Treatability studies of naphthalene in soil,water and air with persulfate activated by iron(Ⅱ)

Chemical oxidation was applied to an artificially contaminated soil with naphthalene (NAP). Evaluation of NAP distribution and mass reduction in soil, water and air phases was carried out through mass balance. Evaluation of NAP distribution and mass reduction in soil, water and air phases was carried out through mass balance. The importance of the air phase analysis was emphasized by demonstrating how NAP behaves in a sealed system over a 4 hr reaction period. Design of Experiments method was applied to the following variables: sodium persulfate concentration [SP], ferrous sulfate concentration [FeSO₄], and pH. The system operated with a prefixed solid to liquid ratio of 1:2. The following conditions resulted in optimum NAP removal [SP] = 18.37 g/L, [FeSO₄] = 4.25 g/L and pH = 3.00. At the end of the 4 hr reaction, 62% of NAP was degraded. In the soil phase, the chemical oxidation reduced the NAP concentration thus achieving levels which comply with Brazilian and USA environmental legislations. Besides the NAP partitioning view, the monitoring of each phase allowed the variabilities assessment over the process, refining the knowledge of mass reduction. Based on NAP distribution in the system, this study demonstrates the importance of evaluating the presence of semi-volatile and volatile organic compounds in the air phase during remediation, so that there is greater control of the system as to the distribution and presence of the contaminant in the environment. The results highlight the importance of treating the contaminant in all its phases at the contaminated site.     

Preparation of solar-enhanced AlZnO@carbon nano-substrates for remediation of textile wastewaters

Photoactive aluminum doped ZnO(AlZnO) was synthesized by sol-gel method.After that,AlZnO photocatalyst was deposited on five carbon-based materials(CBMs) using ultrasonic route followed by solid-state mixing using ball mill.The CBMs used were poly aniline(PANI),carbon nitride(CN),carbon nanotubes(CNT),graphene(G),and carbon nanofibers(CNF).The crystal phases,elemental compositions,morphological,and optical properties of the AlZnO@CBMs composites were investigated.Experimental results revealed that two of AlZnO@CBMs composites exhibited superior bleaching efficiency(100% removal) and photocatalytic stability(three cycles) for 50 μmol/L Methylene Blue(MB) contaminated water after 60 min irradiation in visible light at pH 6.5,0.7% H_2O_2,and 5 g/L inorganic salts.Under optimum conditions,AlZnO@CBMs nanocomposites were employed for the treatment of mixed dyestuffs composed of MB,Methyl Orange(MO),Astrazone Blue FRR(BB 69),and Rhodamine B(RhB) dyes under dark,ultraviolet,visible,and direct sunlight.For mixed dyestuffs,the AlZnO@G achieved the highest dye sorption capacity(60.91 μmol dye stuffs/g) with kinetic rate 8.22 × 10~(-3) min~(-1) in 90 min via multi-layer physisorption(Freundlich isotherm) on graphene sheet.In additions,AlZnO@CN offered the highest photo-kinetic rate(K_(photo)) of～54.1 × 10~(-3) min~(-1)(93.8% after 60 min) under direct sunlight.Furthermore,the selective radical trapping experiment confirmed that the holes and oxidative superoxide radicals are crucial on dyes photodegradation pathway.Owing to their superior performance,AlZnO@G and AlZnO@CN nanocomposites can offer an effective in-situ solar-assisted adsorption/photocatalytic remediation of textile wastewater effluents.     

