DISCHARGE AND SUSPENDED SEDIMENT PATTERNS OF AN INTERMITTENT COLD DESERT STREAM1

Sage Creek in south‐central Wyoming is listed as impaired by the U.S. Environmental Protection Agency (USEPA) due to its sediment contribution to the North Platte River. Despite the magnitude of sediment impacts on streams, little research has been conducted to characterize patterns of sediment transport or to model suspended sediment concentration in many arid western U.S. streams. This study examined the relationship between stream discharge and suspended sediment concentration near the Sage Creek and North Platte River confluence from 1998 through 2003. The objectives were to determine patterns of stream discharge and suspended sediment concentration, produce a sediment prediction model, and compare sediment concentrations for the six‐year period. Stream discharge and suspended sediment transport responded rapidly to convective storms and spring runoff events. During the study period, events exceeding 0.23 m³/s accounted for 92 percent of the sediment load, which is believed to originate from erodible headwater uplands. Further analysis of these data indicates that time series modeling is superior to simple linear regression in predicting sediment concentration. Significant increases in suspended sediment concentration occurred in all years except 2003. This analysis suggests that a six‐year monitoring record was insufficient to factor out impacts from climate, geology, and historical sediment storage.     

Concentration‐Duration‐Frequency Curves for Stream Turbidity: Possibilities for Assessing Biological Impairment1

Abstract: Siltation and subsequent biological impairment is a national problem prompting state regulatory agencies to develop sediment total maximum daily loads (TMDL) for many streams. To support TMDL targets for reduced sediment yield in disturbed watersheds, a critical need exists for stream assessments to identify threshold concentrations of suspended sediment that impact aquatic biota. Because of the episodic nature of stream sediment transport, thresholds should not only be a function of sediment concentration, but also of duration and dose frequency. Water quality sondes can collect voluminous amounts of turbidity data, a surrogate for suspended sediment, at intervals that can be used to characterize concentration, duration, and frequency of elevated turbidity events. To characterize turbidity sonde data in an ecologically relevant manner, a methodology for concentration‐duration‐frequency (CDF) curves was developed using turbidity doses that relate to different levels of biological impairment. To illustrate this methodology, turbidity CDF curves were generated for two sites on Little Pigeon River in the Great Smoky Mountains National Park, Tennessee, using over 30,000 sonde data measurements per site for a one‐year period. Utilizing a Poisson arrival approach, turbidity spikes were analyzed stochastically by observing the frequency and duration of recorded events over a turbidity level that relates to a biological dose response. An exponential equation was used to fit duration and frequency of a specified turbidity level to generate concentric‐shaped CDF curves, where at specific turbidities longer durations occurred less frequently and conversely shorter durations occurred more frequently. The significance of the equation fit to the data was accomplished with a Kolmogorov‐Smirnov goodness‐of‐fit test. Our findings showed that the CDF curves derived by an exponential function performed reasonable well, with most curves significant at a 95% confidence level. These CDF curves were then used to demonstrate how they could be used to assess biological impairment, and identify future research needs for improved development of sediment TMDLs.     

Quality and Quantity of Suspended Particles in Rivers: Continent-Scale Patterns in the United States

Suspended solids or sediments can be pollutants in rivers, but they are also an important component of lotic food webs. Suspended sediment data for rivers were obtained from a United States–wide water quality database for 622 stations. Data for particulate nitrogen, suspended carbon, discharge, watershed area, land use, and population were also used. Stations were classified by United States Environmental Protection Agency ecoregions to assess relationships between terrestrial habitats and the quality and quantity of total suspended solids (TSS). Results indicate that nephelometric determinations of mean turbidity can be used to estimate mean suspended sediment values to within an order of magnitude (r² = 0.89). Water quality is often considered impaired above 80 mg TSS L^–1, and 35% of the stations examined during this study had mean values exceeding this level. Forested systems had substantially lower TSS and somewhat higher carbon-to-nitrogen ratios of suspended materials. The correlation between TSS and discharge was moderately well described by an exponential relationship, with the power of the exponent indicating potential acute sediment events in rivers. Mean sediment values and power of the exponent varied significantly with ecoregion, but TSS values were also influenced by land use practices and geomorphological characteristics. Results confirm that, based on current water quality standards, excessive suspended solids impair numerous rivers in the United States.     

