Selective removal of Cr(VI) from aqueous solution by adsorption on mangosteen peel

Mangosteen peel, rich in polyphenolic compounds, was used to prepare the adsorbent exhibiting highly selective adsorption for Cr(VI) over other metal ions such as Pb²⁺, Fe³⁺, Zn²⁺, Cd²⁺, and Cr³⁺ at the pH values of 1～4. The chemical modification method proposed by using calcium hydroxide is quite cost-effective and ecofriendly without using any toxic reagents or causing any secondary pollution. The adsorption isotherm results revealed that the adsorption of Cr(VI) on the gel fit well the Langmuir adsorption model, and the maximum adsorption capacity for Cr(VI) at pH levels 1, 2, 3, and 4 was evaluated to be 2.46, 2.44, 1.99, and 2.14 mol/kg, respectively. The adsorption mechanism for Cr(VI) on the saponified gel was verified to follow an esterifiaction reaction coupled with the reduction of Cr(VI) to Cr(III) in which H⁺ plays a role of promoter. Thus, modified mangosteen peel gel has the prominent selectivity and low cost for Cr(VI) removal.     

Chromium (VI) remediation in aqueous solution by waste products (peel and seed) of mango (Mangifera indica L.) cultivars

The surface group characteristics of mango cultivar peels and seeds were evaluated by infrared spectra, PZC, and functional group composition. The adsorption/reduction of chromium (VI) in aqueous solutions was investigated by varying pH, contact time, initial Cr(VI) concentration, and adsorbent amount. The results show that both peel and seed powders of the mango cultivars showed significant adsorption/reduction capacity for Cr(VI) and that the desorption process obeys pseudo-second-order kinetics. Optimal adsorption occurred at pH 1.0, using a Cr(VI) concentration of 100 mg/L. On average, at pH 1.0, and a concentration of 3 g/L, the maximum adsorption/reduction capacity of Cr(VI) was 83% (peels 76%, seeds 90%). Of the mango powders tested, the most efficient were Tommy seed (100%) and Coite peel (98%) followed by Coite seed (96%) and Tommy peel powders (95%). The adsorption/reduction of Cr(VI) was complete (100%) by the mango seed, in comparison to the peel powders (97%) after 180 min. The data indicates that mango waste products, such as seed and peel powders, are both excellent candidates for the remediation of Cr(VI) from aqueous systems and due to the higher concentration of gallates and galloyl glucosides, the mango seed powders should be the powders of choice for future remediation projects.

     

Adsorptive removal of Pb2+ form aqueous solution by macrocyclic calix[4]naphthalene: kinetic, thermodynamic, and isotherm analysis

Background

The adsorption characteristics of Pb²⁺ ions from aqueous solutions onto calix[4]naphthalene have been investigated.

Method

Calix[4]naphthalene was prepared by the condensation of 1-naphthol and formaldehyde (1:2) in presence of hydrochloric acid at 80°C. The effect of various operation parameters, such as solution pH, initial metal ion concentration, contact time, and temperature, on the adsorption capacity of calix[4]naphthalene for Pb²⁺ have been investigated.

Result

Experimental results showed that the adsorption of Pb²⁺ ions increased with the increase in solution pH and temperature. Langmuir and Freundlich isotherms models were used to describe the adsorption behavior of Pb²⁺ by calix[4]naphthalene. Equilibrium data fitted well with the Langmuir isotherm model and the maximum adsorption capacity of calix[4]naphthalene for Pb²⁺ at 30°C was found to be 29.15 mg g^?1. Kinetic studies indicated that the adsorption followed pseudo-second order model and the thermodynamic studies revealed that the adsorption process was spontaneous and endothermic in nature. The obtained results demonstrated that calix[4]naphthalene can be used as an effective adsorbent for Pb²⁺ ions removal from water.     

