北京灰霾天气PM10中微量元素的分布特征

采用电感耦合等离子体质谱法(ICP-MS)对北京市2008年4月和5月不同采样点采集的灰霾天PM₁₀样品中的15种微量元素进行了分析,得出了Ti、Fe、Zn、Sn、Pb为全样样品中相对含量较高元素;Ti、Mn、Ni、Cu、Zn、Pb是水溶样样品中相对含量较高元素。与晴天相比,灰霾天样品中微量元素可溶性增强,对人体危害更严重。与2002年分析数据进行对比,因2002年缺少Cr、Cd元素的测试值,全样样品中除了Co、Ni、Cu、Mo元素外,其余测试元素的浓度均有不同程度的升高,Fe和Sn元素的增幅最大。水溶样品中,参与对比元素的含量均下降。文中对含量相对较高的Cr、Mn、Fe、Cu、Zn、Cd、Sn和Pb元素进行了源解析,分析得出采样点附近的交通源及地面扬尘是这些元素的主要来源。     

Solid phase extraction of Cu(II), Ni(II), Pb(II), Cd(II) and Mn(II) ions with 1-(2-thiazolylazo)-2-naphthol loaded Amberlite XAD-1180

A new method for separation and preconcentration of trace amounts of Cu(II), Ni(II), Pb(II), Cd(II) and Mn(II) ions in various matrices was proposed. The method is based on the adsorption and chelation of the metal ions on a column containing Amberlite XAD-1180 resin impregnated with 1-(2-thiazolylazo)-2-naphthol (TAN) reagent prior to their determination by flame atomic absorption spectrometry (FAAS). The effect of pH, type, concentration and volume of eluent, sample volume, flow rates of sample and elution solutions, and interfering ions have been investigated. The optimum pH for simultaneous retention of all the metal ions was 9. Eluent for quantitative elution was 20 ml of 2 mol l(-1) HNO(3). The optimum sample and eluent flow rates were found as 4 ml min(-1), and also sample volume was 500 ml, except for Mn (87% recovery). The sorption capacity of the resin was found to be 0.77, 0.41, 0.57, and 0.30 mg g(-1) for Cu(II), Ni(II), Cd(II), and Mn(II), respectively. The preconcentration factor of the method was 200 for Cu(II), 150 for Pb(II), 100 for Cd(II) and Ni(II), and 50 for Mn(II). The recovery values for all of the metal ions were > or = 95% and relative standard deviations (RSDs) were < or = 5.1%. The detection limit values were in the range of 0.03 and 1.19 microg l(-1). The accuracy of the method was confirmed by analysing the certified reference materials (TMDA 54.4 fortified lake water and GBW 07605 tea samples) and the recovery studies. This procedure was applied to the determination of Cu(II), Ni(II), Pb(II), Cd(II) and Mn(II) in waste water and lake water samples.     

Solid phase extraction of Cd,Pb, Ni,Cu, and Zn in environmental samples on multiwalled carbon nanotubes

A simple and sensitive solid phase extraction (SPE) method on multiwalled carbon nanotubes (MWCNTs) is presented for the determination of cadmium, lead, nickel, copper, and zinc at trace levels combined with flame atomic absorption spectrometry. The effects of parameters like pH, sample volume, sample and eluent flow rates, eluent concentration, and volume and type of eluent on the recovery of trace elements was examined. The metals retained on the nanotube at pH 6.5 as α-benzoin oxime complexes were eluted by 10 mL 2 M HNO₃ in acetone. The influence of matrix ions on the developed method was also evaluated. The preconcentration factor of the method was found to be 50. The detection limits for Cd(II), Pb(II), Ni(II), Cu(II), and Zn(II) were found as 1.7, 5.5, 6.0, 2.3, and 2.4 μg L^?1, respectively. To test the accuracy of the method, the method was applied to TMDA-70 fortified lake water and Spinach 1570A standard reference materials. Addition recovery studies were applied to tap water and cracked wheat samples, and determination of the analyte elements was carried out in some food samples with good results.     

