Overall elemental dry deposition velocities measured around Lake Michigan

Overall dry deposition velocities of several elements were determined by dividing measured fluxes by measured airborne concentrations in different particle size ranges. The dry deposition measurements were made with a smooth surrogate surface on an automated dry deposition sampler (Eagle II) and the ambient particle concentrations were measured with a dichotomous sampler. These long-term measurements were made in Chicago, IL, South Haven, MI, and Sleeping Bear Dunes, MI, from December 1993 through October 1995 as part of the Lake Michigan Mass Balance Study. In general, the dry deposition fluxes of elements were highly correlated with coarse particle concentrations, slightly less well correlated with total particle concentrations, and least well correlated with fine particle concentrations. The calculated overall dry deposition velocities obtained using coarse particle concentrations varied from approximately 12 cm s⁻¹ for Mg in Chicago to 0.2 cm s⁻¹ for some primarily anthropogenic metals at the more remote sites. The velocities calculated using total particle concentrations were slightly lower. The crustal elements (Mg, Al, and Mn) had higher deposition velocities than anthropogenic elements (V, Cr, Cu, Zn, Mo, Ba and Pb). For crustal elements, overall dry deposition velocities were higher in Chicago than at the other sites.     

Atmospheric dry deposition fluxes of trace elements measured in Bursa, Turkey

Trace element dry deposition fluxes were measured using a smooth, greased, knife-edge surrogate surface (KSS) holding greased Mylar strips in Bursa, Turkey. Sampling program was conducted between October 2002 and June 2003 and 46 dry deposition samples were collected. The average fluxes of crustal metals (Mg, Ca, and Fe) were one to four orders of magnitude higher than the fluxes of anthropogenic metals. Trace element fluxes ranged from 3 (Cd) to 24,230 (Ca) microg m(-2) d(-1). The average trace element dry deposition fluxes measured in this study were similar to those measured in other urban areas. In addition, ambient air samples were also collected simultaneously with flux samples and concentrations of trace elements, collected with a TSP sampler, were between 0.7 and 4900 ng m(-3) for Cd and Ca, respectively. The overall trace element dry deposition velocities, calculated by dividing the fluxes to the particle phase concentrations ranged from 2.3+/-1.7 cm s(-1) (Pb) to 11.1+/-6.4 cm s(-1) (Ni). These values are in good agreement with the values calculated using similar techniques. The anthropogenic and crustal contributions were estimated by employing enrichment factors (EFs) calculated relative to the average crustal composition. Low EFs for dry deposition samples were calculated. This is probably due to contamination of local dust and its important contribution to the collected samples.     

Determination of atmospheric nitrate particulate size distribution and dry deposition velocity for three distinct areas

In this study, both atmospheric particulates and dry deposited particulates were collected at a highway intersection, coastal location and suburban area in Taichung, Taiwan for the characterization of nitrate containing particulates (NCPs) in size distribution and dynamic properties. Collected particulates were placed in contact with nitron (C20H16N4) to form distinctive products of NCPs, which were examined by a SEM. For total atmospheric particulates, the sum of NCP and non-nitrate containing particulate (NNCP), the average shape factor values are 1.69, 1.49, and 1.36 for the highway intersection, coastal area and suburban area, respectively. The calculated shape factors show no significant differences with sizes. Dry deposition fluxes and atmospheric concentrations at various size ranges were estimated. The mass distributed in fine particle range (相似文献   

Study of particulates and metallic elements at a farm sampling site in central Taiwan

The total suspended particle (TSP) concentration, dry deposition and wind speed were measured with a PS-1 sampler, a dry deposition plate and a Weather Monitor II (#7440), respectively, at the Experimental Farm of Thunghai University in Taiwan. Taiching Industrial Park, Taichung Cong Road (traffic) and a hospital incinerator are close to the sampling site. The sampling time was from August 2001 to December 2001. The average dry deposition flux, the TSP concentration, dry deposition velocities, average wind speed and maximum wind speed were recorded as 617.7 ± 281.4 mg/day/m2, 117.5 ± 17.6 μg/m3, 5.9 ± 2.2 cm/s, 2.7 ± 1.3 m/s and 7.6 ± 2.3 m/s, respectively, at this sampling site. Good correlation coefficients (R) of the TSP concentration and the dry deposition flux with wind speed were found, with values of 0.46 and 0.50, respectively. The concentrations and dry deposition of the total metallic elements were also obtained. The results indicated that the concentrations of anthropogenic elements (Pb, Mn, Cd, Ni, Cr and Zn) were mostly higher than those obtained in other studies around the world. The average dry deposition fluxes and TSP concentrations for Zn and Pb were 0.45 and 0.42, respectively. The same phenomenon was also observed for Fe and Mg (R = 0.59 and 0.65). The results indicate that these elements were all coming from the same emission sources at the farm sampling site.     

