喷丸强化技术在某型作动筒延寿修理中的应用

目的将某型作动筒的寿命由6000±150起落延长至12 000±150起落。方法采用喷丸强化技术对作动筒的主要承力零件进行喷丸强化处理,提高零件的抗疲劳和抗应力腐蚀性能。通过疲劳寿命试验验证对比喷丸强化处理前后典型零件和作动筒的寿命指标是否达到了预期目标。结果喷丸强化处理前的3件前耳环螺栓试验循环次数均未超过1.8×10~6即断裂,喷丸强化后达到3.6×10~6时仍未断裂。喷丸强化处理后的4件主耳环螺栓与喷丸强化处理前对比,断裂时的试验循环次数均有不同程度的提高,均值寿命比值大于2.36。喷丸强化处理前后的主前作动筒疲劳寿命试验达到预期的循环次数时,均没有出现断裂或者损坏。结论喷丸强化处理能有明显提高作动筒的抗疲劳和抗应力腐蚀性,强化处理后的零件疲劳寿命能够超过处理前的2倍,可以采用喷丸强化技术延长作动筒的使用寿命。     

高温条件下高速碰撞试验技术研究

目的建立高温条件下结构的高速碰撞试验技术。方法基于理论和试验方法,研究影响试样加热/保温、碰靶速度和姿态的关键因素,利用次口径发射技术和电炉技术实现试样的加热、保温和加速。采用间接方法测试试样碰靶时的温度,联合应用次口径发射技术和靶体,控制试样的碰靶姿态,并利用高速摄影技术对其进行测试。通过薄壁圆柱筒的高温高速碰靶验证高温试验技术的有效性。结果建立了加热、加速和姿态控制一体化的高温高速碰撞试验技术,获得了不同尺寸薄壁圆柱筒不同姿态碰靶时的高温冲击动力学响应。正碰时,撞击端镦粗,尾端收缩,尾端的凹陷大于碰撞端的变形;侧碰时,圆筒呈马鞍状;角碰时的变形为楔形。随着圆筒的强度和刚度的降低,圆筒的变形增加,整体发生坍塌,出现大量的皱褶。结论建立的试验技术切实有效,可以用于高温条件下结构高速碰撞效应的研究。     

Modeling photocatalytic destruction of the organic contaminants in continuous stir flow reactor

Thin-film technique is becoming an industry standard for the preparation of TiO₂-based photocatalyst for organic destruction. The catalyst provides several advantages over the conventional powder TiO₂ in the treatment of wastewater and groundwater. In this study, a continuous stir flow reactor model is developed capable of describing the photocatalytic process. The model incorporates the following fundamental mechanisms: adsorption, diffusion, liquid-film transfer, UV attenuation, and photocatalytic reaction. All of the simulation results indicate that there exists a highly nonlinear relation between each of these parameters and the destruction rate. Various incident light intensities also are incorporated to simulate the energy efficiency. The simulations illustrate that the photocatalytic model can be used to elucidate the effect of process variables. It is also possible to “custom-design” a catalyst for the treatment of a particular waste stream.     

熔池高度对双辊薄带凝固组织影响的模拟预测

在已建立的理论数学模型的基础上,以1Cr18Ni9Ti不锈钢为研究对象,模拟预测了薄带厚度保持不变条件下熔池高度对薄带凝固组织的影响。研究结果表明:随着熔池高度增加,1Cr18Ni9Ti不锈钢双辊薄带凝固组织中柱状晶区比例首先增大,然后又逐渐减小。而柱状枝晶取向度和枝晶间距则随着熔池高度的增加而增大,但在较低的熔池高度条件下,柱状枝晶间距在凝固结束时有突然增大的趋势。     

利用DGT高分辨率研究沉积物孔隙水中重金属的浓度和释放通量

2006年5月采集了大辽河河段3个柱状沉积物,测定了沉积物的理化性质和重金属元素的含量,并利用常规离心方法和DGT方法测定了柱状沉积物孔隙水中重金属元素的含量.研究发现沉积物中Cd、Co、Cr和Cu元素含量高低的顺序依次是Cr>Cu>Co>Cd.用DGT方法测定的孔隙水中Cd、Co、Cr和Cu的浓度比用离心方法测定的浓度要低.DGT测定的孔隙水中Cd、Co、Cr和Cu的浓度c_DGT与离心方法测定的孔隙水浓度c的平均比值R分别为0.389、0.328、0.863和0.403,这说明沉积物中这几种金属从固相到液相的再补给速率大小遵循如下规律：Cr>Cu>Cd>Co.沉积物中Cd、Co、Cr和Cu元素的释放通量分别为1.12×１０^{-7～3.28×10-7　nmol/(cm2·s)、2.48×１０-7～10.40×10-7　nmol/(cm2·s)、8.80×１０-6～12.65×10-6 nmol/(cm2·s)和6.14×１０-6～13.93×10-6　nmol/(cm2·s).相关分析结果表明,Cd和Cu元素的迁移转化主要受有机质影响;而Cr元素的迁移转化除了受有机质影响外,还受铁锰氧化物影响比较显著;而Co元素可能受氧化还原电位影响较大.}     