Removal of heavy metal ions from wastewater by a novel HEA/AMPS copolymer hydrogel: preparation, characterization, and mechanism

This study aims to synthesize 2-hydroxyethyl acrylate (HEA) and 2-acrylamido-2-methylpropane sulfonic (AMPS) acid-based hydrogels by gamma radiation and to investigate their swelling behavior and heavy metal ion adsorption capabilities. The copolymer hydrogels prepared were characterized via scanning electron microscopy, Fourier transformed infrared spectra, thermal gravimetric analysis, and X-ray photoelectron spectroscopy. The research showed that the copolymer hydrogel was beneficial for permeation due to its porous structure. In addition, the experimental group A-2-d [70 % water volume ratio and (n (AMPS)/n (HEA))?=?1:1] was an optimal adsorbent. The optimal pH was 6.0 and the optimal temperature was 15 °C. Pb²⁺, Cd²⁺, Cu²⁺, and Fe³+ achieved adsorption equilibriums within 24 h, whereas Cr³⁺ reached equilibrium in 5 h. Pb²+, Cd²⁺, Cr³⁺, and Fe³⁺ maximum load capacity was 1,000 mg L^?1, whereas the Cu²⁺ maximum capacity was 500 mg L^?1. The priority order in the multicomponent adsorption was Cr³⁺>Fe³⁺>Cu²⁺>Cd²⁺>Pb²⁺. The adsorption process of the HEA/AMPS copolymer hydrogel for the heavy metal ions was mainly due to chemisorption, and was only partly due to physisorption, according to the pseudo-second-order equation and Langmuir adsorption isotherm analyses. The HEA/AMPS copolymer hydrogel was confirmed to be an effective adsorbent for heavy metal ion adsorption.     

Removal of Pb2+ from aqueous solution by adsorption on chemically modified muskmelon peel

A cost-effective biosorbent was prepared by a green chemical modification process from muskmelon peel by saponification with alkaline solution of Ca(OH)₂. Its adsorption behavior for lead ions was investigated and found to exhibit excellent adsorption properties. Results showed that the optimal equilibrium pH range for 100 % adsorption is from 4 up to 6.4. Adsorption equilibrium was attained within 10 min. The adsorption process can be described well by Langmuir model and pseudo-second-order kinetics equation, respectively. The maximum adsorption capacity for lead ions was found to be 0.81 mol/kg. Pectic acid contained in the muskmelon peel is the main factor responsible for the uptake of lead ions onto the gel, and the chemical modification process presented in this study can be assumed effective to prepare other similar biomaterials. The large adsorption capacity and the fast adsorption rate indicated that chemically saponified muskmelon peel gel in present study has great potential to be used as a cost-effective adsorbent for the removal of lead ions from the water.     

Biosorption of chromium (VI) from aqueous solutions and ANN modelling

The use of sustainable, green and biodegradable natural wastes for Cr(VI) detoxification from the contaminated wastewater is considered as a challenging issue. The present research is aimed to assess the effectiveness of seven different natural biomaterials, such as jackfruit leaf, mango leaf, onion peel, garlic peel, bamboo leaf, acid treated rubber leaf and coconut shell powder, for Cr(VI) eradication from aqueous solution by biosorption process. Characterizations were conducted using SEM, BET and FTIR spectroscopy. The effects of operating parameters, viz., pH, initial Cr(VI) ion concentration, adsorbent dosages, contact time and temperature on metal removal efficiency, were studied. The biosorption mechanism was described by the pseudo-second-order model and Langmuir isotherm model. The biosorption process was exothermic, spontaneous and chemical (except garlic peel) in nature. The sequence of adsorption capacity was mango leaf > jackfruit leaf > acid treated rubber leaf > onion peel > bamboo leaf > garlic peel > coconut shell with maximum Langmuir adsorption capacity of 35.7 mg g^?1 for mango leaf. The treated effluent can be reused. Desorption study suggested effective reuse of the adsorbents up to three cycles, and safe disposal method of the used adsorbents suggested biodegradability and sustainability of the process by reapplication of the spent adsorbent and ultimately leading towards zero wastages. The performances of the adsorbents were verified with wastewater from electroplating industry. The scale-up study reported for industrial applications. ANN modelling using multilayer perception with gradient descent (GD) and Levenberg-Marquart (LM) algorithm had been successfully used for prediction of Cr(VI) removal efficiency. The study explores the undiscovered potential of the natural waste materials for sustainable existence of small and medium sector industries, especially in the third world countries by protecting the environment by eco-innovation.     

