Optimal Absorbent Evaluation for the CO2 Separating Process by Absorption Loading,Desorption Efficiency,Cost, and Environmental Tolerance

The CO₂ absorption capacities of potassium glycinate, potassium sarcosinate (choline, proline), mono-ethanolamine (MEA), and tri-ethanolamine were evaluated to find the optimal absorbent for separating CO₂ from gaseous products by a CO₂ purification process. The absorption loading, desorption efficiency, cost, and environmental tolerance were assessed to select the optimal absorbent. MEA was found to be the optimum absorbent for separating the CO₂ and H₂ mixture in gaseous product. The maximum absorption loading rate was 0.77 mol CO₂ per mol MEA at temperature of 20°C and absorbent concentration of 2.5 mol/L, whereas desorption efficiency was 90% by heating for 3 h at 130°C. MEA was found to be an optimal absorbent for the purification process of CO₂ during gaseous production.     

Feasibility of honeycomb monolith supported sugar catalyst to produce biodiesel from palm fatty acid distillate (PFAD)

Carbon coated monolith was prepared by sucrose solution 65 wt.% via dip-coating method. Sulfonation of incomplete carbonized carbon coated monolith was carried out in order to synthesize solid acid catalyst. The textural structure characteristics of the solid acid catalyst demonstrated a low surface area and pore volume. Palm fatty acid distillate (PFAD), a by-product of palm oil refineries, was utilized as oil source in biodiesel production. The esterification reaction subjected to different reaction conditions was performed by using the sulfonated carbon coated monolith as heterogeneous catalyst. The sulfonation process had been performed by using vapour of concentrated H₂SO₄ that was much easier and efficient than liquid phase sulfonation. Total acidity value of carbon coated monolith was measured for unsulfonated sample (0.5 mmol/g) and sulfonated sample (4.2 mmol/g). The effect of methanol/oil ratio, catalyst amount and reaction time were examined. The maximum methyl ester content was 89% at the optimum condition, i.e. methanol/oil molar ratio (15:1), catalyst amount (2.5 wt.% with respect to PFAD), reaction time (240 min) and temperature 80 °C. The sugar catalyst supported on the honeycomb monolith showed comparable reactivity compared with the sugar catalyst powder. However, the catalyst reusability studies showed decrease in FFA% conversion from 95.3% to 68.8% after four cycles as well as the total acidity of catalyst dropped from the value 4.2 to 3.1 mmol/g during these cycles. This might be likely due to the leaching out of SO₃H group from the sulfonated carbon coated monolith surface. The leaching of active species reached a plateau state after fourth cycle.     

Safety assessment of the film boiling chemical vapor infiltration (FB-CVI) process through a system-theoretic accident model and process (STAMP)

Film boiling chemical vapor infiltration (FB-CVI) is considered as one of the fastest process methodologies for manufacturing carbon-carbon (C–C) composite products and possesses various advantages compared to conventional methodologies. However, there are safety concerns associated with this process for large-scale manufacturing, mainly owing to the intrinsic nature of the precursor and the process conditions. Considering the multifunctional interactions of the various systems during the process, a system-theoretic process analysis (STPA)/system theoretic accident model and process (STAMP) model is used to perform a safety analysis of the hazardous states of the FB-CVI process at the system level. As a case study, the FB-CVI process equipment employed for the manufacturing of C–C composites is considered. The safety constraints present in the system are assessed for adequacy through a hazard analysis by STPA/STAMP. The analysis through STPA/STAMP demonstrated the capability to create proactive strategies for the design and realization of process equipment that can be employed to manufacture C–C composite products through the FB-CVI process.     

Study on Assessing Economic Vulnerability of Small Island Regions

The main purpose of this study is to assess economic vulnerability of small island development regions as part of their sustainability constraints. By combining economic and environmental time series data, we assessed a composite index of economic vulnerability which is constructed from three exogenous variables, namely economic exposure, economic remoteness, and economic impact of environmental and natural disasters. We used the Amami Islands, Kagoshima Prefecture, Japan as the case studies for this paper.The results indicated that using a gross island products based valuation index, Kikaijima is the most vulnerable island in the Amami Islands with a composite economic vulnerability index (CEVI) value of 0.678, while by using a per capita based index, Okinoerabujima is considered the most vulnerable island with a CEVI value of 0.680. From the results we also revealed that smaller islands have relative higher vulnerability than the bigger one, which also confirms some previous country-level vulnerability studies.However, it is matter of fact that some islands that have relatively high vulnerability also have good economic performance as shown by their per capita income. In this regard, it can be argued that the success of these small islands could have been achieved in spite of and not because of their inherent vulnerability conditions as an indicator of sustainability constraint. Regarding these findings, we also examined a comparison between vulnerability results and the preliminary concept of an island's resilience in order to capture another perspective on sustainability assessment in a small island region.     