SEDIMENT TRANSPORT DURING A CONTROLLED RESERVOIR RELEASE1

The transport of bedload and suspended sediments and particulate organic matter was evaluated in Huntington Creek, Utah, during a controlled release of water from Electric Lake Reservoir from August 7–10, 1979. Effects of the release on channel geometry and riffle composition also were assessed. Bedload transport rates increased from zero to 1,650 and 1,500 kg/hr at two cross sections as discharge was increased from 0.4 to 4.9 m³/s; transport rates then decreased erratically as discharge was held constant. Cross section measurements and sediment size analysis indicate that flows were insufficient to transport riffle sediments. Rapid increases in the transport rates of suspended sediments and particulate organic matter also occurred during rising discharge and again decayed when discharge became constant. Suspended sediment concentrations for samples obtained with an automatic pumping sampler were generally less than those found for samples obtained with a DH-48 sampler. Biological measurements still are needed to determine if such a release can improve fisheries habitat by removing fine sediments.     

PATTERNS OF SUSPENDED SEDIMENT TRANSPORT IN A COASTAL ALASKA STREAM1

Suspended sediment data from a 154 ha watershed on northeast Chichagof Island, Alaska, were collected over three fall storm seasons from 1980 to 1982. Sediment rating curves for nine pooled storms explained less than 34 percent of the variation in total suspended solids (TSS). Significantly higher concentrations of suspended sediment occurred during the rising limb of storm hydrographs than for similar flows on the falling limb, accounting for hysteresis loops in TSS versus streamflow plots for individual storms. These hysteresis loops were wider during early season storms, indicating that easily transportable fine sediment may have been flushed from the upper portion of channel banks and from behind large organic debris during early season peak flows. Regression relationships (TSS versus Q) developed for the highest stormflows (> 1 m³/s) had steeper slopes than the lower stormflows (< 1 m³/s). Turbidity correlated well (r=0.94) with TSS for all storm-flow data combined. Organic matter constituted an average of 35 percent (by weight) of TSS for all water quality samples.     

PROCESS-ORIENTED ESTIMATION OF SUSPENDED SEDIMENT CONCENTRATION1

ABSTRACT: Least squares regression and ARIMA models were developed from suspended sediment data for the Ausable River, Southern Ontario, Canada. A poor correlation between discharge and suspended sediment concentration results from the dynamics of the physical system, including seasonality, antecedent conditions, and hysteresis. Regression model results were significantly improved by the division of the data set into seasons and the addition of simple. but physically meaningful variables. Misleading improvements obtained from the regression of sediment load and discharge are discussed. ARIMA models provided accurate forecasts of sediment concentration on a real-time basis, but the rigorous data requirements limit their use in modeling suspended sediment concentrations in Canadian rivers.     

ESTIMATING THE SUSPENDED SEDIMENT LOAD IN RESERVOIRS1

ABSTRACT: The total suspended sediment loads of four north Mississippi reservoirs were determined from measurements of concentrations of suspended sediment in a vertical profile at several locations on each reservoir made during the year. These data were combined with the stage-height and known stage-volume relationships for each reservoir in a numerical integration to determine the total suspended sediment in the water body. Total suspended sediments were estimated using the product of the suspended sediment concentration in the surface water by the appropriate reservoir volume. The averaged ratios of the estimated to measured suspended sediment loads for each reservoir exceeded 0.90. Since the concentration of suspended sediments in surface waters of north Mississippi reservoirs has been shown as highly correlated with spectral reflectance, estimating the total suspended sediment of these reservoirs using remotely sensed spectral reflectance data is possible.     