Major and trace element contents in apples from a cultivated area of central Greece

Forty-two soil and apple samples from central Greece were collected and analyzed with regards to the content in major (Ca, Fe, K, Mg, Na, P, and S) and trace elements (As, B, Ba, Cd, Co, Cr, Cu, Hg, Mn, Mo, Ni, Pb, Sb, Sc, Se, Sr, Ti, and Zn). Soil samples were analyzed by inductively coupled plasma atomic emission spectrometry, while for the apples inductively coupled plasma mass spectrometry was implemented. Several elements such as As, B, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Se, Ti, and Zn, represent high concentrations in apples from the study area. These relatively high concentrations may be a consequence of the local geology, along with the excessive application of agricultural products such as fertilizers and agrochemicals.     

Heavy Metal Levels in Biota and Sediments in the Northern Coast of the Marmara Sea

Concentration of Cd, Co, Cr, Ni, Zn, Fe, Mn, Pb and Cu were determinedin biota and sediment samples collected from the Marmara Sea in Turkey. The levels of Zn, Fe, Mn, Pb and Cu in the macroalgae are higher than previous studies in the Marmara Sea. Moreover, Cu and Zn concentrations at the present study are significantly high than Bosphorus and Black Sea algae. The order heavy metal concentrations in the mussel samples was: Fe > Zn > Ni > Mn > Cu > Pb > Cr > Cd > Co. The metal concentrations are generally lower when compared with the Black Sea mussels except Pb. At the same time, concentrations of Pb, Cu and Zn in the mussel species are lower when compared with the results in the Aegean Sea. The ranges of Mn and Cu in the tested fish samples are higher than Black Sea fish. On the other hand, Cd, Co, Cr, Zn and Pb concentrations are lower. The northern coast of the Marmara Sea having the highest metal concentrations in sediments as follows: Co, Cr, Ni, Fe at ?arköy ; Pb, Cu at M. Ere?li; Cd, Zn, Mn at Menek?e. The heavy metal levels in the sediment samples are lower than other areas in the Marmara Sea.     

Heavy metals in Yeniçağa Lake and its potential sources: soil,water, sediment,and plankton

The distribution and accumulation of heavy metals (Al, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Mo, Cd, Sn, Ba, Pb) in the water, sediments, plankton of Yeniça?a Lake, and its potential sources (creeks, sewage, artesian well, soil) were investigated during 1-year study period as monthly or seasonally. Element analyses were performed by ICP–MS. Results showed that the trace and toxic elements (Al, As, Mn, Pb, Fe) concentration in lake water and/or its feeding sources were above the recommended water standards (WHO, EC, EPA, TS-266). It was found that the maximum accumulation of the heavy metals iron, aluminum, manganese, zinc, and barium in the sediment of Yeniça?a Lake. The accumulation order of trace metals were Fe > Al > Mn > Zn > Ba > Ni > Cr > As > Cu > Pb > Co > Mo > Sn > Cd in the lake, creeks sediment, and soil samples. The similar results suggest that the accumulation of heavy metals in the sediment is a natural process. Metals accumulated in the lake are naturally mixed from the soil. However, the presence of heavy metals in the analysis of artesian well water and sewage reveals that the transportation occurs also from the groundwater to the lake. The results obtained in plankton in Yeniça?a Lake showed that aluminum, iron, manganese, zinc, and barium were most accumulated elements in the plankton. The lower averages of lead prevalent in the water and sediment during some months were seen to have a significant mean accumulation in the plankton.     

