Potential contributions of clay minerals and organic matter to pentachlorophenol retention in soils

Sorption of pentachlorophenol (PCP) by pure minerals and humic acids were measured to obtain additional perspective on the potential contributions of both clay minerals and soil organic matter (SOM) to contaminants retention in soils. Four types of common soil minerals and two kinds of humic acids (HAs) were tested. The sorption affinity for PCP conformed to an order of HAs > K-montmorillonite > Ca-montmorillonite > goethite > kaolinite. Such a difference in sorption capacity could be attributed to the crucial control of HAs. Clay minerals also had their contribution, especially K-montmorillonite, which played an important, if not dominant, role in the controlling process of PCP sorption. By removing 80% (on average) of the organic carbon from the soils with H(2)O(2), the sorption decreased by an average of 50%. The sorption reversibility had been greatly favored as well. Considering the uncharged mineral fractions in soil before and after H(2)O(2)-treated, the main variation in sorption behavior of the soil might thus be related to the removed organic carbon and the reduced pH. This testified rightly the interactive effect of SOM and clay minerals on PCP sorption as a function of pH.     

The ratio of clay content to total organic carbon content is a useful parameter to predict adsorption of the herbicide butachlor in soils

Thirteen soils collected from 11 provinces in eastern China were used to investigate the butachlor adsorption. The results indicated that the total organic carbon (TOC) content, clay content, amorphous Fe2O3 content, silt content, CEC, and pH had a combined effect on the butachlor sorption on soil. Combination of the data obtained from the 13 soils in the present study with other 23 soil samples reported by other researchers in the literature showed that Koc would be a poor predictive parameter for butachlor adsorption on soils with TOC content higher than 4.0% and lower than 0.2%. The soils with the ratio of clay content to TOC content (RCO) values less than 60 adsorbed butachlor mainly by the partition into soil organic matter matrix. The soils with RCO values higher than 60 apparently adsorbed butachlor by the combination of the partition into soil organic matter matrix and adsorption on clay surface.     

不同粒径泥沙理化特性对磷吸附过程的影响

以北京大兴南海子湖表层沉积物为研究对象,测试分析了0.147～0.246 mm(细砂)、0.074～0.147 mm(极细砂)、0.0385～0.0740 mm(粉粒)和<0.0385 mm(粉粒粘粒混合物)4种粒径泥沙对磷的吸附行为,并采用相关分析及逐步回归分析探讨不同粒径沉积物中有机质(OM)、Fe、Al、Ca、Mn和TP含量对磷吸附过程的影响。结果表明,二级动力学方程和Langmuir模型能较好地描述南海子不同粒径泥沙的吸附动力学及等温吸附过程(R2>0.90)。粒径对单位质量泥沙吸附磷量具有明显影响,粉粒粘粒混合物>粉粒>细砂>极细砂。总体上,泥沙有机质(OM)、TP、Fe、Al、Ca和Mn含量随粒径的减小而增大,且粘粒对其影响较大。不同粒径泥沙(OM)、Fe、Al、Ca和Mn含量之间存在极显著正相关关系(P<0.01),且均对单位质量泥沙最大吸附量(Xm)和饱和吸附量(Cse)具有正效应,其中Al含量对该参数的影响更为显著。这说明泥沙对磷的吸附行为可能受到粒径和化学成分的共同影响。     

Chemical characterization and source identification/apportionment of fine and coarse air particles in Thessaloniki,Greece