SOME SUSPENDED SEDIMENT YIELDS FROM SOUTH ISLAND CATCHMENTS,NEW ZEALAND1

: Estimates of specific annual suspended sediment yields, some of which rank among the highest reported in the world, are presented for 33 basins of South Island, New Zealand. Yield from each basin was determined by combining a suspended sediment concentration rating with the complete flow record of each catchment stream gaging station. A multiple regression analysis between sediment yields and climatic, hydrologic and physiographic parameters of each basin demonstrates that most of the variance in yields is explained by catchment mean rainfall. Geology apparently has little influence on sediment yield as suspended sediment concentration ratings, from rivers draining catchments of differing lithology, and regolith, are indistinguishable. Specific suspended sediment yield prediction equations are given for four defined regions covering in area almost all South Island; and except for one area, feature rainfall as the principle independent variable. Differences between regions may be due to variations in intensity, frequency, and duration patterns of storms. It is proposed that a simple power law relationship between yield and rainfall provides useful suspended sediment yield estimates in mountainous regions of temperate maritime climate, provided catchments have not been modified extensively by man.     

SUSPENDED SEDIMENT AND TURBIDITY FOLLOWING ROAD CONSTRUCTION AND LOGGING IN WESTERN MONTANA1

ABSTRACT: Forest management activities in a second order drainage basin increased suspended sediment yields 7.7 fold in the first year following road construction, and two-fold following logging in the second year. Sediment supply limitations resulted in poor correlations between sediment concentrations with discharge. Sediment transport was strongly hysteretic, with the highest sediment concentrations occurring on the rising limbs of snowmelt hydrographs and individual peaks. In addition to discharge, hydrograph characteristics such as limb, dQ/dt, and the product of dQ/dt and limb aided in explaining variability of observed sediment concentrations. Sediment-turbidity relationships were strongly discharge dependent, reflecting the changing composition of the suspended load with stream power and sediment supplies.     

Enhancing Hyrdological Simulation Program – FORTRAN Model Channel Hydraulic Representation1

Abstract: The hydrological simulation program – FORTRAN (HSPF) is a comprehensive watershed model that employs depth‐area‐volume‐flow relationships known as the hydraulic function table (FTABLE) to represent the hydraulic characteristics of stream channel cross‐sections and reservoirs. An accurate FTABLE determination for a stream cross‐section site requires an accurate determination of mean flow depth, mean flow width, roughness coefficient, longitudinal bed slope, and length of stream reach. A method that uses regional regression equations to estimate mean flow depth, mean flow width, and roughness coefficient is presented herein. FTABLES generated by the proposed method (Alternative Method) and FTABLES generated by Better Assessment Science Integrating Point and Nonpoint Sources (BASINS) were compared. As a result, the Alternative Method was judged to be an enhancement over the BASINS method. First, the Alternative Method employs a spatially variable roughness coefficient, whereas BASINS employs an arbitrarily selected spatially uniform roughness coefficient. Second, the Alternative Method uses mean flow width and mean flow depth estimated from regional regression equations whereas BASINS uses mean flow width and depth extracted from the National Hydrography Dataset (NHD). Third, the Alternative Method offers an option to use separate roughness coefficients for the in‐channel and floodplain sections of compound channels. Fourth, the Alternative Method has higher resolution in the sense that area, volume, and flow data are calculated at smaller depth intervals than the BASINS method. To test whether the Alternative Method enhances channel hydraulic representation over the BASINS method, comparisons of observed and simulated streamflow, flow velocity, and suspended sediment were made for four test watersheds. These comparisons revealed that the method used to estimate the FTABLE has little influence on hydrologic calibration, but greatly influences hydraulic and suspended sediment calibration. The hydrologic calibration results showed that observed versus simulated daily streamflow comparisons had Nash‐Sutcliffe efficiencies ranging from 0.50 to 0.61 and monthly comparisons had efficiencies ranging from 0.61 to 0.84. Comparisons of observed and simulated suspended sediments concentrations had model efficiencies ranging from 0.48 to 0.56 for the daily, and 0.28 to 0.70 for the monthly comparisons. The overall results of the hydrological, hydraulic, and suspended sediment concentration comparisons show that the Alternative Method yielded a relatively more accurate FTABLE than the BASINS method. This study concludes that hydraulic calibration enhances suspended sediment simulation performance, but even greater improvement in suspended sediment calibration can be achieved when hydrological simulation performance is improved. Any improvements in hydrological simulation performance are subject to improvements in the temporal and spatial representation of the precipitation data.     