Heavy Metal Pollution of Surface Soil in the Thrace Region, Turkey

Abstact Samples of surface soil were collected at 73 sites in the Thrace region, northwest part of Turkey. Two complementary analytical techniques, epithermal neutron activation analysis (ENAA) and atomic absorption spectrometry (AAS) with flame and graphite furnace atomization were used to determine 35 elements in the soil samples. Concentrations of As, Cd, Co, Cu, Mn, Ni, Pb and Zn were determined using AAS and GF AAS, and ENAA was used for the remaining 27 elements. Results for As, Ba, Br, Ca, Cd, Ce, Co, Cr, Cs, Cu Eu, Fe, Hf, I, In, K, La, Mn, Mo, Na, Nd, Ni, Pb, Rb, Sb, Sc, Sm, Sr, Ta, Tb, Th, Ti, U, V and Zn are reported for the first time for soils from this region. The results show that concentrations of most elements were little affected by the industrial and other anthropogenic activities performed in region. Except for distinctly higher levels of Pb, Cu, Cd and Zn in Istanbul district than the median values for the Thrace region, the observed distributions seem to be mainly associated with lithogenic variations. Spatial distributions of As, Cd, Cr, Cu, Ni, Pb and Zn were plotted in relation to the concentration values in soil using Geographic Information System (GIS) technology     

抚顺市PM10中元素分布特征及来源分析

为了确定抚顺市PM10中元素的浓度特征及其来源,于2006—2007年的采暖季、风沙季和非采暖季在抚顺市的6个采样点采集PM10样品,并用等离子体原子发射光谱法(ICP-AES)测定样品中Ti、Al、Mn、Mg、Ca、Na、K、Cu、Zn、As、Pb、Cr、Ni、Co、Cd、Fe、V等17种元素的含量。结果表明,Al、Mg、Ca、Na、K、Mn、Fe等地壳元素在17种元素中占有较大比重,全年平均达到97.0%。富集因子分析结果表明,Cu、Zn、Pb、Cr、Co、Cd等元素在各季和各采样点明显受到人为活动影响,是典型的污染元素。主因子分析结果显示,土壤风沙尘、建筑尘、燃煤尘、道路扬尘、机动车尾气排放、金属冶炼、锰、铜、钛工业源是抚顺市PM10中元素的主要来源。     

Determination of Pb(II), Zn(II), Cd(II), and Co(II) ions by flame atomic absorption spectrometry in food and water samples after preconcentration by coprecipitation with Mo(VI)-diethyldithiocarbamate

A new, simple, and rapid separation and preconcentration procedure, for determination of Pb(II), Cd(II), Zn(II), and Co(II) ions in environmental real samples, has been developed. The method is based on the combination of coprecipitation of analyte ions by the aid of the Mo(VI)–diethyldithiocarbamate–(Mo(VI)-DDTC) precipitate and flame atomic absorption spectrometric determinations. The effects of experimental conditions like pH of the aqueous solution, amounts of DDTC and Mo(VI), standing time, centrifugation rate and time, sample volume, etc. and also the influences of some foreign ions were investigated in detail on the quantitative recoveries of the analyte ions. The preconcentration factors were found to be 150 for Pb(II), Zn(II) and Co(II), and 200 for Cd(II) ions. The detection limits were in the range of 0.1–2.2 μg L^?1 while the relative standard deviations were found to be lower than 5 % for the studied analyte ions. The accuracy of the method was checked by spiked/recovery tests and the analysis of certified reference material (CRM TMDW-500 Drinking Water). The procedure was successfully applied to seawater and stream water as liquid samples and baby food and dried eggplant as solid samples in order to determine the levels of Pb(II), Cd(II), Zn(II), and Co(II) ions.     

