燃煤锅炉湿法脱硫烟气中颗粒物排放特征

选择北京市典型燃煤锅炉进行研究,结果表明:烟气中可凝结颗粒物在总颗粒物中占有较高比例,供热燃煤锅炉总颗粒物排放水平明显高于电厂燃煤锅炉;颗粒物中水溶性离子含量较高,供热燃煤锅炉硫酸根比例尤其显著;烟气总颗粒物中存在大量不稳定的易被氧化的组分;同为燃煤源,不同的烟气净化工艺排放的PM2.5组分特征差异明显;现有标准和技术规范存在不足,无法满足全面、准确监测污染源排放总颗粒物的实际需要。建议建立总颗粒物、可凝结颗粒物的监测技术规范,全面测算燃煤锅炉硫、氮化合物排放情况,科学评估脱硫及脱硝效率。     

超低排放下燃煤电厂颗粒物排放特征分析研究

选取6家经过超低排放改造的燃煤电厂,对湿法脱硫(WFGD)和湿式电除尘器(WESP)进出口烟气中TPM、PM_(10)、PM_(2.5)、PM_1进行测试,分析研究超低排放下燃煤电厂颗粒物的排放特征及电除尘器后净化设备对颗粒物的脱除效果。结果表明,6家电厂TPM、PM_(10)、PM_(2.5)、PM_1排放浓度分别为0.75~2.36、0.71~2.12、0.65~1.96、0.51~1.57 mg/m~3。分析烟气中颗粒物粒径分布可知,除尘器后,PM10占TPM质量比低于40%,且比例随烟气经过WFGD和WESP而逐渐降低。WFGD对PM2.5有较好的脱除效果,而WESP对PM1脱除效果显著。为满足超低排放标准,6家电厂除尘器后脱除设备综合除尘效率大多在85%以上。计算得到6家电厂TPM、PM_(10)、PM_(2.5)、PM_1排放因子,与超低排放改造之前同等级燃煤电厂相比,6家电厂不同粒径颗粒物排放因子均显著降低,也远低于西方发达国家燃煤电厂颗粒物排放因子。     

典型超低排放烟气中颗粒物组分特征研究

为了解超低排放改造后工业源烟气颗粒物排放状况及其组分特征,于2020年1—5月对2家垃圾焚烧企业和2家燃煤电厂外排烟气开展了调查,同步采集外排烟气中的可过滤颗粒物（FPM）和可凝结颗粒物（CPM）,测定质量浓度及其离子组分、元素组分,对各组分浓度范围及平均值进行统计评价。结果表明：4家企业外排烟气中CPM和FPM质量浓度平均值的比值分别为30.5,10.3,3.0,0.94,CPM的排放不可忽视;离子分析结果发现,烟气处理过程中产生的铵离子和硫酸根离子等水溶性离子,在FPM中基本未检出,在CPM中检出且浓度较高;金属元素分析结果发现,检出的铬（Cr）、镍（Ni）、铅（Pb）3种元素主要存在于FPM中,而砷（As）、汞（Hg）元素则更多地存在于CPM中;CPM中水溶性离子为主要成分,以水溶性离子作为CPM排放的控制因子是可行的。     

固定污染源排放可凝结颗粒物采样方法综述

综述了国内外固定污染源可凝结颗粒物(CPM)冲击冷凝法和稀释冷凝法2种采样方法,指出CPM是固定污染源排放颗粒物的重要组成部分,国内对于固定污染源CPM排放的监测和研究尚处于起步阶段,缺乏必要的CPM采样标准方法。通过分析2种采样方法的优缺点,提出冲击冷凝采样法需进一步降低SO_2等水溶性气体的影响,提高气相CPM冷凝效果及超细颗粒态CPM的捕集效率;稀释冷凝法需提高采样装置的便携性实现可过滤颗粒物(FPM)和CPM的分离采样,提高采样管路壁面颗粒物回收率。同时,针对我国固定污染源如燃煤电厂大量使用湿法脱硫设备的情况,CPM采样方法需提高对低温高湿且夹带液滴烟气采样的适用性。     