The distribution of air particulate mass and selected particle components (trace elements and polycyclic aromatic hydrocarbons (PAHs)) in the fine and the coarse size fractions was investigated at a traffic-impacted urban site in Thessaloniki, Greece. 76±6% on average of the total ambient aerosol mass was distributed in the fine size fraction. Fine-sized trace elemental fractions ranged between 51% for Fe and 95% for Zn, while those of PAHs were between 95% and 99%. A significant seasonal effect was observed for the size distribution of aerosol mass, with a shift to larger fine fractions in winter. Similar seasonal trend was exhibited by PAHs, whereas larger fine fractions in summer were shown by trace elements. The compositional signatures of fine and coarse particle fractions were compared to that of local paved-road dust. A strong correlation was found between coarse particles and road dust suggesting strong contribution of resuspended road dust to the coarse particles. A multivariate receptor model (multiple regression on absolute principal component scores) was applied on separate fine and coarse aerosol data for source identification and apportionment. Results demonstrated that the largest contribution to fine-sized aerosol is traffic (38%) followed by road dust (28%), while road dust clearly dominated the coarse size fraction (57%).     

Evaluation of impacts of soil fractions on phenanthrene sorption

Phenanthrene sorption to soils and soil fractions was investigated using two contrasting soils with different clay mineral and organic carbon (OC) contents in an attempt to evaluate the contribution of each soil fraction to phenanthrene sorption and the applicability of the carbon-normalized distribution constant (K(OC)) in soils. Sorbents were characterized using surface analysis, solid-state (13)C NMR analysis, and glass transition temperature (T(g)) analysis to gain a insight into the chemical nature of OC in soils. Dissolved organic carbon (DOC) in the soil solution impeded the phenanthrene sorption, while humins accounted for the predominant phenanthrene sorption in soils. The contribution of OC to phenanthrene sorption in soil would be overestimated if only a K(OC)-approach was adopted, since clay minerals could account for much of the sorption, especially when OC was low in soils. Nitrogen gas was shown to be inappropriate for probing non-polar sorption capacity. The results obtained highlight the importance of clay minerals in governing the sorption of phenanthrene in soil, and emphasize the inapplicability of the carbon-normalized distribution coefficient K(OC) in soils.     

Sorption of 3,4-dichloroaniline on four contrasting Greek agricultural soils and the effect of liming

Sorption of 3,4-dichloroaniline (3,4-DCA) on four typical Greek agricultural soils, with distinct texture, organic matter content and cation exchange capacities, was compared by using sorption isotherms and the parameters calculated from the fitted Freundlich equations. The sorption process of 3,4-DCA to the soil was completed within 48–72 h. The 3,4-DCA sorption on all soils was well described by the Freundlich equation and all sorption isotherms were of the L-type. The sandy clay loam soil with the highest organic matter content and a slightly acidic pH was the most sorptive, whereas the two other soil types, a high organic matter and neutral pH clay and a low organic matter and acidic loam, had an intermediate sorption capacity. A typical calcareous soil with low organic matter had the lowest sorption capacity which was only slightly higher than that of river sand. The 3,4-DCA sorption correlated best to soil organic matter content and not to clay content or cation exchange capacity, indicating the primary role of organic matter. The distribution coefficient (K _d) decreased with increasing initial 3,4-DCA concentration and the reduction was most pronounced with the highly sorptive sandy clay loam soil, suggesting that the available sorption sites of the soils are not unlimited. Liming of the two acidic soils (the sandy clay loam and the loam) raised their pH (from 6.2 and 5.3, respectively) to 7.8 and reduced their sorption capacity by about 50 %, indicating that soil pH may be the second in importance factor (after organic matter) determining 3,4-DCA sorption.     

Sorption of 3,4-dichloroaniline on four contrasting Greek agricultural soils and the effect of liming