THE SUSPENDED SEDIMENT REGIME OF AN OREGON COAST RANGE STREAM1

ABSTRACT: Armored stream segments may affect the suspended sediment regime of small mountain streams in western Oregon by the release of fine sediments stored in the bed gravels. Sieve analysis of bed materials indicated that at least 30 percent of the suspended sediment yield for the 1975–76 winter had been stored in the streambed. Suspended sediment concentrations during storm-generated runoff were influenced by stream discharge and hydrograph characteristics. Sediment-discharge relations for individual storms were characterized by hysteresis loops. A seasonal flushing of fines was shown by a progressive decrease in the ratio of suspended sediment to stream discharge during the winter runoff period.     

ALAWAT: A spatially allocated watershed model for approximating stream,sediment, and pollutant flows in Hawaii,USA

The Ala Wai Canal Watershed Model (ALAWAT) is a planning-level watershed model for approximating direct runoff, streamflow, sediment loads, and loads for up to five pollutants. ALAWAT uses raster GIS data layers including land use, SCS soil hydrologic groups, annual rainfall, and subwatershed delineations as direct model parameter inputs and can use daily total rainfall from up to ten rain gauges and streamflow from up to ten stream gauges. ALAWAT uses a daily time step and can simulate flows for up to ten-year periods and for up to 50 subwatersheds. Pollutant loads are approximated using a user-defined combination of rating curve relationships, mean event concentrations, and loading/washoff parameters for specific subwatersheds, land uses, and times of year. Using ALAWAT, annual average streamflow and baseflow relationships and urban suspended sediment loads were approximated for the Ala Wai Canal watershed (about 10,400 acres) on the island of Oahu, Hawaii. Annual average urban suspended sediments were approximated using two methods: mean event concentrations and pollutant loading and washoff. Parameters for the pollutant loading and washoff method were then modified to simulate the effect of various street sweeping intervals on sediment loads.     

Reduction of stream sediment concentration by a riparian buffer: filtering of road runoff in disturbed headwater basins of montane mainland southeast Asia

We determined the extent that a riparian buffer reduces stream suspended sediment concentrations by filtering road runoff during 18 rain events in a 2.5-ha, multi-use watershed in northern Thailand. The dominant buffer species was the perennial sedge Fimbristylis aphylla Zoll. ex Steud. (Cyperaceae). We monitored stream sediment concentration for situations where road runoff either flowed into the riparian buffer or was diverted directly into the stream (buffer and no buffer scenarios). These data were used to develop the following relationships between instantaneous stream sediment concentration (Ci) and discharge (Qi): Ci= 28.329Qi(0.851) (buffer scenario) and Ci= 22.265Qi(1.579) (no buffer scenario). Using these functions to calculate total event suspended concentrations, we determined that the buffer reduced suspended sediment concentration by 34 to 87%, for the range of events monitored. Removal of sediment from runoff generated on a 2.4-m-wide, 165-m-long unpaved road section was achieved principally via ponding, which reduced the transport capacity as flow entered the relatively flat, saturated buffer. Sediment deposition occurred primarily within the first 10 m of the buffer. Some sediment was also deposited on the fillslope leading to the buffer. Maximum road sediment concentration during the largest buffer event approached 100,000 mg L(-1). Meanwhile, the corresponding maximum stream suspended sediment concentration was <4000 mg L(-1). In contrast, maximum stream concentrations when flow bypassed the buffer during smaller events were commonly 4000 to 7000 mg L(-1). Naturally occurring buffers represent an economical means of mitigating road-related impacts in upland basins in Southeast Asia, particularly if combined with measures limiting sediment and runoff production on contributing road sections.     

ELECTRONIC DATA PROCESSING SYSTEM FOR STREAMFLOW1

Daily, monthly, and yearly summaries of streamflow and sediment transport are computed from continuous gage height records and discrete measurements of sediment concentration and discharge rate. The system includes computer computation of discharge measurement notes and an accuracy check of gage height and time input data. Maximum volumes of runoff for selected time intervals up to eight days and flow duration data can also be compiled. Electronic data processing equipment including a chart reader, card punch, computers, and card sorter are used. The system software includes 12 Fortran programs.     

