水泥负载TiO2光催化降解染料水溶液的研究

研究了以ＴｉＯ２为催化剂，且将ＴｉＯ２涂布在模拟工业水处理浅池的水泥质池底表面，以直管高压汞灯为光源，对有机染料酸性玫瑰红Ｂ和晒化绿Ｂ进行光催化降解的可行性。结果表明，在实验条件下，本系统对以上染料有显著的光降解作用，浓度为２５ｍｇ／Ｌ的上述二种染料溶液，经３０ｍｉｎ光照，其降解率分别达８８．２％，此外，还探讨了染料浓度，染料体积、染料溶液ＰＨ值等因素对光降解的影响。     

固定化酵母菌对活性艳蓝KN-R的脱色研究

采用海藻酸钙加活性碳的方法对酵母菌进行固定化。正交试验结果表明，三者合适配比为海藻酸钠3％，活性碳10％，氯化钙4％。此方法制得的凝胶颗粒机械强度好、经久耐用。固定化酵母菌凝胶小球最适条件为：培养时间为48h，培养温度为37℃，培养基pH为3．0，凝胶量为10g。固定化细胞经多次脱色后能重复使用，4次脱色后其脱色率还达79．2％。     

车用三效催化剂的研究进展

三效催化剂是机外治理机动车尾气污染最常采用的有效方法，车用三效催化剂已发展到第4代。目前车用三效催化剂的研究主要集中在：开发稀燃型三效催化剂和紧耦合三效催化剂及发展三效催化剂低温冷起燃技术等。国内应以稀土添加少量贵金属的三效催化剂为主要研究方向，开发适合我国现状的车用净化催化剂技术。     

负载型纳米TiO2光催化剂的制备及其降解水中微量间二甲苯的研究

采用浸涂-烧结法制备的纳米TiO2光催化剂负载量约为6mg／g载体，催化剂经5次重复使用其催化效果稳定，表明催化剂表面TiO2粉体负载牢固；以高压汞灯为光源，对水中微量间二甲苯的负载型纳米TiO2光催化氧化过程的研究表明：初始浓度在6．68～17．36mg／L的范围内，间二甲苯的光催化反应遵循表现一级反应动力学规律，反应的表现速率常数随溶液初始浓度的增大而减小，半衰期则随初始浓度的增大而增加。     

固定化真菌漆酶对分散兰-2BLN的脱色和降解

采用改良壳聚糖固定化的真菌漆酶对染料分散兰-2BLN进行脱色和降解条件的研究,探索了固定化漆酶活力、处理时间、染料浓度、温度和pH对其降解效果的影响。结果表明,固定化漆酶脱色降解分散兰-2BLN的适宜条件为：固定化漆酶活力18.2U／mL,染料浓度100mg／L,温度40℃,pH4.6,在上述条件下降解1.5h,分散兰-2BLN脱色率能达到87.68％。重复分批使用固定化漆酶处理2BLN兰,在使用6批次后,脱色率仍能保持在55％以上,其催化效率得到了较大提高。     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

碳包覆Pd/Al2O3催化剂催化4-溴苯酚加氢脱溴的活性和稳定性调控研究

在污染物液相催化加氢脱卤过程中,提高催化剂的稳定性至关重要.以水热合成法制备了不同碳包覆量的Pd/Al₂O₃@C催化剂,对催化剂进行了系列表征,并将催化剂应用于4-溴苯酚(4-BP)污染物的催化加氢脱溴反应.表征结果显示碳层提高了Pd/Al₂O₃的表面疏水性,有利于4-BP在催化剂上的吸附.并且在Pd/Al₂O₃@C催化剂的碳化过程中,碳还原部分Pd颗粒,并保留部分正价态Pd活性位,增强了4-BP中C-Br键的活化.与Pd/Al₂O₃相比,碳涂层提高了催化剂的催化活性.但当碳包覆量超过最佳包覆量后,暴露的Pd粒子随碳包覆量的增加而减少,导致活性下降.此外,碳层修饰后,催化剂的稳定性显著提高,从而大大抑制了Pd粒子的团聚和损耗.Pd/Al₂O₃@C表面的碳涂层对卤素具有较高的耐受性,从而减轻了液相催化加氢脱卤反应中活性中心的中毒.     

Microbial fuel cells: Advances in electrode modifications for improvement of system performance

There is an increasing trend to conduct the researches related to Microbial Fuel Cells (MFCs) in the recent years. Limited power output has been the major obstacle for the practical application and upscaling of MFCs. Attempts have been made on electrode modifications such as anode treatments, cathode modifications with catalysts and bio cathodes developments to produce varying degrees of improved output current depending upon the types of modifications. Power density and Coulombic efficiency have been considered as the important parameters to analyze the system performances. This paper overviews on the advances made in MFCs’ researches focusing on different types of electrodes modifications along with the involved methodology. Furthermore, the system performances of different modified MFCs are compared in terms of the power density and the Coulombic efficiency.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni(NO3)2和Fe(NO3)3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO+NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

铁炭复配修复地下水中NO_3~--N的条件研究

采用了铁炭复配修复地下水中NO3--N,探讨了实验条件对修复效果的影响。结果表明,在pH值近中性条件(初始pH 6.42)下,反应时间为1 h时NO3--N修复率达到60.85%;Fe/C=1∶1时介质最佳用量分别为4~5 g;Fe/C=1/1.5时修复率为72.80%;反应速率在高振荡强度下大于低振荡强度;氧化铜的催化效果最好,可使修复率提高7.5个百分点。铁炭复配介质修复地下水中NO3--N是有效可行的,修复率随反应时间的增加而提高,在Fe/C=1∶1时修复率与介质用量呈正相关,无限减小Fe/C比并不能无限提高修复率,振荡强度对修复具有显著影响,低振荡强度下的修复过程较高强度存在滞后现象,并非所有金属氧化物催化剂对铁炭修复NO3--N均有促进作用。