排序方式: 共有24条查询结果,搜索用时 15 毫秒
1.
设计良好的导电回路对真空断路器灭弧性能的提高有着重要的意义。本文首先从结构上分析了三种不同导电回路的优缺点,接着,分析了三种不同导电回路的电动斥力和吹弧磁场,为通过选择不同导电回路,触头直径和开距提高真空断路器灭弧性能提供方法和思路。 相似文献
2.
O/W型乳化液的处理 总被引:3,自引:0,他引:3
采用药剂破乳-电解破乳工艺处理O/W型乳化液,药剂破乳选用聚合硫酸铁为破乳剂,破乳时最佳PH为8,聚合硫酸铁的最佳投量为1500mg/L,电解破乳选用铁作阳极,铝作阴极,电流密度0.86A/dm^2,极距25mm,电解时间3h。在上述条件下,破乳效果良好,出水清澈透明,COD总去除率可达到96-97%。 相似文献
3.
在大型造纸厂经常会遇到使用200~1 000 k W变频电动机的情况。因为0.38 k V电机生产工艺的原因不可能做到很大功率,而中压(10 k V,6 k V)的变频器因为价格、安全与稳定性的原因也有其缺陷,所以0.69 k V这个电压等级的变频器就有了用武之地。 相似文献
4.
废弃饱和盐水钻井液的固液分离 总被引:2,自引:0,他引:2
采用化学破胶脱稳和压滤机械分离的化学强化固液分离技术处理江汉油田废弃饱和盐水钻井液(简称废钻井液).最佳固液分离工艺为:调节废钻井液的pH为6.5左右,先加入无机破胶剂(HWJ),HWJ的加入量为15 000 mg/L,以400 r/min的转速搅拌3 min,稀释1倍后,再加入有机破胶剂(HYJ),HYJ的加入量为300 mg/L,以120 r/min的转速搅拌5min.固液分离结果表明,分离后出水率达68.2%,而泥饼湿含量只有55.8%,废钻井液的COD由67 886.8 mg/L降至8 898.9 mg/L. 相似文献
5.
6.
7.
张金梅 《中国安全生产科学技术》2013,9(7):66-70
为评价过硫酸铵胶囊破胶剂的混储危险性,测试了过硫酸铵胶囊破胶剂的氧化性,并分别采用压力传感器法和差示扫描量热法测试了非氧化剂过硫酸铵胶囊破胶剂与其他化学品的相容性。试验发现,过硫酸铵胶囊破胶剂由于外壳的包覆作用,其氧化性下降,个别过硫酸铵胶囊破胶剂不属氧化剂;但是通过相容性测试发现,过硫酸铵胶囊破胶剂与多数有机物质不相容。因此在储存过程中应与可燃物质以及还原剂等隔离。 相似文献
8.
主要应用于舰船等有冲击场合的断路器,其抗冲击性能要求很高。介绍了断路器欠压脱扣器在抗冲击方面的设计方法,此方法可以有效地削弱冲击力对欠压脱扣器的影响。 相似文献
9.
10.
In India coal production will have to be increased to meat theenergy demand at a very high rate. By 2000 AD the coolproduction from opencast (O/C) mining will rise to 250 Mt. whichwill be about 70% of the total coal production. The increasing trend of O/C mining leads to cause air pollution problem. A surveywas conducted to assess the status of work zone air envirnmentdue to opencast coal mining in Jharia Coalfield. Keeping in viewof place of dust generation air quality monitoring stations wereselected. Methodology adapted for sampling and analysis of airpollutants have been described. Four season data revealed thatmaximum concentration of SPM was observed at dragline sectionand the next high concentration was at haul roads. At all thelocations SPM and RPM concentrations exceeded the permissiblelimits specified by Indian Pollution Control Board. Shift wiseand location wise analysis for getting higher concentration ofSO2 and NOx have been discussed. Wind velocity anddirections, mixing heights, ventilation coefficient of the areahave been analyzed. Huge dust generation creates vision problemto HEMM operators. The methodology adopted may be utilised onindustrial scale for various sites. 相似文献