Particulates and Metallic Elements Monitoring at Two Sampling Sites (Harbor,Airport) in Taiwan

This study characterized the dry deposition flux and dry deposition velocity (Vd) of metallic elements attached on particulate matter. Specifically, large particles (>10 μm), coarse particles (10 μm～2.5 μm), and fine particles (<2.5 μm) were studied at the Gong Ming Junior High School (Taichung Airport) and Taichung Harbor sampling sites in central Taiwan. Ambient air samples were collected to determine total suspended particulate matter (TSP), dry deposition plate (DDP), Vd, coarse particulate matter (PM_2.5–10) and fine particulate matter (PM_2.5), and metallic elements concentrations at the Airport and Taichung Harbor sites between June 17, 2013, and November 14, 2013. The results revealed that the average TSP, DDP, Vd, PM_2.5–10, and PM_2.5 particulate at the Airport were 54.55 (μg/m³), 902.25 (μg/m²-min), 17.11 (m/sec), 0.003 (μg/m³), and 0.010 (μg/m³), respectively; while these values at Taichung Harbor were 63.66 (μg/m³), 539.69 (μg/m²-min), 9.94 (m/sec), 0.003 (μg/m³), and 0.014 (μg/m³), respectively. In addition, the results showed that the average Cu and Pb concentrations were higher than Cr, Ni, and Cd for both the airport and harbor sampling sites. Furthermore, Cr, N, Cu, Cd, and Pb had the highest average concentrations versus those reported for other study areas, with one exception: The results obtained in Kacanik, Kosovo, during 2005. The average metallic elements concentrations order was Cu > Pb > Cr > Ni > Cd.     

Concentration, size distribution, and dry deposition rate of particle-associated metals in the Los Angeles region

Daily averaged atmospheric concentrations and dry deposition fluxes of particulate metals were measured seasonally at six urban sites and one non-urban coastal site in the Los Angeles region using a conventional total suspended particulate matter (TSP) filter, surrogate surface deposition plates, and a Noll Rotary Impactor (NRI), which provides information about particle size distribution in four size ranges above 6 μm. With the exception of the non-urban site, particulate metal concentrations and deposition fluxes were remarkably uniform spatially and temporally. At all sites there were significant metal concentrations on particles greater than 10 μm, a commonly used upper limit for many air quality monitoring studies, and these large particles were estimated to be responsible for most of the deposited mass of metals. Annual averaged values of deposition rates measured with a surrogate surface were in good agreement with values estimated using theoretical deposition velocities in conjunction with measured size-segregated particle concentrations. Image analysis of particles deposited on NRI stage A, which collects all particles greater than 6 μm, indicated nighttime metal concentrations and deposition at the non-urban coastal site was higher than in the day time due to offshore advection of urban air associated with the diurnal land breeze. Measured enrichments of crustal elements and metals were correlated, indicating efficient mixing of natural and anthropogenic material from different sources, hypothesized to be the result of cyclical resuspension and deposition of dust by moving vehicles and wind.     

Dry deposition, ionic species measured and source interpretation during seasonal cycle at offshore areas near Taiwan Strait

The characterization for water-soluble species of total suspended particulate (TSP), dry deposition flux, and dry deposition velocity (V(d)) were studied at Taichung Harbor (TH) and Wuchi traffic sampling sites at offshore sampling site near Taiwan Strait of central Taiwan during March 2004-January 2005. The average concentrations of TSP and dry deposition flux at the TH sampling site were higher than at the WT sampling site during the sampling period. The samples collected were analyzed by a ion chromatography (DIONEX-100) for the ionic species (Cl(-), SO(4)(2-), NO(3)(-), NH(4)(+), Na(+), Ca(2+), and Mg(2+)) analysis. The dominant ionic species for TSP are SO(4)(2-), NO(3)(-), and NH(4)(+) of the total mass of the inorganic ions at both sampling sites. In addition, the results indicated that the NH(4)(+), NO(3)(-) and SO(4)(2-) showed higher concentrations in winter and lower in summer for both TH and Wuchi sampling sites. Statistical methods such as correlation coefficient and principal component analysis were also used to identify the possible pollutant source.     

