碘化阶层孔氧化硅纳米球对水中典型有机氯污染物的吸附性能研究

采用共缩聚法,成功地原位合成了碘改性的阶层多孔氧化硅纳米球（SiO₂-I）,研究了其基于卤键作用对典型有机氯污染物六六六的吸附性能,并考察了改性剂I-硅烷含量和pH值对吸附效果的影响.实验结果表明,该纳米材料对六六六表现出优异的吸附富集性能,吸附速率快,60 min内对六六六的去除率为71.6%,240 min内达到吸附平衡,去除率可达98.3%,最大吸附量为178.6 mg·g^-1;吸附动力学符合拟二级动力学模型;碘物种的加入提高了阶层多孔氧化硅的吸附速率和吸附效率.另外,为了便于纳米吸附材料的分离,本研究对SiO₂-I纳米球进行了磁性化.研究发现,磁性化修饰后,SiO₂-I纳米材料仍然保留对六六六优异的吸附富集性能,240 min时的吸附去除率达90.3%.     

模拟土壤淋洗废液中重金属的选择性去除与淋洗液的回收研究

土壤淋洗废液中污染物的选择性去除是实现淋洗液回收的关键.本文以硫化钠（Na₂S）、乙基黄原酸钾（PEX）、二甲基二硫代氨基甲酸钠（DTC）作为重金属沉淀剂处理电子垃圾污染土壤模拟淋洗废液,在筛选出Na₂S作为理想重金属沉淀剂的基础上,研究初始pH值、反应温度、沉淀剂浓度等因素对Na₂S分离络合态重金属的影响,并通过软件模拟和产物表征等方式推测反应机理.结果表明：Na₂S对柠檬酸络合态重金属的分离顺序依次为Cu、Pb、Cd,符合硫化物溶度积原则;反应温度、初始pH值对Na₂S处理络合态重金属无显著影响,重金属去除率均保持在90%以上,柠檬酸的回收率约为95%;Visual MINTEQ模拟结果显示,S^2-投加前液相中重金属主要以H₂CA^-、HCA^2-和CA^3-结合形式存在,S^2-投加后液相中重金属则以HS^-和S^2-结合形式存在;扫描电镜及能谱（SEM-EDS）表明,S^2-与金属阳离子按物质的量比1：1生成硫化物沉淀物,沉淀主要呈团聚、成簇和圆片状存在;X射线衍射（XRD）分析结果表明,沉淀产物中存在CuS、CdS、PbS和CuPbS₂.本研究结果可为化学沉淀法处理重金属污染土壤淋洗废液提供技术参考.     

高原高寒污水处理系统的微生物群落特征

为研究高原高寒污水处理系统活性污泥的微生物群落结构及多样性,以拉萨、云南、四川的3座高原污水厂作为实验组,同时以重庆2座非高原污水厂作为对照,采用PCR-DGGE技术对比分析了高原与非高原污水厂的微生物特性.研究表明：高原污水厂样品与非高原样品在聚类中展现出了较为疏远的关系,微生物群落区别明显.受强紫外线辐照的抑制,高原高寒污水处理系统微生物多样性的平均水平显著低于非高原污水厂,较低的微生物多样性是导致高原高寒地区污染物去除效果不佳的一项重要原因.群落构成方面,共鉴定出16个优势菌属,对应Proteobacteria、Bacteroidetes、Firmicutes、Verrucomicrobia 4个门.组间差异分析结果发现,高原组中丰度显著偏高的菌属只有Prosthecobacter,该菌在污水厂内分布广泛,且能够适应高原低温的条件.对于大多数活性污泥微生物而言,高原强紫外线是不利的生存条件.因此,减少高原露天污水处理系统的紫外辐照,是提升污水处理效能的一个潜在措施.     

酸性紫色水稻土颗粒有机质对镉的吸附特性

采集典型的酸性紫色水稻土（APPS）,从中分离出颗粒有机质（POM）,通过批量试验研究POM及其来源土壤Cd²⁺的吸附动力学、等温吸附和热力学特征,通过扫描电镜-能谱仪、傅里叶红外光谱仪等手段及吸附前后镉的形态变化的测定,研究了POM对Cd²⁺的吸附机制.结果表明：POM对Cd²⁺的亲和力远高于其来源土壤.POM及土壤对Cd²⁺的吸附动力学最优模型均为准二级动力学.Langmuir、Freundlich方程均能较好地描述其等温吸附特征,其中对POM,以Freundlich方程更优,表明POM对Cd²⁺的吸附属于多分子层的非均质吸附.吸附热力学参数△G^θ均小于0、△H^θ和△S^θ均大于0,表明吸附属于自发吸热过程.根据△H^θ值及解吸试验判定POM对Cd²⁺的吸附以化学吸附为主,土壤对Cd²⁺的吸附过程以物理吸附为主.吸附平衡后,土壤中可交换态镉比例提高,而POM中交换态和络合态镉比例增加.综上及吸附前后POM的表征结果说明,POM对Cd²⁺的吸附机制包括含氧官能团的络合、离子交换、阳离子-π键、沉淀作用和静电吸附.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Removal and desorption of chromium in synthetic effluent by a mixed culture in a bioreactor with a magnetic field