Sorption of 3,4-dichloroaniline (3,4-DCA) on four typical Greek agricultural soils, with distinct texture, organic matter content and cation exchange capacities, was compared by using sorption isotherms and the parameters calculated from the fitted Freundlich equations. The sorption process of 3,4-DCA to the soil was completed within 48-72 h. The 3,4-DCA sorption on all soils was well described by the Freundlich equation and all sorption isotherms were of the L-type. The sandy clay loam soil with the highest organic matter content and a slightly acidic pH was the most sorptive, whereas the two other soil types, a high organic matter and neutral pH clay and a low organic matter and acidic loam, had an intermediate sorption capacity. A typical calcareous soil with low organic matter had the lowest sorption capacity which was only slightly higher than that of river sand. The 3,4-DCA sorption correlated best to soil organic matter content and not to clay content or cation exchange capacity, indicating the primary role of organic matter. The distribution coefficient (K(d)) decreased with increasing initial 3,4-DCA concentration and the reduction was most pronounced with the highly sorptive sandy clay loam soil, suggesting that the available sorption sites of the soils are not unlimited. Liming of the two acidic soils (the sandy clay loam and the loam) raised their pH (from 6.2 and 5.3, respectively) to 7.8 and reduced their sorption capacity by about 50 %, indicating that soil pH may be the second in importance factor (after organic matter) determining 3,4-DCA sorption.     

Paraquat adsorption, degradation, and remobilization in tropical soils of Thailand

Paraquat adsorption, degradation, and remobilization were investigated in representative tropical soils of Yom River Basin, Thailand. Adsorption of paraquat in eight soil samples using batch equilibration techniques indicated that adsorption depended on soil characteristics, including exchangeable basic cations and iron content. Multiple regression analysis indicated significant contribution of exchangeable calcium percentage (ECP), total iron content (TFe) and exchangeable sodium percentage (ESP) to paraquat sorption (Q). ESP and TFe were significant at all adsorption stages, whereas ESP was significant only at the initial stage of paraquat adsorption. Adsorption studies using two soils representing clay and sandy loam textures showed that paraquat adsorption followed the Freundlich model, exhibiting a nonlinear sorption curve. Paraquat adsorption was higher in the clay soil compared to the sandy loam soil with Kf values of 787 and 18, respectively. Desorption was low with 0.04 to 0.17% and 0.80 to 5.83% desorbed in clay and sandy loam soil, respectively, indicating some hysteresis effect. Time-dependent paraquat adsorption fitted to the Elovich kinetic model indicated that diffusion was a rate-limiting process. Paraquat mobility and degradation studies conducted using both field and laboratory soil column experiments with clay soil showed low mobility of paraquat with accumulation only in the surface 0-5 cm layer under field conditions and in the 0-1 cm layer in a laboratory soil column experiment. Degradation of paraquat in soil was faster under field conditions than at ambient laboratory conditions. The degradation rate followed a first-order kinetic model with the DT50 at 36-46 days and DT90 around 119-152 days.     

Sorption–desorption of imidacloprid onto a lacustrine Egyptian soil and its clay and humic acid fractions

Sorption–desorption of the insecticide imidacloprid 1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine onto a lacustrine sandy clay loam Egyptian soil and its clay and humic acid (HA) fractions was investigated in 24-h batch equilibrium experiments. Imidacloprid (IMDA) sorption–desorption isotherms onto the three sorbents were found to belong to a non-linear L-type and were best described by the Freundlich model. The value of the IMDA adsorption distribution coefficient, Kd_ads, varied according to its initial concentration and was ranged 40–84 for HA, 14–58 for clay and 1.85–4.15 for bulk soil. Freundlich sorption coefficient, Kf_ads, values were 63.0, 39.7 and 4.0 for HA, clay and bulk soil, respectively. The normalized soil Koc value for imidacloprid sorption was ～800 indicating its slight mobility in soils. Nonlinear sorption isotherms were indicated by 1/n_ads values <1 for all sorbents. Values of the hysteresis index (H) were <1, indicating the irreversibility of imidacloprid sorption process with all tested sorbents. Gibbs free energy (ΔG) values indicated a spontaneous and physicosorption process for IMDA and a more favorable sorption to HA than clay and soil. In conclusion, although the humic acid fraction showed the highest capacity and affinity for imidacloprid sorption, the clay fraction contributed to approximately 95% of soil-sorbed insecticide. Clay and humic acid fractions were found to be the major two factors controlling IMDA sorption in soils. The slight mobility of IMDA in soils and the hysteresis phenomenon associated with the irreversibility of its sorption onto, mainly, clay and organic matter of soils make its leachability unlikely to occur.     

