胞外聚合物对浸没式膜-生物反应器膜过滤性能的影响

通过浸没式膜-生物反应器（SMBR）处理上海市城市内河水的试验,研究了反应器混合液中和2种疏水性不同的膜上污泥胞外聚合物（EPS）的量、组成、污泥特性及对膜过滤性能的影响.结果表明,混合液污泥中的溶解性EPS和固着性EPS比膜上污泥多,不同污泥的固着性EPS组分中蛋白质（EPSP）/多糖（EPSC）的大小顺序依次为混合液污泥〈亲水膜污泥〈疏水膜污泥.疏水膜污泥中溶解性EPS比亲水膜多,溶解性EPS和固着性EPS量及组分均有很大差异.混合液污泥的EPS流动性大,疏水性膜上污泥EPS的流动性较大.溶解性EPS对污泥特性及膜过滤性能影响较大.SMBR中亲、疏水性膜片上黏附的污泥的相对疏水性分别为53%、59%.比较2种膜片通量的变化发现,疏水性膜污染严重.     

草浆黑液中碱的扩散渗析回收与处理

研究采用扩散渗析法回收草浆黑液中的氢氧化钠,分别采用了离子交换膜和上海交通大学高分子研究所提供的疏水氟膜、亲水氟膜对草浆黑液进行处理。单位膜面积单位体积黑液下阴极室总碱量的增加用R表示。三种膜的R值分别为2.17×10-7mol/(mL·cm2)、9.20×10-8mol/(mL·cm2)、4.39×10-7mol/(mL·cm2)。可见亲水氟膜的扩散渗析效果最好。实验对原黑液及经亲水氟膜扩散渗析得到的稀碱液进行了质谱分析,结果显示只有一部分小分子有机物转移到蒸馏水一侧。从亲水氟膜处理前后的扫描电镜图可以看出亲水氟膜只有较轻微的污染。可见亲水氟膜有最好的扩散渗析效果和较好的使用寿命。     

Improvement of the antifouling characteristics in a bioreactor of polypropylene microporous membrane by the adsorption of Tween 20

Surface modification by physical adsorption of Tween 20 was accomplished on polypropylene microporous membranes (PPMMs). Attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR) and scanning electron microscope (SEM) were used to characterize the chemical and morphological changes on the membrane surfaces. Water contact angles and relative pure water fluxes were measured. The data showed that the hydrophilic performance for the modified membranes increased with the increase in the adsorption amount of Tween 20 onto the surface or into the pores of polypropylene microporous membranes. To test the antifouling property of the membranes by the adsorption of Tween 20 in a membrane bioreactor (MBR), filtration for active sludge was performed using synthetic wastewater. With the help of the data of water fluxes and the FE-SEM photos of the modified PPMMs before or after operating in a MBR for about 12 d, the PPMMs with monolayer adsorption of Tween 20 showed higher remained flux and stronger antifouling ability than unmodified membrane and other modification membranes studied.     

亲水性多孔载体在流化床中的生物膜形成过程分析

采用实验制备的一种新型亲水性多孔聚合物作为流化床反应器中生物膜附着生长的载体,实现流态化水力条件下的生物挂膜过程.在3个结构尺寸相同的流化床反应器中考察了接种污泥浓度、进水有机负荷及载体粒径对亲水性多孔载体生物挂膜量的影响,试验结果表明,接种污泥浓度为30 g VSS/L、进水TOC值为350 mg/L、载体粒径为5～8 mm时载体表面的附着生物量最大,反应器运行12 d的载体附着生物量达到4.45 g VSS/L,膜结构稳定,表现出较活性污泥法更高的活性.在进水TOC、氨氮浓度分别为350 ms/L、50 mg/L,HRT为6 h的情况下,两者的去除率分别达到了97.1%和64.3%,表明载体上的生物膜对污水中TOC及氨氮的去除表现出高效率.挂膜后载体表面上的微生物以丝状菌为主,孔壁上的微生物以球菌和杆菌为主要生物相,证明载体内外表面皆适宜微生物的生长,并且形成合理的生物相分布.     