Preparation of solar-enhanced AlZnO@carbon nano-substrates for remediation of textile wastewaters

Photoactive aluminum doped ZnO(AlZnO) was synthesized by sol-gel method.After that,AlZnO photocatalyst was deposited on five carbon-based materials(CBMs) using ultrasonic route followed by solid-state mixing using ball mill.The CBMs used were poly aniline(PANI),carbon nitride(CN),carbon nanotubes(CNT),graphene(G),and carbon nanofibers(CNF).The crystal phases,elemental compositions,morphological,and optical properties of the AlZnO@CBMs composites were investigated.Experimental results revealed that two of AlZnO@CBMs composites exhibited superior bleaching efficiency(100% removal) and photocatalytic stability(three cycles) for 50 μmol/L Methylene Blue(MB) contaminated water after 60 min irradiation in visible light at pH 6.5,0.7% H_2O_2,and 5 g/L inorganic salts.Under optimum conditions,AlZnO@CBMs nanocomposites were employed for the treatment of mixed dyestuffs composed of MB,Methyl Orange(MO),Astrazone Blue FRR(BB 69),and Rhodamine B(RhB) dyes under dark,ultraviolet,visible,and direct sunlight.For mixed dyestuffs,the AlZnO@G achieved the highest dye sorption capacity(60.91 μmol dye stuffs/g) with kinetic rate 8.22 × 10~(-3) min~(-1) in 90 min via multi-layer physisorption(Freundlich isotherm) on graphene sheet.In additions,AlZnO@CN offered the highest photo-kinetic rate(K_(photo)) of～54.1 × 10~(-3) min~(-1)(93.8% after 60 min) under direct sunlight.Furthermore,the selective radical trapping experiment confirmed that the holes and oxidative superoxide radicals are crucial on dyes photodegradation pathway.Owing to their superior performance,AlZnO@G and AlZnO@CN nanocomposites can offer an effective in-situ solar-assisted adsorption/photocatalytic remediation of textile wastewater effluents.     

过硫酸钠缓释材料的释放性能及其对2, 4-二硝基甲苯的降解效果

针对原位化学氧化技术修复土壤和地下水时氧化剂因释放过快而导致的利用率低等问题,通过熔化成型法制备过硫酸钠缓释材料,分析石蜡、硅砂和过硫酸钠不同配比对材料成型度和释放性能的影响,研究缓释过程中溶液pH的变化,探讨其在水溶液中的缓释行为及其对2,4-二硝基甲苯（2,4-DNT）的降解效果.结果表明:当固定过硫酸钠质量为6 g、硅砂质量为18 g、蜡砂比（石蜡、硅砂质量之比）为1:4~1:8时,过硫酸钠缓释材料成型度适中,且过硫酸钠的累积缓释量随着时间的延长而逐渐增大,第31天时过硫酸钠累积释放百分比为74.67%~88.40%,可实现过硫酸钠的持续可控释放.当硅砂质量为18 g、蜡砂比为1:1~1:6时,过硫酸钠累积释放百分比随着过硫酸钠质量的增加而增大,且溶液中的pH呈先降低后上升的变化规律.缓释材料缓释前后实物图和显微镜分析结果显示,过硫酸钠缓释材料的释放是一个由外到内、速率由快变慢最终趋于平稳的过程.过硫酸钠质量为12 g、硅砂质量为18 g、蜡砂比为1:4的缓释材料对2,4-DNT具有较好的降解效果,第16次置换浓度为0.2 mg/L的2,4-DNT水溶液时,2,4-DNT的降解率为56.38%.研究显示,改变制备材料的配比可有效实现缓释材料中过硫酸钠的缓慢释放及对污染物的有效降解,可为原位化学氧化修复土壤和地下水提供理论支撑.      

新型防腐涂层对直升机典型结构材料防护性能研究

目的研究新型防腐涂层对直升机典型结构用铝合金及复合材料在热带海洋性气候环境下的防护性能,并与原防护涂层进行对比。方法通过测试涂层腐蚀后的形貌、光泽度、色差、电化学阻抗等,对比新/原涂层对直升机典型结构用铝合金和复合材料的防护性能。结果经过2年腐蚀后,新涂层表面无明显变化,而原涂层表面有轻微腐蚀,光泽度和色差下降较大。电化学阻抗测试表明,暴露前后涂层结构无明显变化,涂层阻抗值呈现持续下降的趋势,但是原涂层阻抗下降更快。结论新涂层对直升机典型铝合金和复合材料有更好的防护性,更加适于海洋性环境的使用。     

包装箱用碳纤维增强复合材料贮存寿命研究

目的研究碳纤维增强复合材料贮存条件下的性能变化趋势和寿命评估。方法对碳纤维增强复合材料开展四个不同温度条件下的热氧老化试验,按试验周期定期取样开展冲击性能测试,对试验数据采用寿命预估方法进行处理,对材料性能进行预估。结果通过数据计算分别得到我国热带海洋、干热沙漠等典型气候条件下的碳纤维增强复合材料贮存寿命分别为17.21~35.89年。结论碳纤维增强复合材料具有较好的贮存性能,在较为严酷的热带海洋气候和给定的失效判据条件下,寿命预计为17.21年。试验和数据处理方法可以较好地预计材料的性能变化趋势和开展寿命评估。     

乌鲁木齐市主要街道空气中一氧化碳污染规律的研究

本文通过对影响街道空气中一氧化碳污染的因素进行了大量的监测及综合分析,找出乌鲁木齐市主要街道空气中一氧化碳的污染规律,为控制我市汽车污染提供科学依据.     

库仑滴定法测定一氧化碳

本文就一氧化碳的测定条件和CO氧化过程中氧化剂的选择进行了研究。试验表明:ReAO_4-Ⅱ为氧化CO的活性催化剂,转化率可达100％(在300℃以上),本法简便,可用于空气中一氧化碳的测定和催化剂对CO活性测试。