Techno-economic evaluation of ultrasound and thermal pretreatments for enhanced anaerobic digestion of municipal waste activated sludge

To enhance the anaerobic digestion of municipal waste-activated sludge (WAS), ultrasound, thermal, and ultrasound + thermal (combined) pretreatments were conducted using three ultrasound specific energy inputs (1000, 5000, and 10,000 kJ/kg TSS) and three thermal pretreatment temperatures (50, 70 and 90 °C). Prior to anaerobic digestion, combined pretreatments significantly improved volatile suspended solid (VSS) reduction by 29-38%. The largest increase in methane production (30%) was observed after 30 min of 90 °C pretreatment followed by 10,000 kJ/kg TSS ultrasound pretreatment. Combined pretreatments improved the dimethyl sulfide (DMS) removal efficiency by 42-72% but did not show any further improvement in hydrogen sulfide (H₂S) removal when compared with ultrasound and thermal pretreatments alone. Economic analysis showed that combined pretreatments with 1000 kJ/kg TSS specific energy and differing thermal pretreatments (50-90 °C) can reduce operating costs by $44-66/ton dry solid when compared to conventional anaerobic digestion without pretreatments.     

Dry-thermophilic anaerobic digestion of organic fraction of municipal solid waste: methane production modeling

The influence of particle size and organic matter content of organic fraction of municipal solid waste (OFMSW) in the overall kinetics of dry (30% total solids) thermophilic (55 °C) anaerobic digestion have been studied in a semi-continuous stirred tank reactor (SSTR). Two types of wastes were used: synthetic OFMSW (average particle size of 1 mm; 0.71 g Volatile Solids/g waste), and OFMSW coming from a composting full scale plant (average particle size of 30 mm; 0.16 g Volatile Solids/g waste).A modification of a widely-validated product-generation kinetic model has been proposed. Results obtained from the modified-model parameterization at steady-state (that include new kinetic parameters as K, Y_pMAX and θ_MIN) indicate that the features of the feedstock strongly influence the kinetics of the process. The overall specific growth rate of microorganisms (μ_max) with synthetic OFMSW is 43% higher compared to OFMSW coming from a composting full scale plant: 0.238 d⁻¹ (K = 1.391 d⁻¹; Y_pMAX = 1.167 L CH₄/gDOC_c; θ_MIN = 7.924 days) vs. 0.135 d⁻¹ (K = 1.282 d⁻¹; Y_pMAX = 1.150 L CH₄/gDOC_c; θ_MIN = 9.997 days) respectively.Finally, it could be emphasized that the validation of proposed modified-model has been performed successfully by means of the simulation of non-steady state data for the different SRTs tested with each waste.     

Anaerobic co-digestion of municipal solid organic waste with melon residues to enhance biodegradability and biogas production

Management of solid organic waste has become a major challenge in developing countries. Raw solid organic waste can be converted into biogas through anaerobic digestion; however, the efficiency of the process is influenced by various factors including the composition of the substrate. The present study was designed with the objective of enhancing the biodegradability of the organic fraction of municipal solid waste (OFMSW) and biogas production through co-digestion of the substrate with melon residues. The study was conducted in batch mode in four phases. The results revealed that an addition of melon waste at the rate of 300?g?kg^?1 OFMSW substantially increased the biodegradation rate and biogas production compared to OFMSW alone. The removal of up to 57.2?% volatile solids and a carbon to nitrogen (C/N) ratio of 15.9 was achieved at a 60?% water level when the digestion mixture was treated with inocula collected from partially-degraded food waste. The findings of this study reveal that melon residues could be used as a potential co-substrate to enhance the biodegradability of OFMSW and biogas production.     

Impacts of microwave pretreatments on the semi-continuous anaerobic digestion of dairy waste activated sludge

Microwave (MW) irradiation is one of the new and possible methods used for pretreating the sludge. Following its use in different fields, this MW irradiation method has proved to be more appropriate in the field of environmental research. In this paper, we focused on the effects of MW irradiation at different intensities on solubilization, biodegradation and anaerobic digestion of sludge from the dairy sludge. The changes in the soluble fractions of the organic matter, the biogas yield, the methane content in the biogas were used as control parameters for evaluating the efficiency of the MW pretreatment. Additionally, the energetic efficiency was also examined. In terms of an energetic aspect, the most economical pretreatment of sludge was at 70% intensity for 12 min irradiation time. At this, COD solubilization, SS reduction and biogas production were found to be 18.6%, 14% and 35% higher than the control, respectively. Not only the increase in biogas production was investigated, excluding protein and carbohydrate hydrolysis was also performed successfully by this microwave pretreatment even at low irradiation energy input. Also, experiments were carried out in semi continuous anaerobic digesters, with 3.5 L working volume. Combining microwave pretreatment with anaerobic digestion led to 67%, 64% and 57% of SS reduction, VS reduction and biogas production higher than the control, respectively.     