Differential pulmonary inflammation and in vitro cytotoxicity of size-fractionated fly ash particles from pulverized coal combustion

Exposure to airborne particulate matter (PM) has been associated with adverse health effects in humans. Pulmonary inflammatory responses were examined in CD1 mice after intratracheal instillation of 25 or 100 microg of ultrafine (< 0.2 microm), fine (< 2.5 microm), and coarse (> 2.5 microm) coal fly ash from a combusted Montana subbituminous coal, and of fine and coarse fractions from a combusted western Kentucky bituminous coal. After 18 hr, the lungs were lavaged and the bronchoalveolar fluid was assessed for cellular influx, biochemical markers, and pro-inflammatory cytokines. The responses were compared with saline and endotoxin as negative and positive controls, respectively. On an equal-mass basis, the ultrafine particles from combusted Montana coal induced a higher degree of neutrophil inflammation and cytokine levels than did the fine or coarse PM. The western Kentucky fine PM caused a moderate degree of inflammation and protein levels in bronchoalveolar fluid that were higher than the Montana fine PM. Coarse PM did not produce any significant effects. In vitro experiments with rat alveolar macrophages showed that of the particles tested, only the Montana ultrafine displayed significant cytotoxicity. It is concluded that fly ash toxicity is inversely related with particle size and is associated with increased sulfur and trace element content.     

Studies on the sorption and desorption characteristics of Zn(II) on the surface soils of nuclear power plant sites in India using a radiotracer technique

Zinc adsorption was studied in the soils of three nuclear power plant sites of India. 65Zn was used as a radiotracer to study the sorption characteristics of Zn(II). The sorption of zinc was determined at 25 and 45 degrees C at pH 7.8+/-0.2 in the solution of 0.01 M Ca(NO3)2 as supporting electrolyte. The sorption data was tested both in Freundlich and Langmuir isotherms and could be described satisfactorily. The effect of organic matter and other physico-chemical properties on the uptake of zinc was also studied in all the soil samples. The results showed that the cation exchange capacity, organic matter, pH and clay content were the main contributors to zinc sorption in these soils. The adsorption maximum was found to be higher in the soil on Kakarpara Atomic Power Plant sites soils having high organic matter and clay content. The zinc supply parameters of the soils are also discussed. In the desorption studies, the sequential extraction of the adsorbed zinc from soils showed that the diethylene triamine penta acetic acid extracted maximum amount of adsorbed zinc than CaCl2 and Mg(NO3)2. The zinc sorption on the soil and amount of zinc retention after extractants desorption shows a positively correlation with vermiculite and smectite mineral content present in the clay fraction of the soil. The amount desorbed by strong base (NaOH) and demineralised water was almost negligible from soils of all the sites, whereas the desorption by strong acid (HNO3) was 75-96% of the adsorbed zinc.     

Tylosin sorption to silty clay loam soils, swine manure, and sand

The objectives of this study were to assess sorption and desorption of tylosin, a macrolide antimicrobial chemical used in swine, cattle, and poultry production, in three silty clay loam soils of South Dakota and compare soil sorption to sand and manure sorption. The silty clay loam soils, from a toposequence in eastern South Dakota, standardized sand samples, and swine manure were used in 24-h batch sorption studies with tylosin concentrations ranging from 25 to 232 micro mole/L. Desorption from soil was conducted over a four-day period. Partition coefficients, based on the Freundlich isotherm (K(f)) or K(d) values, were calculated. K(f) values for the silty clay loams were similar, not influenced by landscape position, and averaged 1,350 with isotherm slopes ranging from 0.85 to 0.93. K(f) values for sand were dependent on solution/sand ratios and pH, ranging from 1.4 to 25.1. K(d) values of manure were dependent on the solution type and ranged from 840 L/kg with urine to about 175 L/kg when sorbed from water. Desorption of tylosin from each soil over the four-day period was < 0.2% of the amount added. The soils' high K(f) values and low desorption amounts suggest that once tylosin is in these soils, leaching to lower depths may not occur. However, this does not preclude runoff with soil eroded particles. If tylosin reaches a sand aquifer, through bypass flow or other mechanism(s), movement in the aquifer most likely would occur.     