巯基化改性膨润土对重金属的吸附性能

以钙基膨润土为基本材料,制备了巯基化改性膨润土,并对比研究了此材料与其他17种改性膨润土和原材料对重金属的吸附性能.结果表明,巯基化膨润土对镉的吸附能力显著优于其他材料,在本实验条件下,其对镉的吸附率高于其他材料30％以上,对镉的吸附量可达52.1 mg/g.巯基化膨润土对铅的吸附能力在重金属竞争吸附条件下优于其他材料,而其对镍的吸附能力在所有材料中处于中等水平;另外,巯基化膨润土对3种重金属的吸附受重金属竞争吸附影响较小.因此,在所研究的材料中,巯基化膨润土材料是一种最理想的重金属吸附材料.     

三乙二醇二甲基丙烯酸酯为交联剂制备的高吸水树脂对重金属的吸附

以前期工作中合成的树脂PAANa-TE为吸附剂进行重金属吸附测试,考察吸附剂用量、丙烯酸中和度、吸附时间、溶液pH、初始浓度和吸附温度对树脂吸附重金属离子Cu2+、Pb2+、Cr3+和Co2+性能的影响,用原子吸收分光光度计测定了树脂吸附Cu2+、Pb2+、Cr3+和Co2+后的残留浓度,树脂对4种金属离子的吸附容量分别为21.59、2.39、5.66和4.98 mmol/g,吸附容量大小为Cu2+Cr3+Co2+Pb2+,吸附速率顺序为Cr3+Pb2+Cu2+Co2+。结果表明,该树脂对高浓度重金属离子有较快速,高效率的吸附,吸附过程在100 min左右吸附容量达到最大,并用不同浓度的酸对吸附重金属离子的树脂进行脱附处理,脱附量很小,据此可考虑进一步对金属离子进行回收处理。且脱附率较低,因此,可对工业化和城市化进程所产生的各种化学形态的重金属水体污染物造成的生态环境和质量问题起到重要的改善作用。     

天然土壤对水溶液中Pb~(2+)的吸附

以天然土壤为吸附材料,处理水溶液中的Pb2+,研究3种土壤对水溶液中Pb2+的吸附过程并结合土壤的理化性质对吸附规律进行初步分析。结果表明,棕壤和钙层土对Pb2+的吸附能力远大于红壤,3种土壤对Pb2+的吸附动力学曲线与二次动力学方程有较好的拟合性;3种土壤吸附Pb2+的吸附等温线用Langmuir方程描述最为合适,其次是Temkin方程,再次是Frenudlich方程,钙层土对Pb2+的吸附受温度影响较为明显;由实验数据得出的反应热力学参数说明3种土壤对Pb2+的吸附是自发的吸热过程;Pb2+在饱和吸附的土壤表面覆盖率并不高;土壤对Pb2+的吸附能力受各种土壤理化性质的综合影响。     

硅烷化改性沸石对重金属离子的吸附性能

制得一种用于重金属废水处理的新型硅烷化改性沸石吸附剂,成本低、效果显著且稳定。通过对改性沸石表征,分析了改性对沸石结构的影响。结果表明,改性一定程度降低了原沸石的晶体特征,但基本上保持了其结构组成;硅烷化改性成功地在沸石上接枝了氨基。对硅烷化沸石的特性研究,得出硅烷化沸石对Ni2+、Cu2+、Zn2+和Pb2+吸附最佳投加量为1、1、1.6和0.6 g/L,且此时对4种离子的去除率也较好;吸附动力学研究得出,其吸附过程可用二级动力学方程较好地拟合;吸附达到平衡时,4种金属离子的平衡吸附量分别为11.23、17.41、15.45和59.42 mg/g;硅烷化沸石对金属离子的吸附行为更符合Langmuir模型,为化学吸附;在酸性条件下(pH=2～6),硅烷化沸石仍保持一定的吸附能力,具有一定的耐酸性。     

