UV/Fenton降解染料橙黄Ⅱ的脱色研究

以偶氮染料橙黄Ⅱ为对象,研究Fenton反应和紫外光辐射条件下,废水初始pH值、H2O2浓度,Fe2+浓度及反应物初始浓度对橙黄Ⅱ脱色效果的影响.结果表明,紫外光与Fenton试剂有明显协同作用,以紫外灯UV254为光源,橙黄Ⅱ质量浓度20 mg/L、pH=3.0、H2O2浓度0.2 mmol/L、Fe2+浓度0.04 mmol/L、反应40 min条件下,橙黄Ⅱ的脱色率为95%,比传统Fenton试剂的脱色率提高了15%.本研究为实际染料废水的治理提供了一种新方法.     

负载型颗粒活性炭催化过硫酸钠氧化降解橙黄G

通过在颗粒活性炭(GAC)上负载氧化铁,并以此作为催化剂(Fe/GAC)在常温常压下催化过硫酸钠(PS)产生硫酸根自由基降解偶氮染料橙黄G.研究了体系pH、氧化剂浓度、催化剂浓度对橙黄G去除率的影响,并且对催化剂的重复使用性能进行了测试.结果表明,在Fe/GAC/PS体系中,[OG]0=0.2 mmol/L,[GAC] =1 g/L,[PS]0=2 mmol/L,降解2h后OG去除率为99％,且有较高的矿化率;随着氧化剂浓度和催化剂浓度的增加,OG的去除效率提高;催化剂有较好的重复使用性.利用扫描电镜(SEM)对催化剂进行了表征,可以看出在活性炭上成功负载氧化铁.利用化学分子探针竞争实验鉴定催化反应中的活性物种SO4-·和OH·.     

混凝辅助电化学法处理橙黄G染料废水

以石墨板为阳极,研究了电化学氧化法对橙黄G染料废水的降解效果。比较了在NaCl、Na2 SO4以及NaCl与FeSO4·7H2O组合的支持电解质体系中的处理效果,同时考察了电压、初始pH、电解质浓度、电极间距和电解时间等因素对废水中橙黄G脱色率及COD去除率的影响。研究结果表明,橙黄G的脱色主要是活性氯的氧化作用,橙黄G分子的矿化可能主要是电解过程中产生的·OH的作用,FeSO4·7H2O的加入增加了混凝作用,使得处理效果进一步提高。最佳脱色条件下橙黄G脱色率和COD的去除率分别为97．6％和56．3％,B／C（BOD／COD）由0．09提高至0．41,可生化性有较大改善,并且随着降解时间的增加,COD去除率逐渐升高。此结果表明,橙黄G废水COD的去除相对于脱色存在滞后性。     

萃取净化电镀含镉废水

研究了二壬基萘磺酸(DNNSA)形成的微乳液从模拟含镉废水中萃取镉离子的工艺条件。分别考察了相体积比(O/A)、萃取时间、温度及萃取剂浓度对废水中镉离子萃取的影响。结果表明,萃取平衡时间为10 mim,降低温度及增加萃取剂浓度均有利于萃取。紫外光谱证实当DNNSA萃取镉时,所形成萃合物对萘环的结构无影响,且不会破坏微乳相的结构;分子荧光光谱表明镉离子对配体DNNSA有荧光猝灭作用。     

不同因素对多硫化钙处理地下水中Cr(Ⅵ)效果影响

选用多硫化钙为还原剂,进行地下水中Cr(Ⅵ)去除效果的研究。主要考察了多硫化钙投加量、溶液p H、温度、Mn(II)、Fe(III)、腐殖酸(HA)存在条件下,对多硫化钙处理Cr(Ⅵ)效果的影响。结果表明:当多硫化钙与Cr(Ⅵ)的摩尔比由1∶1变到5∶1时,去除率从41.03%增加到100.00%;溶液p H值从6.0增上升到9.0时,去除率下降27.16%;水环境温度由(7±1)℃增加到(27±1)℃时,去除率达到100.00%所需反应时间,缩短了4~6倍;当地下水中含有Mn(II),随着Mn(II)质量浓度升高(0.00~10.00 mg·L-1),Cr(Ⅵ)浓度低于检测线所需要的时间缩短3倍;当地下水中含有Fe(III),Fe(III)质量浓度从0.00 mg·L-1增加到10.00 mg·L-1,去除率增加9.05%;当地下水中含有HA(0.00~15.00 mg·L-1),去除率由99.31%降低至90.28%。(7)多硫化钙与六价铬的反应产物的X射线衍射光谱图像中2θ值为18.2°、19.36°、26.67°与Cr(OH)3,2θ值为23.02°与单质S的标准卡片匹配度较高。另外,对含有11.36 mg·L-1 Cr(Ⅵ)实际污染地下水的处理效果表明,Cr(Ⅵ)的去除率达到99.78%,残留浓度达到GB/T 1448—1993地下水质量标准III类标准,说明多硫化钙修复实际铬污染地下水具有良好的应用前景。     

介质阻挡放电等离子体老化微塑料及对Zn (II)吸附的影响

为了在实验中缩短微塑料的老化时间,更真实地模拟自然老化条件,采用介质阻挡放电（DBD）等离子体老化聚乙烯微塑料（PE-MP）和聚丙烯微塑料（PP-MP）,同时研究了老化前后PE-MP和PP-MP对Zn （II）的吸附过程和机理.随着放电时间延长和输入电压升高,微塑料表面出现微小裂纹或孔洞,形成含氧官能团.老化后PE-MP和PP-MP对Zn （II）的吸附容量分别提高了22.7%和14.8%.老化前后微塑料对Zn （II）的吸附均符合准二级动力学模型.颗粒内扩散模型表明,Zn （II）在微塑料上的吸附过程可分为快速吸附,慢速吸附和吸附平衡3个阶段.同时,老化前后微塑料对Zn （II）的吸附均符合Langmuir吸附等温线模型.热力学结果表明,微塑料对Zn （II）的吸附是自发的吸热过程.Ca²⁺、腐殖酸和低pH值不利于微塑料对Zn （II）的吸附.     

