乙醇汽油与普通汽油非常规污染物排放特性对比研究

在一台满足国Ⅴ排放标准的双喷射(气口喷射+缸内直喷)汽油机上开展了燃用E10乙醇汽油(乙醇体积比为10%)对发动机非常规排放特性影响的试验研究.使用傅里叶变换红外分析仪(FTIR)测量了饱和烃、不饱和烃、芳香烃及醇、醛等非常规污染物排放量,对比分析了双喷射模式时各工况下E0和E10两种燃料的非常规排放水平.结果表明,双喷射模式下,加入乙醇有效降低了乙烯、1,3-丁二烯、苯和甲苯的排放量,但会导致乙醛排放升高.双喷射模式下,随着负荷增加,两种燃料下的1,3-丁二烯和甲苯排放呈现先升高后降低的趋势,乙烯、甲醛和苯排放则先降低后升高.乙醇能抑制1,3-丁二烯、乙烯生成,抑制效果为PFI模式优于双喷射模式,GDI模式抑制量最低.PFI和GDI模式下E10的甲醛排放均显著升高,但双喷射模式有效抑制了甲醛排放的增加.     

金属表面涂装行业VOCs排放特征及排放系数

对比了浙江省2014和2018年金属表面涂装企业的有机废气排放及治理情况,分析了该行业涂料及稀释剂的使用、主要污染因子,测算了溶剂型、水性涂料的挥发性有机物（VOCs）产生系数和排放系数.结果表明：2018年VOCs治理水平明显高于2014年,水性涂料使用企业比例由18%上升至36%,纯溶剂型企业由82%下降至64%;金属表面涂装行业的主要排放污染物为二甲苯、丁醇、乙酸乙酯、乙酸丁酯、甲苯、丙二醇、乙苯、苯乙烯等8种有机物.溶剂型和水性涂料的VOCs产生系数分别为0.72和0.31kg/kg;溶剂型和水性涂料2014年VOCs排放系数为0.64和0.29kg/kg,2018年为0.48和0.21kg/kg.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

新型防腐涂层对直升机典型结构材料防护性能研究

目的研究新型防腐涂层对直升机典型结构用铝合金及复合材料在热带海洋性气候环境下的防护性能,并与原防护涂层进行对比。方法通过测试涂层腐蚀后的形貌、光泽度、色差、电化学阻抗等,对比新/原涂层对直升机典型结构用铝合金和复合材料的防护性能。结果经过2年腐蚀后,新涂层表面无明显变化,而原涂层表面有轻微腐蚀,光泽度和色差下降较大。电化学阻抗测试表明,暴露前后涂层结构无明显变化,涂层阻抗值呈现持续下降的趋势,但是原涂层阻抗下降更快。结论新涂层对直升机典型铝合金和复合材料有更好的防护性,更加适于海洋性环境的使用。     

纳米涂层/铝合金在不同pH值的海水溶液中的腐蚀行为研究

目的评价纳米涂层/铝合金在不同pH值海水溶液中的腐蚀行为。方法通过测试纳米涂层/铝合金试样在不同pH值海水溶液中的EIS值,分析试样阻抗谱图及Bode谱图的演化规律,建立不同EIS图谱的不同电极阻抗模型,并采用ZView软件解析涂层体系不同时期的电化学阻抗谱,获得涂层电阻的变化趋势,及不同pH值海水浸泡的纳米涂层体系腐蚀失效速度。结果随着浸泡时间的增加及pH值的降低,纳米涂层/铝合金体系腐蚀损伤失效速率在浸泡前期整体趋势增大,但中后期由于腐蚀产物逐渐堵塞了涂层的微孔,腐蚀介质向铝合金表面渗透的速率逐渐减小。结论 pH为2.0海水浸泡下的3涂层失效最快,其次是pH为4.0海水浸泡下的2涂层,最后为p H为6.0海水浸泡下的1涂层,该涂层体系应采用等效电路模型C进行拟合。     