Ambient concentrations and dry deposition fluxes of trace elements in Izmir,Turkey

Dry deposition samples were collected using a smooth surrogate surface at the Kaynaklar Campus of the Dokuz Eylul University in Izmir, Turkey. Concurrently ambient aerosol samples were collected. All samples were analyzed for anthropogenic and crustal trace elements. The average trace element concentrations and fluxes measured in this study were generally higher than those reported previously for urban and rural areas. The contribution of local terrestrial and anthropogenic sources were also investigated using enrichment factors (EFs) calculated relative to the local soil. Relatively lower EFs for ambient samples and high ambient concentrations indicated that the local soil was polluted and contributed significantly to ambient trace element concentrations. Deposition samples had higher EFs than the air samples. The EF sequences of trace elements were also different for deposition and ambient samples, probably due to the fact they have different mass median diameters and deposition velocities. The overall dry deposition velocities for trace elements calculated by dividing the particulate fluxes measured with the surrogate surfaces by ambient concentrations ranged from 0.6 (Al) to 6.2 cm s⁻¹ (Fe). The agreement between the experimental dry deposition velocities determined in this study and the previously reported ones using similar techniques for trace elements was good.     

Metallic elements in particulates released during incense-burning at Tzu Yun Yen temple, Taichung, Taiwan

Concentrations of ambient suspended particulates were measured at Tzu Yun Yen temple (120°, 34′ 10”E; 24°, 16′, 12”N), using a Universal sampler and dry deposition plates. The temple is a characteristic incense-burning and semi-open sampling site. PM_2.5 concentrations for Period 1 (average 901μg/m3) were higher than those for Period 2 (average 701μg/m3). Results for average PM_2.5-10concentrations showed equal distributions in Period 1 and Period 2. Average ratios of PM_2.5/ PM₁₀ were higher in Period 1 (74%) than Period 2 (71%). In addition, the suspended particulate (PM₁₀) elements concentrations during Zhong Yuan Jie, and the first and 15th days of nong li for each month (Chinese lunar calendar) were all higher than during non-Zhong Yuan Jie and non-first and non-15th days. Furthermore, the dry deposition velocities of manganese in fine particulates (PM_2.5) and suspended particulates (PM₁₀) were 1.43 and 0.751cm/s, respectively, and the dry deposition velocities of cadmium in fine particulates (PM_2.5) and suspended particulates (PM₁₀) were 1.86 and 0.991cm/s, respectively.     

Comparison of particulate mass, chemical species for urban, suburban and rural areas in central Taiwan, Taichung

Aerosol samples for PM2.5, PM(2.5-10) and TSP were collected from June to September 1998 and from February to March 1999 in central Taiwan. Ion chromatography was used to analyze the acidic anions: sulfate, nitrate and chloride in the Universal samples. The ratios of fine particle concentrations to coarse particle concentrations displayed that the fine particle concentrations are almost greater than that of coarse particle concentrations in Taichung area. The average concentrations of PM2.5, PM(2.5-10) and TSP in urban sites are higher than in suburban and rural sites at both daytime and night-time. Chloride dominated in the coarse mode in daytime and in fine mode in night-time. Nitrate can be found in both the coarse and fine modes. Sulfate dominated in fine mode in both daytime and night-time.     