Removal and recovery of copper and nickel ions from aqueous solution by poly(methacrylamide-co-acrylic acid)/montmorillonite nanocomposites

Nanocomposite hydrogels based on poly(methacrylamide-co-acrylic acid) and nano-sized montmorillonite were prepared by aqueous dispersion and in situ radical polymerization. Optimum sorption conditions were determined as a function of montmorillonite content, contact time, pH, and temperature. The equilibrium data of Cu²⁺ and Ni²⁺ conformed to the Freundlich and Langmuir isotherms in terms of relatively high regression values. The maximum monolayer adsorption capacity of the nanocomposite hydrogel (with 3 wt% montmorillonite content), as obtained from the Langmuir adsorption isotherm, was found to be 49.26 and 46.94 mg g^?1 for Cu²⁺ and Ni²⁺, respectively, at contact time?=?60 min, pH?=?6.8, adsorbent dose?=?100 mg/ml, and temperature?=?318 K. Kinetic studies of single system indicated that the pseudo-second order is the best fit with a high correlation coefficient (R ²?=?0.97–0.99). The result of five times sequential adsorption–desorption cycle shows a good degree of desorption and a high adsorption efficiency.     

4种脂肪多胺修饰硅胶对铅离子的吸附

为了合成高效铅离子吸附剂,了解其对铅离子的吸附规律。采用(3-氯丙基)三甲氧基硅烷(CPTS)架桥法,以硅胶(SG)为载体,乙二胺(EDA)、二乙烯三胺(DETA)、三乙烯四胺(TETA)和四乙烯五胺(TEPA)为表面修饰剂,合成了4种胺化硅胶,测定了它们的红外光谱、热重等性质以及对Cu2+、Zn2+和Pb2+的吸附能力。结果表明,4种胺化硅胶对Pb2+的吸附量均大于Cu2+和Zn2+的吸附量,其中DETA修饰硅胶对Pb2+的吸附量较高。4种胺化硅胶对Pb2+的吸附过程较好地符合拟二级动力学模型以及Langmuir和Scatchart等温吸附热力学模型,其对Pb2+吸附的速率常数、饱和吸附量以及吸附位点数由大到小的顺序一致,均为SG-DETASG-TEPASG-EDASG-TETA。4种胺化硅胶对Pb2+的吸附速率和吸附量呈现"奇数胺"增强效应,亲和常数则依次减小。阐明了脂肪多胺修饰硅胶对Pb2+的吸附规律,并进一步讨论了Scatchart和Langmuir热力学模型的统一性。     

Multi-component adsorption of copper,nickel and zinc from aqueous solutions onto activated carbon prepared from date stones

The removal of Cu²⁺, Ni²⁺, and Zn²⁺ ions from their multi-component aqueous mixture by sorption on activated carbon prepared from date stones was investigated. In the batch tests, experimental parameters were studied, including solution pH, contact time, initial metal ions concentration, and temperature. Adsorption efficiency of the heavy metals was pH-dependent and the maximum adsorption was found to occur at around 5.5 for Cu, Zn, and Ni. The maximum sorption capacities calculated by applying the Langmuir isotherm were 18.68 mg/g for Cu, 16.12 mg/g for Ni, and 12.19 mg/g for Zn. The competitive adsorption studies showed that the adsorption affinity order of the three heavy metals was Cu²⁺?>?Ni²⁺?>?Zn²⁺. The test results using real wastewater indicated that the prepared activated carbon could be used as a cheap adsorbent for the removal of heavy metals in aqueous solutions.     