Parameters affecting the stability of the digestate from a two-stage anaerobic process treating the organic fraction of municipal solid waste

This paper focused on the factors affecting the respiration rate of the digestate taken from a continuous anaerobic two-stage process treating the organic fraction of municipal solid waste (OFMSW). The process involved a hydrolytic reactor (HR) that produced a leachate fed to a submerged anaerobic membrane bioreactor (SAMBR). It was found that a volatile solids (VS) removal in the range 40-75% and an operating temperature in the HR between 21 and 35 °C resulted in digestates with similar respiration rates, with all digestates requiring 17 days of aeration before satisfying the British Standard Institution stability threshold of 16 mg CO₂ g VS⁻¹ day⁻¹. Sanitization of the digestate at 65 °C for 7 days allowed a mature digestate to be obtained. At 4 g VS L⁻¹ d⁻¹ and Solid Retention Times (SRT) greater than 70 days, all the digestates emitted CO₂ at a rate lower than 25 mg CO₂ g VS⁻¹ d⁻¹ after 3 days of aeration, while at SRT lower than 20 days all the digestates displayed a respiration rate greater than 25 mg CO₂ g VS⁻¹ d⁻¹. The compliance criteria for Class I digestate set by the European Commission (EC) and British Standard Institution (BSI) could not be met because of nickel and chromium contamination, which was probably due to attrition of the stainless steel stirrer in the HR.     

Aerobic thermophilic bacteria enhance biogas production

The enhancing effect of aerobic thermophilic (AT) bacteria on the production of biogas from anaerobically digested sewage sludge (methanogenic sludge) was investigated. Sewage sludge (5%, w/w) was incubated at 65°C with shaking for a few months to prepare the AT seed sludge. AT sludge was prepared by incubation of the AT seed sludge (5%, v/v) and sewage sludge (5%, w/w) at 65°C with shaking. The addition of this AT sludge (1.2% ± 0.5% of total volatile solids) to methanogenic sludge enhanced the production of biogas. The optimum volume of the addition and the pretreatment temperature of the AT sludge for optimum biogas production were 5% (v/v) and 65°C. Batch-fed anaerobic digestion was covered with the addition of various AT sludges. The AT sludge prepared with the AT seed sludge improved the biogas production by 2.2 times relative to that from the sewage sludge addition. The addition of sludge without AT seed sludge weakly enhanced biogas production. An aerobic thermophilic bacterium (strain AT1) was isolated from the AT seed sludge. Strain AT1 grew well in a synthetic medium. The production of biogas from the anaerobic digestion of sewage sludge was improved by the addition of 5% (v/v) AT1 bacterial culture compared with that from the sewage sludge addition. The addition of AT1 culture reduced the volatile solids by 21%, which was higher than the 12.6% achieved with the sewage sludge addition. The AT1 bacterial culture enhanced the biogas production more than the AT seed sludge. The phylogenetic analysis of the 16S rRNA gene revealed that strain AT1 is closely related to Geobacillus thermodenitrificans (100% sequence similarity). The improvement in the production of biogas with the AT sludge could be caused by thermophilic bacterial activity in the AT sludge.     

Treatment of municipal landfill leachate by catalytic wet air oxidation: Assessment of the role of operating parameters by factorial design

