Managing emissions from highly industrialized areas: Regulatory compliance under uncertainty

The use of regulatory and compliance-based modeling for air quality impact assessment is invariably relied upon to predict future air quality under various management scenarios particularly where air quality monitoring data are limited. This paper examines the dispersion from a multi-stack cement manufacturing complex with associated quarries and transport activities for regulatory compliance under uncertain emission and meteorological conditions. The concentrations of CO, NO_x, SO₂ and PM at sensitive receptor locations were used as indicators in comparison to World Health Organization (WHO) interim guidelines. Exceedance exposure areas were delineated under bounded uncertainties in input emission factors and meteorological parameters. Planning and management initiatives were tested to control/minimize potential exposure. Compared to the case of low emissions and actual meteorological conditions, the consideration of worst emissions coupled to worst meteorological conditions enlarged the boundaries of the exceedance exposure areas considerably. The implementation of best available technologies and enforcement of emission standards improved air quality in the region significantly and lowered the exposure at many population centers to below health standards. Uncertainty in the output of atmospheric dispersion models continues to play a significant role to be considered at the point where science is translated into political decision making.     

Resolving the interactions between population density and air pollution emissions controls in the San Joaquin Valley,USA

The effectiveness of emissions control programs designed to reduce concentrations of airborne particulate matter with an aerodynamic diameter <2.5 μm (PM_2.5) in California's San Joaquin Valley was studied in the year 2030 under three growth scenarios: low, medium, and high population density. Base-case inventories for each choice of population density were created using a coupled emissions modeling system that simultaneously considered interactions between land use and transportation, area source, and point source emissions. The ambient PM_2.5 response to each combination of population density and emissions control was evaluated using a regional chemical transport model over a 3-week winter stagnation episode. Comparisons between scenarios were based on regional average and population-weighted PM_2.5 concentrations. In the absence of any emissions control program, population-weighted concentrations of PM_2.5 in the future San Joaquin Valley are lowest under growth scenarios that emphasize low population density. A complete ban on wood burning and a 90% reduction in emissions from food cooking operations and diesel engines must occur before medium- to high-density growth scenarios result in lower population-weighted concentrations of PM_2.5. These trends partly reflect the fact that existing downtown urban cores that naturally act as anchor points for new high-density growth in the San Joaquin Valley are located close to major transportation corridors for goods movement. Adding growth buffers around transportation corridors had little impact in the current analysis, since the 8-km resolution of the chemical transport model already provided an artificial buffer around major emissions sources.

Assuming that future emissions controls will greatly reduce or eliminate emissions from residential wood burning, food cooking, and diesel engines, the 2030 growth scenario using “as-planned” (medium) population density achieves the lowest population-weighted average PM_2.5 concentration in the future San Joaquin Valley during a severe winter stagnation event.

Implications: The San Joaquin Valley is one of the most heavily polluted air basins in the United States that are projected to experience strong population growth in the coming decades. The best plan to improve air quality in the region combines medium- or high-density population growth with rigorous emissions controls. In the absences of controls, high-density growth leads to increased population exposure to PM_2.5 compared with low-density growth scenarios (urban sprawl).     

Evaluating carbon emissions of China’s waste management strategies for building refurbishment projects: contributing to a circular economy

This study evaluates carbon emissions of construction and demolition (C&D) waste generated by building refurbishment, using a life cycle assessment approach through a case study project in China. Three waste management scenarios were developed for a building refurbishment project in the city of Suzhou. Scenario 1 is under the business-as-usual C&D waste management practice in China; scenario 2 is based on the open-ended 3R strategy, which focuses on the downstream impact of waste; and scenario 3 considers both the upstream and downstream impact of waste. The results reveal that the composition of the waste generated from building refurbishment projects is different from construction and demolition projects. In the life cycle of C&D waste management of building refurbishment projects, the refurbishment material stage generates the highest carbon emissions compared to the dismantlement, refurbishment construction, and refurbishment material end of life stages. Scenario 1 produces higher carbon emissions than scenario 2, but the difference is not significant in the whole life cycle of the building refurbishment project, whereas carbon emissions for scenario 3 are significantly less than both scenario 1 and scenario 2. The study finds the reason for this difference is that scenario 1 and scenario 2 are based on a linear economy that relies on unsustainable demand for raw materials, whereas scenario 3 is based on a circular economy that uses upcycled materials to substitute for raw materials and considers waste management from a cradle to cradle perspective. This study fills a research gap by evaluating carbon emissions of different waste management strategies for building refurbishment projects, which are expected to be an increasing portion of overall construction activity in China for the foreseeable future.