Sorption of fipronil and its metabolites on soils from South Australia

This paper reports on the sorption of fipronil [(+/-)-5-amino-1-(2,6-dichloro-alpha,alpha,alpha-trifluoro-p-tolyl)-4-trifluoromethyl-sulfinylpyrazole-3-carbonitrile] and its two main metabolites, desulfynil and sulfide derivatives on a range of soils from South Australia. The Freundlich sorption coefficient (Kf) values for fipronil on the soils ranged from 1.94 to 4.84 using a 5% acetonitrile/water mixture as the soil solution. Its two metabolites had a higher sorption affinity for soils, with Kf values ranging from 11.09 to 23.49 for the sulfide derivative and from 4.70 to 11.77 for the desulfynil derivative. Their sorption coefficients were found to be better related to the soil organic carbon than clay content. The presence of cosolvents in soil solutions had a significant influence on the sorption of fipronil. The Freundlich sorption coefficients showed a log linear relationship with the fractions of both acetonitrile and methanol in solutions. The sorption coefficient of fipronil on Turretfield soil in the aqueous solution was estimated to be from 13.80 to 19.19. Methanol had less effect on the sorption of fipronil than acetonitrile. The Kd values for fipronil on the eight soils using a 5% methanol/water mixture were from 5.34 to 13.85, which reflect more closely the sorption in the aqueous solution. The average Koc value for fipronil on the eight South Australian soils was calculated to be 825+/-214.     

Overall dry deposition velocities of trace elements measured at harbor and traffic site in central Taiwan

For reasonable and convenient assessments of the characteristics of the dry deposition velocities between Taichung harbor site and Wuchi town site in central Taiwan, the overall dry deposition velocities of several metallic elements were calculated as the particulate diameter (D(p)) distributions of large particles (D(p) > 10 microm), coarse particles (10 microm < D(p) < 2.5 microm), and fine particles (D(p) < 2.5 microm) based on the ambient measurements during March-December of 2004. In this work, the dry deposition fluxes showed the higher correlation with coarse particle concentrations than large particle concentrations; however, the least well correlation was observed between the dry deposition fluxes and the fine particle concentrations. The calculated best-fit overall dry deposition velocities obtained using coarse particle concentrations varied from approximately 0.2 cm s(-1) for Cr to 1.5 cm s(-1) for Pb and 0.2 cm s(-1) for Fe to 2.6 cm s(-1) for Pb at Taichung harbor and Wuchi town site, respectively. In general, the crustal elements had higher deposition velocities than anthropogenic elements. In addition, overall dry deposition velocities for crustal elements were higher in Wuchi town site than in Taichung harbor site. The results identified the dry deposition flux was mainly contributed from large and coarse particles due to their high deposition velocities. The results also indicated that the best approach to estimate overall dry deposition was by depending on the characteristics of particles with diameters larger than 2.5 microm.     

Sorption of cobalt and nickel on anaerobic granular sludges: isotherms and sequential extraction

The objective of this study was to investigate the sorption capacity and the fractionation of sorbed nickel and cobalt onto anaerobic granular sludges. Two different anaerobic granular sludges (non-fed, pH=7) were loaded with nickel and cobalt in adsorption experiments (monometal and competitive conditions). The combination of sequential extraction with the sorption isotherm analysis allowed the assessment of the sorption capacity of individual fractions present in the anaerobic granular sludges. The operational fractionation of the sorbed heavy metals was determined using a modified Tessier sequential extraction procedure. The sorption characteristics of each extracted fraction (exchangeable, carbonates, organic matter/sulfides and residual fractions) fitted well to the Langmuir model. The organic matter/sulfides fraction showed the highest affinity for cobalt and nickel in both sludges investigated compared to the other operationally defined fractions. The presence of iron negatively affected cobalt and nickel accumulation in this organic matter/sulfides fraction. The trace metals-iron sulfide interactions are likely to be the key process in controlling the distribution of cobalt and nickel during sorption onto non-fed methanogenic granules due to the high affinity of iron sulfides towards the metals studied.     