Copper (II) adsorption by the extracellular polymeric substance extracted from waste activated sludge after short-time aerobic digestion

The extracellular polymeric substance (EPS) extracted from waste activated sludge (WAS) after short-time aerobic digestion was investigated to be used as a novel biosorbent for Cu²⁺ removal from water. The EPS consisted of protein (52.6 %, w/w), polysaccharide (30.7 %, w/w), and nucleic acid (16.7 %, w/w). Short-time aerobic digestion process of WAS for about 4 h promoted the productivity growth of the EPS for about 10 %. With a molecular weight of about 1.9?×?10⁶ Da, the EPS showed a linear structure with long chains, and contained carboxyl, hydroxyl, and amino groups. The sorption kinetics was well fit for the pseudo-second-order model, and the maximum sorption capacity of the EPS (700.3 mg Cu²⁺/g EPS) was markedly greater than those of the reported biosorbents. Both Langmuir model and Freundlich model commendably described the sorption isotherm. The Gibbs free energy analysis of the adsorption showed that the sorption process was feasible and spontaneous. According to the complex results of multiple analytical techniques, including scanning electron microscopy, Fourier transform infrared spectroscopy, atomic force microscopy, etc., the adsorption process took place via both physical and chemical sorption, but the electrostatic interaction between sorption sites with the functional groups and Cu²⁺ is the major mechanism.     

Esterification of sugarcane bagasse by citric acid for Pb2+ adsorption: effect of different chemical pretreatment methods

In this study, different pretreatment strategies of sugarcane bagasse prior to citric acid modification were investigated in terms of Pb²⁺ adsorption capacity. Pretreatment strategies included the use of NaOH, HCl, and C₂H₅OH in various concentrations. In order to fundamentally understand how these pretreatment methods affect the modification of sugarcane bagasse by citric acid as well as the Pb²⁺ adsorption capacity of sugarcane bagasse, three main components of sugarcane bagasse namely cellulose, hemicellulose, and lignin were isolated and esterified by citric acid under the same conditions. ATR-FTIR, XPS, SEM, and an analysis of the number of carboxylic acid groups were used to investigate the physicochemical and chemical properties of the materials. These three components were proved to participate in adsorption and induce the esterification with citric acid. Hence, pretreatment with ethanol and 0.01 M NaOH which could retain cellulose, hemicellulose, and lignin in sugarcane bagasse achieved a high Pb²⁺ adsorption capacity, i.e., 122.4 and 97 mg/g after the esterification with citric acid. In contrast, pretreatment with 0.5 M NaOH and 0.1 M HCl removed lignin and hemicellulose, leading to the lowest value of approximately 45 mg/g for citric acid esterified-pretreated sugarcane bagasse. XPS analysis and number of carboxylic group measurement confirmed the esterification between bagasse and citric acid. To understand the adsorption mechanism of adsorbent, two kinetic models including pseudo-first-order model and pseudo-second-order model were applied. The experimental data were well described by the pseudo-second-order model. The adsorption isotherm data were fitted Langmuir and Freundlich.

     

炭化柚子皮对废水中双酚A的吸附

采用磷酸二氢钾活化原材料柚子皮，分别在300℃和600℃对活化后柚子皮进行炭化，制得吸附剂（CC300和CC600），通过静态吸附实验研究了炭化柚子皮对双酚A的吸附性能。采用比表面积分析仪对炭化柚子皮进行表征，实验考察了pH值、吸附时间和温度对双酚A吸附的影响，并详细研究了炭化柚子皮对双酚A的吸附行为和机理。结果表明，高温炭化柚子皮（CC600）吸附双酚A能力比低温炭化（CC300）的强，其吸附较好地满足Langmuir和Freundlich等温方程；动力学研究表明，其吸附速率快，在150min内能达到吸附平衡，准二级动力学模型较好地描述该吸附行为，相关系数高达0．99：计算了热力学参数△G、△H和△S的值,△G为负值,说明该吸附过程为自发过程。     