     

An evaluation of public health impact of ambient air pollution under various energy scenarios in Shanghai,China

To investigate the potential public health impact of ambient air pollution under various energy scenarios in Shanghai, we estimated the air pollution exposure level of the general population under various planned energy scenarios, and assessed the potential public health impact using the concentration–response functions derived from available epidemiologic studies. The results show that ambient air pollution in relation to various energy scenarios could have significant impact on the health status of Shanghai residents. Compared with base case scenario, implementation of various energy scenarios could prevent 608–5144 and 1189–10,462 PM₁₀-related avoidable deaths (mid-value) in 2010 and 2020, respectively; and it could also decrease substantial cases of relevant diseases. These findings illustrate that an effective energy and environmental policy will play an active role in reduction of air pollutant emissions, improvement of air quality, and public health.     

The impact of CO2 capture in the power and heat sector on the emission of SO2, NOx,particulate matter,volatile organic compounds and NH3 in the European Union

This study quantifies the trade-offs and synergies between climate and air quality policy objectives for the European power and heat (P&H) sector. An overview is presented of the expected performance data of CO₂ capture systems implemented at P&H plants, and the expected emission of key air pollutants, being: SO₂, NO_X, NH₃, volatile organic compounds (VOCs) and particulate matter (PM). The CO₂ capture systems investigated include: post-combustion, oxyfuel combustion and pre-combustion capture.For all capture systems it was found that SO₂, NO_x and PM emissions are expected to be reduced or remain equal per unit of primary energy input compared to power plants without CO₂ capture. Increase in primary energy input as a result of the energy penalty for CO₂ capture may for some technologies and substances result in a net increase of emissions per kWh output. The emission of ammonia may increase by a factor of up to 45 per unit of primary energy input for post-combustion technologies. No data are available about the emission of VOCs from CO₂ capture technologies.A simple model was developed and applied to analyse the impact of CO₂ capture in the European P&H sector on the emission level of key air pollutants in 2030. Four scenarios were developed: one without CO₂ capture and three with one dominantly implemented CO₂ capture system, varying between: post-combustion, oxyfuel combustion and pre-combustion.The results showed a reduction in GHG emissions for the scenarios with CO₂ capture compared to the baseline scenario between 12% and 20% in the EU 27 region in 2030. NO_x emissions were 15% higher in the P&H sector in a scenario with predominantly post-combustion and lower when oxyfuel combustion (?16%) or pre-combustion (?20%) were implemented on a large scale. Large scale implementation of the post-combustion technology in 2030 may also result in significantly higher, i.e. increase by a factor of 28, NH₃ emissions compared to scenarios with other CO₂ capture options or without capture. SO₂ emissions were very low for all scenarios that include large scale implementation of CO₂ capture in 2030, i.e. a reduction varying between 27% and 41%. Particulate Matter emissions were found to be lower in the scenarios with CO₂ capture. The scenario with implementation of the oxyfuel technology showed the lowest PM emissions followed by the scenario with a significant share allocated to pre-combustion, respectively ?59% and ?31%. The scenario with post-combustion capture resulted in PM emissions varying between 35% reduction and 26% increase.     

Assessment of the emissions and air quality impacts of biomass and biogas use in California

It is estimated that there is sufficient in-state “technically” recoverable biomass to support nearly 4000 MW of bioelectricity generation capacity. This study assesses the emissions of greenhouse gases and air pollutants and resulting air quality impacts of new and existing bioenergy capacity throughout the state of California, focusing on feedstocks and advanced technologies utilizing biomass resources predominant in each region. The options for bioresources include the production of bioelectricity and renewable natural gas (NG). Emissions of criteria pollutants and greenhouse gases are quantified for a set of scenarios that span the emission factors for power generation and the use of renewable natural gas for vehicle fueling. Emissions are input to the Community Multiscale Air Quality (CMAQ) model to predict regional and statewide temporal air quality impacts from the biopower scenarios. With current technology and at the emission levels of current installations, maximum bioelectricity production could increase nitrogen oxide (NO_x) emissions by 10% in 2020, which would cause increases in ozone and particulate matter concentrations in large areas of California. Technology upgrades would achieve the lowest criteria pollutant emissions. Conversion of biomass to compressed NG (CNG) for vehicles would achieve comparable emission reductions of criteria pollutants and minimize emissions of greenhouse gases (GHG). Air quality modeling of biomass scenarios suggest that applying technological changes and emission controls would minimize the air quality impacts of bioelectricity generation. And a shift from bioelectricity production to CNG production for vehicles would reduce air quality impacts further. From a co-benefits standpoint, CNG production for vehicles appears to provide the best benefits in terms of GHG emissions and air quality.

