污水处理的节能实践

采用变频技术时污水处理设备进行节能改造，使其根据污水水量、水质的变化而自动调速。将污泥机械脱水滤液与剩余污泥混合，以此来改善污泥的浓缩脱水性能。工程运行实例表明：设备的变频调速和滤液的再利用能够降低污水处理的能量消耗，提高工艺运行水平。     

国外包装废物的处理技术动向

在欧、美、日等西方国家，废包装材料已成为主要的固体废物之一，其环境污染问题日益受到关注。本文较全面地介绍废包装材料的填埋、焚烧、循环回用、再资源化利用和减少使用包装材料等五种重要技术动击与途径。还重点介绍了美国的ＰＥＴ瓶的资源再利用，以及德国建立严格的包装废物法规和完善的处理系统的概况。     

全程自养脱氮工艺的研究

以悬浮填料床作为全程自养脱氮反应器，用不含有机碳的合成氨氮废水进行反应器的启动。系统的氨氮和总氮去除率分别达80％和60％左右。通过批式实验对全程自脱氮做进一步的研究。结果表明，通过控制反应器中DO的浓度，可以控制氨氧化和反硝化的比率；当DO为0.8mg/L时，氨氮几乎完全转化为氮气，氨氧化和反硝化在此时达到了动态平衡；在低DO情况下，氨氮和亚硝氮同时存在，氨氮和总氮的转化率都大幅度的提高，说明氨氮可以亚硝氮为电子受体，在无外加有机碳源的情况下进行反硝化。     

福州市中水回用的途径和可行性分析——以洋里污水处理厂达标出水回用为例

以福州市洋里污水处理厂达标出水回用为例,阐明福州市中水回用对环境和社会发展的必要性和前景意义,从技术、经济、政策等方面深入分析了福州城市污水处理厂达标出水是稳定、安全、充足的中水水源,回用于农田灌溉、市政杂用、冲洗车辆和冲厕等多种途径是切实可行性的。     

Highly efficient and selective removal of phosphate from wastewater of sea cucumber aquaculture for microalgae culture using a new adsorption-membrane separation-coordinated strategy

● A new adsorption-membrane separation strategy is used for phosphate removal. ● PVC/Zr-BT shows a selective adsorption ability to low-concentration phosphate. ● Low concentration of P below 0.05 mg/L was achieved in actual wastewater treatment. ● Algal biomass production served as a demonstration of phosphorus recycling. Enhanced phosphorus treatment and recovery has been continuously pursued due to the stringent wastewater discharge regulations and a phosphate supply shortage. Here, a new adsorption-membrane separation strategy was developed for rational reutilization of phosphate from sea cucumber aquaculture wastewater using a Zr-modified-bentonite filled polyvinyl chloride membrane. The as-obtained polyvinyl chloride/Zr-modified-bentonite membrane was highly permeability (940 L/(m²·h)), 1–2 times higher than those reported in other studies, and its adsorption capacity was high (20.6 mg/g) when the phosphate concentration in water was low (5 mg/L). It remained stable under various conditions, such as different pH, initial phosphate concentrations, and the presence of different ions after 24 h of adsorption in a cross-flow filtration system. The total phosphorus and phosphate removal rate reached 91.5% and 95.9%, respectively, after the membrane was used to treat sea cucumber aquaculture wastewater for 24 h and no other water quality parameters had been changed. After the purification process, the utilization of the membrane as a new source of phosphorus in the phosphorus-free f/2 medium experiments indicated the high cultivability of economic microalgae Phaeodactylum tricornutum FACHB-863 and 1.2 times more chlorophyll a was present than in f/2 medium. The biomass and lipid content of the microalgae in the two different media were similar. The innovative polyvinyl chloride/Zr-modified-bentonite membrane used for phosphorus removal and recovery is an important instrument to establish the groundwork for both the treatment of low concentration phosphate from wastewater as well as the reuse of enriched phosphorus in required fields.     

Emergy analysis applied to the estimation of the recovery of costs for water services under the European Water Framework Directive

In this paper, the European Union's Water Framework Directive 2000/60/EC (WFD) that is intended to foster protection of water resources is examined, focusing on the improvement of ecological and chemical quality of surface and groundwater. The WFD includes the concept of full cost recovery (FCR) in accordance with the Polluter-Pays Principle, as one of the tools of an adequate and sustainable water resource management system. The WFD defines three different costs associated with water: resource costs (RC), financial costs (FC), and environmental costs (ECs).The FCR of water is examined from a biophysical perspective using emergy evaluation to: (1) establish resource values of water from different sources, (2) establish the full economic costs associated with supplying water, and (3) the societal costs of water that is used incorrectly; from which the resource costs, financial costs, and environmental costs, respectively, can be computed. Financial costs are the costs associated with providing water including energy, materials, labor and infrastructure. The emergy based monetary values vary between 0.15 and 1.73 €/m³ depending on technology. The emergy based, global average resource value (from which resource costs can be computed) is derived from two aspects of water: its chemical potential and its geopotential. The chemical potential monetary value of different sources such as rain, groundwater, and surface water derived from global averages of emergy inputs varies from 0.03 to 0.18 €/m³, depending on source, and the geopotential values vary from 0.03 to 2.40 €/m³, depending on location in the watershed. The environmental costs of water were averaged for the county of Spain and were 1.42 €/m³.Time of year and spatial location within the watershed ultimately influence the resource costs (computed from emergy value of chemical potential and geopotential energy) of water. To demonstrate this spatial and temporal variability, a case study is presented using the Foix watershed in northeastern Spain. Throughout the year, the resource value of water varies from 0.21 to 3.17 €/m³, depending on location within the watershed. It is concluded that FCR would benefit from the evaluation of resource costs using spatially and temporally explicit emergy accounting.     