燃煤电厂烟气颗粒物分级测定与分析

采用分级撞击采样器(DPI)对燃煤电厂烟气颗粒物测定并分析,试验表明,PM10、PM2.5及PM1在湿除出口/烟囱入口的质量浓度分别为0.26 mg/m3~1.47 mg/m3、0.22 mg/m3~1.29 mg/m3、0.17 mg/m3~1.00 mg/m3。分析可知,除尘器后烟气颗粒物PM10中主要是PM2.5,而PM2.5~10占比低于35%;烟气经湿法脱硫后,PM2.5~10的比例进一步大幅降低,经湿式除尘器后,PM2.5~10的占比变化很小,而PM1~2.5的占比大幅降低。监测结果表明,湿式除尘器对烟气颗粒物的脱除效果优于湿法脱硫,而随着颗粒物粒径的减小,2种脱除设备的脱除效率均出现降低。     

基于实测的湿法脱硫系统对颗粒物去除效果的研究

通过对我国4座燃煤电厂5台不同容量机组的石灰石-石膏湿法脱硫(WFGD)系统进、出口烟气中颗粒物的实测,计算各电厂湿法脱硫系统对颗粒物的去除效果,并分析其排放特征。结果表明:WFGD系统对烟气中总颗粒物的去除效率介于46.00%~61.70%之间,有较好的去除效果;对PM1的去除效率介于-12.61%~-1.58%之间,对PM2.5的去除效率介于-2.02%~8.50%之间,对PM10的去除效率介于42.63%~58.68%之间,对PM2.5及更小的亚微米颗粒的去除作用非常有限且波动较大,工况不佳易出现逆增长现象。     

固定污染源烟气中可凝结颗粒物监测技术现状及展望

随着国家对大气环境治理的推进,可凝结颗粒物(CPM)成为工业烟气防治的关键污染物。CPM在烟道高温环境中为气态物质,排入大气环境后快速凝结成颗粒态物质,对其进行准确测量是国内外的前沿技术挑战之一。通过研究分析CPM在烟气和烟羽中演化特征与监测技术现状,阐明CPM的概念、形成机制与排放特征,阐释已有的工业烟气CPM采集与分析方法及其存在的问题,并进一步对超低排放烟气中CPM的在线监测和质控技术提出展望。     

燃用蔗髓锅炉的硫平衡及二氧化硫排放分析

通过现场监测和调研数据,分析燃用蔗髓锅炉的硫平衡及SO 2排放情况。结果显示,烟气排放的SO 2主要来源于鲜蔗和回用洗布水中含有的硫。8个锅炉硫排放在线监测均值与手工监测均值相对偏差为3.76%~14.9%,表明结果一致性较好。蔗髓硫质量分数为0.01%~0.04%,蔗髓含硫折算后的SO 2值和在线监测SO 2值分别为22.1 mg/m 3~49.9 mg/m 3和43.9 mg/m 3~114.5 mg/m 3,说明鲜蔗和制糖工艺流程的共同影响使得燃用蔗髓锅炉排放烟气SO 2值偏高。     

湿法脱硫烟气中多形态颗粒物的测量方法及组分特征

为全面测量固定源湿法脱硫烟气中多形态颗粒物的排放浓度及其离子组成特征，提出了一种基于一级冷凝、二级过滤和一级冲击吸收的多形态烟气颗粒物的同步测量方法，外场实测了3种湿法脱硫和除尘工艺的排放水平。现场测试表明：简易湿法除尘脱硫（NaOH法）一体化装置烟气中可过滤颗粒物（FPM）浓度为（36±11）mg/m³，可逃逸颗粒物（EPM）浓度为（33±7）mg/m³；氧化镁法+布袋除尘工艺烟气中FPM浓度为（14±5）mg/m³，EPM浓度为（13±6）mg/m³；石灰石-石膏脱硫+电袋除尘工艺烟气中FPM浓度低，小于3 mg/m³，EPM浓度为（6±1）mg/m³；烟气中EPM是传统滤膜法检测FPM浓度的0.7~5.7倍，EPM的主要存在形态为冷凝液中的可溶解颗粒物（DPM），颗粒物的组分与脱硫方法密切相关，各形态颗粒物的主要组分是SO₄^2-、SO₃^2-、NO₃^-、NO₂^-、NH₄⁺、Cl^-、Na⁺、Mg²⁺和Ca²⁺等离子。     