SEC-ICP-MS studies for elements binding to different molecular weight fractions of humic substances in compost extract obtained from urban solid waste

In this work, the speciation of elements in compost was studied with emphasis on their binding to humic substances. In order to assess the distribution of As, Cd, Co, Cr, Cu, Mn, Mo, Ni, Pb, U, Th and Zn among molecular weight fractions of humic substances, the compost extract (extracted by 0.1 mol l(-1) sodium pyrophosphate) was analyzed by size exclusion chromatography coupled on-line with UV-Vis spectrophotometric and ICP-MS detection. Similar chromatograms were obtained for standard humic acid (Fluka) and for compost extract (254 nm, 400 nm) and three size fractions were operationally defined that corresponded to the apparent molecular weight ranges > 15 kDa, 1-15 kDa and < 1 kDa. The percentage of total element content in compost that was leached to the extract ranged from 30% up to 100% for different elements. The elution profiles of Co, Cr, Cu, Ni and Pb (ICP-MS) followed that of humic substances, while for other elements the bulk elution peak matched the retention time observed for the element in the absence of compost extract. Spiking experiments were carried out to confirm elements' binding and to estimate the affinity of individual elements for humic substances derived from compost. The results obtained indicated the following order of decreasing affinity: Cu > Ni > Co > Pb > Cd > (Cr, U, Th) > (As, Mn, Mo, Zn). After standard addition, further binding of Cu, Ni and Co with the two molecular weight fractions of humic substances was observed, indicating that humic substances derived from compost were not saturated with these elements.     

Assessment of heavy metal enrichment in the offshore fine-grained sediments of the Caspian Sea

Sampling of the offshore seabed sediments of southwestern part of the Caspian Sea was carried out by gravity corer in order to study heavy metal concentration and the physicochemical factors controlling their distribution in the fine-grained fraction. The grain size distribution, amount, and type of clay minerals, total organic carbon (TOC) content, and Eh–pH of the sediments were determined. The average concentrations of the heavy metals in ppm are Mn (563), Cu (207.5), Sr (187), Zn (94), Pb (26.3), Ni (14.5), Co (11.5), Cd (2.56), and Ag (1.04) in their order of abundances. Co and Zn mostly indicate increase in silt-size fraction of the sediments suggesting their probable detrital provenance but the Mn, Ni, Cu, Sr, Pb, Cd, and Ag concentrations show a similar trend to distribution of the clay-size fraction. The concentrations of Mn, Co, and Cd increase with increase in the TOC content but the Cu, Pb, Ni, Ag, and Sr concentrations decrease with increase of the TOC content. The amounts of Zn, Cu, Sr, Pb, Cd, and Ag increase with increase in the CaCO₃ content. The calculated enrichment factor indicates that the sediments are very strong to extremely enriched in Ag, significantly enriched in Cu and Cd, and depleted to mineral for Pb, Sr, Co, Ni, and Zn. Variations of the Cu, Sr, Cd, Ag, and Pb concentrations are similar to the clay and CaCO₃ distributions.     

Assessment of heavy metal levels in sediment samples of Kapulukaya Dam Lake (Kirikkale) and lower catchment area

In this study, the concentrations of 13 elements (Al, Fe, Mn, Cr, Ni, Zn, Co, As, Pb, Cu, Mo, Hg, and Cd) were determined in the sediments of three different sites in the Kapulukaya Dam Lake between May 2007 and November 2008. They ranged from 1.47 to 4.64 for Al, 0.92 to 3.48 for Fe (in percent), 326.60 to 1053.00 for Mn, 98.00 to 1,116.00 for Cr, 24.70 to 127.10 for Ni, 14.80 to 124.20 for Zn, 11.0 to 43.20 for Co, 5.00 to 29.30 for Cu, 9.10 to 69.70 for As, 8.60 to 34.00 for Pb, 2.50 to 5.20 for Mo, 1.00 to 1.60 for Hg, and 0.50 to1.80 for Cd in microgram per gram dry weight sediment. The contamination degree of the sediment was assessed on the basis of enrichment factor and corresponding sediment quality guideline. The calculated enrichment factors (EF, measured metal vs. background concentrations) indicated that the effect of man-made activities on the occurrence of concentrations could be accounted for the majority of heavy metals namely Mn, As, Ni, Cu, Zn, Cr, Co, Mo, and Cd, whereas such affect was not detected for Hg and Pb. The maximum values of the EF were represented by As, minimum values by Hg at all sites. Mean EF values were 36.60 and 0.70 for As and Hg, respectively. This study has clearly assessed a certain level of heavy metal pollution in the region, based particularly on the findings from sediment.     