Two chromium removal experiments were performed in bioreactors with and without a magnetic field under the same conditions.The release of the chromium present in the biomass was tested in two experiments one with the initial pH of the medium and one with pH 4.0.The objective was to remove Cr(Ⅵ) and total Cr from the effluent,this was carried out by placing biological treatments of synthetic effluent contaminated with 100 mg/L of Cr(Ⅵ) in a bioreactor with neodymium magnets that applied a magnetic field(intensity85.4 mT) to the mixed culture.The removal of Cr(Ⅵ) was approximately 100.0% for the bioreactor with a magnetic field and 93,3% for the bioreactor without a magnetic field for9 hr of recirculation of the synthetic effluent by the bioreactor.The removal of total Cr was61.6% and 48.4%,with and without a magnetic field,respectively;for 24 hr.The desorption of Cr(VI) in the synthetic effluent was 0.05 mg/L,which is below the limit established by Brazilian legislation(0.1 mg/L) for the discharge of effluent containing Cr(Ⅵ) into bodies of water.The results obtained for the removal of chromium in synthetic effluent suggested that there was no significant influence on the viable cell count of the mixed culture.The desorption of Cr(Ⅵ) in synthetic effluent after bioadsorption of chromium by the mixed culture in the process of removal of chromium in bioreactors with and without a magnetic field was not significant in either of the experiments with different initial pHs.     

硅胶表面TEOS疏水化改性及吸附VOCs特性

以正硅酸乙酯（TEOS）为疏水改性剂,通过硅胶表面的羟基接枝反应,得到具备一定疏水性的改性硅胶;利用BET、FT-IR、XRD和TG-DTG等手段对改性硅胶的结构及稳定性进行了表征;在此基础上考察了改性硅胶对各类有机废气的吸附性能.结果表明,TEOS成功接枝在了硅胶表面,改性硅胶不仅具备一定的疏水性,而且机械强度增加到原来的66.85%,稳定性也都得到了提高; 550℃空气下焙烧后的改性硅胶仍具有疏水性且吸附容量是焙烧之前的2倍;在高湿度高浓度的废气治理中,TEOS改性硅胶表现出更高的吸附能力和优良的热再生性能.高浓度下改性硅胶的吸附容量是低浓度下的10倍且不受水汽的影响;改性硅胶循环10次的吸附/脱附几乎不变,且在一定条件下,15~30min就达到90%的脱附率.     

磁性有序介孔碳的制备及其对水中双酚A的吸附

采用水热法成功制备了磁性有序介孔碳（Fe-OMC）,用于吸附水中双酚A （BPA）.采用高倍投射电镜、X射线衍射仪、傅里叶红外光谱仪、比表面积分析仪和振动样品磁强计对Fe-OMC进行表征.结果表明,该吸附剂具备较大的比表面积、独特的有序介孔孔道结构、丰富的含氧官能团以及较强的超顺磁性.Fe-OMC能够高效地吸附去除水中的BPA,平衡吸附量可达72.62mg/g,经过外加磁场分离回收后依旧具备较好的吸附性能.随着BPA浓度从1mg/L提高到20mg/L,其平衡吸附量由8.33mg/g增至91.78mg/g.随着pH值的升高呈现出先降低后升高再降低的趋势,最高吸附量出现在pH=8（75.34mg/g）.Fe-OMC对BPA的吸附过程可用准二级吸附动力学模型和Langmuir吸附等温模型进行描述.计算的热力学参数表明,Fe-OMC对BPA的吸附过程是自发进行的放热过程.     

基于铁锰泥的除砷吸附剂性能比较及吸附机理

为解决反冲洗铁锰泥粉末吸附剂（BSPA）使用后难以泥水分离问题,将除铁锰水厂生物滤池产生的反冲洗泥制成颗粒吸附剂（GA）和磁性粉末吸附剂（MPA）,并对BSPA、GA和MPA的除砷性能进行了比较,通过SEM、TED、XRD、BET、FTIR等技术对3种材料进行了表征,寻找3种吸附剂之间除砷性能差异的根源.结果表明,BSPA、GA和MPA对As （V）的最大吸附容量分别为40.980,5.048,8.694mg/g,改性后的吸附材料GA和MPA对砷的吸附能力下降.BSPA是一种以纤铁矿为主的无定形结构混合物,并混有针铁矿和结晶度差的水铁矿,GA的XRD图谱中出现石英晶体和少量赤铁矿晶体的衍射峰,而MPA的主要成分为结晶程度较高的磁赤铁矿.3种材料中均存在有利于吸附的含羟基官能团.BSPA、MPA和GA的比表面积分别为253.150,238.660,43.803m²/g.物相改变且结晶程度增加、表面羟基减少和比表面积降低是导致GA和MPA的砷吸附容量比BSPA低的主要因素.     

Human viral pathogens are pervasive in wastewater treatment center aerosols

Wastewater treatment center(WTC) workers may be vulnerable to diseases caused by viruses, such as the common cold, influenza and gastro-intestinal infections. Although there is a substantial body of literature characterizing the microbial community found in wastewater, only a few studies have characterized the viral component of WTC aerosols,despite the fact that most diseases affecting WTC workers are of viral origin and that some of these viruses are transmitted through the air. In this study, we evaluated in four WTCs the presence of 11 viral pathogens of particular concern in this milieu and used a metagenomic approach to characterize the total viral community in the air of one of those WTCs. The presence of viruses in aerosols in different locations of individual WTCs was evaluated and the results obtained with four commonly used air samplers were compared.We detected four of the eleven viruses tested, including human adenovirus(h Ad V),rotavirus, hepatitis A virus(HAV) and Herpes Simplex virus type 1(HSV1). The results of the metagenomic assay uncovered very few viral RNA sequences in WTC aerosols, however sequences from human DNA viruses were in much greater relative abundance.