The wet air oxidation (WAO) of municipal landfill leachate catalyzed by cupric ions and promoted by hydrogen peroxide was investigated. The effect of operating conditions such as WAO treatment time (15-30 min), temperature (160-200 °C), Cu²⁺ concentration (250-750 mg L⁻¹) and H₂O₂ concentration (0-1500 mg L⁻¹) on chemical oxygen demand (COD) removal was investigated by factorial design considering a two-stage, sequential process comprising the heating-up of the reactor and the actual WAO. The leachate, at an initial COD of 4920 mg L⁻¹, was acidified to pH 3 leading to 31% COD decrease presumably due to the coagulation/precipitation of colloidal and other organic matter. During the 45 min long heating-up period of the WAO reactor under an inert atmosphere, COD removal values up to 35% (based on the initial COD value) were recorded as a result of the catalytic decomposition of H₂O₂ to reactive hydroxyl radicals. WAO at 2.5 MPa oxygen partial pressure advanced treatment further; for example, 22 min of oxidation at 200 °C, 250 mg L⁻¹ Cu²⁺ and 0-1500 mg L⁻¹ H₂O₂ resulted in an overall (i.e. including acidification and heating-up) COD reduction of 78%. Amongst the operating variables in question, temperature had the strongest influence on both the heating-up and WAO stages, while H₂O₂ concentration strongly affected the former and reaction time the latter. Nonetheless, the effects of temperature and H₂O₂ concentration were found to depend on the concentration levels of catalyst as suggested by the significance of their 3rd order interaction term.     

Anaerobic digestion of chicken feather with swine manure or slaughterhouse sludge for biogas production

Biogas production from anaerobic digestion of chicken feathers with swine manure or slaughterhouse sludge was assessed in two separate experiments. Ground feathers without any pre-treatment were added to 42-L digesters inoculated with swine manure or slaughterhouse sludge, representing 37% and 23% of total solids, respectively and incubated at 25 °C in batch mode. Compared to the control without feather addition, total CH₄ production increased by 130% (P < 0.001) and 110% (P = 0.09) in the swine manure and the slaughterhouse sludge digesters, respectively. Mixed liquor NH₄N concentration increased (P < 0.001) from 4.8 and 3.1 g/L at the beginning of the digestion to 6.9 and 3.5 g/L at the end of digestion in the swine manure and the slaughterhouse sludge digesters, respectively. The fraction of proteolytic microorganisms increased (P < 0.001) during the digestion from 12.5% to 14.5% and 11.3% to 13.0% in the swine manure and the slaughterhouse sludge digesters with feather addition, respectively, but decreased in the controls. These results are reflective of feather digestion. Feather addition did not affect CH₄ yields of the swine manure digesters (P = 0.082) and the slaughterhouse sludge digesters (P = 0.21), indicating that feathers can be digested together with swine manure or slaughterhouse sludge without negatively affecting the digestion of swine manure and slaughterhouse sludge.     

Short term effects of copper, sulfadiazine and difloxacin on the anaerobic digestion of pig manure at low organic loading rates

Antibiotics of inorganic and organic origin in pig manure can inhibit the anaerobic process in biogas plants. The influence of three frequently used antibiotics, copper dosed as CuSO₄, sulfadiazine (SDZ), and difloxacin (DIF), on the anaerobic digestion process of pig manure was studied in semi-continuous experiments. Biogas production recovered after every Cu dosage up to a sum of 12.94 g Cu kg⁻¹ organic dry matter (ODM), probably due to Cu precipitation following the formation of sulphide from sulphate. Complete inhibition was found at the very high Cu concentration of 19.40 g Cu kg⁻¹ ODM. Inhibitory effect of SDZ and DIF was observed at concentrations as high as 2.70 g kg⁻¹ ODM and 0.54 g kg⁻¹ ODM, respectively. It seems very unlikely that the antibiotics tested would inhibit the anaerobic process in a full-scale biogas plant.     

The impact of pretreatment and inoculum to substrate ratio on methane potential of organic wastes from various origins

Biochemical methane potentials (BMP) of two different substrates from macroalgae (MA) and market place wastes (MPW) were investigated using anaerobic granulated sludge from food industry with different ratios of substrate to inoculum (S/X). The substrates were used as MA only, MPW only, MA–MPW mixture, pretreated MA, and pretreated MA–MPW mixture. Research involved investigation of the effects of parameters such as temperature (35, 45, and 55 °C), substrate to inoculum ratio (S/X = 0.5, 2.0, 4.0, and 6.0 as g VS_substrate/g VS_inoculum), and the type of pretreatment (by microwave, thermal, and ultrasonic) on BMP. BMP assays were performed for all substrates. The highest cumulative biogas production (and BMP) were obtained for MA only at an S/X ratio of 4.0 g VS/g VS as 357 L_biogas/kg VS (197 L CH₄/kg VS) and 33 L_biogas/kg VS (17 L CH₄/kg VS), respectively, at 35 and 55 °C. For pretreated substrates, the highest cumulative biogas production and BMP were observed as 287 L_biogas/kg VS and 146 L CH₄/kg VS using pretreated macroalgae at 35 °C. Results suggested that MA only and MA–MPW mixtures are suitable substrates for biogas production. It is also concluded that any type of pretreatment has adverse effects on biogas and methane productions.     

