Pattern of Hexa-Valent Chromium in Air Borne Respirable Dust Generated at Various Workplaces in Opencast Chromite Mines

The paper presents a study into air borne respirable dust (ARD) concentration at various workplaces in two open cast chromite mines of Sukinda chromite belt, India. One of these mines is mechanised and the other one is semi-mechanised. The study has been conducted in three phases and ARD concentration has been measured at various workplaces in both the mines. Apart from the determination of ARD concentration, the dust samples collected on filter papers were analysed for hexa-valent chromium by colorimetric method and Cr(VI) direct absorption measurement. In addition, the particle size ranges in ARD have been determined by using cascade impactor fitted onto high volume samplers and laser guided particle size analyser. The paper finally presents a comparison between ARD concentration vis-à-vis the presence of hexa-valent chromium concentration in collected samples of both mechanised and semi-mechanised mines.     

Submicrometer elemental carbon as a selective measure of diesel particulate matter in coal mines

A monitoring method for diesel particulate matter was published as Method 5040 by the National Institute for Occupational Safety and Health (NIOSH). Organic and elemental carbon are determined by the method, but elemental carbon (EC) is a better exposure measure. The US Mine Safety and Health Administration (MSHA) proposed use of NIOSH 5040 for compliance determinations in metal and nonmetal mines. MSHA also published a rulemaking for coal mines, but no exposure standard was provided. A standard based on particulate carbon is not considered practical because of coal dust interference. Interference may not be a problem if an appropriate size-selective sampler and EC exposure standard are employed. Submicrometer dust concentrations found in previous surveys of nondieselized, underground coal mines were relatively low. If a large fraction of the submicrometer dust is organic and mineral matter, submicrometer EC concentrations would be much lower than submicrometer mass concentrations. Laboratory and field results reported herein indicate the amount of EC contributed by submicrometer coal dust is minor. In a laboratory test, a submicrometer EC concentration of 31 microg m(-3) was found when sampling a respirable coal dust concentration over three times the US compliance limit (2 mg m(-3)). Laboratory results are consistent with surveys of nondieselized coal mines, where EC results ranged from below the method limit of detection to 18 microg m(-3) when size-selective samplers were used to collect dust fractions having particle diameters below 1.5 microm-submicrometer EC concentrations were approximate 7 microg m(-3). In dieselized mines, submicrometer EC concentrations are much higher.     

Evaluation of the SKC DPM cassette for monitoring diesel particulate matter in coal mines

In a previous study, the efficacy of commercial and prototype impactors for sampling diesel particulate matter (DPM) in coal mines was investigated. Laboratory and field samples were collected on quartz-fiber filters and analyzed for organic and elemental carbon. Coal dust contributed a minimal amount of elemental carbon when commercial cascade impactors and prototype impactors, designed by the University of Minnesota (UMN) and the US Bureau of Mines (BOM), were used to collect submicrometer dust fractions. Other impactors were not as effective at excluding coal dust. The impactors evaluated in that study were either not commercially available or were multi-stage, expensive, and difficult to use for personal measurements. A commercial version of the BOM impactor, called the DPM Cassette, was recently introduced by SKC. Tests were conducted to evaluate the performance of the DPM Cassette for measuring diesel-source elemental carbon in the presence of coal dust. Bituminous coals from three mines in two different coal provinces were examined. The dust particle diameters were small and the coal dust contained a high percentage of carbon, thereby giving a worst-case condition for non-anthracite coal mines. Results for the DPM Cassette were essentially identical to those obtained by the BOM impactors in a previous study. At a respirable coal dust concentration of 5.46 mg m(-3), which is 3.8 times the regulatory limit, the DPM Cassette collected only 34 microg m(-3) of coal-source elemental carbon.     

Uranium bioassay and radioactive dust measurements at some uranium processing sites in Egypt--health effects

The safety of radiation workers in the uranium mining industry requires close and continuous monitoring of their working conditions. In this study, external radiation surveillance, radioactive dust monitoring and the bioassay of uranium were carried out in some processing sites. As dust represents one of the most important sources of radiation exposure in mills and mines, dust monitoring and bioassays were performed for a sample of workers on the production lines. The concentration of uranium in air ranged from 22.6 x 10(-7) to 11.1 x 10(-5) Bq cm-3, and the exposure levels ranged from 1 to 80 microSv h-1. Laser fluorimetric determination of uranium in urine samples showed concentrations in the range 8.4-29.2 micrograms L-1. Renal function parameters, such as serum creatinine and urea, and hematological parameters were determined in an attempt to correlate them with radiation exposure and the health status of the workers. Urine specimens collected from workers at the ore crushing and separation site showed elevated concentrations of uranium (up to 29.2 micrograms L-1) and a strong correlation between these concentrations and the registered serum creatinine. The mean uranium excretion in the investigated group was more than 20 times the occupational exposure decision level for urine uranium of 0.8 microgram L-1.     