Implications:?This investigation provides a consistent analysis of air quality impacts and greenhouse gas emissions for scenarios examining increased biomass use. Further work involving economic assessment, seasonal or annual emissions and air quality modeling, and potential exposure analysis would help inform policy makers and industry with respect to further development and direction of biomass policy and bioenergy technology alternatives needed to meet energy and environmental goals in California.     

Modeling Analyses of the Effects of Changes in Nitrogen Oxides Emissions from the Electric Power Sector on Ozone Levels in the Eastern United States

Abstract

In this paper, we examine the changes in ambient ozone concentrations simulated by the Community Multiscale Air Quality (CMAQ) model for summer 2002 under three different nitrogen oxides (NO_x) emission scenarios. Two emission scenarios represent best estimates of 2002 and 2004 emissions; they allow assessment of the impact of the NO_x emissions reductions imposed on the utility sector by the NO_x State Implementation Plan (SIP) Call. The third scenario represents a hypothetical rendering of what NO_x emissions would have been in 2002 if no emission controls had been imposed on the utility sector. Examination of the modeled median and 95th percentile daily maximum 8-hr average ozone concentrations reveals that median ozone levels estimated for the 2004 emission scenario were less than those modeled for 2002 in the region most affected by the NO_x SIP Call. Comparison of the “no-control” with the “2002” scenario revealed that ozone concentrations would have been much higher in much of the eastern United States if the utility sector had not implemented NO_x emission controls; exceptions occurred in the immediate vicinity of major point sources where increased NO titration tends to lower ozone levels.     

Current and future emission estimates of exhaust gases and particles from shipping at the largest port in Korea

The emissions of exhaust gases (NO _x , SO₂, VOCs, and CO₂) and particles (e.g., PM) from ships traversing Busan Port in Korea were estimated over three different years (the years 2006, 2008, and 2009). This analysis was performed according to the ship operational modes (“at sea,” “maneuvering,” and “in port”) and ship types based on an activity-based method. The ship emissions for current (base year 2009) and future scenarios (years 2020 and 2050) were also compared. The annual emissions of SO₂, VOCs, PM, and CO₂ were highest (9.6?×?10³, 374, 1.2?×?10³, and 5.6?×?10⁵ ton year^?1, respectively) in 2008. In contrast, the annual NO _x emissions were highest (11.7?×?10³ ton year^?1) in 2006 due mainly to the high NO _x emission factor. The emissions of air pollutants for each ship operational mode differed considerably, with the largest emission observed in “in port” mode. In addition, the largest fraction (approximately 45–67 %) of the emissions of all air pollutants during the study period was emitted from container ships. The future ship emissions of most pollutants (except for SO₂ and PM) in 2020 and 2050 are estimated to be 1.4–1.8 and 4.7–6.1 times higher than those in 2009 (base year), respectively.     

Air Pollution Emissions from Increased Industrial Coal Use in the Northeastern United States

Evaluating the air pollution impacts of energy use in the industrial sector is difficult because of the diversity and multiplicity of sources and a general lack of systematic, up-to-date data collection mechanisms. Fuel-specific energy consumption for a multi-state region is provided by the U.S. Department of Energy PIES model for a base year (1975), together with scenarios for future years. A computer model developed in this study—the Sub-regional Energy and Emissions Model (SEEM)—is applied to disaggregate the regional industrial figures to the county level according to fuel type and industrial category at the two-digit SIC level. The resulting emissions of total suspended particulates (TSP) and sulfur dioxide (SO₂) for all industrial categories are estimated at the county level by Incorporating county-specific air pollution regulations in SEEM, and are then aggregated to larger geographical regions. The model has been applied to evaluate the increased air pollution impacts of industrial energy use in the northeastern United States for two alternative 1990 scenarios: (1) the midrange/trendlong PIES projections, and (2) a Coal Replacement Scenario, which assumes a higher percentage of fuel burned in new boilers will be coal. The results are discussed in terms of implications for air pollution control policy.     