Semi-continuous anaerobic co-digestion of thickened waste activated sludge and fat, oil and grease

Co-digestion of thickened waste activated sludge (TWAS) and fat, oil and grease (FOG) was conducted semi-continuously under mesophilic conditions. The results showed that daily methane yield at the steady state was 598 L/kg VS_added when TWAS and FOG (64% of total VS) were co-digested, which was 137% higher than that obtained from digestion of TWAS alone. The biogas composition was stabilized at a CH₄ and CO₂ content of 66.8% and 29.5%, respectively. Micronutrients added to co-digestion did not improve the biogas production and digestion stabilization. With a higher addition of FOG (74% of total VS), the digester initially failed but was slowly self-recovered; however, the methane yield was only about 50% of a healthy reactor with the same organic loading rate.     

Reducing the environmental impact of methane emissions from dairy farms by anaerobic digestion of cattle waste

Four dairy cattle farms considered representative of Northern Spain milk production were studied. Cattle waste was characterised and energy consumption in the farms was inventoried. Methane emissions due to slurry/manure management and fuel consumption on the farms were calculated. The possibility of applying anaerobic digestion to the slurry to minimise emissions and of using the biogas produced to replace fossil fuels on the farm was considered. Methane emissions due to slurry management (storage and use as fertiliser) ranged from 34 to 66 kg CH₄ cow⁻¹ year⁻¹ for dairy cows and from 13 to 25 kg CH₄ cow⁻¹ year⁻¹ for suckler calves. Cattle on these farms are housed for most of the year, and the contribution from emissions from manure dropped in pastures is insignificant due to the very low methane conversion factors. If anaerobic digestion were implemented on the farms, the potential GHG emissions savings per livestock unit would range from 978 to 1776 kg CO₂ eq year⁻¹, with the main savings due to avoided methane emissions during slurry management. The methane produced would be sufficient to supply digester heating needs (35-55% of the total methane produced) and on-farm fuel energy requirements.     

Anaerobic digestion and co-digestion of slaughterhouse waste (SHW): Influence of heat and pressure pre-treatment in biogas yield

Mesophilic anaerobic digestion (34 ± 1 °C) of pre-treated (for 20 min at 133 °C, >3 bar) slaughterhouse waste and its co-digestion with the organic fraction of municipal solid waste (OFMSW) have been assessed. Semi-continuously-fed digesters worked with a hydraulic retention time (HRT) of 36 d and organic loading rates (OLR) of 1.2 and 2.6 kg VS_feed/m³ d for digestion and co-digestion, respectively, with a previous acclimatization period in all cases. It was not possible to carry out an efficient treatment of hygienized waste, even less so when OFMSW was added as co-substrate. These digesters presented volatile fatty acids (VFA), long chain fatty acids (LCFA) and fats accumulation, leading to instability and inhibition of the degradation process. The aim of applying a heat and pressure pre-treatment to promote splitting of complex lipids and nitrogen-rich waste into simpler and more biodegradable constituents and to enhance biogas production was not successful. These results indicate that the temperature and the high pressure of the pre-treatment applied favoured the formation of compounds that are refractory to anaerobic digestion.The pre-treated slaughterhouse wastes and the final products of these systems were analyzed by FTIR and TGA. These tools verified the existence of complex nitrogen-containing polymers in the final effluents, confirming the formation of refractory compounds during pre-treatment.     