微波消解-电感耦合等离子体质谱法同时测定废水中20种元素

采用微波消解-电感耦合等离子体质谱法,同时测定了废水中Be、V、Cr、Mn、Co、Ni、Cu、Zn、As、Se、Mo、Ag、Cd、Sb、Ba、Hg、Tl、Pb、Th、U等20种元素,比较了5种不同消解体系对废水样品的加标回收结果,确定采用硝酸+过氧化氢消解体系。Hg在0.050μg/L～2.00μg/L、其他元素在5.00μg/L～500μg/L范围内线性良好,检出限为0.01μg/L～0.2μg/L,国家有证标准物质的测定结果符合要求,废水样品平行测定的RSD为2.6%～6.5%,加标回收率为84%～110%。     

Source discrimination of heavy metals in sediment and water of To Lich River in Hanoi City using multivariate statistical approaches

The concentrations of Mn, Fe, Ni, Cr, Cu, Pb, Zn, As, and Cd were determined to evaluate the level of contamination of To Lich River in Hanoi City. All metal concentrations in 0–10-cm water samples, except Mn, were lower than the maximum permitted concentration for irrigation water standard. Meanwhile, concentrations of As, Cd, and Zn in 0–30-cm sediments were likely to have adverse effects on agriculture and aquatic life. Sediment pollution assessment was undertaken using enrichment factor and geoaccumulation index (I _geo). The I _geo results indicated that the sediment was not polluted with Cr, Mn, Fe, and Ni, and the pollution level increased in the order of Cu < Pb < Zn < As < Cd. Meanwhile, significant enrichment was shown for Cd, As, Zn, and Pb. Cluster and principal component analyses suggest that As and Mn in sediment were derived from both lithogenic and anthropogenic sources, while Cu, Pb, Zn, Cr, Cd, and Ni originated from anthropogenic sources such as vehicular fumes for Pb and metallic discharge from industrial sources and fertilizer application for other metals.     

Multielement analysis in the fish hepatic cytosol as a screening tool in the monitoring of natural waters

The possibility of direct measurement of trace elements in hepatic cytosol of European chub (Squalius cephalus) by high-resolution inductively coupled plasma mass spectrometry (HR ICP-MS) after cytosol dilution with Milli-Q water and subsequent acidification was investigated. Due to low detection limits of this procedure, determination of 13 elements (As, Cd, Co, Cu, Fe, Mn, Mo, Pb, Sb, Sn, Sr, V and Zn) was possible in the chub hepatic cytosol, exhibiting excellent measurement repeatability in duplicates. Some of these elements were also measured by HR ICP-MS in acid digested cytosols (Cd, Co, Cu, Fe, Mn, Mo, Sr, V and Zn). Good agreement of the results obtained after sample dilution and sample digestion indicated that complex organic matrix of hepatic cytosol did not affect measurement reliability. Cytosolic concentrations of 13 trace elements in the chub liver were quantified in the following order: Fe, Zn>Cu>Mn>Mo>Sr, V, Cd>Co>As, Pb>Sn>Sb. Unlike Cd, Cu, Fe, Mn and Zn for which the cytosolic concentrations were previously reported after measurement by AAS, cytosolic concentrations of eight additional trace elements characteristic for the liver of chubs inhabiting the low contaminated river water were reported here for the first time (in nanogrammes per gramme)—Mo, 136.8–183.6; Sr, 32.7–63.0; V, 17.5–69.0; Co, 24.3–30.7; As, 9.9–29.5; Pb, 5.8–35.6; Sn, 5.5–12.4; and Sb, 0.9–2.6. The simultaneous measurement of large number of trace elements in the cytosolic fractions of fish tissues, which comprise potentially metal-sensitive sub-cellular pools, could be beneficial as a screening tool in the monitoring of natural waters, because it would enable timely recognition of increased fish exposure to metals.     