Expected ozone benefits of reducing nitrogen oxide (NOx) emissions from coal-fired electricity generating units in the eastern United States

On hot summer days in the eastern United States, electricity demand rises, mainly because of increased use of air conditioning. Power plants must provide this additional energy, emitting additional pollutants when meteorological conditions are primed for poor air quality. To evaluate the impact of summertime NO_x emissions from coal-fired electricity generating units (EGUs) on surface ozone formation, we performed a series of sensitivity modeling forecast scenarios utilizing EPA 2018 version 6.0 emissions (2011 base year) and CMAQ v5.0.2. Coal-fired EGU NO_x emissions were adjusted to match the lowest NO_x rates observed during the ozone seasons (April 1–October 31) of 2005–2012 (Scenario A), where ozone decreased by 3–4 ppb in affected areas. When compared to the highest emissions rates during the same time period (Scenario B), ozone increased ～4–7 ppb. NO_x emission rates adjusted to match the observed rates from 2011 (Scenario C) increased ozone by ～4–5 ppb. Finally in Scenario D, the impact of additional NO_x reductions was determined by assuming installation of selective catalytic reduction (SCR) controls on all units lacking postcombustion controls; this decreased ozone by an additional 2–4 ppb relative to Scenario A. Following the announcement of a stricter 8-hour ozone standard, this analysis outlines a strategy that would help bring coastal areas in the mid-Atlantic region closer to attainment, and would also provide profound benefits for upwind states where most of the regional EGU NO_x originates, even if additional capital investments are not made (Scenario A).

Implications: With the 8-hr maximum ozone National Ambient Air Quality Standard (NAAQS) decreasing from 75 to 70 ppb, modeling results indicate that use of postcombustion controls on coal-fired power plants in 2018 could help keep regions in attainment. By operating already existing nitrogen oxide (NO_x) removal devices to their full potential, ozone could be significantly curtailed, achieving ozone reductions by up to 5 ppb in areas around the source of emission and immediately downwind. Ozone improvements are also significant (1–2 ppb) for areas affected by cross-state transport, especially Mid-Atlantic coast regions that had struggled to meet the 75 ppb standard.     

Air Quality Impacts of Distributed Energy Resources Implemented in the Northeastern United States

Abstract

Emissions from the potential installation of distributed energy resources (DER) in the place of current utility-scale power generators have been introduced into an emissions inventory of the northeastern United States. A methodology for predicting future market penetration of DER that considers economics and emission factors was used to estimate the most likely implementation of DER. The methodology results in spatially and temporally resolved emission profiles of criteria pollutants that are subsequently introduced into a detailed atmospheric chemistry and transport model of the region. The DER technology determined by the methodology includes 62% reciprocating engines, 34% gas turbines, and 4% fuel cells and other emerging technologies. The introduction of DER leads to retirement of 2625 MW of existing power plants for which emissions are removed from the inventory. The air quality model predicts maximum differences in air pollutant concentrations that are located downwind from the central power plants that were removed from the domain. Maximum decreases in hourly peak ozone concentrations due to DER use are 10 ppb and are located over the state of New Jersey. Maximum decreases in 24-hr average fine particulate matter (PM_2.5) concentrations reach 3 μg/m3 and are located off the coast of New Jersey and New York. The main contribution to decreased PM_2.5 is the reduction of sulfate levels due to significant reductions in direct emissions of sulfur oxides (SO_x) from the DER compared with the central power plants removed. The scenario presented here represents an accelerated DER penetration case with aggressive emission reductions due to removal of highly emitting power plants. Such scenario provides an upper bound for air quality benefits of DER implementation scenarios.     