Evaluation of interference to conventional and real-time PCR for detection and quantification of fungi in dust

Advances in polymerase chain reaction (PCR) have permitted accurate, rapid and quantitative identification of microorganisms in pure cultures regardless of viability or culturability. In this study, a simple sample processing method was investigated for rapid identification and quantification of fungal spores from dust samples using both conventional and real-time PCR. The proposed method was evaluated for susceptibility to interference from environmental dust samples. Stachybotrys chartarum and Aspergillus fumigatus were used as test organisms. The sensitivity of detection in pure culture was 0.1 spore DNA equivalents per PCR reaction corresponding to 20 spores ml(-1) in the sample. However, 1 spore DNA equivalent per PCR reaction corresponding to 200 spores ml(-1) in the sample was the lowest amount of spores tested without interference in dust samples spiked with spores of either fungal species. The extent of inhibition was calculated using conventional and real-time PCR reactions containing fungal spores, specific primers, specific probes (for real-time PCR) and various amounts of dust. The results indicate that the extent of inhibition by dust on PCR varies with the type and amount of dust, and number of spores. No interference in the analysis of spiked samples was detected from 0.2 mg ml(-1) of four real-life dust samples at p-value >0.05 using 2 x 10(4) spores for conventional PCR and 2 x 10(5) spores for real-time PCR. However, samples containing >0.2 mg ml(-1) real-life dust compromised the PCR assay. These results suggest the potential usefulness of a simple sample processing method in conjunction with PCR for monitoring the fungal content of aerosols collected from indoor environments.     

Heavy metal concentrations in particle size fractions from street dust of Murcia (Spain) as the basis for risk assessment

Street dust has been sampled from six different types of land use of the city of Murcia (Spain). The samples were fractionated into eleven particle size fractions (<2, 2-10, 10-20, 20-50, 50-75, 75-106, 106-150, 150-180, 180-425, 425-850 μm and 850-2000 μm) and analyzed for Pb, Cu, Zn and Cd. The concentrations of these four potentially toxic metals were assessed, as well as the effect of particle size on their distribution. A severe enrichment of all metals was observed for all land-uses (industrial, suburban, urban and highways), with the concentration of all metals affected by the type of land-use. Coarse and fine particles in all cases showed concentrations of metals higher than those found in undisturbed areas. However, the results indicated a preferential partitioning of metals in fine particle size fractions in all cases, following a logarithmic distribution. The accumulation in the fine fractions was higher when the metals had an anthropogenic origin. The strong overrepresentation of metals in particles <10 μm indicates that if the finest fractions are removed by a vacuum-assisted dry sweeper or a regenerative-air sweeper the risk of metal dispersion and its consequent risk for humans will be highly reduced. Therefore, we recommend that risk assessment programs include monitoring of metal concentrations in dust where each land-use is separately evaluated. The finest particle fractions should be examined explicitly in order to apply the most efficient measures for reducing the risk of inhalation and ingestion of dust for humans and risk for the environment.     

Concentration, distribution and source apportionment of atmospheric polycyclic aromatic hydrocarbons in the southeast suburb of Beijing, China

Total suspended particle samples and gas phase samples were collected at three representative sampling sites in the southeastern suburb of Beijing from March 2005 to January 2006. The samples were analyzed for 16 US EPA priority PAHs using GC/MS. Concentrations of Sigma PAHs in particle and gas phases were 0.21-1.18 x 10(3) ng m(-3) and 9.5 x 10(2) ng-1.03 x 10(5) ng m(-3), respectively. PAH concentrations displayed seasonal variation in the order of winter>spring>autumn>summer for particle phase, and winter>autumn>summer>spring for gas phase. Partial correlation analysis indicates that PAH concentrations in particle phase are negatively correlated with temperature and positively correlated with air pollution index of SO(2). No significant correlation is observed between gas phase PAHs and the auxiliary parameters. Sources of PAH are identified through principal component analysis, and source contributions are estimated through multiple linear regression. Major sources of atmospheric PAHs in the study area include coal combustion, coke industry, vehicular emission and natural gas combustion.     