Fabrication and photoelectrocatalytic properties of nanocrystalline monoclinic BiVO4 thin-film electrode

Monoclinic bismuth vanadate(BiVO4) thin film was fabricated on indium-tin oxide glass from an amorphous heteronuclear complex via dip-coating.After annealation at 400,500,and 600°C,the thin films were characterized by X-ray diffraction,field emission scanning electron microscopy,X-ray photoelectron spectroscopy,and UV-Vis spectrophotometry.The BiVO4 particles on the ITO glass surface had a monoclinic structure.The UV-Visible diffuse reflection spectra showed the BiVO4 thin film had photoabsorption propertie...     

考虑岩石抗拉强度受围压影响的地层破裂压模型

预测地层破裂压力是地下流体注入工程中的关键问题,关系到工程的稳定性和安全性。根据地测资料,岩石的抗拉强度会随着围压产生变化,然而目前常见的地层破裂压预测模型均未考虑该因素。基于厚壁圆筒法,针对2种砂岩开展不同围压条件下的砂岩致裂试验,根据试验数据,计算各组试验中试样的抗拉强度,并拟合围压与岩石抗拉强度的关系函数。研究岩石抗拉强度随围压变化的规律,提出能在实际地层中表征该规律的参数,基于该参数对现有的地层破裂压模型进行修正,并结合实测数据验证修正模型的可靠性。研究结果表明:岩石的抗拉强度随着围压的增加呈现明显的线性正相关关系,低围压下,新模型的预测结果与实测数据较为接近。随着围压增加,二者的差异逐渐增大,说明选取的特征参数在低围压下能较好地描述抗拉强度受围压的影响效应,而高围压下参数的取值需进一步研究。     

基于数字信息化的消防呼吸气瓶检验管理系统研究与开发

为解决碳纤维缠绕式消防呼吸气瓶检验中因单机作业而存在的检验效率低、检验质量差、受人为因素影响的问题,研究开发基于数字信息化的碳纤维缠绕式消防呼吸气瓶检验管理系统,该检验系统包括消防呼吸气瓶数据库、OA系统、呼吸气瓶检验软件和手机APP。利用二维码技术和计算机网络,实现呼吸气瓶数据库、检验软件、OA约检和报告审核审批系统、手机APP的数据传输。结果表明:该检验管理系统实现了呼吸气瓶检验的无纸化、过程的可追溯性、检验结果的防伪性等功能,其对于碳纤维缠绕式消防呼吸气瓶检验具有较强的适用性和可行性。     

Diffusive gradients in thin films using molecularly imprinted polymer binding gels for in situ measurements of antibiotics in urban wastewaters

• Selective molecularly imprinted polymer (MIP) binding gel was prepared. • MIP-DGT showed excellent uptake performance for antibiotics. • In situ measurement of antibiotics in wastewaters via MIP-DGT was developed. • The MIP-DGT method was robust, reliable, and highly sensitive. Urban wastewater is one of main sources for the introduction of antibiotics into the environment. Monitoring the concentrations of antibiotics in wastewater is necessary for estimating the amount of antibiotics discharged into the environment through urban wastewater treatment systems. In this study, we report a novel diffusive gradient in thin films (DGT) method based on molecularly imprinted polymers (MIPs) for in situ measurement of two typical antibiotics, fluoroquinolones (FQs) and sulfonamides (SAs) in urban wastewater. MIPs show specific adsorption toward their templates and their structural analogs, resulting in the selective uptake of the two target antibiotics during MIP-DGT deployment. The uptake performance of the MIP-DGTs was evaluated in the laboratory and was relatively independent of solution pH (4.0–9.0), ionic strength (1–750 mmol/L), and dissolved organic matter (DOM, 0–20 mg/L). MIP-DGT samplers were tested in the effluent of an urban wastewater treatment plant for field trials, where three SA (sulfamethoxazole, sulfapyridine, and trimethoprim) and one FQ (ofloxacin) antibiotics were detected, with concentrations ranging from 25.50 to 117.58 ng/L, which are consistent with the results measured by grab sampling. The total removal efficiency of the antibiotics was 80.1% by the treatment plant. This study demonstrates that MIP-DGT is an effective tool for in situ monitoring of trace antibiotics in complex urban wastewaters.     

Fe3+掺杂TiO2薄膜的制备及光催化降解甲醛的研究

采用溶胶-凝胶法制备Fe3+掺杂的TiO2薄膜光催化剂,进行甲醛的光催化实验,考察Fe3+掺杂量、薄膜焙烧温度及溶胶体系pH值对光催化性能的影响。结果表明,Fe3+掺杂量为1.0%,焙烧温度500℃1h,加硝酸溶胶体系pH=4时,Fe3+掺杂TiO2薄膜光催化活性最高。