The Australian Air Quality Forecasting System: The Use of Green Scenarios of Motor Vehicle Usage as an Educational Tool

Abstract

The Australian Air Quality Forecasting System (AAQFS) is one of several newly emerging, high-resolution, numerical air quality forecasting systems. The system is briefly described. A public education application of the air quality impact of motor vehicle usage is explored by computing the concentration and dosage of particulate matter less than 10 µm in aerodynamic diameter (PM₁₀) for a commuter traveling to work between Geelong and Melbourne, Victoria, Australia, under “business-as-usual” and “green” scenarios. This application could be routinely incorporated into systems like AAQFS. Two methodologies for calculating the dosage are described: one for operational use and one for more detailed applications. The Clean Air Research Programme-Personal Exposure Study in Melbourne provides support for this operational methodology. The more detailed methodology is illustrated using a system for predicting concentrations due to near-road emissions of PM₁₀ andapplied in Sydney.     

Influence of regional development policies and clean technology adoption on future air pollution exposure

Future air pollution emissions in the year 2030 were estimated for the San Joaquin Valley (SJV) in central California using a combined system of land use, mobile, off-road, stationary, area, and biogenic emissions models. Four scenarios were developed that use different assumptions about the density of development and level of investment in transportation infrastructure to accommodate the expected doubling of the SJV population in the next 20 years. Scenario 1 reflects current land-use patterns and infrastructure while scenario 2 encouraged compact urban footprints including redevelopment of existing urban centers and investments in transit. Scenario 3 allowed sprawling development in the SJV with reduced population density in existing urban centers and construction of all planned freeways. Scenario 4 followed currently adopted land use and transportation plans for the SJV. The air quality resulting from these urban development scenarios was evaluated using meteorology from a winter stagnation event that occurred on December 15th, 2000 to January 7th 2001. Predicted base-case PM2.5 mass concentrations within the region exceeded 35 μg m^?3 over the 22-day episode. Compact growth reduced the PM2.5 concentrations by ～1 μg m^?3 relative to the base-case over most of the SJV with the exception of increases (～1 μg m^?3) in urban centers driven by increased concentrations of elemental carbon (EC) and organic carbon (OC). Low-density development increased the PM2.5 concentrations by 1–4 μg m^?3 over most of the region, with decreases (0.5–2 μg m^?3) around urban areas. Population-weighted average PM2.5 concentrations were very similar for all development scenarios ranging between 16 and 17.4 μg m^?3. Exposure to primary PM components such as EC and OC increased 10–15% for high density development scenarios and decreased by 11–19% for low-density scenarios. Patterns for secondary PM components such as nitrate and ammonium ion were almost exactly reversed, with a 10% increase under low-density development and a 5% decrease under high density development. The increased human exposure to primary pollutants such as EC and OC could be predicted using a simplified analysis of population-weighted primary emissions. Regional planning agencies should develop thresholds of population-weighted primary emissions exposure to guide the development of growth plans. This metric will allow them to actively reduce the potential negative impacts of compact growth while preserving the benefits.     

Use of Energy Scenarios in Addressing the CO2 Question

A reference scenario for CO₂ emissions was developed using a model of world energy supply and demand. In the reference scenario, world GNP and world energy demand increase at average rates of 2.1 percent per year and 1.5 percent per year, respectively during the period 1975-2100. The corresponding annual CO₂ emissions rise to a maximum of 16 gigatons of carbon around 2050 and then decline as a result of a transition to nonfossil fuel energy systems. A modified scenario for high CO₂ emissions was obtained by assuming an abundant supply of low cost coal, thus eliminating the transition. A low case was developed in which the low cost of alternative energy (i.e., solar, nuclear) induces an earlier shift away from fossil fuels.

Annual emissions of the three scenarios were used as input to a global carbon cycle model and the CO₂ buildup in the atmosphere during the period 1980-2100 was determined by the model. All three scenarios showed continuous rises in atmospheric CO₂ concentration. The reference scenario reached 775 ppm by 2100. The high CO₂ case resulted in concentrations of over 1040 ppm, and for the low case the 2100 concentration was just under 700 ppm. If the climate theory is correct, even 700 ppm is sufficient to give significant climate warming, but by experiencing the change gradually over a century, adaptation may not be painful. An early transition to nonfossil fuel supplies makes the problem less severe but does not eliminate it.     