Differences in metal concentration by particle size in house dust and soil

The majority of particles that adhere to hands are <63 μm in diameter yet risk assessments for soil remediation are typically based on soil samples sieved to <250 μm. The objective of our study was to determine if there is a significant difference in metal concentration by particle size in both house dust and soil. We obtained indoor dust and yard soil samples from 10 houses in Tucson, Arizona. All samples were sieved to <63 μm and 63 to <150 μm and analyzed for 30 elements via ICP-MS following nitric acid digestion. We conducted t-tests of the log-transformed data to assess for significant differences that were adjusted with a Bonferroni correction to account for multiple comparisons. In house dust, significant differences in concentration were observed for Be, Al, and Mo between particles sizes, with a higher concentration observed in the smaller particle sizes. Significant differences were also determined for Mg, Ca, Cr, Co, Cu, Ge, Zr, Ag, Ba, and Pb concentration in yard soil samples, with the higher concentration observed in the smaller particles size for each element. The results of this exploratory study indicate that current risk assessment practices for soil remediation may under estimate non-dietary ingestion exposure. This is of particular concern for young children who are more vulnerable to this exposure route due to their high hand mouthing frequencies. Additional studies with a greater number of samples and wider geographic distribution with different climates and soil types should be completed to determine the most relevant sampling practices for risk assessment.     

重庆城区不同粒径颗粒物元素组分研究及来源识别

为研究重庆市大气颗粒物的污染特征及其来源,于2010年3—10月在主城区分别采集PM_1.0、PM_2.5和PM₁₀3种粒径的颗粒物样品,利用XRF分析其中的26种元素浓度。结果表明,重庆市主城区S元素在各粒径中含量都较高,细粒子中K的含量较高,粗粒子中Si、Ca和Fe的浓度较大。富集因子分析表明,主城区Cd、S、Se等污染元素的富集系数较大,且粒径越小,富集现象越明显。利用因子分析得出土壤风沙、扬尘、燃煤的燃烧、机动车燃油产生的尾气排放、生物质燃烧排放是重庆市颗粒物污染的主要来源。     

Diurnal trends in coarse particulate matter composition in the Los Angeles Basin

To investigate the diurnal profile of the concentration and composition of ambient coarse particles, three sampling sites were set up in the Los Angeles Basin to collect coarse particulate matter (CPM) in four different time periods of the day (morning, midday, afternoon and overnight) in summer and winter. The samples were analyzed for total and water-soluble elements, inorganic ions and water-soluble organic carbon (WSOC). In summer, highest concentrations of CPM gravimetric mass, mineral and road dust, and WSOC were observed in midday and afternoon, when the prevailing onshore wind was stronger. In general, atmospheric dilution was lower in winter, contributing to the accumulation of air pollutants during stagnation conditions. Turbulences induced by traffic become a significant particle re-suspension mechanism, particularly during winter night time, when mixing height was lowest. This is evident by the high levels of CPM mass, mineral and road dust in winter overnight at the near-freeway sites located in urban Los Angeles, and to a lesser extent in Riverside. WSOC levels were higher in summer, with a similar diurnal profile with mineral and road dust, indicating that they either share common sources, or that WSOC may be adsorbed or absorbed onto the surfaces of these dust particles. In general, the contribution of inorganic ions to CPM mass was greater in the overnight sampling period at all sampling sites, suggesting that the prevailing meteorological conditions (lower temperature and higher relative humidity) favor the formation of these ions in the coarse mode. Nitrate, the most abundant CPM-bound inorganic species in this basin, is found to be predominantly formed by reactions with sea salt particles in summer. When the sea salt concentrations were low, the reaction with mineral dust particles and the condensation of ammonium nitrate on CPM surfaces also contributes to the formation of nitrate in the coarse mode.     

中国北方干旱地区沙尘矿物特征研究

为了开展对我国沙暴传输规律的研究,了解我国北方干旱地区沙尘矿物特征有重要意义。本文对我国新疆塔克拉玛干沙漠区,内蒙腾格里沙漠区,贺兰山及银川等处的沙尘样品用X射线粉末衍射法进行矿物分析鉴定,并用原子吸收法作了特征元素的分析对比,根据矿物的X射线粉末衍射结果,结合元素分析,对沙漠源区及其以东地区沙尘矿物特征作了比较,判析了两个源区的矿物组成,讨论了它们的传输过程。     

江苏泰州城市霾天和沙尘天气溶胶中细菌群落结构特征研究

近年来,空气污染已成为长三角地区最关键的环境问题之一,气溶胶颗粒物(PM)是最主要的污染物之一.生物气溶胶作为颗粒物的重要组成部分,可能对空气质量和人体健康产生不利影响.利用高通量测序方法研究了江苏省泰州2019年11月至2020年1月期间发生沙尘和霾污染时生物气溶胶中细菌群落结构组成特征.结果表明:冬季沙尘天和霾天气...     

