Tuning the fill percentage in the hydrothermal synthesis process to increase catalyst performance for ozone decomposition

The performance of Ce-OMS-2 catalysts was improved by tuning the fill percentage in the hydrothermal synthesis process to increase the oxygen vacancy density. The Ce-OMS-2 samples were prepared with different fill percentages by means of a hydrothermal approach (i.e. 80%, 70%, 50% and 30%). Ce-OMS-2 with 80% fill percentage (Ce-OMS-2-80%) showed ozone conversion of 97%, and a lifetime experiment carried out for more than 20?days showed that the activity of the catalyst still remained satisfactorily high (91%). For Ce-OMS-2-80%, Mn ions in the framework as well as K ions in the tunnel sites were replaced by Ce⁴⁺, while for the others only Mn ions were replaced. O₂-TPD and H₂-TPR measurements proved that the Ce-OMS-2-80% catalyst possessed the greatest number of mobile surface oxygen species. XPS and XAFS showed that increasing the fill percentage can reduce the AOS of Mn and augment the amount of oxygen vacancies. The active sites, which accelerate the elimination of O₃, can be enriched by increasing the oxygen vacancies. These findings indicate that increasing ozone removal can be achieved by tuning the fill percentage in the hydrothermal synthesis process.     

Relationship between physicochemical properties and dewaterability of hydrothermal sludge derived from different source

Sewage sludge (SS) and deinking sludge (DS) were used to comparatively study the hydrothermal dewatering of sludge with different components. For a better overview, an insight into the relationship between physicochemical properties and dewaterability of hydrothermal sludge was provided. Results found that not all kinds of sludge were suitably conditioned by hydrothermal treatment (HT) in term of the elevation of dewaterability. Higher hydrothermal temperature tended to enhance the dewaterability of SS rather than DS, which was supported by the variation of their physicochemical properties (including water distribution, bonding energy, extracellular polymeric substance (EPS), particles size, acid functional groups and zeta potential in this study). In addition, the changes in surface morphology suggested that the reverse effect of HT on sludge dewaterability was mainly due to their dewatering behavior. For SS, the destruction of EPS structure leaded to the release of bound water, thereby strengthening sludge dewatering. Conversely, “Bridging effect” generated by lignocellulose in DS was beneficial for sludge dewatering; however, the increasing hydrothermal temperature degraded part of lignocellulose and weakened “bridging effect”, finally resulting in worse dewaterability of DS.     

铜镍电镀污泥的资源化与无害化处理试验研究

提出了铜镍电镀污泥的资源化与无害化处理的工艺流程 ,并用试验考察了各工序的技术经济指标。试验结果表明 ,铜粉品位大于 90 % ,铜的回收率大于 95 % ,硫酸镍质量达到工业一级 ,镍回收率大于 80 % ,浸出渣和净化渣经固化处理后可作普通建筑材料使用 ,工艺过程产生的废水可以达标排放     

固化法处理废干电池

介绍了电池的历史及其生产的现状、排废特征 ;简述了废旧干电池对环境的危害及其回收处理工艺和经济环境效益 ;结合金霸王 (中国 )有限公司废干电池的特点和电池废料的处理现状 ,对其采用固化法处理 ,然后进行渗漏试验并作出结果分析和评述 ;最后对废干电池的回收处理提出建议。     

医疗废物焚烧残余物固化技术初探

根据对医疗废物焚烧残余物中有毒有害物质的化验分析结果,确定焚烧残余物中有毒有害成分含量仍较高,部分指标超出标准值,必须对其进行稳定化/固化处理,避免对土壤及地下水环境造成污染.本文阐述了稳定化/固化处理原理及处理工艺,使医疗废物无害化、减量化和资源化的处理原则得以全面实现.     

熔池高度对双辊薄带凝固组织影响的模拟预测

在已建立的理论数学模型的基础上,以1Cr18Ni9Ti不锈钢为研究对象,模拟预测了薄带厚度保持不变条件下熔池高度对薄带凝固组织的影响。研究结果表明:随着熔池高度增加,1Cr18Ni9Ti不锈钢双辊薄带凝固组织中柱状晶区比例首先增大,然后又逐渐减小。而柱状枝晶取向度和枝晶间距则随着熔池高度的增加而增大,但在较低的熔池高度条件下,柱状枝晶间距在凝固结束时有突然增大的趋势。     

雾化合金液滴的凝固动力学分析与计算

雾化凝固过程对雾化制粉和喷射沉积材料的组织有重要影响。雾化凝固过程主要由液态冷却、再辉、偏析凝固、共晶凝固与固态凝固阶段组成。分析了雾化过程中的液滴的速度与粒度分布及凝固各阶段液滴凝固潜热的释放与环境导热之间的热平衡。     

印刷线路板厂含铜污泥固化处理工艺研究

研究采用水泥作固化基材固化处理某印刷线路板厂酸性废水用石灰混凝所产生的含铜、锡、金的污泥 ,对固化块在不同 pH的水中重金属Cu2 +的浸出实验结果表明 :水泥固化处理该混凝污泥效果良好 ,控制合适的条件 ,可得到混合性能好、初凝时间适当、抗压强度较好的固化块。Cu2 +的浸出率低于允许浸出浓度。混凝过程中加入硫脲硅酸钠等助剂 ,可提高固化效果。研究还对几种不同配比的固化块抗压强度进行了探讨。     

城市生活垃圾焚烧飞灰熔融处理的进展

针对城市生活垃圾焚烧产生飞灰的处理以及由此引发的二次污染问题,阐述了飞灰的污染特性,讨论了各种飞灰处理技术的优缺点,分析了熔融处理技术在降低飞灰中重金属浸出毒性和彻底分解其中的二恶英所具有的优越性,为飞灰的无害化和资源化处理提供参考。     

油田废污泥治理研究

冀东油田废水池地处环境敏感区域，对其废污泥采用固化法进行处理。在大量实验的基础上优选出了三种固化剂体系并通过多次浸泡实验、淋洗实验和静态浸出实验对固化效果进行了分析。