底泥原位洗脱过程中氮磷含量与形态变化特征

随着城市化进程的不断推进,城市河流底泥中内源氮磷污染问题日益突出.为研究原位洗脱技术对污染底泥中氮、磷物质和成分的作用效果,以北京市凉水河作为研究对象,分别比较了现场试验洗脱与对照组0~30 cm分层底泥以及实验室模拟洗脱处理前后0~10 cm底泥中pH、E_h（氧化还原电位）、容重、含水率、OM（有机质）、TN、TP和氮、磷形态分布的变化特征.结果表明:①现场洗脱对0~5 cm厚度底泥的处理和模拟洗脱处理均对底泥中pH、E_h、含水率的改变以及其中TN、TP的去除效果表现显著,其中,现场试验洗脱组0~5 cm范围底泥中w（TN）、w（TP）分别较对照组降低了66.4%±17.4%、40.8%±24.4%,模拟洗脱处理对底泥中OM、TN、TP的去除率分别达70.1%±4.8%、66.8%±2.0%、43.1%±3.1%.②原位洗脱技术对底泥中TN的去除主要通过对PON（颗粒态有机氮）的去除来实现,现场和模拟试验过程中PON对TN去除的贡献率分别达55.0%和73.6%.③原位洗脱对底泥中TP的去除主要通过对Al-P（铝结合态磷）、OP（有机磷）的去除来实现,现场和模拟试验中Al-P、OP对TP去除的贡献率分别达37.0%、66.2%和31.3%、43.7%.研究显示,原位洗脱技术可有效去除城市河流底泥处理层中的氮磷物质,并以有机氮、磷物质的去除为主.      

土壤调理剂对土壤-水稻系统Cd、Zn迁移累积的影响及健康风险评价

选取湖南省长沙市北山镇某中重度Cd污染稻田,研究了土壤调理剂(石灰石+偏高岭土+钙镁磷肥)对稻田土壤重金属Cd、Zn的钝化效果,以及对水稻各部位累积Cd和Zn的影响,并进行了Cd的健康风险评价.结果表明,使用土壤调理剂提高了稻田土壤p H值.Cd的CaCl_2提取态含量降低了0.9%~24.1%,Zn的CaCl_2提取态含量降低了22.5%~69.6%.土壤调理剂显著降低了水稻糙米中Cd与Zn的含量,与对照相比分别降低了10.8%~47.3%、10.3%~17.5%;土壤调理剂对水稻糙米Cd的吸收和累积的影响要远大于Zn,水稻糙米中的Cd/Zn比随着土壤调理剂施用量的增加而显著降低.研究区大米重金属Cd目标危害系数THQ值大于1,说明当地人群通过食用大米途径摄入重金属Cd存在健康风险.土壤调理剂有效地抑制了水稻植株对土壤中Cd的吸收,并降低了Cd/Zn比,使糙米中的Cd含量显著降低,从而降低了当地人群通过食用大米途径摄入重金属Cd的健康风险.     

非饱和带强化反应层脱氮的试验研究

自然堆肥过程中,畜禽养殖产生的粪污渗滤液入渗土壤非饱和带.高浓度有机氮在微生物作用下经由复杂的地球化学过程转化为各种含氮物质,其中硝酸盐迁移能力较强,在降雨条件下入渗地下水,造成区域性地下水硝酸盐污染.在非饱和带中构建由木屑和壤土组成的强化反应层,通过间歇性的原位淋溶脱氮试验,系统地研究了非饱和带含水量及COD、硝态氮、亚硝态氮和氨氮的浓度变化规律,评价了强化反应层的脱氮能力.研究结果表明:①反应层中木屑材料的强吸水特性使得灌水后短时间内反应层含水量大幅提升,形成有利于反硝化进行的厌氧环境.木屑通过水解作用释放大量溶解性有机碳,供给反硝化微生物进行脱氮.②在入渗硝态氮浓度为170.00 mg·L~(-1)条件下,反应层对硝态氮去除率最高可达97.63%.反应层脱氮量随处理水量增加而提升,当上层为砂土时脱氮量最高,可达24.61 g·m~(-3).③反应层中的NO~-_3-N发生了完全反硝化,出水中NO~-_2-N浓度低于0.5 mg·L~(-1),几乎不发生积累.同时,反应层中发生的DNRA过程使氨氮浓度小幅升高.强化脱氮反应层可阻控硝酸盐污染地下水.     