On-filter determination of collected wood dust by diffuse reflectance infrared Fourier-transform spectroscopy (DRIFTS)

A new analytical technique based on DRIFTS spectroscopy has been developed for the specific and sensitive determination of size-fractionated wood dust from 37 mm glass fiber filter samples collected with the Respicon sampler. A translational diffuse reflectance apparatus was modified to accept filter samples by incorporating a special filter holder in the sample stage and a clockwork motor to drive the translational stage during infrared scanning, thus providing an average analysis across the filter face. Filter samples were pre-treated with ethyl acetate to uniformly redeposit dust onto the filter and extract potential chemical interferences. Two absorbance maxima (1251 and 1291 cm(-1)), corresponding to the cellulose content of the wood, were suitable for quantitation of wood dust. Analysis of seven species of wood at 1291 cm(-1) showed an equivalent quantitative response for all species except maple. The response at 1251 cm(-1) was more variable across species but more sensitive for the softwoods. There was a statistically significant effect of particle size on the analytical response, so that analytical standards should be matched to the samples in terms of particle size distribution. Analytical limit of detection was approximately 0.08 mg of wood dust per sample with overall precision of about 6%. Comparison of DRIFTS and gravimetric analyses of 51 pure wood dust samples ranging from about 0.2 to 2 mg yielded a slope of 1.08 and r2 equal to 0.9. Other particulate contaminants common in the industrial wood processing industry showed little or no interference with the determination of wood dust by this method.     

Concentrations of heavy metals in urban soils of Talcahuano (Chile): a preliminary study

Concentrations of Cd, Cr, Ni, Pb, and Zn in the top-(0–10 cm) and sub-surface (10–20 cm) soils of the Talcahuano urban area were measured. The main soil properties (organic matter, CaCO₃, pH, particle sizes) were determined for a network of representative sampling sites. The mean Cr, Ni, Pb, and Zn contents in the urban topsoil samples from Talcahuano (37.8, 22.6, 35.2, 333 mg kg⁻¹, respectively) were compared with mean concentrations for other cities around the world. The results revealed higher concentrations of heavy metals in topsoil samples than in sub-surface samples. The samples from IS1, IS2, and IS3, located in the Talcahuano industrial park, had higher Cr, Ni, Pb, and Zn contents than did samples from the other sites. This was probably due to local pollution by industrial (metallurgical) dust, although other diffuse pollution throughout the entire port region (shipyards, metallurgy, the dismantling of old ships), and contributions from the wind from adjacent industrial, storage, and vessel areas clearly played a role. Heavy metals were lowest in the sample taken on school grounds (SG).     

大气可吸入颗粒物(PM10)中矿物组分的X射线衍射研究

利用X射线衍射技术对北京2002春季和夏季的可吸入颗粒物进行了研究.结果表明,北京春季和夏季可吸入颗粒物的矿物组成明显不同,春季可吸入颗粒物中的矿物以硅铝酸盐为主,同时存在碳酸盐、硫酸盐、硫化物、铁的氧化物、粘土矿物以及难以鉴定的矿物;在夏季的样品中,矿物的种类有所减少,却有新的物种出现,如氯化氨、硫酸氨等.XRD定量分析显示,在沙尘天气时,可吸入颗粒物中石英和粘土矿物以及非晶质分别占到24.1%、28.5%和2 0%,斜长石和方解石分别占到10.4%和8.1%,其他矿物总共不到10%.矿物组分的确定对可吸入颗粒物来源的识别有一定的指导作用.     

广州市春季一次沙尘天气过程综合观测

2017年4月21—23日广州市经历了一次远距离传输的沙尘天气过程,为了解沙尘过程对广州市空气质量的影响,基于广州市大气超级站,利用单颗粒气溶胶质谱(SPAMS)、气溶胶激光雷达观测数据并结合HYSPLIT后向轨迹模型分析了沙尘过程细颗粒物组分及污染来源贡献变化和沙尘气溶胶的来源及路径。结果表明:受沙尘过境影响,PM_(10)浓度大幅升高,PM_(2.5)/PM_(10)最小值仅为12.1%;沙尘过境期间影响近地面颗粒物的沙尘高度主要分布在1 km以下区域,近地面颗粒物消光系数均值为100.11 Mm~(-1),探测到最大退偏振比为0.28。SPAMS研究发现沙尘过境期间含硅酸盐颗粒物(SI)的细颗粒物数浓度比例达25.9%,是沙尘过境前的1.4倍;PM_(2.5)中扬尘贡献率明显增大,达到了17.3%,是沙尘过境前的1.9倍。后向轨迹模型HYSPLIT显示此次沙尘为典型的北方沙尘传输,沙尘源自中国西北地区,传输方向为自西北输送至华东地区后,转为东南方向影响广州市。     