2019—2021年徐州市大气细颗粒物化学组成特征及来源解析

徐州市地处四省交界,大气污染物来源复杂,颗粒物污染在气象条件不利时较为显著。通过地面观测数据、颗粒物组分连续观测、源解析及轨迹溯源等方法,对徐州市2019—2021年颗粒物变化特征进行了全面分析,以定量解析各类污染源的贡献,识别对颗粒物贡献显著的化学成分。结果表明：PM_2.5各组分质量占比中二次无机盐和有机碳相对较高,其中二次无机盐SNA(SO■、NO^-₃、NH⁺₄)占比达到59.1%～62.7%;水溶性离子总浓度逐年降低,但Mg²⁺和Ca²⁺浓度2021年分别同比增加2%和12.5%,说明扬尘污染存在反弹。秋冬季水溶性离子明显较高,Cl^-浓度明显高于其他季节,表明徐州市秋冬季受移动源、燃煤源和二次有机气溶胶共同影响。PM_2.5中OC与EC质量浓度比为4.88～8.40,说明徐州市颗粒物受多源影响,柴油、汽油机动车尾气排放以及燃煤排放对颗粒物贡献较大。后向轨迹分析表明,污染严重的1月污染物主...     

A New Mathematical Approach in Environmental and Life Sciences: Gene–Environment Networks and Their Dynamics

An important research area in life sciences is devoted to modeling, prediction, and dynamics of gene-expression patterns. As clearly understood in these days, this enterprise cannot become satisfactory without acknowledging the role of the environment. To a representation of past, present, and most likely future states, we also encounter measurement errors and uncertainties. This paper surveys and improves recent advances in understanding the foundations and interdisciplinary implications of the newly introduced gene–environment networks, and it integrates the important theme of carbon dioxide emission reduction into the networks and dynamics. We also introduce some operational and managerial issues of practical working and decision making, expressed in terms of sliding windows, quadrants (modules) of parametric effects, and navigating (controlling) between such effects and directing them. Given data from DNA microarray experiments and environmental records, we extract nonlinear ordinary differential equations that contain parameters that have to be determined. For this, we employ modern (Chebychevian) approximation and (generalized semi-infinite) optimization. After this is provided, time- discretized dynamical systems are studied. A combinatorial algorithm with polyhedra sequences allows to detect the region of parametric stability. Finally, we analyze the topological landscape of gene–environment networks with its structural (in)stability. By embedding as a module and investigating CO₂ emission control and figuring out game theoretical aspects, we conclude. This pioneering work is theoretically elaborated, practically devoted to health care, medicine, education, living conditions, and environmental protection, and it invites the readers to future research.      

微波消解-原子吸收光度法测定土壤中铜锌铅镉镍铬

用微波消解－原子吸收光度法测定土壤中铜，锌，铅，镉，镍和铬。通过硝酸－氢氟酸－过氧化氢体系消解液对土壤样品消解，选择出微波最佳消解条件。对硝酸－盐酸－过氧化氢体系消解液和硝酸－氢氟酸－过氧化氢体系消解液进行消解对比试验，发现前者不能将土壤样品完全消解，后者能将样品消解完全，但需将消解液中剩余的酸赶尽，否则测定结果将明显偏低。微波消解土壤与传统电热消解相比，操作简便快速，可提高工作效率。     

Topsoil and Housedust Metal Concentrations in the Vicinity of a Lead Battery Manufacturing Plant

The aim of the study was to determine the extent of heavy metal pollution in the vicinity of a lead battery manufacturing plant in the Czech Republic, both in the general environment and within homes. Topsoils (0–5 cm) were sampled from 100 sites along 4 transects which crossed the battery factory, the town centre and outlying rural areas. Housedust samples were collected from 15 plant-workers' homes and 15 non plant-workers' homes located at various distances from the factory. Samples were analysed for levels of Pb, Zn, Cd, Cu, As and Sb, using ICP-AES. Soil concentrations of Pb, Cd, As and Sb peaked at the perimeter fence of the battery factory with Pb levels of up to 12 650 g g> ^-1. Concentrations of these metals decreased exponentially within 500 m of the plant. Whilst the battery factory does appear to be a source of all the metals with the exception of Zn, emissions do not appear to be transported to any great extent over distances of more than 0.5 km. Topsoil and housedust concentrations of Pb, Zn, Cd, Cu, As and Sb in the general Mlada Boleslav area do not appear to be significantly different from those recorded in a large scale survey of urban soils in the United Kingdom. A comparison of housedust Pb concentrations in homes of plant workers and non-plant workers suggests that there may be a small input of Pb into the home environment by battery plant employees.     