Vertical distribution of heavy metals in soil profile in a seasonally waterlogging agriculture field in Eastern Ganges Basin

The accumulation of heavy metals in soil and water is a serious concern due to their persistence and toxicity. This study investigated the vertical distribution of heavy metals, possible sources and their relation with soil texture in a soil profile from seasonally waterlogged agriculture fields of Eastern Ganges basin. Fifteen samples were collected at ～0.90-m interval during drilling of 13.11 mbgl and analysed for physical parameters (moisture content and grain size parameters: sand, silt, clay ratio) and heavy metals (Fe, Mn, Cr, Cu, Pb, Zn, Co, Ni and Cd). The average metal content was in the decreasing order of Fe?>?Mn?>?Cr?>?Zn?>?Ni?>?Cu?>?Co?>?Pb?>?Cd. Vertical distribution of Fe, Mn, Zn and Ni shows more or less similar trends, and clay zone records high concentration of heavy metals. The enrichment of heavy metals in clay zone with alkaline pH strongly implies that the heavy metal distributions in the study site are effectively regulated by soil texture and reductive dissolution of Fe and Mn oxy-hydroxides. Correlation coefficient analysis indicates that most of the metals correlate with Fe, Mn and soil texture (clay and silt). Soil quality assessment was carried out using geoaccumulation index (I _geo), enrichment factor (EF) and contamination factor (CF). The enrichment factor values were ranged between 0.66 (Mn) and 2.34 (Co) for the studied metals, and the contamination factor values varied between 0.79 (Mn) and 2.55 (Co). Results suggest that the elements such as Cu and Co are categorized as moderate to moderately severe contamination, which are further confirmed by I _geo values (0.69 for Cu and 0.78 for Co). The concentration of Ni exceeded the effects-range median values, and the biological adverse effect of this metal is 87 %. The average concentration of heavy metals was compared with published data such as concentration of heavy metals in Ganga River sediments, Ganga Delta sediments and upper continental crust (UCC), which apparently revealed that heavy metals such as Fe, Mn, Cr, Pb, Zn and Cd are influenced by the dynamic nature of flood plain deposits. Agricultural practice and domestic sewage are also influenced on the heavy metal content in the study area.     

The application of ICP-SMS, GF-AAS and HG-AFS to the analysis of water and sediment samples from a temperate stratified estuary

Three atomic spectrometry techniques, namely sector field inductively coupled plasma mass spectroscopy, graphite furnace atomic absorption spectrometry and hydride generation atomic fluorescence spectroscopy (ICP-SMS, GF-AAS and HG-AFS, respectively), housed at separate independent laboratories, were used to analyse water and sediment samples collected from the Huon River Estuary, SE Tasmania (Australia) in the Austral spring 1998. A dithiocarbamate-chelation/back-extraction technique was used to separate and preconcentrate Co, Ni, Cu, Zn, Cd and Pb from eight collected water samples prior to analysis by ICP-SMS and GF-AAS. A number of other elements in the waters were analysed directly (Mn, Fe and Zn by GF-AAS; As by HG-AFS), or following sample dilution (1 + 19: V, Mn, Fe, As, Mo, Ba and U by ICP-SMS). Where possible, previously corroborated GF-AAS and HG-AFS techniques were used to verify obtained ICP-SMS results. From the analysis of four reference waters (SLEW-1 and -2, SLRS-3 and NASS-5), good agreement, to within +/- 10-20%, was typically found between certified (or information only values) and measured results (irrespective of analytical technique). Exceptions included Zn (and sometimes Fe) that could not be quantified by ICP-SMS due to elevated blank signals, and As which was found to lie below ICP-SMS detection limits. For Huon Estuary water samples, inter-method agreement was within +/- 10-20% (for those elements amenable to analysis by more than one technique). Nitric acid extracts of two certified reference materials (Buffalo River Sediment and BCSS-1) and six Huon Estuary sediments were analysed by ICP-SMS (for Al, Sc, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Cd and Pb) and HG-AFS (for As). Results from the certified reference materials indicated extraction efficiencies of 60 70% (for most elements). A close correlation between ICP-SMS and HG-AFS was obtained for leachable As in the sediments. In terms of potential inorganic contaminants, the Huon Estuary was found to be a relatively 'clean' water system. The elemental concentrations measured in water and sediment samples from this region were found to lie within current Australian guidelines for estuaries. In general, no one analytical technique was able to accurately determine all elements in all samples from this relatively pristine estuarine environment. A combination of all three analytical techniques was necessary for the successful analysis of the elements considered in this study.     