Effect of alkaline pretreatment on anaerobic digestion of solid wastes

The introduction of the anaerobic digestion for the treatment of the organic fraction of municipal solid waste (OFMSW) is currently of special interest. The main difficulty in the treatment of this waste fraction is its biotransformation, due to the complexity of organic material. Therefore, the first step must be its physical, chemical and biological pretreatment for breaking complex molecules into simple monomers, to increase solubilization of organic material and improve the efficiency of the anaerobic treatment in the second step. This paper describes chemical pretreatment based on lime addition (Ca(OH)2), in order to enhance chemical oxygen demand (COD) solubilization, followed by anaerobic digestion of the OFMSW. Laboratory-scale experiments were carried out in completely mixed reactors, 1 L capacity. Optimal conditions for COD solubilization in the first step of pretreatment were 62.0 mEq Ca(OH)2/L for 6.0 h. Under these conditions, 11.5% of the COD was solubilized. The anaerobic digestion efficiency of the OFMSW, with and without pretreatment, was evaluated. The highest methane yield under anaerobic digestion of the pretreated waste was 0.15 m3CH4/kg volatile solids (VS), 172.0% of the control. Under that condition the soluble COD and VS removal were 93.0% and 94.0%, respectively. The results have shown that chemical pretreatment with lime, followed by anaerobic digestion, provides the best results for stabilizing the OFMSW.     

Gasification of the char derived from distillation of granulated scrap tyres

This work reports the effect of pressure on the steam/oxygen gasification at 1000 °C of the char derived from low temperature-pressure distillation of granulated scrap tyres (GST). The study was based on the analysis of gas production, carbon conversion, cold gas efficiency and the high heating value (HHV) of the product. For comparison, similar analyses were carried out for the gasification of coals with different rank.In spite of the relatively high ash (≈12 wt.%) and sulphur (≈3 wt.%) contents, the char produced in GST distillation can be regarded as a reasonable solid fuel with a calorific value of 34 MJ kg⁻¹. The combustion properties of the char (E_A ≈ 50 kJ mol⁻¹), its temperature of self-heating (≈264 °C), ignition temperature (≈459 °C) and burn-out temperature (≈676 °C) were found to be similar to those of a semi-anthracite.It is observed that the yield, H₂ and CO contents and HHV of the syngas produced from char gasification increase with pressure. At 0.1 MPa, 4.6 Nm³ kg_char⁻¹ of syngas was produced, containing 28% v/v of H₂ and CO and with a HHV around 3.7 MJ Nm⁻³. At 1.5 MPa, the syngas yield achieved 4.9 Nm³ kg_char⁻¹ with 30% v/v of H₂-CO and HHV of 4.1 MJ Nm⁻³. Carbon conversion significantly increased from 87% at 0.1 MPa to 98% at 1.5 MPa.It is shown that the char derived from distillation of granulated scrap tyres can be further gasified to render a gas of considerable heating value, especially when gasification proceeds at high pressure.     

Biogas from the organic fraction of municipal solid waste: Dealing with contaminants for a solid oxide fuel cell energy generator

The present work investigates electricity production using a high efficiency electrochemical generator that employs as fuel a biogas from the dry anaerobic digestion of the organic fraction of municipal solid waste (OFMSW).The as-produced biogas contains several contaminants (sulfur, halogen, organic silicon and aromatic compounds) that can be harmful for the fuel cell: these were monitored via an innovative mass spectrometry technique that enables for in-line and real-time quantification.A cleaning trap with activated carbons for the removal of sulfur and other VOCs contained in the biogas was also tested and monitored by observing the different breakthrough times of studied contaminants.The electrochemical generator was a commercial Ni anode-supported planar Solid Oxide Fuel Cell (SOFC), tested for more than 300 h with a simulated biogas mixture (CH₄ 60 vol.%, CO₂ 40 vol.%), directly fed to the anode electrode. Air was added to promote the direct internal conversion of CH₄ to H₂ and CO via partial oxidation (POx).The initial breakthrough of H₂S from the cleaning section was also simulated and tested by adding ～1 ppm(v) of sulfur in the anode feed; a full recovery of the fuel cell performance after 24 h of sulfur exposure (～1 ppm(v)) was observed upon its removal, indicating the reliable time of anode exposure to sulfur in case of exhausted guard bed.     

Efficiency of the anaerobic treatment of the organic fraction of municipal solid waste: collection and pretreatment.

This report is based on several years of co-operation between our research groups and Danish biogas plants. Throughout the years, there has been a fruitful exchange of know-how and experiences in laboratory scale on the one hand and large scale on the other, leading to a better understanding of the principles of the anaerobic digestion process and to an optimization of its large-scale implementation. In order to get an overview of the current situation concerning the treatment of the organic fraction of municipal solid waste (OFMSW) in Denmark, interviews were carried out with operators of the biogas plants where OFMSW is treated and the municipality staff responsible for waste management. With the aim of fulfilling the governmental goal to treat 150,000 tons of OFMSW by the year 2004 mainly by anaerobic digestion, the different municipalities are investigating different concepts of waste collection and treatment. The quality of the OFMSW treated is the key to smooth operation of the biogas process including a high biogas yield and production of an effluent that is feasible for use as fertilizer on agricultural land. Comparison of the different concepts leads to the conclusion that source-sorting of OFMSW in paper bags is preferable to collection in plastic bags and successive separation of plastics in a waste processing treatment plant.     

