内质网应激在氟暴露致小鼠睾丸损伤中的作用

探讨了内质网应激在亚慢性氟暴露致小鼠睾丸损伤中的作用及分子机制.选用健康初断乳ICR雄性小鼠30只,随机分为对照组（C）、低氟组（LF）和高氟组（HF）,分别饮用自来水、5、30 mg·L^-1氟化钠水溶液90 d.亚慢性氟暴露结束后,以睾丸脏器系数、睾丸组织氧化/抗氧化酶和形态结构、精子质量、睾丸细胞凋亡、葡萄糖调节蛋白78（GRP78）、CCAAT/增强子结合蛋白同源蛋白（CHOP）、半胱氨酸天冬氨酸蛋白酶12（CASPASE-12）、半胱氨酸天冬氨酸蛋白酶3（CASPASE-3）为观测点.结果表明,与对照组比,LF组和HF组LDH、SOD、T-AOC活性下降,MDA含量上升,HF组GSH-PX活性下降,差异有统计学意义（p<0.05或p<0.01）;LF组可见细胞层次减少、间隙变大,成熟精子数量减少,HF组细胞溶解、层次紊乱,空泡化严重,少见成熟精子;LF组和HF组小鼠的精子活力降低,HF组小鼠精子数量下降,畸形率上升,差异有统计学意义（p<0.05或p<0.01）;LF组和HF组睾丸细胞凋亡指数上升,差异有统计学意义（p<0.01）;LF组和HF组Grp78、Caspase-12、Caspase-3基因表达水平上升,差异有统计学意义（p<0.05或p<0.01）.结果提示,除氧化应激以外,Caspase-12和Caspase-3基因表达异常可能是氟暴露致小鼠睾丸细胞凋亡异常的分子机制之一.     

金属改性对SAPO-34低温还原NO性能的影响

采用浸渍法制备金属改性SAPO-34分子筛催化剂,分析比较了不同单金属（Cu或Co）及不同比例双金属（Cu：Co=1：1、3：1、5：1,质量比）改性催化剂对NO的催化还原性能,评价了不同催化剂的N₂选择性,并采用扫描电子显微镜（SEM）、比表面积测试、X射线衍射分析（XRD）、NH₃-程序升温脱附（NH₃-TPD）等表征手段对催化剂的物化性能进行了分析.结果表明,单金属Cu改性催化剂具有较宽的温度区间,在250~450℃范围内NO的转化率始终保持在100%;双金属改性使NO转化率保持为100%的最低温度下降了25~50℃,显著拓宽了低温段窗口,其中,Cu₃Co₁/SAPO-34催化剂的低温催化还原性能最好,200℃即可实现100%的NO转化率,175℃下的转化率也高达80%以上.Cu-Co双金属改性SAPO-34分子筛催化剂具有优异的低温催化还原NO性能,具有在机动车尾气、工业废气的低温脱硝治理领域应用的潜力.     

稻田NO3-还原耦合As(III)氧化过程及微生物群落特征

以华南稻田土壤为研究对象通过构建微宇宙体系,研究了淹水稻田自养硝酸盐还原耦合As（III）氧化过程及其微生物群落结构组成.结果表明,NO₃^-的添加促进了稻田土壤中As（III）的氧化,在未添加NO₃^-的处理（Soil+As（III））以及灭菌处理（Sterilized soil+As（III）+NO₃^-）中As（III）未发生明显的氧化;在Soil+As（III）+NO₃^-处理中,NO₃^-有少量被还原,而在Soil+NO₃^-处理中,NO₃^-没有被还原.通过16S rRNA高通量分析在NO₃^-还原耦合As（III）氧化体系中微生物群落结构特征,在Soil+As（III）+NO₃^-处理中shannon指数相对较低为8.19,土壤微生物群落多样性降低,其中在门水平上主要优势菌群为变形菌门Proteobacteria（33%）、绿弯菌门Chloroflexi（11%）、浮霉菌门Planctomycetes（12%）;在属水平上主要的优势菌属为Gemmatimonas（7.4%）以及少量的Singulisphaera、Thermomonas、Bacillus.NO₃^-的添加能够促进稻田土壤中自养As（III）氧化,并且影响着稻田土壤中微生物群落组成.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

Density functional theory (DFT) studies of vanadium-titanium based selective catalytic reduction (SCR) catalysts

Based on density functional theory (DFT) and basic structure models, the chemical reactions on the surface of vanadium-titanium based selective catalytic reduction (SCR) denitrification catalysts were summarized. Reasonable structural models (non-periodic and periodic structural models) are the basis of density functional calculations. A periodic structure model was more appropriate to represent the catalyst surface, and its theoretical calculation results were more comparable with the experimental results than a non-periodic model. It is generally believed that the SCR mechanism where NH₃ and NO react to produce N₂ and H₂O follows an Eley-Rideal type mechanism. NH₂NO was found to be an important intermediate in the SCR reaction, with multiple production routes. Simultaneously, the effects of H₂O, SO₂ and metal on SCR catalysts were also summarized.     