Computation of uncertainty for atmospheric emission projections from key pollutant sources in Spain

Emission projections are important for environmental policy, both to evaluate the effectiveness of abatement strategies and to determine legislation compliance in the future. Moreover, including uncertainty is an essential added value for decision makers. In this work, projection values and their associated uncertainty are computed for pollutant emissions corresponding to the most significant activities from the national atmospheric emission inventory in Spain. Till now, projections had been calculated under three main scenarios: “without measures” (WoM), “with measures” (WM) and “with additional measures” (WAM). For the first one, regression techniques had been applied, which are inadequate for time-dependent data. For the other scenarios, values had been computed taking into account expected activity growth, as well as policies and measures. However, only point forecasts had been computed. In this work statistical methodology has been applied for: a) Inclusion of projection intervals for future time points, where the width of the intervals is a measure of uncertainty. b) For the WoM scenario, ARIMA models are applied to model the dynamics of the processes. c) In the WM scenario, bootstrap is applied as an additional non-parametric tool, which does not rely on distributional assumptions and is thus more general. The advantages of using ARIMA models for the WoM scenario including uncertainty are shown. Moreover, presenting the WM scenario allows observing if projected emission values fall within the intervals, thus showing if the measures to be taken to reach the scenario imply a significant improvement. Results also show how bootstrap techniques incorporate stochastic modelling to produce forecast intervals for the WM scenario.     

Assessment of air quality benefits from national air pollution control policies in China. Part I: Background,emission scenarios and evaluation of meteorological predictions

Under the 11th Five Year Plan (FYP, 2006–2010) for national environmental protection by the Chinese government, the overarching goal for sulfur dioxide (SO₂) controls is to achieve a total national emissions level of SO₂ in 2010 10% lower than the level in 2005. A similar nitrogen oxides (NO_x) emissions control plan is currently under development and could be enforced during the 12th FYP (2011–2015). In this study, the U.S. Environmental Protection Agency (U.S.EPA)’s Community Multi-Scale Air Quality (Models-3/CMAQ) modeling system was applied to assess the air quality improvement that would result from the targeted SO₂ and NO_x emission controls in China. Four emission scenarios — the base year 2005, the 2010 Business-As-Usual (BAU) scenario, the 2010 SO₂ control scenario, and the 2010 NO_x control scenario—were constructed and simulated to assess the air quality change from the national control plan. The Fifth-Generation NCAR/Penn State Mesoscale Model (MM5) was applied to generate the meteorological fields for the CMAQ simulations. In this Part I paper, the model performance for the simulated meteorology was evaluated against observations for the base case in terms of temperature, wind speed, wind direction, and precipitation. It is shown that MM5 model gives an overall good performance for these meteorological variables. The generated meteorological fields are acceptable for using in the CMAQ modeling.     

Estimating the effects of increased urbanization on surface meteorology and ozone concentrations in the New York City metropolitan region

Land use and pollutant emission changes can have significant impacts on air quality, regional climate, and human health. Here we describe a modeling study aimed at quantifying the potential effects of extensive changes in urban land cover in the New York City (NYC), USA metropolitan region on surface meteorology and ozone (O₃) concentrations. The SLEUTH land-use change model was used to extrapolate urban land cover over this region from “present-day” (ca. 1990) conditions to a future year (ca. 2050), and these projections were subsequently integrated into meteorological and air quality simulations. The development of the future-year land-use scenario followed the narrative of the “A2” scenario described by the Intergovernmental Panel on Climate Change (IPCC), but was restricted to the greater NYC area. The modeling system consists of the Penn State/NCAR MM5 mesoscale meteorological model; the Sparse Matrix Operator Kernal Emissions processing system; and the US EPA Community Multiscale Air Quality model, and simulations were performed for two 18-day episodes, one near-past and one future. Our results suggest that extensive urban growth in the NYC metropolitan area has the potential to increase afternoon near-surface temperatures by more than 0.6 °C and planetary boundary layer (PBL) heights by more than 150 m, as well as decrease water vapor mixing ratio by more than 0.6 g kg⁻¹, across the NYC metropolitan area, with the areal extent of all of these changes generally coinciding with the area of increased urbanization. On the other hand, the impacts of these land use changes on ozone concentrations are more complex. Simulation results indicate that future changes in urbanization, with emissions held constant, may lead to increases in episode-average O₃ levels by about 1–5 ppb, and episode-maximum 8 h O₃ levels by more than 6 ppb across much of the NYC area. However, spatial patterns of ozone changes are heterogeneous and also indicate the presence of areas with decreasing ozone concentrations. When anthropogenic emissions were increased to be consistent with the extensive urbanization in the greater NYC area, the O₃ levels increased in outer counties of the metropolitan region but decreased in others, including coastal Connecticut and the Long Island Sound area.     

