包装废弃物添加脱氯半焦制备SRF的热解及动力学特性

利用热重红外分析仪(TG-FTIR)对包装废弃物添加了4种不同比例脱氯半焦制备而成的固体衍生燃料(SRF)的热解特性及热反应动力学进行了研究分析.研究发现,4种燃料热解过程主要包括4个阶段,其中300~400℃和400~500℃为两个主要失重阶段.前一阶段,SRF-1失重显著高于SRF-2、SRF-3和SRF-4,而后一阶段失重分别呈2、3、4倍增加.4种燃料热解残余量的顺序为SRF-4SRF-3SRF-2SRF-1,即添加了脱氯半焦的燃料热解程度越高.FTIR分析表明,添加了脱氯半焦的SRF燃料第三失重峰处不产生氯代烃.随脱氯半焦添加量的增加,第二失重峰CO2产生的浓度减少;第三失重峰CH4析出浓度增加;第四失重峰CO2析出的浓度增加.采用DEAM分布活化能法得到,转化率α0.3时,SRF-2和SRF-3的活化能均高于SRF-1的活化能,0.3α0.9时(α为0.6时除外),SRF-2、SRF-3和SRF-4 3种燃料的活化能低于SRF-1,且SRF-1的活化能呈升高的趋势,而其他3种燃料呈相反趋势.脱氯半焦的添加有利于SRF燃料的热解.     

硬木地板材料和棉花秆的变氧浓度热解燃烧表观动力学的实验研究

本文采用TG-FTIR分析方法深入研究了火场中硬木地板材料和棉花秆变氧浓度燃烧过程,深入分析了氧浓度对纤维物质燃烧表观热失重影响;通过大量的动力学参数计算得出了可燃物的表观活化能与实际氧浓度成线性关系;分析了氧浓度对木材燃烧气体产物的影响,并探索了氧浓度影响热解和燃烧的机理。     

Pyrolysis behaviors of oil sludge based on TG/FTIR and PY-GC/MS

Pyrolysis is an alternative technology for oil sludge treatment. Thermogravimetric Analysis-Fourier Transform Infrared Spectroscopy and Pyrolysis-Gas Chromatography/Mass Spectrometry were employed to investigate the pyrolysis process and products of oil sludge. The pyrolysis process was divided into five stages: drying and gas desorption, oil volatilization, main pyrolysis, semi-coke charring, and mineral decomposition. The main reaction temperatures ranged from 497.6 K to 753.2 K. The products were mainly composed of pairs of alkane and alkene (carbon number ranges from 1 to 27). The mechanisms consisted of random chain scission followed by end chain scission at high temperatures with volatilization occurring during the whole process. This study is useful not only for the proper design of a pyrolysis system, but also for improving the utilization of liquid oil products.     

Study on HCl removal for medical waste pyrolysis and combustion using a TG-FTIR analyzer

Under both pyrolysis and combustion condition, HCl removal efficiency for medical waste with Ca-based additives was semi-quantitatively studied by means of TG-FTIR. Additionally, the difference of HCl removal efficiency for PVC and medical waste was compared. Experimental results showed that: 1) Thermal degradation of medical waste mainly took place in two steps under both pyrolysis and combustion condition; 2) HCl emitted at both two steps and HCl concentration increased with the increased of Cl ratio in the medical waste; 3) for the same additive, HCl concentration decreased with the increased of additives amount, that is to say, HCl removal efficiency of medical waste increased as the increased of Ca/Cl molar ratio. Fourth, when Ca(OH)₂ was used as additive, HCl removal efficiency for medical waste combustion was a little higher than that for medical waste pyrolysis, but either CaCO₃ or CaO was used as additive, it was just opposite, more specifically, when CaCO₃ was used as additive with Ca/Cl=1.3, HCl removal efficiency was 5.49% under pyrolysis condition, but that was only 4.24% under combustion condition. Fifth, under the same Ca/Cl molar ratio, HCl removal efficiency for PVC was higher than that for medical waste under both pyrolysis and combustion condition, more specifically, when Ca(OH)₂ was used as additive with Ca/Cl=1, HCl removal efficiency was 64.51% for PVC, but that was only 27.66% for medical waste pyrolysis with 4% Cl under pyrolysis condition.     