Effects of open burning of rice straw on concentrations of atmospheric polycyclic aromatic hydrocarbons in central Taiwan

The sizes and concentrations of 21 atmospheric polycyclic aromatic hydrocarbons (PAHs) were measured at Jhu-Shan (a rural site) and Sin-Gang (a town site) in central Taiwan in October and December 2005. Air samples were collected using semi-volatile sampling trains (PS-1 sampler) over 16 days for rice-straw burning and nonburning periods. These samples were then analyzed using a gas chromatograph with a flame-ionization detector (GC/FID). Particle-size distributions in the particulate phase show a bimode, peaking at 0.32-0.56 microm and 3.2-5.6 microm at the two sites during the nonburning period. During the burning period, peaks also appeared at 0.32-0.56 microm and 3.2-5.6 microm at Jhu-Shan, with the accumulation mode (particle size between 0.1 and 3.2 microm) accounting for approximately 74.1% of total particle mass. The peaks at 0.18-0.32 microm and 1.8-3.2 microm at Shin-Gang had an accumulation mode accounting for approximately 70.1% of total particle mass. The mass median diameter (MMD) of 3.99-4.35 microm in the particulate phase suggested that rice-straw burning generated increased numbers of coarse particles. The concentrations of total PAHs (sum of 21 gases + particles) at the Jhu-Shan site (Sin-Gang site) were 522.9 +/- 111.4 ng/ml (572.0 +/- 91.0 ng/ml) and 330.1 +/- 17.0 ng/ml (or 427.5 +/- 108.0 ng/ml) during burning and nonburning periods, respectively, accounting for a roughly 58% (or 34%) increase in the concentrations of total PAHs due to rice-straw burning. On average, low-weight PAHs (about 87.0%) represent the largest proportion of total PAHs, followed by medium-weight PAHs (7.1%), and high-weight PAHs (5.9%). Combustion-related PAHs during burning periods were 1.54-2.57 times higher than those during nonburning periods. The results of principal component analysis (PCA)/absolute principal component scores (APCS) suggest that the primary pollution sources at the two sites are similar and include vehicle exhaust, coal/wood combustion, incense burning, and incineration emissions. Open burning of rice straw was estimated to contribute approximately 5.0-33.5% to the total atmospheric PAHs at the two sites.     

The study of fine and coarse particles, and metallic elements for the daytime and night-time in a suburban area of central Taiwan, Taichung

Daily average concentrations of fine and coarse particulates, and TSP samples have been measured simultaneously at daytime and night-time periods by using Universal and PS-1 sampler in a suburban area of central Taiwan from June to August 1998. The samples were analyzed by atomic absorption spectrometry to determine the fine and coarse particulate concentrations of metallic elements (Ca, Fe, Mn, Pb, Cu, Zn and Cr). The concentration of PM2.5 and TSP showed a decreased trend for the daytime period. The fine particle concentrations were about two times as that of coarse particulate concentrations. The averaged fine particulate concentrations at daytime are higher than at night-time. Ca and Fe were mostly in the coarse particulate mode. The correlation coefficients were 0.63 and 0.69 for elements Ca and Fe in the coarse particle mode for day and night periods. Pb showed a similar distribution ratio with Mn for the fine to coarse particle ratios at both day and night period. Pb and Mn are highly correlated for the day (R = 0.78) and night period (R = 0.61) at particle size <2.5 microm. Cu and Zn were mainly in fine particles at both day and night period. Fe and Ca consist of the major parts of all the elements. Elemental Mn is the lowest among the rest of the heavy metals.     

