用Monod方程拟合,得出球形棕囊藻、锥状斯氏藻和中肋骨条藻在以尿素为唯一氮源条件下的最大比生长速率和半饱和常数分别为0.73、0.47、0.63d-1和12.36、21.83和20.34μmo.lL-1.由此可见,这3种藻能够利用有机氮源尿素,无疑扩展了其氮营养来源,在无机氮源缺乏时,具有竞争优势.相比较而言,球形棕囊藻对尿素的亲和力最高,在低浓度尿素条件下,球形棕囊藻具有较高的竞争力.     

尿素为还原剂燃煤烟气脱硝技术的研究与应用

尿素由于运输、储存安全性较高,作为还原剂进行脱硝备受关注。从工艺原理、系统组成和工程应用等方面,对尿素制氨选择性催化还原技术（SCR）、选择性非催化还原技术（SNCR）和尿素法三种脱硝方法进行了综述。分析了不同技术运用过程存在的问题,并提出解决措施。     

燃油锅炉烟气尿素法同时脱硫脱氮技术

针对2th燃油锅炉烟气,采用尿素添加剂湿法同时脱硫脱氮技术进行治理。通过工程应用试验,确定工程运行时液气比为3Lm3,吸收剂尿素浓度为5%,添加剂浓度随其种类不同而不同。工程环保验收各指标均优于当地标准。     

硫酸铵和尿素对废物焚烧过程中多种途径生成氯苯类的抑制作用

氯苯类(CBz)是废弃物焚烧等过程中产生二英的前驱物,也被认为是实现二英在线检测的良好指示物,同时五氯苯(PeCBz)和六氯苯(HxCBz)也是持久性有机污染物(POPs).但氯苯在废物焚烧过程中的排放和控制尚没有受到足够重视,为此开展了模拟焚烧过程中硫酸铵和尿素对3种氯苯合成途径的抑制作用研究,包括飞灰合成,1,2-二氯代苯(1,2-DiCBz)转化高氯代苯等过程.结果表明,硫酸铵和尿素对氯苯的3种合成途径均有抑制作用,如1%尿素与废物混合焚烧对四氯苯、五氯苯和六氯苯的抑制效率分别达到了66.8%、57.4%和50.4%.比较硫酸铵和尿素对3种过程的抑制作用,认为尿素对氯苯具有更稳定的抑制能力.     

添加不同 N源条件下典型除草剂对土壤呼吸和 N2O排放的影响

通过室内土壤培养实验,采用间歇密闭培养-气相色谱法研究了添加不同N源条件下我国典型旱地除草剂对农田土壤呼吸和N2O排放的影响.结果表明,在添加（NH4）2SO4氮源条件下,莠去津和百草枯对土壤呼吸和N2O排放无显著影响（P〉0.05）.草甘膦显著抑制了土壤呼吸（P〈0.05）,是对照的78.5%,N2O的排放无显著影响（P〉0.05）,仅表现为均值降低了20.1%.苯磺隆显著促进了土壤呼吸（P〈0.05）,是对照的1.1倍,对N2O排放也无显著影响（P〉0.05）.乙草胺显著促进了土壤呼吸和N2O的排放（P〈0.05）,分别是对照的1.1和1.5倍.在添加尿素的条件下,莠去津和乙草胺对土壤呼吸和N2O排放无显著影响（P〉0.05）.百草枯显著促进了N2O的排放（P〈0.05）,是对照的1.4倍,却对土壤呼吸无显著影响（P〉0.05）.草甘膦显著抑制了土壤呼吸（P〈0.05）,仅为对照的82.5%,对N2O的排放却无显著影响（P〉0.05）.苯磺隆显著促进了土壤呼吸和N2O的排放（P〈0.05）,其分别是对照的1.3和1.6倍.鉴于不同除草剂对不同微生物生理代谢影响的复杂性,其对温室气体的作用和影响还需长期田间试验研究.     

水中脲类除草剂Chlortoluron氯化产物鉴定、降解途径探究

对不同pH下Chlortoluron氯化后生成的非挥发性中间产物和挥发性产物进行了研究。对Chlortoluron氯化后的非挥发性中间产物的UPLC-ESI-MS鉴定发现了m/z为213、229、263、281、和247的离子,分析表明它们分别是Chlortoluron及其一羟基、一氯羟基、二氯和一氯衍生物。对Chlortoluron氯化后的挥发性产物采用吹扫补集-GC-MS进行分析鉴定发现了三氯甲烷(CF)、二氯硝基甲烷(DCNM)、二氯乙腈(DCAN)、1,1-2-二氯丙酮(1,1-DCP)、三氯硝基甲烷(TCNM)和1,1,1-2-三氯丙酮(1,1,1-TCP)六种消毒副产物。根据本研究中的实验结果分析和推测,在Chlortoluron的氯化过程中,苯环上和脲基链上都经历了羟基化、氧化和取代反应,接着苯环被打破,随后生成了更为有害的副产物,基于此,本文推断了Chlortoluron的氯化降解途径。     

Rain‐washing of foliar deposits of Dimilin®WP‐25 formulated in four different carrier liquids

Abstract

Dimilin^® WP‐25, a wettable powder formulation of diflubenzuron (DFB) [1‐(4‐chlorophenyl)‐3‐(2,6‐difluorobenzoyl) urea], was formulated in four different carrier liquids, viz., water; a light petroleum paraffinic oil, ID 585; a heavy paraffinic oil, Sunspray^® 7N; and a 1:2 mixture of a light petroleum aromatic solvent (Cyclosol^® 63) and canola oil; to provide four end‐use mixtures, Dim‐W, Dim‐585, Dim‐7N and Dim‐Cy‐C respectively, each containing 28 g of DFB per litre. Balsam fir branch tips clipped from greenhouse‐grown seedlings, and sugar maple branch tips clipped from field‐grown young trees, were exposed to uniform‐sized droplets (ranging in diameters from 135 to 190 μm) of the four end‐use mixtures which were atomized using a monodispersed droplet generator. Droplets were collected on the fir and maple branch tips and the initial residue per g fresh weight of foliage was determined by high‐performance liquid chromatography (HPLC). The branch tips were exposed to cumulative rainfall of 3, 6 and 10 mm at an intensity of 5 mm/h and at time intervals of 1, 12, 36 and 72 h after DFB treatment, to test the influence of ‘ageing’ of foliar residues on rainfastness. Foliar samples were collected for residue determination just before the onset of rainfall, and at 0.5 h post‐rain. DFB was quantified by the HPLC method. In the case of fir foliage, the Dim‐W formulation was the most susceptible to rain‐washing and the rainfastness did not increase with the ageing period of foliar deposits. In contrast, the three oil‐based mixtures showed greater rainfastness depending upon the carrier liquid and the ageing period. Rainfastness decreased in the order of Dim‐Cy‐C > Dim‐7N > Dim‐585 > Dim‐W. In contrast, the data on maple foliage indicated that the ageing of deposits increased the rainfastness of all the 4 end‐use mixtures. Dim‐585 was the most susceptible to rain washing, and rainfastness decreased in the order of Dim‐W > Dim‐Cy‐C > Dim‐7N > Dim‐585.