某型飞机外翼5—8肋损伤原因分析及修复探讨

目的 分析某型飞机外翼5—8肋油箱区结构不同程度损伤的原因,制定修复方案。方法采用受载分析、有限元仿真计算、静力试验数据分析等强度计算方法分析损伤产生的原因,采用扫描电子显微镜和光学显微镜对磨痕形貌进行观测等失效分析,对损伤结构件开展失效模式分析,根据损伤原因及失效模式制定科学简便的修复方案,同时对损伤长桁采取的修补措施进行强度校核。结果 通过对外翼油箱充压破坏理论分析、有限元仿真计算、静力试验数据反推,并结合飞机实际损伤情况,得出油箱破坏理论分析危险薄弱部位与真实破坏情况一致的结论。有限元仿真计算最危险结构部位与实际结构首先发生破坏部位吻合,可作为深入制定修复方案及推测实际加载压力的依据。通过静力试验数据反推、结构实际损伤及有限元仿真计算结论得出,外翼5—8肋结构出现损伤时油箱施加压力约0.5 MPa,针对损伤制定了更换外翼油箱内部第5—8肋损伤结构和贴补加强损伤长桁的修理方案,经结构强度校核,满足设计要求。结论 分析认为外翼5—8肋油箱区结构损伤原因为油箱压力超过设计值导致结构过载断裂,采用贴补加强修理损伤长桁和更换第5—8肋损伤结构的修复方案能够满足强度设计要求,可指导同类飞机类似结构损伤故障的原因分析和修理,提醒同类飞机维修人员在飞机维护时应关注外翼油箱压力超压问题。     

Injuries in Full-Scale Vehicle Side Impact Moving Deformable Barrier and Pole Tests Using Postmortem Human Subjects

Objective: To conduct near-side moving deformable barrier (MDB) and pole tests with postmortem human subjects (PMHS) in full-scale modern vehicles, document and score injuries, and examine the potential for angled chest loading in these tests to serve as a data set for dummy biofidelity evaluations and computational modeling.

Methods: Two PMHS (outboard left front and rear seat occupants) for MDB and one PMHS (outboard left front seat occupant) for pole tests were used. Both tests used sedan-type vehicles from same manufacturer with side airbags. Pretest x-ray and computed tomography (CT) images were obtained. Three-point belt-restrained surrogates were positioned in respective outboard seats. Accelerometers were secured to T1, T6, and T12 spines; sternum and pelvis; seat tracks; floor; center of gravity; and MDB. Load cells were used on the pole. Biomechanical data were gathered at 20 kHz. Outboard and inboard high-speed cameras were used for kinematics. X-rays and CT images were taken and autopsy was done following the test. The Abbreviated Injury Scale (AIS) 2005 scoring scheme was used to score injuries.

Results: MDB test: male (front seat) and female (rear seat) PMHS occupant demographics: 52 and 57 years, 177 and 166 cm stature, 78 and 65 kg total body mass. Demographics of the PMHS occupant in the pole test: male, 26 years, 179 cm stature, and 84 kg total body mass. Front seat PMHS in MDB test: 6 near-side rib fractures (AIS = 3): 160–265 mm vertically from suprasternal notch and 40–80 mm circumferentially from center of sternum. Left rear seat PMHS responded with multiple bilateral rib fractures: 9 on the near side and 5 on the contralateral side (AIS = 3). One rib fractured twice. On the near and contralateral sides, fractures were 30–210 and 20–105 mm vertically from the suprasternal notch and 90–200 and 55–135 mm circumferentially from the center of sternum. A fracture of the left intertrochanteric crest occurred (AIS = 3). Pole test PMHS had one near-side third rib fracture. Thoracic accelerations of the 2 occupants were different in the MDB test. Though both occupants sustained positive and negative x-accelerations to the sternum, peak magnitudes and relative changes were greater for the rear than the front seat occupant. Magnitudes of the thoracic and sternum accelerations were lower in the pole test.

Conclusions: This is the first study to use PMHS occupants in MDB and pole tests in the same recent model year vehicles with side airbag and head curtain restraints. Injuries to the unilateral thorax for the front seat PMHS in contrast to the bilateral thorax and hip for the rear seat occupant in the MDB test indicate the effects of impact on the seating location and restraint system. Posterolateral locations of fractures to the front seat PMHS are attributed to constrained kinematics of occupant interaction with torso side airbag restraint system. Angled loading to the rear seat occupant from coupled sagittal and coronal accelerations of the sternum representing anterior thorax loading contributed to bilateral fractures. Inward bending initiated by the distal femur complex resulting in adduction of ipsilateral lower extremity resulted in intertrochanteric fracture to the rear seat occupant. These results serve as a data set for evaluating the biofidelity of the WorldSID and federalized side impact dummies and assist in validating human body computational models, which are increasingly used in crashworthiness studies.     