Rapid decolorization of Acid Orange II aqueous solution by amorphous zero-valent iron

Some problems including low treatment capacity, agglomeration and clogging phenomena, and short working life, limit the application of pre-treatment methods involving zero-valent iron (ZVI). In this article, ZVI was frozen in an amorphous state through a melt-spinning technique, and the decolorization effect of amorphous ZVI on Acid Orange II solution was investigated under varied conditions of experimental variables such as reaction temperature, ribbon dosage, and initial pH. Batch experiments suggested that the decolorization rate was enhanced with the increase of reaction temperature and ribbon dosage, but decreased with increasing initial solution pH. Kinetic analyses indicated that the decolorization process followed a first order exponential kinetic model, and the surface-normalized decolorization rate could reach 2.09 L/(m². min) at room temperature, which was about ten times larger than any previously reported under similar conditions. Recycling experiments also proved that the ribbons could be reused at least four times without obvious decay of decolorization rate and efficiency. This study suggests a tremendous application potential for amorphous ZVI in remediation of groundwater or wastewater contaminated with azo dyes.     

One-step synthesis of Cu(II) metal–organic gel as recyclable material for rapid, efficient and size selective cationic dyes adsorption

Efficient removal of non-biodegradable and hazardous dyes from wastewater remains a hot research topic. Herein, a rationally designed a Cu(Ⅱ)-based metal–organic gel(Cu-MOG) with a nanoporous 3 D network structure prepared via a simple one-step mixing method was successfully employed for the removal of cationic dyes. The Cu-MOG exhibited high efficiency, with an adsorption capacity of up to 650.32 mg/g, and rapid adsorption efficiency, with the ability to adsorb 80% of Neutral Red within 1 min. The high adsorption efficiency was attributed to its large specific surface area, which enabled it to massively bind cationic dyes through electrostatic interaction, and a nanoporous structure that promoted intra-pore diffusion. Remarkably, the Cu-MOG displayed size-selective adsorption, based on adsorption studies concerning dyes of different sizes as calculated by density functional theory. Additionally, the adsorption performance of the Cu-MOG still maintained removal efficiency of 100% after three regeneration cycles. These results suggested that the Cu-MOG could be expected to be a promising and competitive candidate to conveniently process wastewater.     

树脂负载Fe3+/Cu2+多相类芬顿降解染料橙黄

制备了新型多相类Fenton催化剂(Fe3+cu2+)/R(Fe3+和cu2+同时负载于离子交换树脂),以橙黄Ⅳ为研究对象,探讨了初始过氧化氢浓度、橙黄Ⅳ浓度、催化剂量、初始pH值及温度等因素对催化反应速率的影响,并对该催化剂重复使用性能进行测试.研究结果表明,该催化剂(Fe3++Cu2+)/R与Fe3+/R相比表现出更好的催化过氧化氢分解的活性,使橙黄Ⅳ的降解率提高10%;催化过氧化氢氧化橙黄Ⅳ的反应遵循假一级反应动力学,反应活化能为10.71 kJ·mol-1;催化剂表现出良好的重复使用性能,Fe3+和cu2+在树脂表面负载比较牢固,具有较好的稳定性和耐用性.同时,电子顺磁共振(EPR)测试结果表明,cu2+的掺杂能有效地促进OH·的产生;X射线光电子能谱(XPS)测试结果表明,反应过程中存在高价态铁物种.因此,在该体系反应过程中产生的活性物种是OH·和高价态铁同时共存.     

Fe掺杂Bi2MoO6的制备及其可见光催化活化PMS降解橙黄Ⅱ的研究

采用一锅水热合成法制备Fe掺杂Bi2MoO6光催化剂,对Bi2MoO6的主体结构进行修饰和调整.在可见光LED照射下,利用合成的Fe-Bi2MoO6催化剂活化过一硫酸盐(PMS,peroxymonosulfate,oxone)对偶氮染料橙黄Ⅱ进行光催化降解.采用X射线衍射(XRD),扫描电子显微镜(SEM),透射电子显微镜(TEM),X射线能谱(XPS)和紫外-可见漫反射光谱(UV-Vis)对催化剂的形貌微观结构和化学价态进行表征,并应用在光催化活化PMS降解橙黄Ⅱ的过程中.结果表明,催化剂投加量为0.4 g/L,PMS投加量为0.4 mmoL/L,初始pH值接近中性条件下,Fe-Bi2MoO6材料对橙黄Ⅱ的去除率可以达到100％.经过Fe掺杂后,Fe取代一部分的Bi3+,致使主体晶格出现畸变,不仅有利于光生电子和空穴的产生、分离和转移,还增强了 Bi2MoO6的光催化活性.Fe-Bi2MoO6光催化剂经重复使用5次后对橙黄Ⅱ的降解率仍然可以达到89.1％以上,具有优秀的光催化稳定性能.活性自由基的出现在光催化降解过程中起到主要作用,由此展示出一种潜在的光催化降解机制,且Fe掺杂Bi2MoO6比单纯Bi2MoO6具有更好的光催化降解稳定性.