4A沸石分子筛处理中低浓度氨氮废水

利用天然沸石、采用水热合成法制备4A沸石分子筛,用XRD和SEM进行了表征。通过考察吸附剂用量、pH、共存金属阳离子、吸附时间、氨氮废水初始浓度、温度对吸附性能的影响,结合动力学方程、吸附等温线、热力学函数等研究了吸附性能和机理。结果表明,当4 g/L的4A沸石分子筛在废水pH值为4~8的条件下对中低浓度氨氮吸附120min后,去除率可达88%;废水中共存单一金属阳离子(Pb2+、Cu2+、Ca2+和Mg2+)浓度大于100 mg/L时,对中低浓度的NH+4有强烈的竞争吸附;氨氮的吸附过程较好地符合准二级动力学方程、Freundlich模型,是一种混乱度增加、自发的放热过程。     

Characterization and adsorption capacity of modified 3D porous aerogel from grapefruit peels for removal of oils and organic solvents

With the rapid industrialization, especially offshore oil exploitation, frequent leakage incidents of oils/organic solvents have adversely affected ecological systems and environmental resources. Therefore, great interest has been shown in developing new materials to eliminate these organic pollutants, which have become worldwide problems. In this study, a cost-effective, environmentally friendly porous aerogel with three-dimensional (3D) structure was prepared from grapefruit peel by a facile hydrothermal method as the adsorbent of oils/organic solvents. The as-prepared modified grapefruit peel aerogel (M-GPA) showed mesoporous structure with high specific surface area of 36.42 m²/g and large pore volume of 0.0371 cm³/g. The excellent hydrophobicity of M-GPA with a water contact angle of 141.2° indicated a strong potential for adsorption of oils and organic solvents. The high adsorption capacity of M-GPA for a series of oils and organic solvents was 8 to 52 times as much as its own weight. Moreover, the M-GPA was easily regenerated and a high adsorption capacity recovery above 97% was maintained after five adsorption–regeneration cycles. Therefore, the M-GPA is a promising recyclable adsorbent for the removal of oils/organic solvents from polluted water.

     

液/固体系中硅藻土对Pb2+和Cd2+的吸附机制

为了提高硅藻土在重金属废水处理上的应用水平,采用静态吸附实验考察了液/固体系中硅藻土对Pb2＋、Cd2＋的吸附影响因素、吸附等温线和吸附动力学属性。结果表明,随着投加量的减少,离子初始浓度的提高,pH值的增大,吸附作用时间的延长,硅藻土对Pb2＋、Cd2＋吸附量不断上升;硅藻土对Pb2＋、Cd2＋的等温吸附都符合Langmuir模型,硅藻土对Pb2＋、Cd2＋最大吸附量分别为10.428 mg/g和7.916 mg/g,硅藻土对Pb2＋具有更好的吸附能力;Pb2＋具有较低的水合自由能,更容易脱去水膜与硅藻土孔道内的活性基团发生吸附作用;双常数扩散方程可以很好地描述硅藻土对Pb2＋、Cd2＋的吸附动力学属性,硅藻土对Cd2＋有较快的吸附速率。     

Use of carbonised beet pulp carbon for removal of Remazol Turquoise Blue-G 133 from aqueous solution

Carbonised beet pulp (BPC) produced from agricultural solid waste by-product in sugar industry was used as adsorbent for the removal of Remazol Turquoise Blue-G 133 (RTB-G 133) dye in this study. The kinetics and equilibrium of sorption process were investigated with respect to pH, temperature and initial dye concentration. Adsorption studies with real textile wastewater were also performed. The results showed that adsorption was a strongly pH-dependent process, and optimum pH was determined as 1.0. The maximum dye adsorption capacity was obtained as 47.0 mg g^?1at the temperature of 25 °C at this pH value. The Freundlich and Langmuir adsorption models were used for describing the adsorption equilibrium data of the dye, and isotherm constants were evaluated depending on sorption temperature. Equilibrium data of RTB-G 133 sorption fitted very well to the Freundlich isotherm. Mass transfer and kinetic models were applied to the experimental data to examine the mechanisms of adsorption and potential rate-controlling steps. It was found that both external mass transfer and intra-particle diffusion played an important role in the adsorption mechanisms of dye and adsorption kinetics followed the pseudo second-order type kinetic model. The thermodynamic analysis indicated that the sorption process was exothermic and spontaneous in nature.