螯合电镀污泥的基本理化特性及燃烧特性

在研究某园区螯合电镀污泥基本理化特性的基础上,针对其含有一定量的有机物及高金属含量的特点,利用红外-热联用技术(TGFTIR)对污泥在空气气氛下的燃烧特性和燃烧过程释放的气体组成进行了研究.结果表明,污泥中的有机物在空气中的燃烧经过4个阶段,其中,有机物的热解、燃烧发生在230~431.01℃范围的第2和第3阶段;燃烧过程会释放CO2、水蒸气和微量NH3、SO2,燃烧温度和控氧量决定释放气体的组成;另外,燃烧过程存在重金属的挥发,可采用有机高分子重金属捕集剂的碱性水溶液喷淋烟气,捕集挥发出的金属,净化焚烧过程释放的酸性气体.考虑到污泥中有机质的充分燃烧、金属铬、铁和铝等金属氢氧化物的分解及部分金属的挥发,污泥焚烧温度应控制在450~500℃左右.研究结果可为此类污泥焚烧热处理提供理论和技术支持.     

生物质内在碱金属催化特性的TG-FTIR实验研究

用热重分析仪和傅里叶红外光谱联用(TG-FTIR)技术对稻秆、谷壳及其经过不同预处理的水洗样、硝酸洗样进行实验研究,分析了生物质内在碱金属对其热解过程的影响.对比原样、水洗样和硝酸洗样的热解TG曲线与产气组分发现:内在碱金属的存在对生物质热解具有较大的催化作用,促进了样品半纤维组分的热分解,明显降低了最大反应速率,使样品分解能够在较低温度段完成,提高了热解过程中焦的生成率,强化了去甲烷化反应,促使热解向羟基乙醛、酸类等低小分子液体产物的方向转化,增大了CO_2和CO的生成量.     

废电脑电线热处理特征

利用热重分析仪/傅立叶变换红外光谱仪(TG-FTIR)联用,测定废电脑电线的热处理特征及其过程产物.结果表明:废电脑电线热处理过程存在2个剧烈失重阶段,第一失重阶段处于250～340 ℃,该温度段失重约45%;第二失重阶段处于420～520 ℃,该温度段失重约10%.加热至600 ℃后样品失重缓慢.废电脑电线热处理产物中既有大量的CO₂和CO,也有烷烃类、脂肪族、芳香族等有机化合物,并且还伴随大量HCl的产生.这些热处理产物主要来源于废电脑电线中有机聚合物以及阻燃剂等添加剂的分解.      

Thermogravimetric coupled with Fourier transform infrared analysis study on thermal treatment of monopotassium phosphate residue

In China, safe disposal of hazardous waste is more and more a necessity, urged by rapid economic development. The pyrolysis and combustion characteristics of a residue from producing monopotassium phosphate (monopotassium phosphate residue), considered as a hazardous waste, were studied using a thermogravimetric, coupled with Fourier transform infrared analyzer (TG-FTIR). Both pyrolysis and combustion runs can be subdivided into three stages: drying, thermal decomposition, and final devolatilization. The average weight loss rate during fast thermal decomposition stage in pyrolysis is higher than combustion. Acetic acid, methane, pentane, (acetyl) cyclopropane, 2,4,6-trichlorophenol, CO, and CO₂ were distinguished in the pyrolysis process, while CO₂ was the dominant combustion product.     

废旧聚氨酯硬泡热解特性

采用热重分析仪对废旧聚氨酯硬泡在氮气中的热失重行为进行了研究,并对升温速率、热解终温对热解的影响进行了分析. 结果表明:在氮气气氛条件下,废旧聚氨酯硬泡热解主要发生在200～492 ℃;随着升温速率的提高,废旧聚氨酯硬泡热失重时挥发分初析温度向高温方向偏移,失重速率峰值(DTG_max)显著增大.利用热重-红外(TG-FTIR)联用方法对氮气气氛中10 ℃/min升温速率下的样品热解气体产物进行了检测. 结果表明:废旧聚氨酯硬泡热解产物有H₂O,CO₂,CO,CFC-11,以及含氯化合物、烯烃类、烷烃类和带有苯环等官能团的化合物,且主要气体产物有相似的析出规律.