An Overview of Contaminant-Related Issues Identified by Monitoring in San Francisco Bay

The San Francisco Estuary Regional Monitoring Program for Trace Substances (RMP) began in 1993 and is sponsored by 74 local, state, and federal agencies and companies through their discharge or Bay use permits. The RMP monitors water, sediment, toxicity, and bivalve bioaccumulation at 25 sites in the Bay that are considered to represent "background" conditions. Several major environmental issues have been identified by the RMP. Polychlorinated biphenyls and mercury were often above water quality guidelines, and often occurred in fish tissues above U.S. Environmental Protection Agency (U.S. EPA) screening values. Concentrations do not appear to be decreasing, suggesting continuing inputs. Episodes of aquatic toxicity often occurred following runoff events that transport contaminants into the Bay from urbanized and agricultural portions of the watershed. Sediment toxicity occurred throughout the Bay, and has been correlated with concentrations of specific contaminants (chlordanes, polynuclear aromatic hydrocarbons) at some locations; mixtures of contaminants were probably also important. Since the RMP does not monitor all ecosystem components, assessments of the overall condition of the Bay cannot be made. However, in terms of contamination, the RMP samples suggest that the South Bay, and North Bay sites are moderately contaminated.     

Biomagnification factors (fish to Osprey eggs from Willamette River,Oregon, U.S.A.) for PCDDs,PCDFs, PCBs and OC pesticides

A migratory population of 78 pairs of Osprey (Pandion haliaetus) nesting along the Willamette River in westernOregon was studied in 1993. The study was designed to determinecontaminant concentrations in eggs, contaminant concentrationsin fish species predominant in the Ospreys diet, andBiomagnification Factors (BMFs) of contaminants from fish specieseaten to Osprey eggs. Ten Osprey eggs and 25 composite samplesof fish (3 species) were used to evaluate organochlorine (OC)pesticides, polychlorinated biphenyls (PCBs), polychlorinateddibenzo-p-dioxins (PCDDs), and polychlorinated dibenzofurans(PCDFs). Mercury was also analyzed in fish. Geometric meanresidues in Osprey eggs were judged low, e.g., DDE 2.3 g g^-1 wet weight (ww), PCBs 0.69 g g^-1, 2,3,7,8-TCDD 2.3 ng kg^-1, and generally well below known threshold values for adverse effects on productivity, and the population was increasing. Osprey egg residue data presentedby River Mile (RM) are discussed, e.g., higher PCDDs were generally found immediately downstream of paper mills and eggsfrom the Willamette River had significantly elevated PCBs and PCDDs compared to reference eggs collected nearby in the CascadeMountains. Prey remains at nest sites indicated that the Largescale Sucker (Catostomus macrocheilus) and NorthernPikeminnow (Ptychocheilus oregonensis) accounted for an estimated 90.1% of the biomass in the Osprey diet, and composite samples of these two species were collected from different sampling sites throughout the study area for contaminant analyses. With the large percentage of the fishbiomass in the Osprey diet sampled for contaminants (and fisheaten by Ospreys similar in size to those chemically analyzed),and fish contaminant concentrations weighted by biomass intake, a mean BMF was estimated from fish to Osprey eggs for the largeseries of contaminants. BMFs ranged from no biomagnification(0.42) for 2,3,7,8-TCDF to 174 for OCDD. Our findings for themigratory Osprey were compared to BMFs for the resident HerringGull (Larus argentatus), and differences are discussed. Webelieve a BMF approach provides some basic understanding ofrelationships between contaminant burdens in prey species offish-eating birds and contaminants incorporated into their eggs,and may prove useful in understanding sources of contaminants inmigratory species although additional studies are needed.     