Determination of air quality zones in Turkey

In this study, the particulate matter (with an aerodynamic diameter <10 μm; PM₁₀) profile of Turkey with data from the air quality monitoring stations located throughout the country was used. The number of stations (119) was reduced to 55 after a missing data treatment for statistical analyses. First, a classification method was developed based on ongoing national and international (European Commission directives) legislations to categorize air zones into six groups, from a “Very Clear Air Zone” to a “Polluted Air Zone.” Then, a Geographic Information System (GIS)-based interpolation technique and statistical analyses (correlation analysis and factor analysis) were used to generate PM₁₀ pollution profiles of the annual heating time and nonheating time periods. Finally, the coherent air pollution management zones of Turkey, based on air quality criteria and measured data using a GIS-based model supported by statistical analyses, were suggested. Based on the analysis, four hot spots were identified: (i) the eastern part of the Black Sea region; (ii) the northeastern part of inland Anatolia; (iii) the western part of Northeastern Anatolia; and (vi) the eastern part of Turkey. The possible reasons for the elevated PM₁₀ levels are discussed using topographic, climatologic, land use, and energy utilization parameters. Finally, the suggested air zones were compared with the administrative air zones, which were newly developed by the Turkish Ministry of Environment and Forestry, to evaluate the level of agreement between the two.

Implications: The evaluation of air quality profiles of specific regions is important in the development and/or application of an effective air quality management strategy. Factor analysis (FA), together with correlation analysis (CA), provides useful information to classify air pollution management areas over regional networks that have historical time-series air quality data. In this study, which relied on a FA- and CA-based methodology, the coherent air pollution management zones of Turkey after using a GIS-based model were suggested. Policy makers and scientist can use these suggested zones to construct better air quality management strategies.     

Nonmethane Organic Compound to Nitrogen Oxide Ratios and Organic Composition in Cities and Rural Areas

The observed ranges in nonmethane organic compound (NMOC) concentrations, NMOC composition and nitrogen oxides (NO_X) concentrations have been evaluated for urban and nonurban areas at ground level and aloft of the contiguous United States. The ranges in NMOC to NO_X ratios also are considered. The NMOC composition consistently shifts towards less reactive compounds, especially the alkanes, in air parcels over nonurban areas compared to the NMOC composition near ground level within urban areas. The values for the NMOC to NO_X ratios, 1.2 to 4.2, in air aloft over nonurban areas are lower than in air at ground level urban sites, ≥8, and much lower than in air at ground level nonurban sites, ≥20.

The layers of air aloft over a number of nonurban areas of the United States tend to accumulate NO_X emissions from the tall stacks of large fossil fuel power plants located at nonurban sites. During the night into the morning hours, the air aloft is isolated from any fresh NMOC emissions predominately coming from near surface sources. Conversely, during this extended period of restricted vertical mixing, air near the surface accumulates NMOC emissions while this air is isolated from the major NO_X sources emitting aloft. These differences in the distribution of NMOC and NO_X sources appear to account for the much larger NMOC to NO_X ratios reported near ground level compared to aloft over nonurban areas.

Two types of experimental results are consistent with these conclusions: (1) observed increases in surface rural NO_X concentrations during the morning hours during which the mixing depth increases to reach the altitude at which NO_X from the stacks of fossil fuel power plants is being transported downwind; (2) high correlations of total nitrate at rural locations with Se, which is a tracer for coal-fired power plant NO_X emissions.

The implications of these conclusions from the standpoint of air quality strategies are suggested by use of appropriate scenarios applied to both urban and regional scale photochemical air quality models. The predictions from urban model scenarios with NMOC to NO_X ratios up to 20 are that NO_X control will result in the need for the control of more NMOC emissions than necessary in the absence of NO_X control, in order to meet the O₃ standard. On a regional scale, control of NO_X emissions from fossil fuel power plants has little overall effect regionally but does result on a more local scale in both small decreases and increases in O₃ concentrations compared to the baseline scenario without NO_X control. The regional modeling results obtained to date suggest that NO_X control may be effective in reducing O₃ concentrations only for a very limited set of conditions in rural areas.