Contribution of In‐Channel Processes to Sediment Yield of an Urbanizing Watershed1

Abstract: A study was conducted between September 2003 and September 2006 to obtain baseline sediment inventories and monitor sediment transport and storage along a 3.7 km length of the channel of Valley Creek within Valley Forge National Historical Park, Pennsylvania. Valley Creek is a tributary of the Schuylkill River and drains an urbanizing 60.6 km² watershed that currently has 18% impervious land cover. Numerous field methods were employed to measure the suspended sediment yield, longitudinal profile, cross‐sections, banklines, and particle size distribution of the streambed. Suspended sediment yield for the watershed was measured at a USGS gage located just upstream of the park boundary between July 2004 and July 2005, the period corresponding to field surveys of bank erosion and channel change. The estimated suspended sediment yield of 95.7 t/km²/year is representative of a year with unusually high discharge, including a storm event that produced a peak of 78 m³/s, the second highest discharge on record for the USGS gage. Based on the median annual streamflow for the 24 years of record at the USGS gage from 1983 to 2006, the median annual sediment yield is estimated to be closer to 34 t/km²/year, considerably lower than median and mean values for other sites within the region. The mass of silt, clay, and fine sand derived from bank erosion along the 3.7 km study reach during the field survey period accounts for an estimated 2,340 t, equivalent to about 43% of the suspended sediment load. The mass of fine sediment stored in the bed along the study reach was estimated at 1,500 t, with about 330 t of net erosion during the study period. Although bank erosion appears to be a potentially dominant source of sediment by comparison with annual suspended sediment load, bed sediment storage and potential for remobilization is of the same order of magnitude as the mass of sediment derived from bank erosion.     

Using turbidity and acoustic backscatter intensity as surrogate measures of suspended sediment concentration in a small subtropical estuary

The suspended sediment concentration is a key element in stream monitoring, although the turbidity and acoustic Doppler backscattering may be suitable surrogate measures. Herein a series of new experiments were conducted in laboratory under controlled conditions using water and mud samples collected in a small subtropical estuary of Eastern Australia. The relationship between suspended sediment concentration and turbidity exhibited a linear relationship, while the relationships between suspended sediment concentration and acoustic backscatter intensity showed a monotonic increase. The calibration curves were affected by both sediment material characteristics and water quality properties, implying that the calibration of an acoustic Doppler system must be performed with the waters and soil materials of the natural system. The results were applied to some field studies in the estuary during which the acoustic Doppler velocimeter was sampled continuously at high frequency. The data yielded the instantaneous suspended sediment flux per unit area in the estuarine zone. They showed some significant fluctuations in instantaneous suspended mass flux, with a net upstream-suspended mass flux during flood tide and net downstream sediment flux during ebb tide. For each tidal cycle, the integration of the suspended sediment flux per unit area data with respect of time yielded some net upstream sediment flux in average.     

Applications of Turbidity Monitoring to Forest Management in California

Many California streams have been adversely affected by sedimentation caused by historic and current land uses, including timber harvesting. The impacts of timber harvesting and logging transportation systems on erosion and sediment delivery can be directly measured, modeled, or inferred from water quality measurements. California regulatory agencies, researchers, and land owners have adopted turbidity monitoring to determine effects of forest management practices on suspended sediment loads and water quality at watershed, project, and site scales. Watershed-scale trends in sediment discharge and responses to current forest practices may be estimated from data collected at automated sampling stations that measure turbidity, stream flow, suspended sediment concentrations, and other water quality parameters. Future results from these studies will provide a basis for assessing the effectiveness of modern forest practice regulations in protecting water quality. At the project scale, manual sampling of water column turbidity during high stream flow events within and downstream from active timber harvest plans can identify emerging sediment sources. Remedial actions can then be taken by managers to prevent or mitigate water quality impacts. At the site scale, manual turbidity sampling during storms or high stream flow events at sites located upstream and downstream from new, upgraded, or decommissioned stream crossings has proven to be a valuable way to determine whether measures taken to prevent post-construction erosion and sediment production are effective. Turbidity monitoring at the project and site scales is therefore an important tool for adaptive management. Uncertainty regarding the effects of current forest practices must be resolved through watershed-scale experiments. In the short term, this uncertainty will stimulate increased use of project and site-scale monitoring.     

