AhR agonist and genotoxicant bioavailability in a PAH-contaminated soil undergoing biological treatment

Background, aim, and scope  Degradation of the 16 US EPA priority PAHs in soil subjected to bioremediation is often achieved. However, the PAH loss is not always followed by a reduction in soil toxicity. For instance, bioanalytical testing of such soil using the chemical-activated luciferase gene expression (CALUX) assay, measuring the combined effect of all Ah receptor (AhR) activating compounds, occasionally indicates that the loss of PAHs does not correlate with the loss of Ah receptor-active compounds in the soil. In addition, standard PAH analysis does not address the issue of total toxicant bioavailability in bioremediated soil. Materials and methods  To address these questions, we have used the CALUX AhR agonist bioassay and the Comet genotoxicity bioassay with RTL-W1 cells to evaluate the toxic potential of different extracts from a PAH-contaminated soil undergoing large-scale bioremediation. The extracts were also chemically analyzed for PAH16 and PCDD/PCDF. Soil sampled on five occasions between day 0 and day 274 of biological treatment was shaken with n-butanol with vortex mixing at room temperature to determine the bioavailable fraction of contaminants. To establish total concentrations, parts of the same samples were extracted using an accelerated solvent extractor (ASE) with toluene at 100°C. The extracts were tested as inducers of AhR-dependent luciferase activity in the CALUX assay and for DNA breakage potential in the Comet bioassay. Results  The chemical analysis of the toluene extracts indicated slow degradation rates and the CALUX assay indicated high levels of AhR agonists in the same extracts. Compared to day 0, the bioavailable fractions showed no decrease in AhR agonist activity during the treatment but rather an up-going trend, which was supported by increasing levels of PAHs and an increased effect in the Comet bioassay after 274 days. The bio-TEQs calculated using the CALUX assay were higher than the TEQs calculated from chemical analysis in both extracts, indicating that there are additional toxic PAHs in both extracts that are not included in the chemically derived TEQ. Discussion  The response in the CALUX and the Comet bioassays as well as the chemical analysis indicate that the soil might be more toxic to organisms living in soil after 274 days of treatment than in the untreated soil, due to the release of previously sorbed PAHs and possibly also metabolic formation of novel toxicants. Conclusions  Our results put focus on the issue of slow degradation rates and bioavailability of PAHs during large-scale bioremediation treatments. The release of sorbed PAHs at the investigated PAH-contaminated site seemed to be faster than the degradation rate, which demonstrates the importance of considering the bioavailable fraction of contaminants during a bioremediation process. Recommendations and perspectives  It has to be ensured that soft remediation methods like biodegradation or the natural remediation approach do not result in the mobilization of toxic compounds including more mobile degradation products. For PAH-contaminated sites this cannot be assured merely by monitoring the 16 target PAHs. The combined use of a battery of biotests for different types of PAH effects such as the CALUX and the Comet assay together with bioavailability extraction methods may be a useful screening tool of bioremediation processes of PAH-contaminated soil and contribute to a more accurate risk assessment. If the bioremediation causes a release of bound PAHs that are left undegraded in an easily extracted fraction, the soil may be more toxic to organisms living in the soil as a result of the treatment. A prolonged treatment time may be one way to reduce the risk of remaining mobile PAHs. In critical cases, the remediation concept might have to be changed to ex situ remediation methods.     

Predicting bioremediation of hydrocarbons: Laboratory to field scale

There are strong drivers to increasingly adopt bioremediation as an effective technique for risk reduction of hydrocarbon impacted soils. Researchers often rely solely on chemical data to assess bioremediation efficiently, without making use of the numerous biological techniques for assessing microbial performance. Where used, laboratory experiments must be effectively extrapolated to the field scale. The aim of this research was to test laboratory derived data and move to the field scale. In this research, the remediation of over thirty hydrocarbon sites was studied in the laboratory using a range of analytical techniques. At elevated concentrations, the rate of degradation was best described by respiration and the total hydrocarbon concentration in soil. The number of bacterial degraders and heterotrophs as well as quantification of the bioavailable fraction allowed an estimation of how bioremediation would progress. The response of microbial biosensors proved a useful predictor of bioremediation in the absence of other microbial data. Field-scale trials on average took three times as long to reach the same endpoint as the laboratory trial. It is essential that practitioners justify the nature and frequency of sampling when managing remediation projects and estimations can be made using laboratory derived data. The value of bioremediation will be realised when those that practice the technology can offer transparent lines of evidence to explain their decisions.     