Particle-bound PAH content in ambient air

Ambient air samples from a traffic intersection, an urban site and a petrochemical-industrial site (PCI) were collected by using several dry deposition plates, two Microorifice uniform deposited impactors (MOUDIs), one Noll Rotary Impactor (NRI) and several PS-1 (General Metal Work) samplers from March 1994 to June 1995 in southern Taiwan, to characterize the atmospheric particle-bound PAH content of these three areas. Twenty-one individual polycyclic aromatic hydrocarbons (PAHs) were analyzed primarily by using a gas chromatograph/mass spectrometer (GC/MS). In general, the sub-micron particles have a higher PAH content. This is due to the fact that soot from combustion sources consists primarily of fine particles and has a high PAH content. In addition, a smaller particle has a higher specific surface area and therefore may contain more organic carbon, which allows for more PAH adsorption. For a particle size range between 0.31 and 3.2 microm, both Urban/Traffic and PCI/Traffic ratios of particle-bound total-PAH content have the lowest values, ranging from 0.25 to 0.28 (mean = 0.26) and from 0.07 to 0.13 (mean = 0.10), respectively. This indicates that, during the accumulation process, the PAH mass shifted from a particle phase to a gas phase, or the particles aggregated with lower PAH-content particles, resulting in a reduction in particle-bound PAH content. By using the particle size distribution data, the dry deposition model in this study can provide a good prediction for the PAH content of dry deposition materials. In general, lower molecular weight PAHs had a larger fraction of dry deposition flux contributed by the gas phase; for 2-ring PAH (50.4, 46.3 and 28.4%), 3-ring PAHs (15.2, 15.4 and 11.7%) and 4-ring PAHs (13.0, 3.60 and 5.01%) for the traffic intersection, urban and PCI sites, respectively. For higher molecular weight PAHs-5-ring, 6-ring and 7-ring PAHs-their cumulation fraction (F%) of dry deposition flux contributed by the gas phase was lower than 3.26%. At the traffic intersection, urban and PCI sites, the mass median diameter of dry deposition materials (MMD(F)) of individual PAHs was between 25.3 and 49.6 microm, between 27.6 and 43.9 microm, and between 19.1 and 41.9 microm, respectively. This is due to the fact that PAH dry-deposition primarily resulted from gravitational settling of the coarse particulates (> 10 microm).     

Sources and chemical composition of atmospheric fine and coarse particles in the Helsinki area

During April 1996–June 1997 size-segregated atmospheric aerosol particles were collected at an urban and a rural site in the Helsinki area by utilising virtual impactors (VI) and Berner low-pressure impactors (BLPI). In addition, VI samples were collected at a semi-urban site during October 1996–May 1997. The average PM_2.3 (fine particle) concentrations at the urban and rural sites were 11.8 and 8.4 μg/m³, and the PM_2.3−15 (coarse particle) concentrations were 12.8 and about 5 μg/m³, respectively. The difference in fine particle mass concentrations suggests that on average, more than one third of the fine mass at the urban site is of local origin. Evaporation of fine particle nitrate from the VI Teflon filters during sampling varied similarly at the three sites, the average evaporation being about 50–60%.The average fine particle concentrations of the chemical components (25 elements and 13 ions) appeared to be fairly similar at the three sites for most components, which suggests that despite the long-range transport, the local emissions of these components were relatively evenly distributed in the Helsinki area. Exceptions were the average fine particles Ba, Fe, Sb and V concentrations that were clearly highest at the urban site pointing to traffic (Ba, Fe, Sb) and to combustion of heavy fuel oil (V) as the likely local sources. The average coarse particle concentrations for most components were highest at the urban site and lowest at the rural site.Average chemical composition of fine particles was fairly similar at the urban and rural sites: non-analysed fraction (mainly carbonaceous material and water) 43% and 37%, sulphate 21% and 25%, crustal matter 12% and 13%, nitrate 12% and 11%, ammonium 9% and 10% and sea-salt 2.5% and 3.2%, respectively. At the semi-urban site also, the average fine particle composition was similar. At the urban site, the year round average composition of coarse particles was dominated by crustal matter (59%) and the non-analysed components (28%, mainly carbonaceous material and water), while the other contributions were much lower: sea-salt 7%, nitrate 4% and sulphate 2%. At the rural site, the coarse samples were collected in spring and summer and the percentage was clearly lower for crustal matter (37%) and sea-salt (3%) but higher for the not-analysed fraction (51%). At the semi-urban site, the average composition of coarse particles was nearly identical to that at the urban site.Correlations between the chemical components were calculated separately for fine and coarse particles. In urban fine particles sulphate, ammonium, Tl, oxalate and PM_2.3 mass correlated with each other and originated mainly from long-range transport. The sea-salt ions Na⁺, Cl⁻ and Mg²⁺ formed another group and still another group was formed by the organic anions oxalate, malonate, succinate, glutarate and methane sulphonate. Ni and V correlated strongly pointing to combustion of heavy fuel oil as the likely source. In addition, some groups with lower correlations were detected. At the rural and semi-urban sites, the correlating components were rather similar to those at the urban site, although differences were also observed.     