ICP－AES光谱法同时测定团体废物浸出液中的多种金属元素

采用翻转振荡方式以水为浸提剂浸提钢渣、尾矿渣、铬渣、铅渣、粉煤灰和电镀污泥试样，过滤后的浸提液经ＤＤＴＣ／ＣＣｌ４体系萃取富集后，用ＩＣＰ－ＡＥＳ法同时测定了Ｃｕ、Ｐｂ、Ｚｎ、Ｃｄ、Ｎｉ、Ｆｅ、Ｍｎ、Ｃｏ和Ｖ等多种金属元素．方法具有较好的精密度和准确度，宜于推广应用。     

Distribution and accumulation of heavy metals in the sediments of Akkaya Dam,Nigde, Turkey

Twenty-one surface sediment samples were collected from Akkaya Dam. Heavy metal concentrations (Mo, Cu, Pb, Zn, Ni, Co, Mn, Fe, Cr, As, V and Cd), grain size, organic carbon and carbonate contents were studied in order to assess the extent of environmental pollution and to discuss the origin of these contaminants in sediments of dam. The sediments in the study area are mostly very fine sands. However, mud was observed in the northeast of the dam. Sediment pollution assessment was carried out using enrichment factor. The calculation of enrichment factors showed that Mo is depleted by 1.0 whereas Cu, Pb, Zn, Ni, Co, Mn, As, V, Cr and Cd are enriched by 3, 5.4, 7, 2.7, 2.2, 3.4, 42.3, 2.1, 1.8 and 7.2, respectively. Relatively high concentrations heavy metals occurred in north (textile industry area) and east (Karasu River) due to enrichment controlled by anthropogenic wastes. The results of correlation analysis show low–medium positive and negative correlations among metals, grain size, carbonate contents and organic carbon and indicate that heavy metals in sediments of the Akkaya Dam have different anthropogenic sources.     

Heavy Metals Monitoring using Bivalves from Mediterranean Sea and Red Sea

The concentrations of heavy metals (Cd, Co, Cu, Fe, Mn, Ni, Pd and Zn) were measured in the Bivalves (Modiolus auriculatus and Donax trunculus) collected from the Egyptian coasts of Mediterranean Sea and Brachiodonates sp. from the Egyptian coasts of Red Sea. The average concentrations of the heavy metals analyzed exhibited the following decreasing order: Fe > Zn > Cu > Mn > Ni > Co > Pb > Cd for both Mediterranean Sea and Red Sea. The analyses of Cd, Co, Ni, Pb, and Zn showed higher average concentrations for samples collected from Red Sea than that collected from Mediterranean Sea, while Fe, Cu and Mn showed the reverse results. Fe was used as a normalizing agent for all studied metals and exhibited presence of two locations from each of Mediterranean Sea and Red Sea have anthropogenic inputs of heavy metals. These results suggest that the coastal area in both Mediterranean Sea and Red Sea of Egypt might be considered relatively unpolluted with heavy metal.