浅谈海上油井安全阀及其控制系统技术的应用

针对实际生产条件，为全面推行海上安全环保、节能与清洁生产，在油井上安装了太阳能安全阀控制系统，对油井生产与安全管理起着重要的作用。     

石脑油罐压力安全阀泄漏的隐患治理

石脑油罐压力安全阀泄漏，严重威胁生产与施工的安全进行。通过拆检，弄清了安全阀泄漏的原因，采取了相应措施，彻底解决了这一重大安全隐患。     

反应器引压端法兰焊接阀门断裂原因分析

通过对Z41H-160型阀体端法兰断裂件的宏观检查、化学成分分析、金相分析、断口形貌观察、EDS能谱分析和维氏硬度测试等研究,表明阀体热处理不当致使硬度超高,阀门结构不合理导致硫化物应力腐蚀是阀体断裂的主要原因。     

Comparative study on effect of blending,thermal barrier coating (LHR) and injector nozzle geometry on biodiesel-fuelled engines

Increased petroleum prices, increased threat to the environment from exhaust emissions and global warming have generated intense international interest in developing renewable and alternative non-petroleum fuels for internal combustion engines. Evolving suitable technology for addressing energy crisis creates a continued investigation into the search for sustainable and clean-burning renewable fuels. This work investigates suitability of different non-edible-derived biodiesels such as cotton seed oil methyl ester (COME), Honne oil methyl ester (HnOME) and Rubber seed oil methyl ester (RuOME) to four stroke, single cylinder compression ignition (CI) engine. Engine tests were conducted to study the effect of fuel blending, thermal barrier coating (TBC) or Low Heat Rejection (LHR) and injector nozzle geometry on the performance, combustion and emission characteristics of COME, HnOME and RuOME in the modified CI engine. Blends of biodiesels with diesel were varied from 20 to 80% in steps of 20%. Two thermal barrier coatings of partially stabilized zirconium (PSZ) and aluminium oxide (Al₂O₃) were provided on the engine to make it fully adiabatic. Nozzle injectors of 3, 4 and 5 holes, with size of orifice varied from 0.2 to 0.3 mm size were selected for the study. It was concluded that B20 biodiesel blend, PSZ-coated engine and four hole nozzle injector of 0.2 mm size resulted in overall better engine performance with increased brake thermal efficiency (BTE) and reduced HC, CO, smoke emissions for the fuel combinations tested. Combustion analysis to study the effect of biodiesel blends, LHR coatings, injector nozzle geometry on the performance of the biodiesel-fuelled engine has been presented to give more insight into the behaviour of operation.     

注入式低温等离子体技术用于卷烟厂异味处理的效果研究

将注入式低温等离子体技术应用于烟厂制丝排潮和制丝除尘排放气体异味处理中,研究了注入式低温等离子体发生器参数对臭味浓度、非甲烷总烃和可检出典型有机物去除率的影响规律。结果表明:注入式低温等离子体发生器工作电压越高,注入处理烟道的氧化活性物种浓度越高,注入量越大,臭味浓度、非甲烷总烃和可检出典型有机物去除率也越高。选取合理的工作电压,臭味浓度去除率可达90%以上,非甲烷总烃去除率分别达到了83.8%(制丝排潮)和78.1%(制丝除尘)。     

电磁阀贮存寿命加速试验技术研究

首先陈述了贮存寿命加速试验的基本原理,介绍电磁阀的结构组成,分析了失效模式和失效机理后,采取恒定应力加速试验方法,然后运用极大似然估计和最小二乘法对数据进行处理,最后得出其贮存寿命等结论。     

汽车气制动ABS调节阀测试系统气动测试回路设计研究

针对气制动防抱死制动系统(ABS)调节阀测试系统气动回路设计进行研究;根据我国的汽车生产和检测现状,在确定气动测试回路总体方案的基础上,进行主控部分、负载回路、控制回路的设计和计算,所设计的气路检测系统可用于测试8种典型的气制动元件的密封性及动静态特性,通过不同的组合能够满足每一种阀的测试需求。该气动测试回路有效解决了简单阀类测量方法的不足,满足不了生产率及测量精度要求的问题。     

并联式双梯度反相离子对液相色谱法快速检测土壤中芳磺酸

通过阀切换并联式双系统,建立了一套测定土壤样品中7种芳磺酸的反相离子对液相色谱法。该方法采用2根色谱柱,一根色谱柱分析的同时,另一根色谱柱通过阀切换实现平衡,节约了38.5%的分析时间。方法使用Dikma Diamonsil C18(150 mm×4.6 mm×5μm)色谱柱,以离子对试剂(四丁基硫酸氢铵)和乙腈为流动相,检测波长为226、235、258 nm。各组分线性关系良好,线性相关系数均在0.999 9以上。随机抽取样品进行重新提取、检测,得到各组分的相对标准偏差均小于7%,且定量限最高不超过0.181 2μg/g,重复性和定量限均能满足实验要求。     

A new approach to determine relieving temperature and thermodynamic behavior of trapped single and multi-phase fluid exposed to fire

Process safety plays a key role in modern industries. This is more significant specifically in off-shore oil and gas platforms where releasing hydrocarbons could cause irreversible damages to both environment and personnel. An important instrument device which can provide safety for process equipment in oil and gas fields is safety relief valve. Correct sizing procedure of such devices depends strongly on physical properties of fluid and relieving condition. The present study revolved around applying thermodynamic concepts and modeling to throw some light on the behavior of trapped fluid exposed to fire in order to evaluate precise temperature and fluid properties at relieving condition. Peng–Robinson equation of state together with a three phase flash has been utilized to handle the calculation. Effect of different design parameters has been evaluated for three distinct categories of fluids namely natural gas, gas-condensate mixture, and gas-oil mixtures. These parameters encompass of operating temperature, operating pressure, Difference of Operating and Design Pressure, gas and oil specific gravities, gas-oil ratio, and water cut. The study depicted that American Petroleum Institute practice number 521 which suggests an ideal gas assumption fails to provide reliable predictions as it significantly overestimate the relieving temperature. Moreover, black oil correlations were also used for the relief temperature estimation of gas-oil-water mixtures. Comparison with HYSYS results as a prominent engineering software proved that black oil models are reliable tools to predict relief temperature.     

Dynamic behaviour of direct spring loaded pressure relief valves in gas service: II reduced order modelling

A previous study of gas-service direct-spring pressure relief valves connected to a tank via a straight pipe is continued by deriving a reduced-order model for predicting oscillatory instabilities such as valve flutter and chatter. The reduction process uses collocation to take into account a finite number N of acoustic pressure waves within the pipe, resulting in a set of 2N+3 ordinary differential equations. Following a novel non-dimensionalization, it is shown analytically that the model can exhibit, at experimentally realistic parameter values, instabilities associated with coupling between the valve and acoustic waves in the pipe. The thresholds for each instability are such that for a given flow rate, the first mode to go unstable as the inlet pipe length increases is the quarter-wave mode, then a three-quarter wave, a 5/4-wave etc. Thus the primary mode of instability should always be due to the quarter wave. In the limit of low flow rates, a simple approximate expression is found for the quarter-wave instability threshold in the form of inlet pipe length against mass flow rate. This threshold curve is found to agree well with simulation of the full model. For higher flow rates there is a need to include fluid convection, inlet pressure loss and pipe friction in order to get good agreement. The reduced model enables the dependence of the stability curve on key dimensionless physical parameters to be readily computed.