Source identification of atlanta aerosol by positive matrix factorization

Data characterizing daily integrated particulate matter (PM) samples collected at the Jefferson Street monitoring site in Atlanta, GA, were analyzed through the application of a bilinear positive matrix factorization (PMF) model. A total of 662 samples and 26 variables were used for fine particle (particles < or = 2.5 microm in aerodynamic diameter) samples (PM2.5), and 685 samples and 15 variables were used for coarse particle (particles between 2.5 and 10 microm in aerodynamic diameter) samples (PM10-2.5). Measured PM mass concentrations and compositional data were used as independent variables. To obtain the quantitative contributions for each source, the factors were normalized using PMF-apportioned mass concentrations. For fine particle data, eight sources were identified: SO4(2-) -rich secondary aerosol (56%), motor vehicle (22%), wood smoke (11%), NO(3-) -rich secondary aerosol (7%), mixed source of cement kiln and organic carbon (OC) (2%), airborne soil (1%), metal recycling facility (0.5%), and mixed source of bus station and metal processing (0.3%). The SO4(2-) -rich and NO(3-) -rich secondary aerosols were associated with NH(4+). The SO4(2-) -rich secondary aerosols also included OC. For the coarse particle data, five sources contributed to the observed mass: airborne soil (60%), NO(3-)-rich secondary aerosol (16%), SO4(2-) -rich secondary aerosol (12%), cement kiln (11%), and metal recycling facility (1%). Conditional probability functions were computed using surface wind data and identified mass contributions from each source. The results of this analysis agreed well with the locations of known local point sources.     

Dry deposition (downward, upward) concentration study of particulates and heavy metals during daytime, nighttime period at the traffic sampling site of Sha-Lu, Taiwan

Downward, upward dry deposition fluxes and total suspended particulate of particulate heavy metals (Fe, Pb, Zn, Cu, Mg and Mn) were measured in daytime and nighttime period in Sha-Lu, a small city in the central Taiwan during summer period of 2003. The results showed that the total suspended particulate concentrations of particulate mass in the daytime period (averaged 996.2 g/m3) were higher than in nighttime period (averaged 560.7 g/m3). And the downward dry deposition fluxes (averaged 54.07 g/m2s) were about two times as that of upward dry deposition fluxes (averaged 26.48 g/m2s) in the daytime period. Furthermore, the average downward dry deposition fluxes (averaged 26.22 g/m2s) were also about two times as that of upward dry deposition fluxes (averaged 12.11 g/m2s) in the nighttime period. In addition, the average downward dry deposition fluxes are greater than the upward dry deposition fluxes for all the heavy metals in either daytime or nighttime period. The proposed reasons are that the wind speed and concentration difference for daytime and nighttime period lead to these results at the traffic sampling site of central Taiwan. In addition, the deposition velocity for mass, heavy metals (Fe, Pb, Zn, Cu, Mg and Mn) during daytime and nighttime period were also calculated. The average daytime dry deposition velocity for downward particulate mass, upward particulate mass, Fe, Pb, Zn, Cu, Mg and Mn were 5.56, 2.66, 1.71, 0.18, 1.06, 0.24, 0.47 and 0.11 (cm/s), respectively. And the average nighttime dry deposition velocity for downward particulate mass, upward particulate mass, Fe, Pb, Zn, Cu, Mg and Mn were 4.70, 2.11, 1.66, 0.18, 0.86, 0.23, 0.32 and 0.07 (cm/s), respectively at traffic sampling site of central Taiwan.     

Metal distributions in soil receiving urban pavement runoff and snowmelt.

Wet and dry deposition of anthropogenic metals and particulates generated from urban and traffic activities can result in contamination of urban-land-use soils. These particulate residuals encompass a wide size gradation, from 1 to greater than 10 000 microm. This study hypothesized that such contamination of surficial soils can be analyzed and explained as a function of the soil/residual granulometry. This study analyzed the gradation-based physical characteristics for 10 urban transportation land-use sites with soil/residual complexes (SRCs) located throughout metropolitan Cincinnati, Ohio, and an urban residential reference site. Particle density (rho(s)) of SRCs ranged from 2.8 to 2.1 g/cm3, with the lower particle density associated with particles less than 100 microm. For each site, specific surface area generally increased with decreasing particle size, while the predominance of total surface area was associated with the coarser size fractions, except for the clayey glacial till reference site not influenced by traffic. Cumulative analysis for lead, copper, cadmium, and zinc associated with SRCs indicated that more than 50% of the metal mass was associated with particles greater than 250 microm, with more than 80% associated with particles greater than 106 microm. Study results are similar to rainfall-runoff and snowmelt distributions. Results provide guidance when considering potential fate and control of metals transported by urban drainage and are distributed across the SRC size gradation.     