The estimation of PAH bioavailability in contaminated sediments using hydroxypropyl-beta-cyclodextrin and Triton X-100 extraction techniques

A study was conducted to investigate whether cyclodextrins and surfactants can be used to predict polycyclic aromatic hydrocarbon (PAH) bioavailability in contaminated sediments. Two sediment samples were extracted with aqueous solutions of hydroxypropyl-beta-cyclodextrin (HPCD) and Triton X-100. PAH removal during extraction was compared with PAH removal during biodegradation and solid-phase extraction. The latter two methods were used as reference methods to establish which part of the PAHs could be biodegraded and to what extent biodegradation was governed by bioavailability limitations. It was demonstrated that HPCD extraction followed solid-phase extraction and removed primarily readily bioavailable PAHs, while Triton X-100 extracted both readily and poorly bioavailable PAHs. Moreover, HPCD did not affect the degradation of PAHs in biodegradation experiments, while Triton X-100 enhanced the degradation of low molecular weight PAHs. It was concluded that HPCD extraction may provide a good method for the prediction of PAH bioavailability. Triton X-100 extraction is unfit for the prediction of PAH bioavailability.     

Bioavailability of residual polycyclic aromatic hydrocarbons following enhanced natural attenuation of creosote-contaminated soil

The impact of residual PAHs (2250 ± 71 μg total PAHs g⁻¹) following enhanced natural attenuation (ENA) of creosote-contaminated soil (7767 ± 1286 μg total PAHs g⁻¹) was assessed using a variety of ecological assays. Microtox™ results for aqueous soil extracts indicated that there was no significant difference in EC₅₀ values for uncontaminated, pre- and post-remediated soil. However, in studies conducted with Eisenia fetida, PAH bioaccumulation was reduced by up to 6.5-fold as a result of ENA. Similarly, Beta vulgaris L. biomass yields were increased 2.1-fold following ENA of creosote-contaminated soil. While earthworm and plant assays indicated that PAH bioavailability was reduced following ENA, the residual PAH fraction still exerted toxicological impacts on both receptors. Results from this study highlight that residual PAHs following ENA (presumably non-bioavailable to bioremediation) may still be bioavailable to important receptor organisms such as earthworms and plants.     

Microbial in situ degradation of aromatic hydrocarbons in a contaminated aquifer monitored by carbon isotope fractionation