Evaluation of respiration in compost landfill biocovers intended for methane oxidation

A low-cost alternative approach to reduce landfill gas (LFG) emissions is to integrate compost into the landfill cover design in order to establish a biocover that is optimized for biological oxidation of methane (CH₄). A laboratory and field investigation was performed to quantify respiration in an experimental compost biocover in terms of oxygen (O₂) consumption and carbon dioxide (CO₂) production and emission rates. O₂ consumption and CO₂ production rates were measured in batch and column experiments containing compost sampled from a landfill biowindow at Fakse landfill in Denmark. Column gas concentration profiles were compared to field measurements. Column studies simulating compost respiration in the biowindow showed average CO₂ production and O₂ consumption rates of 107 ± 14 g m⁻² d⁻¹ and 63 ± 12 g m⁻² d⁻¹, respectively. Gas profiles from the columns showed elevated CO₂ concentrations throughout the compost layer, and CO₂ concentrations exceeded 20% at a depth of 40 cm below the surface of the biowindow. Overall, the results showed that respiration of compost material placed in biowindows might generate significant CO₂ emissions. In landfill compost covers, methanotrophs carrying out CH₄ oxidation will compete for O₂ with other aerobic microorganisms. If the compost is not mature, a significant portion of the O₂ diffusing into the compost layer will be consumed by non-methanotrophs, thereby limiting CH₄ oxidation. The results of this study however also suggest that the consumption of O₂ in the compost due to aerobic respiration might increase over time as a result of the accumulation of biomass in the compost after prolonged exposure to CH₄.     

Ultrasound assisted biogas production from landfill leachate

The aim of this study is to increase biogas production and methane yield from landfill leachate in anaerobic batch reactors by using low frequency ultrasound as a pretreatment step. In the first part of the study, optimum conditions for solubilization of organic matter in leachate samples were investigated using various sonication durations at an ultrasound frequency of 20 kHz. The level of organic matter solubilization during ultrasonic pretreatment experiments was determined by calculating the ratio of soluble chemical oxygen demand (sCOD) to total chemical oxygen demand (tCOD). The sCOD/tCOD ratio was increased from 47% in raw leachate to 63% after 45 min sonication at 600 W/l. Non-parametric Friedman’s test indicated that ultrasonic pretreatment has a significant effect on sCOD parameter for leachate (p < 0.05). In the second part of the study, anaerobic batch reactors were operated for both ultrasonically pretreated and untreated landfill leachate samples in order to assess the effect of sonication on biogas and methane production rate. In anaerobic batch reactor feed with ultrasonically pretreated leachate, 40% more biogas was obtained compared to the control reactor. For statistical analysis, Mann–Whitney U test was performed to compare biogas and methane production rates for raw and pretreated leachate samples and it has been found that ultrasonic pretreatment significantly enhanced biogas and methane production rates from leachate (p < 0.05) in anaerobic batch reactors. The overall results showed that low frequency ultrasound pretreatment can be potentially used for wastewater management especially with integration of anaerobic processes.     

Hydrometallurgical treatment of used printed circuit boards after thermal treatment

The hydrometallurgical route of copper and tin extraction from printed circuit boards (PCB) of used personal computers after thermal pretreatment is discussed. The PCB fractions crushed and sorted into −8 + 0, −8 + 3 and −3 + 0 mm were used for the experiments. The samples were thermally pretreated at temperatures of 300, 500, 700 and 900 °C during 15, 30 and 60 min with the presence of air (burning) before the leaching process.The leaching solution of 1 M HCl and temperature of 80 °C was used for the leaching. The original as well as thermally pretreated samples were leached under these conditions.The weight losses within the range from 5% to 35% were achieved by burning depending on the burning temperature. The increase of burning temperature causes the copper extraction into solution up to 98%, while copper extraction into solution from non-burned samples was up to 6%. The opposite effect was observed in the case of the tin leaching, where the highest extraction was achieved when the original sample was leached. The increase of the burning temperature caused the lowering of the copper extraction.