膨胀石墨对U(VI)的吸附特性

高温加热可膨胀石墨制得膨胀石墨,用于去除溶液中的U(VI)。通过静态吸附实验,研究了初始pH、吸附剂投加量、U(VI)初始浓度、温度以及吸附时间对膨胀石墨吸附U(VI)效果的影响。实验结果表明,膨胀石墨吸附U(VI)的最佳pH为6.5,在温度为30℃,投加量为2.0 g/L,U(VI)初始质量浓度为10 mg/L时,对U(VI)的去除率达到98.08%,反应在4 h达到平衡。Langmuir等温吸附模型和准二级动力学模型较好地拟合了吸附过程,30℃时饱和吸附量为27.03 mg/g;热力学分析表明,膨胀石墨对U(VI)的吸附是自发的放热反应。比表面积测试、扫描电镜、X射线能谱与傅里叶红外光谱分析结果表明,膨胀石墨对U(VI)的吸附以物理吸附为主,表面官能团起辅助作用。解吸实验证明,膨胀石墨是可重复利用的吸附剂。     

石墨炉原子吸收分光光度法测定固体废物中的钡

研究了石墨炉原子吸收分光光度法测定固体废物中钡的方法。确定了石墨管类型、最佳升温程序和酸消解体系等的测定条件,并通过实际样品检测验证了方法的可行性。结果表明,采用热解涂层石墨管,当溶液钡浓度在0~50.0 μg/L,最佳灰化温度为1 000 ℃,最佳灰化时间为8.0 s,最佳原子化温度为2 600 ℃,最佳原子化时间为2.8 s时,钡浓度与吸光度呈良好的线性关系,相关系数为0.999 1,方法检出限为2.7 mg/kg,相对标准偏差为2.7%~5.4%,实际样品的加标回收率为89.5%~94.5%。     

一种新型石墨电极的制备及其对苯酚的去除

为了探索一种对有机废水处理有效、廉价、来源广泛、环境友好的电极,以石墨、环氧树脂、固化剂和丙酮为原料,研究制备了一种新型石墨电极 (NGE). 分别采用热水浸泡、乙醇溶液回流、丙酮回流、超声-丙酮回流以及电化学法对制备的石墨电极进行预处理,前三者效果较差,超声-丙酮回流可改善处理效果,但不够理想,电化学法可取得满意的效果.苯酚降解的UV光谱分析表明,尽管商品石墨电极 (CGE) 比NGE具有更高的苯酚氧化效率,但其电解液积累大量的苯醌,而NGE电解液中苯醌积累量少,并且电解过程中逐渐降低. NGE比CGE具有更好的TOC去除效果,两者TOC去除率分别为40%和31%. SEM分析结果表明,CGE被严重腐蚀,NGE无明显变化,表现出良好的稳定性.     

Performance and mechanism of Cr(VI) removal by zero-valent iron loaded onto expanded graphite

Zero-valent iron (ZVI) was loaded on expanded graphite (EG) to produce a composite material (EG-ZVI) for efficient removal of hexavalent chromium (Cr(VI)). EG and EG-ZVI were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy and Brunauer–Emmett–Teller (BET) analysis. EG-ZVI had a high specific surface area and contained sub-micron sized particles of zero-valent iron. Batch experiments were employed to evaluate the Cr(VI) removal performance. The results showed that the Cr(VI) removal rate was 98.80% for EG-ZVI, which was higher than that for both EG (10.00%) and ZVI (29.80%). Furthermore, the removal rate of Cr(VI) by EG-ZVI showed little dependence on solution pH within a pH range of 1–9. Even at pH 11, a Cr(VI) removal rate of 62.44% was obtained after reaction for 1 hr. EG-ZVI could enhance the removal of Cr(VI) via chemical reduction and physical adsorption, respectively. X-ray photoelectron spectroscopy (XPS) was used to analyze the mechanisms of Cr(VI) removal, which indicated that the ZVI loaded on the surface was oxidized, and the removed Cr(VI) was immobilized via the formation of Cr(III) hydroxide and Cr(III)–Fe(III) hydroxide/oxyhydroxide on the surface of EG-ZVI.     

石墨炉法测定铅的基体改进剂的选择

通过一系列实验,选择了石墨炉法测定铅的最佳基体改进剂,并确定了使用该基体改进剂的最佳灰化温度和原子化温度。     

巯基硅烷改性氧化石墨对砷的吸附性能

为提高氧化石墨(GO)对砷的吸附能力,以3-巯基丙基三甲氧基硅烷为改性剂,制备了巯基改性的氧化石墨(GO-SH),考察其对水中砷的吸附性能.采用单因素实验法考察了初始pH值、吸附剂投加量、温度等对吸附效果的影响,拟合了吸附等温线,并研究了吸附动力学和吸附热力学规律.实验结果表明,在最优条件下,GO-SH对初始浓度为4 mg.L-1的砷去除率达到97.7%;吸附等温线符合Langmuir和Freundlich模型,45℃时由Langmuir模型得到的饱和吸附量(Qm)为24.45 mg.g-1;吸附动力学符合准二级模型,内扩散模型符合高浓度砷的吸附动力学;热力学研究表明,吸附过程是自发吸热的反应,以化学吸附为主.     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

石墨管连续涂覆结合基体改进测定地表水中的铅

尝试了使用5%钼酸铵-5%磷酸二氢铵溶液组成石墨管连续涂覆结合基体改进剂的方法,应用于地表水Pb的测量中。实验表明,本法具有提高石墨管在使用过程中的稳定性,消除基体效应的作用。     

石墨-活性炭纤维复合电极电吸附处理含盐废水的研究

高盐废水是目前水处理领域的难点,作为一种新型的除盐技术,电吸附技术具有众多优点.本文研究了一种新型碳基复合材料,石墨-活性炭纤维复合电极,并考察了其应用于电吸附的影响因素和除盐效果.在电压为1.6 V,停留时间为60min,极板间距为1 cm时电吸附装置的除盐效果最优.用其分别对精制棉黑液和叶绿素铜钠废水进行了处理.电极对数为8对时对经酸析处理后的精制棉黑液的电导率和COD的去除率分别达到58.8%和75.6%;电极对数为6~8时对叶绿素铜钠生产废水的电导率的去除率能超过50.0%,COD的去除率约为13.5%.     

全自动石墨消解-原子荧光法测定土壤总汞

采用全自动石墨消解-原子荧光光度法对土壤总汞进行测定,确定最佳消解时间为1 h,消解液最佳用量为8.0 m L。方法在总汞质量浓度为0.2~2.0μg/L范围内具有良好的线性,相关系数为0.999 9,当取样量为0.500 0 g时,检出限为0.002 mg/kg;测定不同标准土壤样品总汞的结果均在保证值范围内,精密度为4.0%~7.0%,加标回收率为95.0%~108.5%;对甘肃省实际土壤及沉积物样品测定进一步验证了方法的适用性。该法适合大批量样品分析,对于提高工作效率有重要意义。