The recycling cycle of materials as a design project tool

Currently, a large number of companies consider recycling of materials as an opportunity to maximize profits and to reduce the environmental impact generated by these materials after they are disposed. However, there is also a strong constraint on the use of recycled materials mainly due to the lack of technical/scientific information, which would relate their physical properties to their recycling cycle. This information should be used in the initial phase of the product design to serve as reference for the simulation of a project to point out the physical properties obtained from recycling the Projected material (Pm). Thus, it would be possible to foresee some recycling strategy to keep the good characteristics of recycled materials by encouraging their use, regardless of the product to be designed.Therefore, the Recycling Cycle of Materials (RCM) is a tool that provides scientific/technical support in the selection of materials. It uses the information related to the physical properties of the Pm as a parameter for product design after five recycling cycles. For the case study, this tool has been applied to obtain the basic material of ABS/PC blend. Subsequently, this blend was evaluated using DSC, FTIR, traction and impact methods to obtain delimiting data for the definition of the mechanical properties resulting from the application of RCM.     

Exploring full cost accounting approach to evaluate cost of MSW services in India

Municipal solid waste (MSW) services of developing countries often suffer due to the lack of financial and operational autonomy, scientific approach, and adequate levels of resources. The solid waste management (SWM) practices of developed countries are benefited in cost and efficiency due to the participation of private players and sound financial management. However, developing economies depend on local municipalities to own and operate SWM services amidst structural and financial inefficiency. With the demands of augmenting efficient and cost-effective SWM services to the expanding population of cities and towns of newly industrialized nations on the rise, the municipalities in these countries are under pressure to adopt ways and means that can support efficient utilization of resources and improved decision-making capabilities. This research article reflects the current state of the MSW services in India and explores full cost accounting (FCA) framework in its ability to generate information on cost-related aspects and sustainable deployment of resources. Lastly, the extensibility of FCA is tested by integrating externalities of MSW services.     

The Potential of Using Solar Energy to Process Full-Fat Soybeans (Glycine max) to Reduce Urease Activity

The objective of this study was to investigate the efficacy of panel solar cookers in reducing urease activity in full-fat soybeans (Glycine max). Changes in urease activity of soaked (SM), coarse-milled (CM) and whole dry (WM) full fat soybeans were investigated by roasting for 0, 30, 60, 90, 120, 150 and 180 min in multiple reflector panel solar cookers, in a 3 3 3 factorial experiment. Soaking soybeans for 14 h reduced (p<0.05) ^{1 1}P < 0.05 means that the probability (p) of falsely concluding significant difference between values obtained after statistical analysis was less than 5% (0.05). urease activity by 9%, from 6.58 meqNH₃/g DM to 5.98 meqNH₃/g DM. After 180 min of solar roasting, urease activity levels had declined by 81%, 67% and 23% in soaked, milled and whole dry soybeans respectively. Full fat soybean urease activity can be reduced faster in soaked than in dry soybeans. Findings suggest that there is potential in using multiple reflector panel solar cookers to reduce urease activity in full fat soybeans.     

Status of recycling end-of-life vehicles and efforts to reduce automobile shredder residues in Korea

The present end-of-life vehicle (ELV) recycle rate and management status during the dismantling stage were investigated to aid the establishment of policies for the management of ELVs by surveying information and using the results gained from questionnaires given to dismantlers. The average recycle rate at the dismantling stage was 44% of the mass of a new vehicle and the rest of the ELV was then compressed and transported to shredding companies to recover mainly the iron content, which averaged 38.7% of the mass of a new vehicle. Nonferrous metals such as copper, antimony, zinc, and aluminum accounted for only 1.5%. The automobile shredder residues (ASRs) were composed of light and heavy fluffs and soil/dust and amounted to 15.8% based on the mass of a new vehicle. The dumping of fluff and inorganic residues in landfill sites, however, will be restricted when new regulations are implemented to reduce the disposal amount to less than 5% of a new car, as has been done in European countries and in Japan. The detailed characteristics of ASR were investigated to suggest appropriate means of treatment such as volume reduction or the utilization of thermal technologies to meet future expected enforcement. Also, some concerns on hazardous pollutant release such as that of dioxins while utilizing such thermal treatment methods were considered. The present on-going research and development projects to meet such future management targets are also introduced.