The Effect of Traction Sanding on Urban Suspended Particles in Finland

Springtime urban road dust forms one of the most serious problems regarding air pollution in Finland. The composition and origin of springtime dust was studied in southern Finland with two different methods. Suspended particles (PM10 and TSP) were collected with high volume particle samplers and particle deposition was collected with moss bags. The composition of the PM(1.5-10) fraction was studied using individual particle analysis with SEM/EDX. The deposition in the moss bags was analysed with ICP-MS. The results showed that during the study period, approximately 10% of both PM(1.5-10) particles and the deposition originated from sanding. Other sources in the springtime PM(1.5-10) were e.g. asphalt aggregate or soil and combustion processes. It can be concluded that sanding produced a relatively small amount of particulate matter under the investigated circumstances.     

Classification of particles from the farm environment by automated sizing, counting and chemical characterisation with scanning electron microscopy-energy dispersive spectroscopy

About 60,000 particles in 288 aerosol samples collected during farm work have been characterised with automated particle analysis using scanning electron microscopy (SEM) and energy dispersive X-ray spectrometry (EDS). Based on EDS-analysis of materials with known composition (potato flour, alpha-quartz, K-feldspar and beta-wollastonite), criteria were developed for classification of particles as: (1) organic, (2) silicon-rich (silica), and (3) other inorganic particles. The reproducibility of the relative mass proportions in dust samples collected during farm work was 0.078 when approximately 200 particles were characterised per sample. Field samples from the farm environment showed clear differences in composition. Generally, inorganic particles dominated the particle mass. The proportion of the organic particle mass was highest for tending of swine and poultry, 55 and 38% respectively. Silica particles amounted to 10 to 20% of the total mass during handling crops, e.g. grain, straw, hay, potatoes, and onions. It seems likely that the results can be used in etiologic studies, but further validation would be needed for quantitative purposes.     

Real-time PCR detection of toxigenic Fusarium in airborne and settled grain dust and associations with trichothecene mycotoxins

Inhalation of immunomodulating mycotoxins produced by Fusarium spp. that are commonly found in grain dust may imply health risks for grain farmers. Airborne Fusarium and mycotoxin exposure levels are mainly unknown due to difficulties in identifying Fusarium and mycotoxins in personal aerosol samples. We used a novel real-time PCR method to quantify the fungal trichodiene synthase gene (tri5) and DNA specific to F. langsethiae and F. avenaceum in airborne and settled grain dust, determined the personal inhalant exposure level to toxigenic Fusarium during various activities, and evaluated whether quantitative measurements of Fusarium-DNA could predict trichothecene levels in grain dust. Airborne Fusarium-DNA was detected in personal samples even from short tasks (10-60 min). The median Fusarium-DNA level was significantly higher in settled than in airborne grain dust (p < 0.001), and only the F. langsethiae-DNA levels correlated significantly in settled and airborne dust (r(s) = 0.20, p = 0.003). Both F. langsethiae-DNA and tri5-DNA were associated with HT-2 and T-2 toxins (r(s) = 0.24-0.71, p < 0.05 to p < 00.01) in settled dust, and could thus be suitable as indicators for HT-2 and T-2. The median personal inhalant exposure to specific toxigenic Fusarium spp. was less than 1 genome m(-3), but the exposure ranged from 0-10(5) genomes m(-3). This study is the first to apply real-time PCR on personal samples of inhalable grain dust for the quantification of tri5 and species-specific Fusarium-DNA, which may have potential for risk assessments of inhaled trichothecenes.     

北京市大气PM10源解析研究

于2004年在北京市定陵、车公庄、古城、亦庄、房山和奥体中心6个采样点采集大气PM10环境样品,针对北京市颗粒物主要排放源采集土壤尘、建筑水泥尘、燃煤等污染源PM10样品,分别对其中的无机元素、离子、有机碳(OC)和元素碳(EC)进行测定。采用代表北京市颗粒物主要排放源PM10组分特征的成分谱,利用CMB受体模型对PM10来源进行解析。结果表明,PM10的最大来源为土壤尘,其它贡献源类依次为燃煤排放、机动车/燃油排放、二次粒子(SO42-、NO3-和NH4 )、建筑水泥尘。污染源贡献具有明显的季节变化,并存在一定的地域变化。