Atmospheric deposition of organochlorine pesticides by precipitation in a coastal area

Wet deposition fluxes of organochlorine pesticides (OCPs) were determined for rain samples collected in a coastal area of Turkey. Seventeen precipitation samples were collected over a 1-year period from 2008 to 2009. Rainwater was accumulated at the beginning of rain events using real time monitoring. Atmospheric concentrations were also measured in parallel with deposition samples. Both atmospheric concentrations and deposition fluxes were determined as particle and gas phases. The particle phase and dissolved phase deposition fluxes were 794.26?±?756.70 ngm^?2 day^?1 and 800.77?±?672.63 ngm^?2 day^?1, respectively. The washout ratios for OCP compounds were calculated separately for the particle and dissolved phases using the atmospheric concentrations and rain concentrations. The minimum washout ratio for the particle phase was 2339.47 for Endrin aldehyde, whereas the maximum washout ratio was 497593.34 for Methoxychlor. The maximum washout ratio for the dissolved phase was 247523.89 for Endosulfan beta, whereas the minimum washout ratio was 10169.69 for p,p′-DDT. The dry deposition velocities ranged from 0.01 to 1.67 cms^?1. The partitioning of wet deposition between the particle and dissolved phases was 50 % in terms of total OCP deposition.     

Measurements and modelling of cloudwater deposition to moorland and forests

The objective of the study was to measure the size dependence of cloudwater deposition and associated average ionic fluxes to vegetated surfaces. Measurements were made over a forest canopy at Dunslair heights in south Scotland and a moorland site, Great Dun Fell, in northern England. Measurements were made using the gradient and eddy correlation techniques. Eddy correlation measurements were made using an ultrasonic anemometer, a Knollenberg forward scattering spectrometer probe (to measure liquid water fluxes and fluxes of droplets in 1 microm size intervals) and a GSI particulate volume monitor (to measure liquid-water fluxes). Measurements were made at Great Dun Fell of the size dependence of droplet deposition velocity, using the gradient technique with two Knollenberg probes. Simultaneous gradient and eddy correlation measurements were also made at Great Dun Fell of average cloud-water fluxes, together with chemical analysis of cloud water composition, using a continuous analysis system. At Dunslair Heights, eddy correlation measurements were made using both the Knollenberg and Gerber Scientific Instruments (GSI) probes, while simultaneous gradient measurements using two GSI probes were also attempted. Samples of cloud water were collected at Dunslair Heights, using passive string collectors for chemical analysis by ion chromatography. The major findings of the study were: 1. The droplet deposition velocities measured by the two techniques were similar. 2. The deposition velocities were a strong function of droplet size. Considerable resistance to deposition was evident for droplets of less than 5 microm radius. Deposition velocities for particles from about 6 to 8 microm exceeded those for momentum. 3. Except when the droplets were very small or the winds very light, bulk cloud-water deposition velocities were about 80% or more of the momentum deposition velocities to forests.     

Bulk deposition of polycyclic aromatic hydrocarbons (PAHs) in an industrial site of Turkey

Ambient air and deposition samples were collected in the period of July 2004-May 2005 in an industrial district of Bursa, Turkey and analyzed for polycyclic aromatic hydrocarbon (PAH) compounds. The overall average of fourteen bulk deposition fluxes for PAHs was 3300+/-5100 ng m(-2) d(-1). PAH depositions showed a seasonal variation and they were higher in winter months. This was probably due to increases in residential heating activities and decreases in atmospheric mixing layer levels. Ambient air samples, measured with a high volume air sampler, were collected from the same site. The average total concentration including gas and particulate phase was about 300+/-420 ng m(-3) and it was in the range of previously reported values. Some of the ambient air and bulk deposition samples were collected simultaneously in dry periods. Both concurrently measured values were used to calculate the dry deposition velocities whose overall average value was 0.45+/-0.35 cm s(-1).