Potential of secondary aerosol formation from Chinese gasoline engine exhaust

Light-duty gasoline vehicles have drawn public attention in China due to their significant primary emissions of particulate matter and volatile organic compounds(VOCs). However,little information on secondary aerosol formation from exhaust for Chinese vehicles and fuel conditions is available. In this study, chamber experiments were conducted to quantify the potential of secondary aerosol formation from the exhaust of a port fuel injection gasoline engine. The engine and fuel used are common in the Chinese market, and the fuel satisfies the China V gasoline fuel standard. Substantial secondary aerosol formation was observed during a 4–5 hr simulation, which was estimated to represent more than 10 days of equivalent atmospheric photo-oxidation in Beijing. As a consequence, the extreme case secondary organic aerosol(SOA) production was 426 ± 85 mg/kg-fuel, with high levels of precursors and OH exposure. The low hygroscopicity of the aerosols formed inside the chamber suggests that SOA was the dominant chemical composition. Fourteen percent of SOA measured in the chamber experiments could be explained through the oxidation of speciated single-ring aromatics. Unspeciated precursors, such as intermediate-volatility organic compounds and semi-volatile organic compounds, might be significant for SOA formation from gasoline VOCs. We concluded that reductions of emissions of aerosol precursor gases from vehicles are essential to mediate pollution in China.     

石墨烯在防腐涂料中的研究进展及应用

简要叙述了石墨烯结构性能以及当前主流制备石墨烯的方法。概述了最近几年来石墨烯在防腐涂料中的研究进展情况,包括石墨烯在涂料中的添加量、分散技术、原位改性等对涂料性能的影响。研究表明,在涂层中分散均匀添加量适中的石墨烯可以对防腐涂料性能有较大的提升,探讨了石墨烯在防腐涂层中的应用机理,同时对石墨烯防腐涂料的应用发展进行了展望。     

基于SOM-SVM组合分类器的涂层防护性能研究

目的为避免EIS,EN技术可能出现的问题,建立一个准确、高效的评价模型,以探究现役军用有机涂层防护性能。方法利用电化学阻抗谱(EIS)、电化学噪声(EN)技术分析了两种军车有机涂层在循环暴露试验中的腐蚀行为,提取低频阻抗模值|Z|_(0.1 Hz)与涂层噪声电阻R_n两种电化学评价参数作为自组织神经网络(SOM)的输入训练样本,同时结合支持向量机(SVM)方法建立涂层防护性能组合分类器。结果将涂层失效过程自适应地分为涂层防护性能良好、防护性能下降、基本失效三个阶段。结论所建立的SOM-SVM组合分类器对于辅助分析涂层防护性能具有可行性。     

DZ125合金HY3包覆型涂层退除研究

目的 研究化学法退除DZ125合金HY3包覆型涂层。方法 采用真空电弧镀技术（AIP）在定向凝固镍基高温合金DZ125上制备包覆型涂层HY3,利用化学方法完全退除基体上的涂层,通过失重法研究对比1#和2#退除溶液退除HY3涂层和DZ125合金的退除速率,采用扫描电镜（SEM）对退除后的HY3涂层和DZ125基体的微观组织进行观察。结果 经过100 min,2#溶液可以将20 ?m左右的HY3涂层完全退除,采用1#溶液需要超过100 min才能完全退除涂层。两种对DZ125合金的腐蚀性很小,对于同一种合金而言,1#溶液和2#溶液对合金的腐蚀速率比值为1︰13。在1#溶液中,合金与涂层腐蚀速率的比值为1︰87.65;在2#退除溶液中,合金与涂层腐蚀速率的比值为1︰6.81。结论 1#溶液更加适合退除DZ125合金上的HY3涂层。     

柴油机尾气中PAH_s的分析

本文概述了柴油机尾气中ＰＡＨｓ的分析方法，着重论述了采样及预处理方法，特别对预处理方法进行了深入的探讨。另外，通过对柴油机两种不同工况下产生的尾气进行分析后发现，柴油机转速越高，其排放尾气中ＰＡＨｓ的含量就越低。