TEMPORAL CHANGES IN THE YADKIN RIVER FLOW VERSUS SUSPENDED SEDIMENT CONCENTRATION RELATIONSHIP1

ABSTRACT: Dynamic linear models (DLM) and seasonal trend decomposition (STL) using local regression, or LOESS, were used to analyze the 50‐year time series of suspended sediment concentrations for the Yadkin River, measured at the U.S. Geological Survey station at Yadkin College, North Carolina. A DLM with constant trend, seasonality, and a log₁₀ streamflow regressor provided the best model to predict monthly mean log₁₀ suspended sediment concentrations, based on the forecast log likelihood. Using DLM, there was evidence (odds approximately 69:1) that the log₁₀ streamflow versus log₁₀ suspended sediment concentration relationship has changed, with an approximate 20 percent increase in the log₁₀ streamflow coefficient over the period 1981 to 1996. However, sediment concentrations in the Yadkin River have decreased during the decade of the 1990s, which has been accompanied by a concomitant increase in streamflow variability. Although STL has been shown to be a versatile trend analysis technique, DLM is shown to be more suitable for discovery and inference of structural changes (trends) in the model coefficient describing the relationship between flow and sediment concentration.     

SEDIMENT TRANSPORT IN A SHALLOW COASTAL ESTUARY DURING THE WINTER SEASON1

ABSTRACT: This project analyzes suspended sediment flux through the upper Barataria basin in Louisiana during the winter season defined from November through April. The Barataria is a shallow coastal estuary located in southeastern Louisiana. The controls exerted by environmental parameters (such as wind or atmospheric pressure) in wetlands‐shallow bay ecosystems on transport of water and sediment were examined. Water samples were taken at a bayou (which serve as the inlet for flow to the estuary) on a regular basis. These samples were analyzed for total suspended solids and volatile suspended solids. Velocity, depth, temperature, salinity, conductivity, and meteorological measurements were all recorded at the time of each sampling. A multi‐parameter field probe was employed to continually monitor turbidity, water level, conductivity, and temperature during frontal events. These data were used in a regression analysis to examine the factors that drive carbon flux in the region. Investigations have determined that synoptic climate and prevailing weather conditions explain much of the variations in water levels, flow circulation patterns, salinity, and suspended sediment. Relatively small amounts of sediment appear to leave the estuary during normal tidal activity, but winter storm fronts result in significant fluxes of sediment in both up‐basin and down‐basin directions.     

On the Role of Spatial,Temporal, and Climatic Forces on Stream Sediment Loading from Rural and Urban Ecosystems

In this study, we characterize the greatest sediment loading events by their sediment delivery behavior; dominant climate, watershed, and antecedent conditions; and their seasonal distribution for rural and urban land uses. The study area is Paradise Creek Watershed, a mixed land use watershed in northern Idaho dominated by saturation excess processes in the upstream rural area and infiltration excess in the downstream urban area. We analyzed 12 years of continuous streamflow, precipitation, and watershed data at two monitoring stations. We identified 137 sediment loading events in the upstream rural section of the watershed and 191 events in the downstream urban section. During the majority of these events conditions were transport limited and the sediment flush occurred early in the event, generally in the first 20% of elapsed event time. Statistical analysis including two dozen explanatory variables showed peak discharge, event duration, and antecedent baseflow explained most of the variation in event sediment load at both stations and for the watershed as a whole (R² = 0.73‐0.78). In the rural area, saturated soils combined with spring snowmelt in March led to the greatest loading events. The urban area load contribution peaked in January, which could be a re‐suspension of streambed sediments from the previous water year. Throughout the study period, one event contributed, on average, 33% of the annual sediment load but only accounted for 2% of the time in a year.