Cyanobacterial Flora from Polluted Marine Shores

Citation of cyanobacterial cultures from the shores of south west coast of Gujarat, India and their relationship with sea water quality, influenced by extensive pollutant runoff is reported in this study. Intensity of pollution was evaluated by physico-chemical analysis of water. Higher load of suspended solids (60–1000 mg l⁻¹) and nutrients (PO₄ ⁻P: 1.3–4 μmole l⁻¹ and NO₃ ⁻N: 12.5–17.8 μmole l⁻¹) were persistent throughout the analysis. Community structure is seen to be influenced by such persistent pollution. Twenty nine cyanobacterial species were isolated belonging to 9 genera of 4 families, with an elevated occurrence of Oscillatoria and Lyngbya species. No heterocystous cyanobacteria were isolated throughout the study.     

An investigation on biological stability of product water generated by lab-scale and pilot-scale distillation systems

Material Disposal Area G is the primary low-levelradioactive waste disposal site at Los Alamos NationalLaboratory, New Mexico, and is adjacent to Pueblo of SanIldefonso lands. Pueblo residents and Los Alamos scientists areconcerned about radiological doses resulting from uptake of AreaG radionuclides by mule deer (Odocoileus hemionus) andRocky Mountain elk (Cervus elaphus), then consumption ofdeer and elk meat by humans. Tissue samples were collected fromdeer and elk accidentally killed near Area G and were analyzedfor ³H, ⁹⁰Sr, total U, ²³⁸Pu, ^{239, 240}Pu,²⁴¹Am, and ¹³⁷Cs. These data were used to estimatehuman doses based on meat consumption of 23 kg y^-1. Humandoses were also modeled using RESRAD, and dose rates to deer andelk were estimated with a screening model. Dose estimates tohumans from tissue consumption were 2.9 × 10^-3 mSv y^-1and 1.6 × 10^-3 mSv y^-1 from deer and elk, respectively,and RESRAD dose estimates were of the same order of magnitude. Estimated dose rates to deer and elk were 2.1 × 10^-4 mGyd^-1 and 4.7 × 10^-4 mGy d^-1, respectively. Allestimated doses were significantly less than established exposurelimits or guidelines.     

The Draft of the New German Guideline VDI 3782/8 to Model Automobile Exhaust Dispersion

The draft of the German guideline to calculate automobile exhaust dispersion is explained. It contains a two-stage-system: For first quick estimates the guideline contains the simple models MLuS and STREET. In case these models are not applicable or their results shows concentration levels close to the air quality standards, the more complex models PROKAS_V and MISKAM are recommended. PROKAS_V is a Gaussian plume model, MISKAM is a 3-dimensional microscale non hydrostatic flow model for built-up areas with an Eulerian dispersion model. The guideline comprises cases in rural areas without or with few adjacent buildings as well as urban areas with buildings near the roads. The contribution gives information about the models, typical results and some of the problems showing up presently.     

Hydrocarbon Utilization in Yeast Isolates Found to Grow in Association with Petroleum in a Polluted Ultisol of Midwestern Nigeria

The population counts of hydrocarbon-utilising yeasts weremonitored at six sampling stations in the Benin City municipalarea over a four-week period. Although the population countswere relatively constant in each locality, the highest countsoccurred in areas heavily polluted by domestic and industrialeffluents. A total of thirty-five hydrocarbon-degrading yeastswere isolated from soil at the sampling stations usingn-hexadecane as sole carbon source. The isolates were identifiedas belonging to the genera Candida (27 strains), Endomycopsis (4 strains). All the organisms grew on long-chainn-alkane, kerosene, diesel oil and crude oil but failed to growon short-chain n-alkane, aromatic and alicyclic hydrocarbons.Measurement of growth attributes of the isolates usingn-hexadecane, diesel oil and crude oil as substrates showed thatthe Candida species were better utilizers of hydrocarbonsubstrates relative to Endomycopsis and Schizosaccharomyces species.     

Hydrologic–Economic Model for Managing Irrigation Intensity in Irrigation Areas under Watertable and Soil Salinity Targets

This paper gives mathematical details and sample applications of SWAGMAN Farm (SWAGMAN, Salt Water and Groundwater Management), a farm-scale hydrologic economic model that integrates agronomic, climatic, irrigation, hydrogeological and economic aspects of irrigated agriculture. The model is capable of determining optimum mix of land use to keep watertable and soil salinity within acceptable limits while maximising the economic returns. Alternatively, the model can simulate water and salt balance and economics of a given cropping preference. Web-based and Geographic Information Systems versions of the model are available for integration with the environmental reporting systems of the irrigation areas.