Fenton试剂法处理甘氨酸废水中COD的研究

通过正交试验的方法用Fenton试剂对甘氨酸生产中的工业废水进行了试验研究,分析了各因素影响程度及各影响因子的作用机理,得出了最佳的操作条件为:H2O2:COD=1.8,[Fe2 ]=40 mmol/L,反应温度40℃,pH值为3,反应时间为80 min,最终的COD去除率为68%左右.     

碱催化H2O2氧化法预处理奶牛养殖废水的试验研究

采用碱催化H2O2氧化法对奶牛养殖废水进行预处理试验,研究了温度、pH、H2O2投加量、反应时间等参数对COD去除效果的影响,确定了反应最佳运行条件。试验结果表明,碱催化H2O2氧化法在pH7~12时,对COD的去除率为40%~60%;当反应温度50℃,pH值9,H2O2投加量2.72 g/L,反应时间20 min时,COD的去除率为66.3%。     

复合垂直流人工湿地除磷正交试验研究

为了确定复合垂直流人工湿地的流程、水力负荷、pH、COD对TP去除率的影响和提高除磷效果,选择了美人蕉和风车草构建的复合垂直流人工湿地试验系统,开展除磷的正交试验研究。采用SPSS13.0软件对正交试验结果进行方差分析,确定各因素显著性及优选条件。结果表明,复合垂直流人工湿地流程、水力负荷、pH、COD对除磷效果均有影响,其中流程对TP去除率影响显著,COD对TP去除率影响不显著。各因素对TP去除率的影响程度依次为:流程水力负荷pHCOD。除磷优选条件:COD为225mg/L,pH为8,流程为1100mm,水力负荷为181.25L/(m2.d)。     

超声波、Fenton试剂与絮凝联用进一步处理焦化废水的实验研究

焦化废水是一种较难处理的工业废水,目前采用的生化方法很难使COD达到国家规定的排放标准.对超声、Fenton与絮凝联合应用处理生化后的焦化废水进行了实验研究,并探讨了三者联合应用的最佳组合反应条件及单因素对COD的影响趋势.结果表明,三者联合应用处理焦化废水COD的最佳反应条件为:Fe2 40 mg/L,H2O2 55 mg/L,FeCl3 5.4 mg/L,PAM 1.2mg/L,超声波频率为34.19 kHz.在此反应条件下,COD去除率达到77.7%;各单因素对COD去除率的影响顺序为Fe2 ＞H2O2＞PAM＞超声波频率＞FeCl3.     

多相组合膜生物反应器对精细化工废水处理的应用研究

通过多相组合膜生物反应器对精细化工废水的处理试验，分析了COD、NH3-N、TP指标的去除效果。在装置进水浓度COD为600—900mg／L、NH3-N20～40mg／L、TP2．0～6．0mg／L时，出水COD为80—120mg／L，NH3-N未检出，TP为0．5—2．0mg／L，COD的去除率稳定在87％左右，NH3-N的去除率大于99％，TP的去除率稳定在75％左右。研究表明，多相组合膜生物反应器非常适合精细化工废水的处理。     

O3、H2O2／O3及UV／O3在焦化废水深度处理中的应用

采用O3、H2O2／O3及UV／O3等高级氧化技术（AOPs）对某焦化公司的生化出水进行深度处理，考察了O3与废水的接触时间、溶液pH、反应温度等因素对废水COD去除率的影响，确定出O3氧化反应的最佳工艺参数为：接触时间40min，溶液pH8．5，反应温度25℃，此条件下废水COD及UV254的去除率最高可达47．14％和73．47％；H2O2／O3及UV／O3两种组合工艺对焦化废水COD及UV254的去除率均有一定程度的提高，但H2O2／O3系统的运行效果取决于H2O2的投加量。研究结论表明，单纯采用COD作为评价指标，并不能准确反映出O3系列AOPs对焦化废水中有机污染物的降解作用。     

同步硝化反硝化生物脱氮技术研究

讨论了影响同步硝化反硝化反应的各参数，并进行了单因素实验与正交实验，获得了同步硝化反硝化生物脱氮工艺运行的最佳条件：DO浓度控制在0．5～2mg／L，COD浓度为600～800mg／L，混合液悬浮固体（MLSS）为5000mg/L，pH值在8．0左右，反应时间为6h。在此条件下，氨氮及COD的去除率都较高，分别达85％和95％，总氮去除率为68．5％。     

Fe（Ⅱ）EDTA／H2O2电催化降解甲基橙模拟废水的研究

在无隔膜电解槽中，采用SPR（Ru—Ir—TiO2）为阳极，石墨为阴极，考察了Fe（Ⅱ）EDTA／H2O2电催化降解甲基橙（methylorange）模拟废水的影响，发现EDTA很大程度上促进了类电Fenton试剂对甲基橙模拟废水的降解。实验研究表明，在外加电压为5．0V，EDTA：Fe2＋=2：1（摩尔比，Fe2＋=40mmol／L），H202=48mmot／L，电解质Na2SO4=40mmol／L，废水pH值为（6．5±0．1）的条件下，降解260mg／L的甲基橙模拟废水90min，EDTA的加入可以使甲基橙模拟废水的脱色率由29．5％上升到78．4％，COD由571．429mg／L降至80mg／L，COD的降解率为86％，EDTA在此过程中既是催化剂又是反应物，可有效避免EDTA带来二次环境污染的可能性。     

生物膜法处理硫化铅锌矿尾矿库外排废水简

研究了生物膜法对广东省某硫化铅锌矿尾矿库外排废水的处理效果，探索不同载体，不同COD浓度对生物膜法降解COD的影响。结果表明，高浓度的COD对生物膜法处理选矿废水有影响，在6~13℃的条件下，水力停留时间为2 d时，以50 cm×25 cm×0.4 cm的黏胶材料生物载体作为挂膜载体，处理50 L硫化铅锌矿尾矿库外排废水取得了良好效果，出水COD浓度稳定在40 mg/L左右，出水达到《铅、锌工业污染物排放标准》（GB25466-2010）的要求。     

UV-Fenton光催化氧化处理高浓度邻苯二甲酸二辛酯生产废水

采用UV-Fenton技术光催化氧化高浓度邻苯二甲酸二辛酯（DOP）生产废水，确定最佳操作条件为：初始pH=3.8，H₂O₂浓度为9.99 g/L，H₂O₂/Fe²⁺摩尔比为20∶1，光照反应60 min。此条件下的废水COD去除率为89.1%，出水COD值在570 mg/L左右。经正交试验确定影响处理效果各因素的重要性顺序为：H₂O₂浓度＞H₂O₂/Fe²⁺摩尔比＞光照反应时间＞pH。UV的加入与单独的Fenton体系存在正相关的协同作用。废水降解的表观过程符合一级反应动力学模式。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.