We present an approach for characterizing in situ microbial degradation using the 13C/12C isotope fractionation of contaminants as an indicator of biodegradation. The 13C/12C isotope fractionation of aromatic hydrocarbons was studied in anoxic laboratory soil percolation columns with toluene or o-xylene as the sole carbon and electron source, and sulfate as electron acceptor. After approximately 2 months' of incubation, the soil microbial community degraded 32 mg toluene l(-1) and 44 mg o-xylene l(-1) to less than 0.05 mg l(-1), generating a stable concentration gradient in the column. The 13C/12C isotope ratio in the residual non-degraded fraction of toluene and o-xylene increased significantly, corresponding to isotope fractionation factors (alphaC) of 1.0015 and 1.0011, respectively. When the extent of biodegradation in the soil column was calculated based on the measured isotope ratios (R(t)) and an isotope fractionation factor (alphaC=1.0017) obtained from a sulfate-reducing batch culture the theoretical residual substrate concentrations (C(t)) matched the measured toluene concentrations in the column. This indicated that a calculation of biodegradation based on isotope fractionation could work in systems like soil columns. In a field study, a polluted, anoxic aquifer was analyzed for BTEX and PAH contaminants. These compounds were found to exhibit a significant concentration gradient along an 800-m groundwater flow path downstream of the source of contamination. A distinct increase in the carbon isotope ratio (delta13C) was observed for the residual non-degraded toluene (7.2 per thousand ), o-xylene (8.1 per thousand ) and naphthalene fractions (1.2 per thousand ). Based on the isotope values and the laboratory-derived isotope fractionation factors for toluene and o-xylene, the extent to which the residual substrate fraction in the monitoring wells had been degraded by microorganisms was calculated. The results revealed significant biodegradation along the groundwater flow path. In the wells at the end of the plume, the bioavailable toluene and o-xylene fractions had been almost completely reduced by in situ microbial degradation. Although indane and indene showed decreasing concentrations downstream of the groundwater flow path, suggesting microbial degradation, their carbon isotope ratios remained constant. As the physical properties of these compounds are similar to those of BTEX compounds, the constant isotope values of indane and indene indicated that microbial degradation did not lead to isotope fractionation of all aromatic hydrocarbons. In addition, physical interaction with the aquifer material during the groundwater passage did not significantly alter the carbon isotope composition of aromatic hydrocarbons.     

Prediction of complete bioremediation periods for PAH soil pollutants in different physical states by mechanistic models

Mass-transfer models and biodegradation models were developed for three theoretical physical states of polycyclic aromatic hydrocarbons (PAHs) in soil. These mechanistic models were used to calculate the treatment periods necessary for complete removal of the PAH pollutants from the soil under batch conditions. Results indicate that the bioremediation of PAHs in such systems is mainly mass-transfer limited. The potential for bioremediation as a treatment technique for PAH contaminated soils is therefore mainly determined by the mass-transfer dynamics of PAHs. Under mass-transfer limited conditions simplified mathematical models, based on the assumption of a zero dissolved PAH concentrations, can be used to predict the period of time needed for complete bioremediation.     

Electrokinetic enhancement of phenanthrene biodegradation in creosote-polluted clay soil

Given the difficulties caused by low-permeable soils in bioremediation, a new electrokinetic technology is proposed, based on laboratory results with phenanthrene, to afford bioremediation of polycyclic aromatic hydrocarbons (PAH) in clay soils. Microbial activity in a clay soil historically polluted with creosote was promoted using a specially designed electrokinetic cell with a permanent anode-to-cathode flow and controlled pH. The rates of phenanthrene losses during treatment were tenfold higher in soil treated with an electric field than in the control cells without current or microbial activity. Results from experiments with Tenax-assisted desorption and mineralization of 14C-labeled phenanthrene indicated that phenanthrene biodegradation was limited by mass-transfer of the chemical. We suggest that the enhancement effect of the applied electric field on phenanthrene biodegradation resulted from mobilization of the PAH and nutrients dissolved in the soil fluids.     

Factors inhibiting bioremediation of soil contaminated with weathered oils and drill cuttings

Oily drill cuttings and a soil contaminated with weathered crude oils were treated by enhanced biodegradation under tropical conditions in industrial scaled experiments. Oil contaminants were characterized by gas chromatography and mass spectrometry. This allowed for the identification of a mixture of two crude oils in the contaminated soil. After 12 months of bioremediation process, the removal of hydrocarbons reached by biodegradation an extent of 60% although nutrient amendment with elevated concentration of N-urea had highly detrimental effects on the hydrocarbon degrading fungal populations due to the production of toxic concentration of ammonia gas by nitrification. The saturated hydrocarbons were extensively assimilated, though n-alkanes were not completely removed. Aromatic hydrocarbons were less degraded than saturated whereas resin and asphaltene fractions were, surprisingly, partly assimilated. In laboratory conditions, the residual hydrocarbons in the field-treated materials were 15-20% further degraded when metabolic byproducts resulting from biodegradation were diluted or removed.     

