可张孔曝气器曝气能耗试验研究

通过试验研究，总结出可张孔曝气阻力损失的影响因素，以优化产品的结构设计参数，降低产品在工程应用中的能耗，获取更好的经济效益。     

裂解温度和离子强度对不同来源生物炭胶体释放行为的影响

近年来环境中生物炭胶体形成受到广泛关注,它是生物炭在环境中物理分解作用的重要过程,对污染物迁移有着重要影响.然而,目前对生物炭胶体释放过程和影响因素的研究甚少,人们对生物炭胶体释放机理的认识还很有限.本研究以小麦秸秆和花生壳为生物质来源,系统地探讨了生物炭的裂解温度（300~700 ℃）和溶液离子强度（0.1~10 mmol·L^-1）对生物炭胶体产率的影响.结果表明,随着裂解温度的升高,生物炭的耐磨性增强,且在较高的裂解温度下（≥500 ℃）花生壳生物炭的耐磨性显著强于小麦秸秆生物炭.生物炭的胶体产率受到生物质来源和裂解温度的显著影响,花生壳生物炭的胶体产率低于小麦秸秆生物炭,高温裂解（≥600 ℃）生物炭的胶体产率显著低于中低温裂解生物炭.在相同溶液离子强度下,生物炭胶体产率与其亚微米级碎片率呈显著正相关（p<0.05）,即生物炭中亚微米级碎片率越高,生物炭胶体产率越高.当溶液离子强度从1 mmol·L^-1增加到10 mmol·L^-1时,两种来源生物炭的胶体产率均显著降低,其降低的程度因生物炭裂解温度而异,其中低温裂解（300 ℃）生物炭的胶体产率降低了11.1%~11.2%,中高温裂解（≥ 500 ℃）生物炭的胶体产率降低了60.0%~97.2%.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

基于边介数的省域生态廊道构建方法优化

我国城市建设和生态保护工作均对土地资源有大量需求,二者之间的矛盾在经济优先发展区表现尤为明显.为了有效地改善生态环境,管控土地利用并引导其变化发展,需要建设具备不可替代特征的省域生态廊道.最小累积阻力模型（minimum cumulative resistance,MCR）是识别生态廊道最常用、有效的模型,但在应用于省域尺度时,MCR模型识别的潜在廊道路由存在冗余的问题.因此,通过引入网络科学中的边介数指数（edge-betweenness）对MCR模型进行优化,计算潜在廊道路由的边介数指数值,选取出其中最为重要和简明的结构来连通生态源地,即提取潜在路由中的骨干路由（backbone route）和关键战略点（key strategic point）作为不可替代的结构来指导省域生态廊道建设.将优化后的MCR模型应用于广东省,构建了全长5 493 km的省域生态廊道,其中包含生态源地20处,关键战略点11个,骨干生态廊道29条.骨干路由与关键战略点构成的不可替代省域生态廊道（irreplaceable provincial corridor）能够实现"廊道数量和占地面积最少、连通性基本不变"的目标.研究显示,边介数能够对潜在路由进行优化筛选,识别出维护省域生态安全的关键结构;不可替代生态廊道能够指导省域生态规划和土地空间的发展利用,并为更高水平的生态安全环境提供了演进的基础;同时也为土地资源紧张的地区提供了建设生态廊道的参考与依据.      

我国燃煤电厂大气汞控制技术综合评估与对策探讨

采用模糊综合评价法与层次分析法或专家判定法相结合,对我国燃煤电厂非常规污染物大气汞控制技术进行了综合评估,以筛选出最佳控制技术.建立了环境、经济和技术为一级指标的三层指标体系,共22个评价指标;初步筛选出洗选煤+烟气净化协同脱除技术、烟气净化协同脱除技术、烟气净化协同脱除技术+活性炭吸附技术等七项技术及技术组合并对其开展评估.结果表明:强调环境因素的层次分析法综合评估结果表明,超低排放协同脱除技术+活性炭吸附技术得分最高（0.797 0）,为最佳控制技术.而专家判定法与强调经济因素的层次分析法的综合评估结果一致,洗选煤+烟气净化协同脱除技术最具经济优势,是专家认可的最佳可用技术（BAT）和最佳环境实践（BEP）.研究显示,我国现阶段可采用洗选煤+超低排放协同脱除技术对燃煤电厂的大气汞污染进行控制,但为达到发达国家的严格排放标准,必须采用超低排放协同脱除技术+活性炭吸附技术.      