Fenton法处理垃圾渗滤液MBR-NF浓缩液

采用Fenton法处理MBR-NF浓缩液,考察了FeSO4·7H2O投加量、n(H2O2)/n(Fe2+)投加比、初始pH对渗滤液MBR-NF浓缩液处理效果的影响,并在最佳实验条件下,探讨浓缩液富里酸(FA)、亲水性有机物(HyI)组分在Fenton氧化前后组成的变化。研究结果表明,在FeSO4·7H2O投加量为0.055 mol/L、n(H2O2)/n(Fe2+)投加比为4、初始pH为7.58时,对COD、腐植酸(UV254)、色度(CN)的去除率分别为79.6%、93.7%和97.8%。Fenton氧化后,浓缩液中有机物组分含量发生了较大变化,腐植酸含量下降,HyI成为渗滤液溶解性有机物主要成分。紫外-可见光谱表明,Fenton法对FA去除效果较好,而对HyI氧化效果较差;傅立叶红外光谱显示,经Fenton氧化后,FA的结构发生了明显变化,而HyI则变化不明显。     

组合工艺处理填埋场渗滤液中溶解性有机污染物的去除特性

以采用"SBR+混凝+Fenton氧化+BAF"组合工艺处理的晚期垃圾渗滤液各级出水为研究对象,考察了HA、FA和HyI等溶解性有机物(DOM s)在各个工艺处理过程中的变化。结果表明,组合工艺COD和NH3-N去除率分别达到98.4%和99.3%;对DOM s的去除率为98.3%,其中胡敏酸(HA)、富里酸(FA)和亲水性有机物(HyI)的去除率分别为98.3%、99.5%和95.7%。各处理工艺中SBR和混凝工艺对HA和HyI的去除贡献较大,Fenton氧化工艺对FA去除率较高。Fenton氧化和BAF联用,可以有效去除难降解的溶解性有机污染物,使出水达到《生活垃圾填埋污染控制标准》(GB16889-2008)排放标准。     

黄河干流宁蒙段溶解性有机物组分特征及其与金属离子的相关性

溶解性有机物(dissolved organic matter,DOM)是天然水体的重要组成部分,由于化学极性及所含的官能团不同,其在水体中的化学行为也不同.本研究以黄河干流宁蒙段为研究对象,于2015年4月采集了下河沿至头道拐沿程7个断面的水样,采用XAD系列树脂将DOM分为疏水性酸(hydrophobic acid,HOA)、疏水性碱(hydrophobic base,HOB)、弱疏水性酸(weak hydrophobic acid,WHOA)和亲水性物质(hydrophilic matter,HYI)这4个组分,探讨了DOM组分含量、荧光峰值及其与Pb、Zn、Cu、Cr、As这5种金属离子之间的相关性.结果表明,黄河宁蒙段DOM总量由下河沿至头道拐沿程逐渐增加.各断面DOM腐殖化程度较低,以亲水性的蛋白质类小分子物质(HYI)为主,疏水性酸(HOA)次之,这与黄河沿岸排污导致内源作用增强有关.三维荧光光谱中类腐殖质和类蛋白质荧光峰型显著,且类腐殖质峰沿程逐渐增强,进一步证实了内源污水输入的影响.SPSS相关性分析结果表明,DOM与5种金属离子呈现出不同程度的相关性,其中与Cu离子显著相关;4种组分中HYI与Cu离子的相关性最强,说明二者在迁移转化过程中存在显著相互作用.进一步研究发现,芳香蛋白类物质荧光峰强度随Cu离子浓度的升高而降低,这可能是Cu与亲水性组分中的芳香类蛋白质发生络合产生荧光淬灭效应,从而导致荧光强度降低.     