Effects of nutrient and temperature on degradation of petroleum hydrocarbons in contaminated sub-Antarctic soil

Mesocosm studies using sub-Antarctic soil artificially contaminated with diesel or crude oil were conducted in Kerguelen Archipelago (49 degrees 21' S, 70 degrees 13' E) in an attempt to evaluate the potential of a bioremediation approach in high latitude environments. All mesocosms were sampled on a regular basis over six months period. Soils responded positively to temperature increase from 4 degrees C to 20 degrees C, and to the addition of a commercial oleophilic fertilizer containing N and P. Both factors increased the hydrocarbon-degrading microbial abundance and total petroleum hydrocarbons (TPH) degradation. In general, alkanes were faster degraded than polyaromatic hydrocarbons (PAHs). After 180 days, total alkane losses of both oils reached 77-95% whereas total PAHs never exceeded 80% with optimal conditions at 10 degrees C and fertilizer added. Detailed analysis of naphthalenes, dibenzothiophenes, phenanthrenes, and pyrenes showed a clear decrease of their degradation rate as a function of the size of the PAH molecules. During the experiment there was only a slight decrease in the toxicity, whereas the concentration of TPH decreased significantly during the same time. The most significant reduction in toxicity occurred at 4 degrees C. Therefore, bioremediation of hydrocarbon-contaminated sub-Antarctic soil appears to be feasible, and various engineering strategies, such as heating or amending the soil can accelerate hydrocarbon degradation. However, the residual toxicity of contaminated soil remained drastically high before the desired cleanup is complete and it can represent a limiting factor in the bioremediation of sub-Antarctic soil.     

Ecorisk evaluation and treatability potential of soils contaminated with petroleum hydrocarbon-based fuels

We used a series of toxicity tests to monitor oil degradation in the Kuwaiti oil lakes. Three soils from different locations with a history of hydrocarbon contamination were treated in bench-scale microcosms with controlled nutrient amendments, moisture content, and temperature that had promoted mineralization of total hydrocarbon and oil and grease in a preliminary study. Two hundred days of bioremediation treatment lowered hydrocarbon concentration to below 2 and 5 mg g(-1) for soils A and B, respectively, while in soil C hydrocarbon concentration remained at 12 mg g(-1). Although 85% of the total petroleum hydrocarbons (TPHs) in soil A were reduced 50d after treatment, results of the seed germination and Microtox tests suggested an initial increase in toxicity, indicating that toxic intermediary metabolites may have formed during biodegradation. Also, the significant decrease of TPHs and corresponding high toxicity levels were noted in soil B 200d after bioremediation. Clearly, toxicity values, and not just hydrocarbon concentration, are a key factor in assessing the effectiveness of bioremediation techniques. Field chemistry data showed a significant reduction in hydrocarbon levels after the biological treatment. We concluded that the toxicity assessment of the contaminated soil with a battery of toxicity bioassays could provide meaningful information regarding a characterization procedure in ecological risk assessment.     

Solid-phase bioassays and soil microbial activities to evaluate PAH-spiked soil ecotoxicity after a long-term bioremediation process simulating landfarming

The residual ecotoxicity of long-term bioremediated soils concomitantly spiked with three PAHs at four levels (15, 75, 150, 300 mg Sigma 3 PAHs kg(-1) soil) was evaluated using physico-chemical analyses, solid-phase bioassays and soil microbial activities. The pot-scale bioremediation process consisted of weekly moderate waterings in the presence or absence of sewage sludge compost (SSC) under greenhouse conditions. After 15 months, anthracene and pyrene were almost completely degraded whereas benzo[a]pyrene was still persisting, most apparently in SSC-amended soil treatments. However, no apparent toxic effects of the residual PAHs could be detected. SSC application at 40 t ha(-1) was performed to valorize the biowaste and stimulate PAH biodegradation but caused soil salinization and pH reduction at the end of the bioremediation process. Consequently, SSC-amended soils were characterized by strong phytotoxicity to lettuce and had adverse effects on the ostracod Heterocypris incongruens. Despite the smaller number of culturable bacterial populations in SSC-amended soils, soil enzymatic activities were not affected by the organic amendment and residual PAHs; and the bioremediation efficiency was likely to be more limited by the bioavailability of PAHs rather than by the total number of PAH-degraders.     