表面活性剂增强修复地下水中PCE的砂箱实验及模拟

在石英砂充填的二维砂箱中开展表面活性剂（Tween 80）冲洗四氯乙烯（PCE）的修复实验,基于图像分析技术监测不同污染源区结构条件下NAPL相的去除过程.由于实验条件限制,实验中缺乏溶解相浓度数据.为此进一步基于UTCHEM数值模拟方法来理解NAPL相和溶解态之间的质量传输过程,并探讨表面活性剂浓度、注入速率等因素对修复效率的影响.综合砂箱实验和数值模拟结果表明：介质均质和非均质条件下会形成不同类型DNAPL污染源区结构,表现为离散状PCE与池状PCE体积比（GTP）差异.由于离散状污染物与表面活性剂的接触面积更大,更易被优先去除;初始GTP值越高,污染物的修复速率和修复效率也越高.增大表面活性剂浓度或提高表面活性剂的注入速率,虽然能提高DNAPL的修复速率,但会明显降低表面活性剂的修复效率,实验过程中修复效率降幅可达93%.线性驱动溶解模型可以有效地模拟表面活性剂修复DNAPLs过程,基于数值模拟方法选择合适的表面活性剂配比可有效的节省实际污染场址修复经费和时间成本.     

亚甲蓝分光光度法测定饮用水中阴离子表面活性剂的方法讨论

用10ml氯仿萃取离子缔合物一次,洗涤一次,不稀释。它与国标方法的线性回归无显著性差异,此方案测定样品的准确度En为0·34,小于1,结果令人满意,测量不确定度是除国标方法外最低的方案。因此它具有低污染、操作简单的特点,并可用于常规检测饮用水中的LAS。     

土壤对六价铬的还原容量初步研究

提出并讨论了土壤的潜在还原容量、有效还原容量和条件还原容量等概念，通过对采用北京和唐山地下水饮用水源区３个包气带土壤样品的土柱淋滤实验，研究了土壤对水溶液中六价铬的还原作用，研究了上述土壤各种还原容量之间的关系及影响因素，探讨了向土壤中投加适量常见，无毒，价廉的还原性物质以提高土壤还原能力的方法和将其应用于去除灌溉用污染地下水中六价铬的可能性，实验结果表明，在正常环境条件下，土壤的有效还原容量比土     

VOC removal from contaminated groundwater through membrane pervaporation. (Ⅱ): 1,1,1-trichloroethane-SDS surfactant solution system

IntroductionTheconventionalmethodforsubsurfaceremediationofgroundwatercontaminationwithVOCsistheso called“pump and treat”technology .Thelimitationofthisapproachistheprohibitivelylongtreatmenttimeforremediatingthegroundwatercontaminatedwithcommonchlorinatedsolventsthathavedensitiesgreaterthanthatofwater(classifiedasDNAPLs densenon aqueousphaseliquids) .Thisislargelyduetotheverylowwatersolubilityandlowbiodegradabilityofthisclassofsolventsandthetendencyofthesolventssettlinginthebottomofanaqu…     

Electrochemical study of sulfide solution in the presence of surfactants

Voltammetric curve studies on aqueous Na2S solution in the presence of three types of surfactants are presented. Presence of anodic surfactant (HTAB) in creases anode current density and makes the corresponding anode peak potential shift to more negative. Potentials of the reduction of elemental sulfur to intermediates Sx2-shift to more negative with the increasing of HTAB concentrations. In the presence of HTAB, the anode current density at 77oC increases more than at 34oC. The electrolysis indicates that anodic product sulfur loosely adhered to the graphite electrode surface when HTAB is added to the anolyte. The total efficiency of producing sulfur is high after several times of cycle electrolysis.The results show that anode passivation is minimized in the presence of HTAB. The depassivation effect of HTAB is discussed.