金属表面涂装行业VOCs排放特征及排放系数

对比了浙江省2014和2018年金属表面涂装企业的有机废气排放及治理情况,分析了该行业涂料及稀释剂的使用、主要污染因子,测算了溶剂型、水性涂料的挥发性有机物（VOCs）产生系数和排放系数.结果表明：2018年VOCs治理水平明显高于2014年,水性涂料使用企业比例由18%上升至36%,纯溶剂型企业由82%下降至64%;金属表面涂装行业的主要排放污染物为二甲苯、丁醇、乙酸乙酯、乙酸丁酯、甲苯、丙二醇、乙苯、苯乙烯等8种有机物.溶剂型和水性涂料的VOCs产生系数分别为0.72和0.31kg/kg;溶剂型和水性涂料2014年VOCs排放系数为0.64和0.29kg/kg,2018年为0.48和0.21kg/kg.     

模拟土壤淋洗废液中重金属的选择性去除与淋洗液的回收研究

土壤淋洗废液中污染物的选择性去除是实现淋洗液回收的关键.本文以硫化钠（Na₂S）、乙基黄原酸钾（PEX）、二甲基二硫代氨基甲酸钠（DTC）作为重金属沉淀剂处理电子垃圾污染土壤模拟淋洗废液,在筛选出Na₂S作为理想重金属沉淀剂的基础上,研究初始pH值、反应温度、沉淀剂浓度等因素对Na₂S分离络合态重金属的影响,并通过软件模拟和产物表征等方式推测反应机理.结果表明：Na₂S对柠檬酸络合态重金属的分离顺序依次为Cu、Pb、Cd,符合硫化物溶度积原则;反应温度、初始pH值对Na₂S处理络合态重金属无显著影响,重金属去除率均保持在90%以上,柠檬酸的回收率约为95%;Visual MINTEQ模拟结果显示,S^2-投加前液相中重金属主要以H₂CA^-、HCA^2-和CA^3-结合形式存在,S^2-投加后液相中重金属则以HS^-和S^2-结合形式存在;扫描电镜及能谱（SEM-EDS）表明,S^2-与金属阳离子按物质的量比1：1生成硫化物沉淀物,沉淀主要呈团聚、成簇和圆片状存在;X射线衍射（XRD）分析结果表明,沉淀产物中存在CuS、CdS、PbS和CuPbS₂.本研究结果可为化学沉淀法处理重金属污染土壤淋洗废液提供技术参考.     

高原高寒污水处理系统的微生物群落特征

为研究高原高寒污水处理系统活性污泥的微生物群落结构及多样性,以拉萨、云南、四川的3座高原污水厂作为实验组,同时以重庆2座非高原污水厂作为对照,采用PCR-DGGE技术对比分析了高原与非高原污水厂的微生物特性.研究表明：高原污水厂样品与非高原样品在聚类中展现出了较为疏远的关系,微生物群落区别明显.受强紫外线辐照的抑制,高原高寒污水处理系统微生物多样性的平均水平显著低于非高原污水厂,较低的微生物多样性是导致高原高寒地区污染物去除效果不佳的一项重要原因.群落构成方面,共鉴定出16个优势菌属,对应Proteobacteria、Bacteroidetes、Firmicutes、Verrucomicrobia 4个门.组间差异分析结果发现,高原组中丰度显著偏高的菌属只有Prosthecobacter,该菌在污水厂内分布广泛,且能够适应高原低温的条件.对于大多数活性污泥微生物而言,高原强紫外线是不利的生存条件.因此,减少高原露天污水处理系统的紫外辐照,是提升污水处理效能的一个潜在措施.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Removal and desorption of chromium in synthetic effluent by a mixed culture in a bioreactor with a magnetic field

Two chromium removal experiments were performed in bioreactors with and without a magnetic field under the same conditions.The release of the chromium present in the biomass was tested in two experiments one with the initial pH of the medium and one with pH 4.0.The objective was to remove Cr(Ⅵ) and total Cr from the effluent,this was carried out by placing biological treatments of synthetic effluent contaminated with 100 mg/L of Cr(Ⅵ) in a bioreactor with neodymium magnets that applied a magnetic field(intensity85.4 mT) to the mixed culture.The removal of Cr(Ⅵ) was approximately 100.0% for the bioreactor with a magnetic field and 93,3% for the bioreactor without a magnetic field for9 hr of recirculation of the synthetic effluent by the bioreactor.The removal of total Cr was61.6% and 48.4%,with and without a magnetic field,respectively;for 24 hr.The desorption of Cr(VI) in the synthetic effluent was 0.05 mg/L,which is below the limit established by Brazilian legislation(0.1 mg/L) for the discharge of effluent containing Cr(Ⅵ) into bodies of water.The results obtained for the removal of chromium in synthetic effluent suggested that there was no significant influence on the viable cell count of the mixed culture.The desorption of Cr(Ⅵ) in synthetic effluent after bioadsorption of chromium by the mixed culture in the process of removal of chromium in bioreactors with and without a magnetic field was not significant in either of the experiments with different initial pHs.     

