布、洛、维、肖氏硬度的相关关系

进行了布、洛、维、肖氏硬度之间的回归分析,建立了洛氏硬度与布氏、维氏、肖氏硬度之间,以及布氏硬度与维氏、肖氏硬度之间的回归关系式.     

地面水中氨,硝酸盐,亚硝酸盐,氯化物,正磷酸盐,总硬度和硅酸盐的同时测定

用AQUA800辨别分析仪同时测定地面水中的氨、硝酸盐、亚硝酸盐、氯化物、正磷酸盐、总硬度和硅酸盐,是一种简便、迅速、准确、可靠的测定方法,样品无需预处理,精密度试验其变异系数分别为1．24％、2．18％、2．02％、2．67％、2．35％、3．57％、4．78％,加标回收率分别为103．5％、101．0％、95．0％、99．2％、97．6％、101．5％、98．0％,方法检测限分别为氨0．022mg／L,硝酸盐0．015mp／L,亚硝酸盐0．002tug／L,氯化物0．47mg／L,正磷酸盐0．015mg／L,总硬度17．6mg／L,硅酸盐0．55mg/L,能满足地面水中辨别分析仪同时测定氨、硝酸盐、亚硝酸盐点化物、正磷酸盐、总硬度和硅酸盐分析测定的要求。     

Characterisation and Nanomechanical Properties of Ink-Jet Media Using Atomic Force Microscopy

Commercial inkjet media is increasingly used in daily life; this use ranges from offices to digital photography. The impact that the development of this technology has had on the paper industry has been phenomenal. However, an increasing amount of paper is discarded and it is often after the introduction of complex chemical ink within its substrate. The understanding of the interactions between the layer of coated media and ink can be used to further understand and develop technology for the use of recycling office and photo papers. This paper presents the innovative concept in characterizing the surface of the inkjet media by atomic force microscopy (AFM) and scanning electron microscopy (SEM). Comparisons are made between the data obtained from both atomic force microscopy and scanning electron microscopy of the receptive layer and surface analysis software that was used to obtain surface characteristics. In this study the hardness and force of interaction has also been examined by the means of nanoindentation measurements using silicon nitride cantilever tips and forces of interaction between a selection of colloid probes and the receptive layer of the inkjet media. The effect of loading force on indentation was studied in terms of approach of impact and type of media tested.     

提高冷拔内模使用可靠性的研究

用安全学科的观点 ,对冷拔内模进行宏观痕迹分析和磨损失效模式的确定 ,并结合摩擦学精典的磨损理论 ,对冷拔内模进行微观磨损机理分析 ,从而为提高冷拔内模使用可靠性提供了理论依据和有效措施。     

硬度测量法测定20号钢球化等级的实验

为快速、便捷地获得20号钢球化等级,避免传统金相组织观察比对法存在主观判断偏差和制作金相试样的过程烦琐,实验采用简易的硬度测量法对20号钢的硬度进行测量,并对测量数据进行相关性分析,得到20号钢平均硬度值与球化等级线性负相关的特性。采用最小二乘法拟合得到20号钢平均硬度值与球化等级的线性回归关系式,并据此关系式实现对未知球化等级的20号钢进行测定。通过硬度测量法测定的未知球化等级20号钢,与金相组织观察比对法的评定结果基本吻合。     

便携式布氏硬度计在电厂金属硬度检测中的应用

针对电厂金属部件及焊缝现场硬度检测中里氏硬度计误差较大的问题,介绍了有关标准的进展情况,以及便携式布氏硬度计和压痕自动测量装置的最新技术.结果表明:在现场硬度检测中,对有争议的硬度值宜采用便携式布氏硬度计进行测量校核,国内已形成关于便携式布氏硬度计的标准体系,自动压痕测量装置配合便携式布氏硬度计非常适于电厂的现场硬度检测,通过换算得到的数据,不能作为投诉和满足验收要求的依据.     

膜分离稀土废水预处理中钙镁去除的研究进展

稀土废水成分复杂,硬度高,利用膜法处理时,进膜之前必须进行预处理.介绍了降低稀土废水硬度传统的和新型的方法.经过分析得出,根据具体水质情况,选择适当的互补处理方法,稀土废水完全可达到膜分离装置进水水质要求.     

A Simple Stream Monitoring Technique Based on Measurements of Semiconservative Propertiesof Water

Correlative relationships exist among conductivity, alkalinity, and hardness in streams due to natural geological and climatological controls, but the relationships among these three water-quality factors can be altered strongly by inputs of ion-rich wastewaters. The degree of alteration can be monitored conveniently by use of a simple chemical perturbation index, computed by subtracting the sum of rank pairwise correlations among the conductivity, alkalinity, and hardness (for observations on each of these variables, measured through time) from 3.0. The chemical perturbation index can be used to document or characterize spatiotemporal changes in stream water quality. This study explains the development of the index's concept and provides examples of its application in an extensive stream monitoring program used to assess ecological conditions in streams on the Department of Energy's Oak Ridge Reservation in east Tennessee, USA. The chemical perturbation index technique may be particularly useful in community-based stream monitoring programs because to its simplicity and low cost.     

油田采出水用于热采蒸汽发生器给水的研究

提出了低含盐、负硬度油田采出水和高含盐、非碳酸盐硬度油田采出水回用于热采蒸汽发生器的工艺路线。在实验室的研究重点为：１．采出水的活性炭深度脱油；２．低含盐、负硬度油田采出水的石灰软化一离子交换树脂脱硬度；３．高含盐、非碳酸盐硬度油田采出水石灰－纯碱软化－离子交换树脂脱硬度。     

Water softening by induced crystallization in fluidized bed

Fluidized bed and induced crystallization technology were combined to design a new type of induced crystallization fluidized bed reactor. The added particulate matter served as crystal nucleus to induce crystallization so that the insoluble material, which was in a saturated state, could precipitate on its surface. In this study, by filling the fluidized bed with quartz sand and by adjusting water p H, precipitation of calcium carbonate was induced on the surface of quartz sand, and the removal of water hardness was achieved.With a reactor influent flow of 60 L/hr, a fixed-bed height of 0.5 m, pH value of 9.5, quartz sand nuclear diameter of 0.2–0.4 mm, and a reflux ratio of 60%, the effluent concentration of calcium hardness was reduced to 60 mg/L and 86.6% removal efficiency was achieved. The resulting effluent reached the quality standard set for circulating cooling water. Majority of the material on the surface of quartz sand was calculated to be calcium carbonate based on energy spectrum analysis and moisture content was around 15.994%. With the low moisture content, dewatering treatment is no longer required and this results to cost savings on total water treatment process.