Assessment of five bioaccessibility assays for predicting the efficacy of petroleum hydrocarbon biodegradation in aged contaminated soils

In this study, the bioaccessibility of petroleum hydrocarbons in aged contaminated soils (1.6-67gkg(-1)) was assessed using four non-exhaustive extraction techniques (100% 1-butanol, 100% 1-propanol, 50% 1-propanol in water and hydroxypropyl-β-cyclodextrin) and the persulfate oxidation method. Using linear regression analysis, residual hydrocarbon concentrations following bioaccessibility assessment were compared to residual hydrocarbon concentrations following biodegradation in laboratory-scale microcosms in order to determine whether bioaccessibility assays can predict the endpoint of hydrocarbon biodegradation. The relationship between residual hydrocarbon concentrations following microcosm biodegradation and bioaccessibility assessment was linear (r(2)=0.71-0.97) indicating that bioaccessibility assays have the potential to predict the extent of hydrocarbon biodegradation. However, the slope of best fit varied depending on the hydrocarbon fractional range assessed. For the C(10)-C(14) hydrocarbon fraction, the slope of best fit ranged from 0.12 to 0.27 indicating that the non-exhaustive or persulfate oxidation methods removed 3.5-8 times more hydrocarbons than biodegradation. Conversely, for the higher molecular weight hydrocarbon fractions (C(29)-C(36) and C(37)-C(40)), biodegradation removed up to 3.3 times more hydrocarbons compared to bioaccessibility assays with the resulting slope of best fit ranging from 1.0-1.9 to 2.0-3.3 respectively. For mid-range hydrocarbons (C(15)-C(28)), a slope of approximately one was obtained indicating that C(15)-C(28) hydrocarbon removal by these bioaccessibility assays may approximate the extent of biodegradation. While this study demonstrates the potential of predicting biodegradation endpoints using bioaccessibility assays, limitations of the study include a small data set and that all soils were collected from a single site, presumably resulting from a single contamination source. Further evaluation and validation is required using soils from a range of hydrocarbon contamination sources in order to develop robust assays for predicting bioremediation endpoints in the field.     

Enhanced degradation of fluorene in soil slurry by Absidia cylindrospora and maltosyl-cyclodextrin

This study investigates the fungal biodegradation of fluorene, a polycyclic aromatic hydrocarbon, in liquid medium and soil slurry. Fungal strains and cyclodextrins were used in order to degrade fluorene and optimize fluorene bioavailability and degradation in soil slurries. After a procedure of selection in solid and liquid media, maltosyl-cyclodextrin, a branched cyclodextrin was chosen. 47 fungal strains isolated from a contaminated site were tested for biodegradation. Results showed the greater efficiency of "adapted" fungi isolated from contaminated soil vs reference strains belonging to the collection of the laboratory. These assays allowed us to select the most efficient strain, Absidia cylindrospora, which was used in a bioaugmentation process. Bioaugmentation tests were performed in an artificially contaminated non-sterile soil. In the presence of A. cylindrospora, more than 90% of the fluorene was degraded within 288 h, while 576 h were necessary in the absence of fungal bioremediation. It also appeared that biodegradation was enhanced by amendment with previously selected maltosyl-cyclodextrin. The results of this study indicate that A. cylindrospora and maltosyl-cyclodextrin could be used successfully in fluorene bioremediation systems.     