转轴弯曲模的设计

设计了一种防止回弹和提高制件刚性的转轴弯曲模,阐述了其模具结构及工作过程。     

某型飞机机翼下壁板整体油箱端5肋结构选型疲劳寿命研究

目的研究某型飞机机翼下壁板整体油箱端5肋结构的选型疲劳寿命。方法在结构选型设计时初步确定长桁连续和长桁断开两种结构形式的基础上,采用静力试验与疲劳试验方法对这两种结构模拟件进行对比试验验证。结果两种结构模拟件的静破坏载荷分别为588.20 k N和587.97 k N,与设计预计破坏载荷(590k N)高度一致。在相同的等幅载荷谱下,长桁连续结构的中值疲劳寿命和95%置信度与95%可靠度下的疲劳寿命分别约为长桁断开结构的1.7倍和4倍。长桁连续结构的疲劳分散性明显小于长桁断开结构。长桁连续结构的疲劳断口主要呈现脆性穿晶疲劳断裂特征;而长桁断开疲劳断口则呈现出韧窝型断裂和解理断裂的混合型穿晶疲劳断裂特征。疲劳断口微观形貌表明,长桁断开结构在疲劳过程中产生了塑性变形,这就从微观机理上解释了长桁连续结构的疲劳性能优于长桁断开结构的原因。结论在结构质量相近的情况下,长桁连续结构明显优于长桁断开结构。     

PBL剪力键破坏形态及极限承载力试验研究

根据已有试验结果,总结了有贯穿钢筋类PBL剪力键(perfobond rib shear connector)的3种破坏形态,其中充分发挥承载力的破坏形态为贯穿钢筋剪切破坏。为了研究PBL剪力键的极限承载力,对4组21个试件进行了静载破坏试验,结合文献[10]的试验结果,研究了各种因素对PBL剪力键极限承载力的影响,提出了有贯穿钢筋类PBL剪力键极限承载力计算公式。结果表明:有贯穿钢筋类PBL剪力键的极限承载力主要与贯穿钢筋面积及强度有关,与混凝土强度、混凝土榫面积无关,横向钢筋面积及强度对其的影响较以前试验所得结果小。     

复合内嵌筋材加固混凝土梁破坏模式分析

对螺旋肋钢筋施加预应力,将其与碳纤维筋组合后,以不同的方式嵌入到混凝土梁受拉区混凝土保护层中,对混凝土梁进行加固,能显著提高混凝土梁的承载能力。在对承载能力试验结果做简单阐述的前提下,针对加固梁中多材料、多界面存在的客观现实,全面系统地分析了加固梁可能存在的破坏模式,且与试验梁的破坏模式进行对比,对不同加固方式加固的试验梁的破坏模式及破坏机理进行了分析。分析表明,多界面的存在严重影响了加固梁的承载力;不同的破坏界面,应对加固材料断面总内力采取不同的取值,在试验中应特别注意破坏界面的判别,否则计算结果会产生很大误差。     

Real-World Rib Fracture Patterns in Frontal Crashes in Different Restraint Conditions

Objective: The purpose of this study was to use the detailed medical injury information in the Crash Injury Research and Engineering Network (CIREN) to evaluate patterns of rib fractures in real-world crash occupants in both belted and unbelted restraint conditions. Fracture patterns binned into rib regional levels were examined to determine normative trends associated with belt use and other possible contributing factors.

Methods: Front row adult occupants with Abbreviated Injury Scale (AIS) 3+ rib fractures, in frontal crashes with a deployed frontal airbag, were selected from the CIREN database. The circumferential location of each rib fracture (with respect to the sternum) was documented using a previously published method (Ritchie et al. 2006) and digital computed tomography scans. Fracture patterns for different crash and occupant parameters (restraint use, involved physical component, occupant kinematics, crash principal direction of force, and occupant age) were compared qualitatively and quantitatively.

Results: There were 158 belted and 44 unbelted occupants included in this study. For belted occupants, fractures were mainly located near the path of the shoulder belt, with the majority of fractures occurring on the inboard (with respect to the vehicle) side of the thorax. For unbelted occupants, fractures were approximately symmetric and distributed across both sides of the thorax. There were negligible differences in fracture patterns between occupants with frontal (0°) and near side (330° to 350° for drivers; 10° to 30° for passengers) crash principal directions of force but substantial differences between groups when occupant kinematics (and contacts within the vehicle) were considered. Age also affected fracture pattern, with fractures tending to occur more anteriorly in older occupants and more laterally in younger occupants (both belted and unbelted).

Conclusions: Results of this study confirmed with real-world data that rib fracture patterns in unbelted occupants were more distributed and symmetric across the thorax compared to belted occupants in crashes with a deployed frontal airbag. Other factors, such as occupant kinematics and occupant age, also produced differing patterns of fractures. Normative data on rib fracture patterns in real-world occupants can contribute to understanding injury mechanisms and the role of different causation factors, which can ultimately help prevent fractures and improve vehicle safety.     

大采高仰斜工作面玻璃纤维增强塑料锚杆煤壁加固技术及应用

针对段王矿090502综采工作面存在近200m仰采段,为提高煤壁稳定性,避免或减少煤壁片帮发生,提出玻璃纤维增强塑料锚杆煤壁加固方案,通过数值模拟方法对煤壁加固参数进行了优化研究,并进行了现场应用.研究结果表明:采用φ20mm×3.0m全螺纹玻璃纤维增强塑料锚杆、间排距为1.5m×1m进行煤壁加固,不仅可保持煤壁稳定,而且施工方便,保证了工作面的正常回采.     

低碳经济下煤气化产业发展的新动力

煤炭在我国能源结构中占有着举足轻重的地位,我国的低碳经济发展模式必须在高碳经济结构下去探寻。只有从我国实际出发,立足于煤炭,大力发展新型煤气化技术,进一步拓宽其应用范围,通过政府的积极引导和支持创新国有新型煤气化技术,走出一条适合我国国情的低碳经济发展与环保之路。