短期干旱胁迫对马尾松排放挥发性有机物的影响

为探究干旱环境对BVOCs排放的影响,应用动态封闭式采样系统和热脱附-气相色谱-飞行质谱仪,对短期干旱胁迫作用下马尾松的BVOCs排放进行了实验室测量,定量分析BVOCs排放速率和排放组成的变化.结果表明,干旱胁迫时异戊二烯的排放受到抑制,排放速率降低约50%;单萜烯和倍半萜烯的排放水平增强,排放速率分别为137.85和0.98μg/（m²·h）,是未受胁迫时的2.9和2.0倍.除反式-α-香柠檬烯外,干旱胁迫促进各单萜烯和倍半萜烯化合物的排放,是未受胁迫时的1.3~42.4倍,其中3-蒈烯排放的响应最敏感,α-葑烯、α-水芹烯和石竹烯的响应最弱.干旱胁迫时单萜烯和倍半萜烯的排放组成有所变化,但主导的化合物种类不变,单萜烯以α-蒎烯、香桧烯和β-蒎烯为主,占比分别为48%、17%和17%;倍半萜烯以石竹烯和长叶烯为主,占比分别为57%和34%.     

海水中阴极极化对X80钢应力腐蚀及氢脆敏感性的影响

目的研究不同p H值海水中阴极极化对X80管线钢应力腐蚀及氢脆的抑制作用。方法采用慢应变速率拉伸试验、电化学测试、微观组织观察等分析方法。结果 X80钢在天然海水中的析氢电位约为-940m V(vs.SCE,下同),海水p H为3.5时析氢电位发生正移。其应力腐蚀敏感性与极化电位有很大关系,随着极化电位负移,X80钢的氢脆敏感性增加。天然海水中当极化电位负于-950 m V时,断口出现准解理断裂特征形貌。在-1050 m V极化电位下,钢材进入氢脆断裂区发生脆性断裂。海水p H为3.5时,-900 m V钢材有发生氢脆的危险。结论与天然海水相比,X80钢在p H为3.5的酸性海水中具有较高的应力腐蚀敏感性,两种海水介质中X80钢的应力腐蚀敏感性均随极化电位负移而增加。     

玻璃纤维-铝合金层合板氙灯老化性能研究

目的研究氙灯环境对玻璃纤维-铝合金层合板性能的影响。方法通过研究玻璃纤维-铝合金层合板在氙灯老化后的力学性能、基体红外光谱、铝合金表面形貌及元素变化,分析层合板的氙灯老化机理。结果随氙灯老化时间的延长,树脂基体老化降解程度越高,树脂与纤维、铝合金的界面强度下降,使材料拉伸及弯曲性能降低,拉伸强度受老化影响最为显著的是正交结构层合板,老化84 d后强度降低13.7%,正交结构0°方向层合板的弯曲强度受氙灯老化影响降低4.6%,其他试样的弯曲强度降幅均低于5%,氙灯老化后的铝合金层表面的微凹坑数量及尺寸无明显变化,但凹坑氧元素随老化周期延长略微增加。结论氙灯环境主要影响玻璃纤维-铝合金层合板中的复合材料层及各界面,树脂基体的降解导致力学性能的衰退,而对于铝合金的影响并不明显。     

铍青铜弹簧片应力腐蚀断裂研究

目的研究传感器微动开关弹簧片应力腐蚀的机理,找到断裂原因。方法对弹簧片进行断口形貌观察、能谱成分分析,并进行产品模拟腐蚀实验。结果传感器内部意外进入雨水,在工作温度下形成湿热环境,开关盒中的游离氨在此环境下释放出来,在开关盒内部形成潮湿氨气氛,铍青铜弹簧片工作时凹面一侧承受静拉应力作用,从而在潮湿氨和拉应力共同作用下发生应力腐蚀开裂。结论通过采用无氨酚醛塑料制备开关盒,弹簧片的应力腐蚀得到了有效预防。     

Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.