Monitoring of bioremediation by soil biological activities

An evaluation of soil biological activities as a monitoring instrument for the decontamination process of a mineral-oil-contaminated soil was made using measurements of microbial counts, soil respiration, soil biomass and several enzyme activities. The correlations between these parameters and with the levels of hydrocarbon residues were investigated; the effects of different N- and P-sources on hydrocarbon decontamination and soil biological activities were determined. Inorganic nutrients stimulated hydrocarbon biodegradation but not all biological activities to a significant extent. Biodegradation could be monitored well by soil biological parameters: the residual hydrocarbon content correlated positively with soil respiration, biomass-C (substrate-induced respiration), and with activities of soil dehydrogenase, urease and catalase. Soil lipase activity and the number of hydrocarbon utilizers correlated negatively (P < 0.0001) with the remaining hydrocarbon content.     

Assessment of contaminant lability during phytoremediation of polycyclic aromatic hydrocarbon impacted soil

Polycyclic aromatic hydrocarbons (PAHs) are recalcitrant compounds, some of which are known carcinogens, often found in high residual soil concentrations at industrial sites. Recent research has confirmed that phytoremediation holds promise as a low-cost treatment method for PAH contaminated soil. In this study, the lability of soil bound PAHs in the rhizosphere was estimated using solid phase extraction resin. An extraction time of 14 days was determined to be appropriate for this study. Resin-extractable PAHs, which are assumed to be more bioavailable, decreased during plant treatments. Significant reductions in the labile concentrations of several PAH compounds occurred over 12 months of plant growth. The differences in concentration between the unplanted and the planted soil indicate that the presence of plant roots, in addition to the passage of time, contributes to reduction in the bioavailability of target PAHs.     

The rhizosphere and PAH amendment mediate impacts on functional and structural bacterial diversity in sandy peat soil

To reveal the degradation capacity of bacteria in PAH polluted soil and rhizosphere we combined bacterial extradiol ring-cleavage dioxygenase and 16S rRNA analysis in Betula pubescens rhizoremediation. Characterisation of the functional bacterial community by RFLP revealed novel environmental dioxygenases, and their putative hosts were studied by 16S rRNA amplification. Plant rhizosphere and PAH amendment effects were detected by the RFLP/T-RFLP analysis. Functional species richness increased in the birch rhizosphere and PAH amendment impacted the compositional diversity of the dioxygenases and the structural 16S rRNA community. A shift from an Acidobacteria and Verrucomicrobia dominated to an Alpha- and Betaproteobacteria dominated community structure was detected in polluted soil. Clone sequence analysis indicated catabolic significance of Burkholderia in PAH polluted soil. These results advance our understanding of rhizoremediation and unveil the extent of uncharacterized functional bacteria to benefit bioremediation by facilitating the development of the molecular tool box to monitor bacterial populations in biodegradation.     

Bioremediation of coal tar PAH in soils using biodiesel

The addition of biodiesel together with nitrate and phosphate to soil containing coal tar, in laboratory and field experiments, resulted in degradation of coal tar polycyclic aromatic hydrocarbons (PAH) that was not apparent when the nutrients alone were added. The addition of motor diesel fuel instead of biodiesel was also tested. Over the 55 days of the field and laboratory experiments, the biodiesel resulted in an increased degradation of naphthalene in the coal tar by 52% and 85%, respectively, and motor diesel resulted in increased depletions of 85% and 96%, respectively. Other PAH containing up to four rings were depleted to lesser extents. The increases in PAH biodegradation by the diesel treatments were ascribed to tar solubilisation and dispersion thereby increasing the PAH bioavailability. The ready biodegradability and low phytotoxicity of biodiesel suggest that it may be suitable as a novel treatment for the bioremediation of coal tar contaminated soils.     