Size distribution of airborne particulate matter and associated heavy metals in the roadside environment

The size distributions of airborne particulate matter (PM) and associated heavy metals Pb, Cd, Ni, Cr, V, Mn, Cu and Fe in different inhalable fractions (< 0.8 microm, 0.8-1.3 microm, 1.3-2.7 microm, 2.7-6.7 microm and > 6.7 microm) were determined at a traffic-orientated urban site in the city of Thessaloniki, northern Greece. The airborne PM displayed a bimodal distribution with most of the mass (52%) contained in the submicron size range (< 0.8 microm) and an additional minor mode (20%) in the coarse size fraction (> 6.7 microm). Characteristic size distributions of heavy metals allowed identification of three main behavioral types: (a) metals whose mass was resided mainly within the accumulation mode (Pb,Cd), (b) those which were distributed between fine, intermediate and coarse modes (Ni,Cu,Mn), and (c) those which were mainly found within particles larger than 2.7 microm in diameter (Fe). The mean mass median aerodynamic diameter (MMAD) of PM was found at 0.85+/-0.71 microm, while the mean MMADs of heavy metals followed the order Pb (0.96 +/- 0.71 microm) < Cd (1.14 +/- 0.82 microm) < V (1.38 +/- 0.63 microm) < Ni (1.45 +/- 0.88 microm) < Cu (2.04 +/- 0.77 microm) < Mn (2.61 +/- 1.23 microm) < Cr (2.91 +/- 1.40 microm) < Fe (3.82 +/- 0.88 microm). The measured distributions are believed to result from a combination of processes including local anthropogenic and natural sources, such as traffic, industrial emissions and resuspension of road dust.     

Paraquat Adsorption,Degradation, and Remobilization in Tropical Soils of Thailand

Paraquat adsorption, degradation, and remobilization were investigated in representative tropical soils of Yom River Basin, Thailand. Adsorption of paraquat in eight soil samples using batch equilibration techniques indicated that adsorption depended on soil characteristics, including exchangeable basic cations and iron content. Multiple regression analysis indicated significant contribution of exchangeable calcium percentage (ECP), total iron content (TFe) and exchangeable sodium percentage (ESP) to paraquat sorption (Q). ESP and TFe were significant at all adsorption stages, whereas ESP was significant only at the initial stage of paraquat adsorption. Adsorption studies using two soils representing clay and sandy loam textures showed that paraquat adsorption followed the Freundlich model, exhibiting a nonlinear sorption curve. Paraquat adsorption was higher in the clay soil compared to the sandy loam soil with K _f values of 787 and 18, respectively. Desorption was low with 0.04 to 0.17% and 0.80 to 5.83% desorbed in clay and sandy loam soil, respectively, indicating some hysteresis effect. Time-dependent paraquat adsorption fitted to the Elovich kinetic model indicated that diffusion was a rate-limiting process. Paraquat mobility and degradation studies conducted using both field and laboratory soil column experiments with clay soil showed low mobility of paraquat with accumulation only in the surface 0–5 cm layer under field conditions and in the 0–1 cm layer in a laboratory soil column experiment. Degradation of paraquat in soil was faster under field conditions than at ambient laboratory conditions. The degradation rate followed a first-order kinetic model with the DT₅₀ at 36–46 days and DT₉₀ around 119–152 days.     