特殊区域地表水环境背景值表征技术方法研究与应用

选取黑龙江省源头水保护区作为研究对象,根据DEM数据对保护区内随机布设的水质监测点控制单元进行划分并提取单元内的相关指标建立监测点背景特性量化模型,基于量化结果提出地表水环境背景值监测方案,建立背景值数据库.选取研究区自然属性指标与空间属性指标,以空间叠置技术与聚类分析方法对研究区地表水进行背景值分区,最终将黑龙江省分为六大地表水水质背景值地理分区,并计算了各分区地表水环境背景值表征范围.表征范围显示：依据现行标准进行水质评价,保护区内水质背景值已超出Ⅱ类水质标准限值.因此,基于水质背景值研究成果提出了考虑背景值影响下的水环境质量评价方法,并将方法应用于研究区,结果表明方法切实可行且优于单因子评价法.研究成果可为区域制定背景值影响下的水环境评价方法提供科学的数据支撑与理论依据.     

纤维增强气凝胶复合材料高温结构转变及热稳定性研究

目的研究高温受热条件下纳米复合隔热材料的结构转变特征及热稳定性。方法采用扫描电镜、X射线衍射仪、红外光谱仪及热重仪等检测方法。结果纤维增强气凝胶材料从室温到650℃存在连续的质量损失,从室温到放热前,质量损失为1.66%;365℃开始出现放热,温度升至398℃时达到峰值,整个放热过程对应质量损失约为1.3%;从435℃放热结束开始到650℃的质量损失为1.46%。经过400℃热处理后,试样比表面积从268m~2/g增加到437m~2/g;当试样热处理温度达到600℃时,试样的比表面积明显随之降低至198m~2/g。结论 SiO_2气凝胶复合材料以无定形结构为主,存在少量的二氧化钛晶体。在400℃左右,SiO_2气凝胶结构中硅甲基Si—CH_3发生氧化,产生明显的放热峰,之后硅羟基Si—OH之间发生缩聚反应,使600℃热处理后气凝胶中Si—O—Si网络骨架强度有所提高。未处理的纤维增强气凝胶材料试样上气凝胶纳米颗粒构成的块体较为良好地包裹在玻璃纤维表面,而经过600℃的高温热处理1 h后,块体气凝胶脱离了光滑的纤维表面,气凝胶纳米粒子发生收缩,致使材料比表面积下降。     

海州湾表层沉积物磷的吸附容量及潜在释放风险

利用磷吸附指数（PSI）、磷吸附饱和度（DPS）和磷释放风险指数（ERI）研究了2016年10月和2017年5月海州湾表层沉积物的磷吸附容量及潜在释放风险.结果显示,2016年秋季PSI变化范围为99.58~199.39[mgP/（100g）]/[μmol/L],DPS变化范围为23.118%~34.289%;2017年夏季PSI变化范围是130.29~198.57[mgP/（100g）]/[μmol/L],DPS变化范围为25.545%~42.135%,两次调查中PSI和DPS均表现出相反的平面分布趋势.PSI和Al_ox、Fe_ox呈显著正相关,说明Fe_ox和Al_ox是影响海州湾表层沉积物吸附磷的主要因素,且Fe_ox占主导作用;DPS与Al_ox和Fe_ox分别表现出了显著负相关性和极显著负相关性,说明Al_ox和Fe_ox含量的增大会降低表层沉积物的磷吸附饱和度.2016年10月磷释放风险指数（ERI）的变化范围为11.59%~34.18%,2017年5月磷释放风险指数（ERI）的变化范围为12.86%~32.34%,从2次调查结果整体来看,海州湾表层沉积物的磷释放风险为中度风险.     

Human viral pathogens are pervasive in wastewater treatment center aerosols

Wastewater treatment center(WTC) workers may be vulnerable to diseases caused by viruses, such as the common cold, influenza and gastro-intestinal infections. Although there is a substantial body of literature characterizing the microbial community found in wastewater, only a few studies have characterized the viral component of WTC aerosols,despite the fact that most diseases affecting WTC workers are of viral origin and that some of these viruses are transmitted through the air. In this study, we evaluated in four WTCs the presence of 11 viral pathogens of particular concern in this milieu and used a metagenomic approach to characterize the total viral community in the air of one of those WTCs. The presence of viruses in aerosols in different locations of individual WTCs was evaluated and the results obtained with four commonly used air samplers were compared.We detected four of the eleven viruses tested, including human adenovirus(h Ad V),rotavirus, hepatitis A virus(HAV) and Herpes Simplex virus type 1(HSV1). The results of the metagenomic assay uncovered very few viral RNA sequences in WTC aerosols, however sequences from human DNA viruses were in much greater relative abundance.     

Relationship between physicochemical properties and dewaterability of hydrothermal sludge derived from different source

Sewage sludge (SS) and deinking sludge (DS) were used to comparatively study the hydrothermal dewatering of sludge with different components. For a better overview, an insight into the relationship between physicochemical properties and dewaterability of hydrothermal sludge was provided. Results found that not all kinds of sludge were suitably conditioned by hydrothermal treatment (HT) in term of the elevation of dewaterability. Higher hydrothermal temperature tended to enhance the dewaterability of SS rather than DS, which was supported by the variation of their physicochemical properties (including water distribution, bonding energy, extracellular polymeric substance (EPS), particles size, acid functional groups and zeta potential in this study). In addition, the changes in surface morphology suggested that the reverse effect of HT on sludge dewaterability was mainly due to their dewatering behavior. For SS, the destruction of EPS structure leaded to the release of bound water, thereby strengthening sludge dewatering. Conversely, “Bridging effect” generated by lignocellulose in DS was beneficial for sludge dewatering; however, the increasing hydrothermal temperature degraded part of lignocellulose and weakened “bridging effect”, finally resulting in worse dewaterability of DS.