Investigation of potentially bioavailable and sequestrated forms of polycyclic aromatic hydrocarbons during sewage sludge composting

The present study focuses on the influence of the composting process on the formation of potentially bioavailable and sequestrated PAH fractions. The potentially bioavailable fraction was determined by means of a mild-solvent extraction (with n-butanol). The total and potentially bioavailable PAH content was evaluated in the consecutive composting stages, i.e. at the onset of the experiment, after the stabilization phase (on the 35th day), and after the maturation phase (on the 76th day). Four municipal sewage sludges with differentiated PAH content were selected for the present experiment. Eleven PAHs from the US EPA list (with exception of naphthalene, acenaphthylene, acenaphtene, fluorene and benz[ah]anthracene) were determined for the purpose of this experiment. The content of the total PAHs ranged from 3052 to 10352microg kg(-1). The share of the potentially bioavailable fraction was at a similar level in the sludge samples tested and ranged from 75% to 81%. Greater differences were noted in the share of the bioavailable fraction in the case of individual PAH groups. The influence of the composting process on the contribution of the potentially bioavailable fraction of the PAH clearly depended on the stage of the experiment and sewage sludge type. However, in the case of all sludges, a lowering of the bioavailable fraction by 19-52% as compared to the level at the outset of the experiment was observed. During the first phase (stabilization) of the sewage sludge composting process, a reduction of the PAH content took place mainly at the expense of potentially bioavailable fraction, whereas in the second phase (maturation), sequestration processes predominated. The above phenomenon was most clearly visible for the 6-rings PAHs.     

Dissipation of available benzo[a]pyrene in aging soil co-contaminated with cadmium and pyrene

A microcosm experiment was conducted to investigate the dissipation of available benzo[a]pyrene (BaP) in soils co-contaminated with cadmium (Cd) and pyrene (PYR) during aging process. The available residue of BaP in soil was separated into desorbing and non-desorbing fractions. The desorbing fraction contributed more to the dissipation of available BaP than the non-desorbing fraction did. The concentration of bound-residue fraction of BaP was quite low across all treatments. Within the duration of this study (250 days), transformation of BaP from available fractions to bound-residue fraction was not observed. Microbial degradation was the dominant mechanism of the dissipation of available BaP in the soil. The dissipation of available BaP was significantly inhibited with the increment in Cd level in the soil. The addition of PYR (250 mg kg^?1) remarkably promoted the dissipation of available BaP without reducing Cd availability in the soil. The calculated half-life of available BaP in the soil prolonged with the increment in Cd level; however, the addition of PYR shortened the half-life of available BaP by 13.1, 12.7, and 32.8 % in 0.44, 2.56, and 22 mg Cd kg^?1 soils, respectively. These results demonstrated that the inhibiting effect of Cd and the promoting effect of PYR on the dissipation of available BaP were competitive. Therefore, this study shows that the bioremediation process of BaP can be more complicated in co-contaminated soils.     

Anaerobic biodegradation of polycyclic aromatic hydrocarbon in soil

Known concentrations of phenanthrene, pyrene, anthracene, fluorene and acenapthene were added to soil samples to investigate the anaerobic degradation potential of polycyclic aromatic hydrocarbon (PAH). Consortia-treated river sediments taken from known sites of long-term pollution were added as inoculum. Mixtures of soil, consortia, and PAH (individually or combined) were amended with nutrients and batch incubated. High-to-low degradation rates for both soil types were phenanthrene > pyrene > anthracene > fluorene > acenaphthene. Degradation rates were faster in Taida soil than in Guishan soil. Faster individual PAH degradation rates were also observed in cultures containing a mixture of PAH substrates compared to the presence of a single substrate. Optimal incubation conditions were noted as pH 8.0 and 30 degrees C. Degradation was enhanced for PAH by the addition of acetate, lactate, or pyruvate. The addition of municipal sewage or oil refinery sludge to the soil samples stimulated PAH degradation. Biodegradation was also measured under three anaerobic conditions; results show the high-to-low order of biodegradation rates to be sulfate-reducing conditions > methanogenic conditions > nitrate-reducing conditions. The results show that sulfate-reducing bacteria, methanogen, and eubacteria are involved in the PAH degradation; sulfate-reducing bacteria constitute a major component of the PAH-adapted consortia.