Removal of organic matter and disinfection by-products precursors in a hybrid process combining ozonation with ceramic membrane ultrafiltration

The performance of an integrated process including coagulation, ozonation, ceramic ultrafiltration (UF) and biologic activated carbon (BAC) filtration was investigated for the removal of organic matter and disinfection by-products (DBPs) precursors from micro-polluted surface water. A pilot scale plant with the capacity of 120 m³ per day was set up and operated for the treatment of drinking water. Ceramic membranes were used with the filtration area of 50 m² and a pore size of 60 nm. Dissolved organic matter was divided into five fractions including hydrophobic acid (HoA), base (HoB) and neutral (HoN), weakly hydrophobic acid (WHoA) and hydrophilic matter (HiM) by DAX-8 and XAD-4 resins. The experiment results showed that the removal of organic matter was significantly improved with ozonation in advance. In sum, the integrated process removed 73% of dissolved organic carbon (DOC), 87% of UV₂₅₄, 77% of trihalomethane (THMs) precursors, 76% of haloacetic acid (HAAs) precursors, 83%of trichloracetic aldehyde (CH) precursor, 77% of dichloroacetonitrile (DCAN) precursor, 51% of trichloroacetonitrile (TCAN) precursor, 96% of 1,1,1-trichloroacetone (TCP) precursor and 63% of trichloronitromethane (TCNM) precursor. Hydrophobic organic matter was converted into hydrophilic organic matter during ozonation/UF, while the organic matter with molecular weight of 1000–3000 Da was remarkably decreased and converted into lower molecular weight organic matter ranged from 200–500 Da. DOC had a close linear relationship with the formation potential of DBPs.     

发酵制药废水二级出水中溶解性有机物特性分析

溶解性有机物（DOM）是发酵制药废水二级生化尾水深度处理工艺的主要去除对象,深入解析废水中DOM的特性是将其有效去除的前提和关键.本研究采集氨基酸类、头孢类、抗生素类、维生素类、阿维菌素类5种发酵制药废水二级出水,通过XAD-8树脂亲疏水性分离、凝胶色谱分子量分级、傅里叶变换红外光谱和三维荧光表征对二级出水中的DOM进行特性分析.结果表明,5种发酵制药废水二级出水的盐度和色度高,废水中有机物浓度高、波动大（48.60~245.40 mg·L^-1）.DOM大多数以疏水性组分为主,分子量分布广泛（210~10000 Da）.二级出水DOM均含有大量的不饱和双键、苯环结构,同时含有—OH、—NH₂和C=O等发色团和助色基团,造成废水色度较高.通过对发酵制药废水二级出水进行EEM-PARAFAC分析确定了4种荧光组分特征峰,包括3种腐殖质类（C1、C3、C4）和1种类蛋白类组分（C2）.发酵制药废水二级出水中DOM主要是以类腐殖质有机物为主（C1、C3）.全方面识别和解析发酵制药废水DOM的组成,可为废水深度处理工艺的优化提供指导.     

Particle Surface Hydrophobicity and the Dechlorination of Chloro-Compounds by Iron Sulfides

Halogenated aliphatic compounds (HACs) can be reduced by iron sulfides in aqueous systems. Generally, the thermodynamics and kinetics of dehalogenation reactions are controlled by the mineralogical and particle surface characteristics of the iron sulfide, the composition of the HAC and reaction conditions such as component concentrations, pH and Eh. In this theoretical and experimental investigation of CCl₄ and C₂Cl₆ reduction by FeS and FeS₂, the roles of hydrophobic and hydrophilic sites on the iron sulfides were analyzed. Experimental data obtained through zeta potential measurements, were used along with the Gouy-Chapman model and the simple two-layer surface complexation model to relate iron sulfide surface hydroxyl densities to the degree of HAC dehalogenation. The surface hydroxyl site densities of FeS and FeS₂ were found to be 0.11 sites/nm² and 0.21 sites/nm², respectively. During the dehalogenation reaction process, CCl₄ was found to decrease to its first intermediate product CHCl₃ within the first 20 hours followed by a slower process of conversion to CH₂Cl₂. The results also show that FeS is less hydrated (more hydrophobic) than FeS₂. For CCl₄ and C₂Cl₆, FeS is a better dehalogenator than FeS₂. These results imply that particle surface hydrophobicity is a critical factor in surface-mediated dehalogenation of chlorinated compounds.