芳纶纤维对飞机尾翼结构抗鸟撞性能影响研究

目的研究飞机尾翼结构采用芳纶纤维复合材料的抗鸟撞性能。方法根据芳纶纤维夹芯和芳纶纤维层合板两种飞机尾翼前缘构型,分别建立有限元模型进行仿真计算,分析两种构型鸟撞后的损伤和变形,并对两种构型进行抗鸟撞性能研究试验。结果芳纶夹芯前缘构型前缘凹陷,前梁没有破裂;芳纶层合板前缘构型前缘破裂,前梁有破损。试验结果与仿真分析结果高度吻合。结论芳纶夹芯前缘构型比芳纶层合板前缘构型具有更好的抗鸟撞性能。芳纶纤维层合板构型会造成前缘蒙皮变形过大,前梁腹板破损,导致飞机鸟撞后维修成本较高。     

四环素胁迫对Shigella flexneri细菌四环素抗性基因抗性表达的影响过程

四环素(TC)抗生素在不同环境介质中已被广泛检出,为研究其对四环素抗性基因(TC-ARGs)丰度变化及表达水平的影响过程,以从活性污泥中筛选和纯化分离获得的弗氏志贺氏菌(Shigella flexneri)为研究对象,考察了不同浓度TC对其生长过程的作用影响,采用荧光定量PCR和逆转录PCR方法定量检测了不同抗性机制TC-ARGs,包括tetC、tetO和tetX基因的丰度变化及表达水平,并探讨了TC浓度与TC-ARGs丰度及其表达水平之间的相关关系.结果表明,在培养周期内(24 h),TC胁迫对Shigella flexneri细菌的生长具有抑制作用,细菌细胞浓度增长速率随TC暴露浓度的升高而降低,但对TC-ARGs丰度变化影响较小.TC胁迫能够促进Shigella flexneri细菌TC-ARGs的转录表达,tetC、tetO和tetX基因表达水平在整个培养周期内均先升高后降低.由相关性分析可知,TC浓度与TC-ARGs丰度及其表达水平之间相关关系不显著,但tetC和tetO基因丰度与其转录表达水平之间存在显著的正相关关系,表明其基因丰度一定程度上可用来衡量和评价其抗性表达水平.     

喷丸强化技术在某型作动筒延寿修理中的应用

目的将某型作动筒的寿命由6000±150起落延长至12 000±150起落。方法采用喷丸强化技术对作动筒的主要承力零件进行喷丸强化处理,提高零件的抗疲劳和抗应力腐蚀性能。通过疲劳寿命试验验证对比喷丸强化处理前后典型零件和作动筒的寿命指标是否达到了预期目标。结果喷丸强化处理前的3件前耳环螺栓试验循环次数均未超过1.8×10~6即断裂,喷丸强化后达到3.6×10~6时仍未断裂。喷丸强化处理后的4件主耳环螺栓与喷丸强化处理前对比,断裂时的试验循环次数均有不同程度的提高,均值寿命比值大于2.36。喷丸强化处理前后的主前作动筒疲劳寿命试验达到预期的循环次数时,均没有出现断裂或者损坏。结论喷丸强化处理能有明显提高作动筒的抗疲劳和抗应力腐蚀性,强化处理后的零件疲劳寿命能够超过处理前的2倍,可以采用喷丸强化技术延长作动筒的使用寿命。     

Large-scale mercury variations in Lake Vänern (Sweden) 1974-98

Lake V?nern, the largest lake in Sweden, has been seriously contaminated with mercury during the 20th century. In the 1970's and 80's the direct load, mainly from a chlor-alkali industry in the area, of mercury was drastically reduced as a response to new legislation, from three to five tons down to between five and ten kg yr(-1). Large amounts of the disposed pollutant have accumulated in the sediments. The question posed in this work is now, is the effect of the drastic load reduction after more than two decades visible in the sediments? The question is relevant as large areas still are blacklisted for fishing, but also as a follow-up of a major remedy action. The lake also serves as a freshwater reservoir for even Sweden's second largest city. This work synthesises and compares data of mercury in the sediments from three major field programs, in 1974, 1984 and 1998. The interest is focused on both spatial heterogeneity and temporal trends. In 1974, the surface concentrations are significantly higher than in subsequent surveys. Significant differences are also found between 1984 and 1998. Significant spatial differences within the lake are found for respective year. The most contaminated area is located in the north, close to the major point source (a former chlor-alkali industry). This is also the area with the largest improvement, as a direct response to the reduction in load. Further from the outlet, the recovery is more affected by burial and transport processes out into the deeper basins.     

Exposure Assessment to Mercury Vapor in Chloralkali Industry

The aim of the study was to develop a sampling method aimed at individual sampling of mercury vapor and subsequent individualexposure assessment of the worker. Hopcalite available fromInowrocawskie Zakady Chemiczne (in Poland) was founduseful for mercury vapor sampling in active and passive individual samplers. However the sampling rate determined forpassive sampler in steady-state laboratory chamber cannot be usedunder fluctuating conditions of mercury vapor concentration andair movement typical for field measurement. In order to check comparativeness of passive and active sampling methods, sampleswere taken in the same time and individual samplers fixed toworker's clothes were used. Mercury vapor concentration wasmeasured at two chloralkali industries in Poland and the resultswere presented. Excessive exposure in both industries wasconfirmed by finding elevated mercury concentration in urinesamples from the workers.