Sorption of pentachlorophenol on surficial sediments: the roles of metal oxides and organic materials with co-existed copper present

The sorption characteristics of pentachlorophenol (PCP) in the surficial sediments were investigated using a selective extraction procedure. The results show that the Gamma(max) of PCP sorption decreased from 1.60mumolg(-1) to 0.69mumolg(-1) by approximately 60% after selective removal of organic materials from the sediments. The sorption of PCP in the sediments after selective removal of Mn oxides increased nearly up to 600% (from 1.60mumolg(-1) to 11.11mumolg(-1)) and, to a less degree, the PCP sorption in the sediments after simultaneous removal of Fe/Mn oxides (Gamma(max)=3.53mumolg(-1)). The analysis of the data using an additional model indicates that the contribution of Mn oxides to PCP sorption was negative, and Fe oxides and organic materials both have greater potential for sorption of PCP with less contribution from residues including Mn and Fe oxides in the residual fractions determined by a sequential extraction procedure and clay and silicate minerals. The differences in the decreased degrees of PCP sorption with increasing of Cu suggest that competition between Cu and PCP for sorption sites mainly takes place on Fe oxides.     

Long-term tillage effects on soil metolachlor sorption and desorption behavior

Sorption and desorption are two important processes that influence the amount of pesticides retained by soils. However, the detailed sorption mechanisms as influenced by soil tillage management are unclear. This study examined the sorption and desorption characteristics of metolachlor [2-chloro-N-(2-ethyl-6-methyphenyl)-N-(2-methoxy-1-methylethyl)-acetamide] using the soil samples collected from the long-term conservation tillage (CnT) and conventional tillage (CT) research plots established in 1979 in Darlinton, SC. Humic acid (HA) and humin were extracted from the soils and used in the sorption experiments along with the whole soil samples. The sorption experiments were conducted using a batch-equilibration method. Three sequential desorption rinses were carried out following the sorption experiments. By comparing metolachlor sorption and desorption results we observed hysteresis for all soil samples and their organic matter fractions. Sorption nonlinearity (N) and hysteresis were dependent on the structure and composition of soil organic matter (SOM), e.g., Freundlich isotherm exponents (N) of HA and humin from CnT were higher than those of CT treatment, which may be related to high aromaticity of SOM fractions in CT treatment. Sorption capacity (K'f) was positively correlated with soil organic carbon (SOC) content. These results show that long-term tillage management can greatly affect metolachlor sorption and desorption behavior probably by qualitative differences in the structural characteristics of the humic substances.     

The effects of particle size, organic matter content, crop residues and dissolved organic matter on the sorption kinetics of atrazine and isoproturon by clay soil

Reliable predictions of the fate and behaviour of pesticides in soils is dependent on the use of accurate ‘equilibrium’ sorption constants and/or rate coefficients. However, the sensitivity of these parameters to changes in the physicochemical characteristics of soil solids and interstitial solutions remains poorly understood. Here, we investigate the effects of soil organic matter content, particle size distribution, dissolved organic matter and the presence of crop residues (wheat straw and ash) on the sorption of the herbicides atrazine and isoproturon by a clay soil. Sorption K_d's derived from batch ‘equilibrium’ studies for both atrazine and isoproturon by <2 mm clay soil were approximately 3.5 L/kg. The similarity of K_oc's for isoproturon sorption by the <2 mm clay soil and <2 mm clay soil oxidised with hydrogen peroxide suggested that the sorption of this herbicide was strongly influenced by soil organic matter. By contrast, K_oc's for atrazine sorption by oxidised soil were three times greater than those for <2 mm soil, indicating that the soil mineral components might have affected sorption of this herbicide. No significant differences between the sorption of either herbicide by <2 mm clay soil and (i) <250 μm clay soil, (ii) clay soil mixed with wheat straw or ash at ratios similar to those observed under field conditions, (iii) <2 mm clay soil in the presence of dissolved organic matter as opposed to organic free water, were observed.