Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

乳化液防腐净化机理与装置的试验研究

研究了磁化与充氧在乳化液防腐净化中的作用，设计制作出小型移动式乳化液防腐净化装置，在实验室内，对乳化液连续循环处理五个多月，结果是乳化液仍然保持原始性能，没有腐败变臭迹象，效果理想。     

微孔膜生物反应器在港口含油洗涤废水处理工程中的应用

介绍了微孔膜生物反应器在港口含油洗涤废水处理工程中的应用，进行了设计参数的选取、工程设计和运行效果分析，设计污水处理量为30.0m^3/d。运行结果表明，微孔膜生物反应器具有运行效果稳定、抗冲击负荷能力强、硝化能力强、操作运行简便等优点。     

用水基表面活性剂乳液回收废白土中蜡的界面张力研究

通过测定液体与废白土粉末之间的接触角及液体与蜡之间的液液界面张力，对水基表面活性剂乳液的溶剂及配方进行了优选，得到最佳的水基面活性剂乳液的组成为：质量分数０．２％的十二烷基苯磺酸钠＋体积分数为２．５％的乙醇＋体积分数为２５％的混合烃（正己烷＋苯，等体积）＋体积分数为７２．５％的水。实验证明，用该水基表面活性剂乳液处理废白土，蜡的回收率可达８０％，同时不破坏白土的颗粒结构。     

电凝聚处理轧制乳化废水的研究

用电凝聚法处理轧制乳化废水,探讨了影响破乳的各种因素,确定了最佳处理条件。研究结果表明:该法处理轧制乳化废水的效果很好,浊度去除率可达99.6%,COD去除率达99.5%。此外,还发现电凝聚法的处理效果优于药剂絮凝法。     

聚醚砜超滤膜接枝聚乙烯醇-氨基酸共聚物的亲水改性研究

基于聚合多巴胺的附着性及易与氨基(—NH2)等基团形成共价键的特性,本实验将聚合多巴胺作为对聚醚砜(PES)超滤膜进行表面改性的接枝中间物,将聚乙烯醇(PVA)-氨基酸共聚物接枝至PES膜表面,从而提高PES超滤膜的亲水性能.实验通过PVA与氨基酸的酯化反应形成PVA-氨基酸共聚物,将带有—NH2的共聚物与PES超滤膜表面的聚合多巴胺涂覆层形成共价键,从而将亲水的PVA-氨基酸共聚物接枝到疏水的超滤膜表面.实验利用通量的变化、红外光谱(FTIR)分析、表面接触角、场发射扫描电镜(FESEM)等手段来表征膜特征参数的变化,同时也考察了改性膜对油水乳化液的分离效率和抗污染能力.试验结果表明,经过PVA-氨基酸共聚物接枝改性的膜表面的亲水性有一定的提高,原膜接触角为91°,涂覆和接枝改性后的膜表面接触角分别为71°和53°,油水乳化液的分离实验显示,改性后的膜通量和清洗恢复率均有明显提高.     

氧化还原体系低温引发丙烯酸酯乳液聚合安全风险研究

以甲基丙烯酸甲酯、丙烯酸酯乙酯、丙烯酸酯丁酯为反应单体,十二烷基苯磺酸钠为乳化剂,过硫酸铵为氧化剂,亚硫酸氢钠为还原剂,在低温下进行乳液聚合。主要研究了反应单体的热稳定性及反应过程中的相关热力学参数,最后按照规定对该聚合体系进行了安全风险研究。研究结果表明,丙烯酸酯混合单体无热分解放热风险,丙烯酸酯乳液体系的绝热温升(△Tad)为49.6℃,失控体系能达到的最高温度(MTSR)为91.9℃,该体系的最终反应工艺危险度评估为1级,聚合工艺热风险低。     

Characteristics of stable biodiesel emulsion fuel with the aid of lipophilic surfactant,polyglycerol polyricinoleate (PGPR)

ABSTRACT

Biodiesel emulsion fuel is reported as one of the most feasible options capable of generating lower NOx emission than that from fossil fuels. However, oil and water in the emulsion fuel are easily separated and unstable. The aim of the present study is to consider the production and stability of biodiesel emulsion fuel by using tetraglycerin ester (CR-310), i.e., one of lipophilic surfactant, polyglycerol polyricinoleate (PGPR) and biodiesel, i.e., Waste cooking Oil Methyl Ester (WOME) produced based on waste cooking oil. The corresponding heat rate, water content, and viscosity are measured. Emphasis is placed on the effects of water content and surfactant on biodiesel emulsions. It is found that: (i) stable emulsion fuel is obtained by adding at least 2.0% of CR-310 and is maintained over 1 month, (ii) there is no effect of water content on stable emulsion fuel if CR-310 is used over 2.0%, and (iii) the viscosity of emulsion fuels is higher than that of the biodiesel fuel and is gradually increased with an increase in the water content.     

吸附—电化学法组合工艺处理废乳化液

以季铵盐改性硅藻土为吸油剂,采用吸附—电化学组合工艺处理拉丝废乳化液,优化了工艺条件。实验结果表明,在乳化液pH为5.0、吸油剂加入量为20 g/L、反应温度为25 ℃的最优条件下吸附除油15 min,然后在清液pH为8.5、阳极电流密度为4 A/dm²的最优条件下电化学反应4 h后,废水无色无味,COD为43 mg/L,ρ（NH₃-N）=0,ρ（Cu）= 1.6 mg/L,ρ（Zn）= 3.7 mg/L,浊度为1.1 NTU,达到GB 8978—1996污水综合排放标准。     

O／W型乳化液的处理

采用药剂破乳－电解破乳工艺处理Ｏ／Ｗ型乳化液，药剂破乳选用聚合硫酸铁为破乳剂，破乳时最佳ＰＨ为８，聚合硫酸铁的最佳投量为１５００ｍｇ／Ｌ，电解破乳选用铁作阳极，铝作阴极，电流密度０．８６Ａ／ｄｍ＾２，极距２５ｍｍ，电解时间３ｈ。在上述条件下，破乳效果良好，出水清澈透明，ＣＯＤ总去除率可达到９６－９７％。