An Automated Wet Deposition System to Compare the Effects of Reduced and Oxidised N on Ombrotrophic Bog Species: Practical Considerations

Critical N loads for ombrotrophic bogs, which often contain rare and N-sensitive plants (especially those in lower plant groups: lichens, mosses and liverworts), are based on very few experimental data from measured, low background N deposition areas. Additionally the relative effects of reduced versus oxidised N are largely unknown. This paper describes an automated field exposure system (30 km S. of Edinburgh, Scotland) for treating ombrotrophic bog vegetation with fine droplets of oxidised N (NaNO₃) and reduced N (NH₄Cl). Whim Moss exists in an area of low ambient N deposition (ca. 8 kg N ha^–1 y^–1), the sources and quantification of which are described. The wet N treatment system is run continuously, and is controlled/activated by wind speed and rainfall to provide a unique simulation of real world treatment patterns (no rain=no treatment). Simulated precipitation is supplied at ionic concentrations below4mMin rainwater collected on site. Treatments provide a replicated dose response to 16, 32 and 64 kg N ha^–1 y^–1 adjusted for ambient deposition (8 kg N ha^–1 y^–1). The 16 and 64 kg N ha^–1 y^–1 are duplicated with a P+K supplement. Baseline soil chemistry and foliar nutrient status was established for all 44 plots for Calluna vulgaris, Sphagnum capillifolium, Hypnum jutlandicum and Cladonia portentosa.     

Air Pollution Zones and Harmful Pollution Levels of Alkaline Dust for Plants

For characterisation of landscapes in north-eastern Estoniaaffected by alkaline oil shale fly ash and cement dust the zonation-method based on average annual (C _y) and short-termconcentrations of pollutants in the air was used, as well as on deposition loads of dust and Ca²⁺. In the overground layer of atmosphere the zones with different air pollution loads were distinguished. A comparative analysis of pollution zones characteristics and biomonitoring data revealed that for sensitive lichen the dangerous level of alkaline dust in the air, introducingthe degradation of Sphagnum sp. at the level of C _y of dust 10–20 g m^-3 and at 0.5–1 hr maximums 100–150 g m^-3. For Scots pine (Pinus sylvestris L.) and Norway spruce (Picea abies (L.) Karst.) this limited concentration (decline of growth parameters) of cement dust is correspondingly following: 30–50 g m^-3 and 150–500 g m^-3, in case of fly ash the limit level of C _y amounting 100 g m^-3. Daily deposition load of Ca²⁺ should not exceed approximately 4.5–15 mg m^-2 for lichen; for conifers the harmful pollution load is higher – >22 mg m^-2.     

Early Effects of Atmospheric Ammonia Deposition on Calluna Vulgaris (L.) Hull Growing on an Ombrotrophic Peat Bog

This paper reports data from a field study investigating the impacts of elevated ammonia (NH₃) deposition on Calluna vulgaris growing on an ombrotrophic peat bog in S.E. Scotland. Shoot extension, foliar N concentrations, chlorophyll concentration and chlorophyll fluorescence were measured during the second growing season of exposure to a gradient of ammonia concentrations. Results indicate that NH₃ increases growth between 150–200 kg N ha^–1y^–1 cumulative deposition. Foliar N content increased significantly in response to NH₃ cumulative deposition up to 400 kg N ha^–1 y^–1 whereas chlorophyll a content significantly decreased. Measurements of Fv/Fm suggest that although NH₃ exposure altered the growth and reduced chlorophyll a, the efficiency of photosystem II was insensitive to NH₃-N deposition at this stage.     

Effects of Temperature and Relative Humidity on Polylactic Acid Plastic Degradation

Three high molecular weight (120,000 to 200,000 g mol^–1) polylactic acid (PLA) plastic films from Chronopol (Ch-I) and Cargill Dow Polymers (GII and Ca-I) were analyzed for their degradation under various temperature and relative humidity (RH) conditions. Two sets of plastic films, each containing 11 samples, were randomly hung in a temperature/humidity-controlled chamber by means of plastic-coated paper clips. The tested conditions were 28, 40, and 55°C at 50 and 100% RH, respectively, and 55°C at 10% RH. The three tested PLA films started to lose their tensile properties when their weight-average molecular weight (M _w) was in the range of 50,000 to 75,000 g mol^–1. The average degradation rate of Ch-I, GII, and Ca-I was 28,931, 27,361, and 63,025 M _w/week, respectively. Hence, GII had a faster degradation rate than Ch-I and Ca-I under all tested conditions. The degradation rate of PLA plastics was enhanced by the increase in temperature and relative humidity. This trend was observed in all three PLA plastics (Ca-I, GII, and Ch-I). Of the three tested films, Ch-I was the first to lose its mechanical properties, whereas Ca-I demonstrated the slowest loss, with mechanical properties under all tested conditions.     

Quantifying dry NH3 deposition to an ombrotrophic bog from an automated NH3 field release system

Providing an accurate estimate of the dry component of N deposition to low N background, semi-natural habitats, such as bogs and upland moors dominated by Calluna vulgaris is difficult, but essential to relate nitrogen deposition to effects in these communities. To quantify the effects of NH₃ inputs to moorland vegetation growing on a bog at a field scale, a field release NH₃ fumigation system was established at Whim Moss (Scottish Borders) in 2002. Gaseous NH₃ from a line source was released along of a 60 m transect, when meteorological conditions (wind speed >2.5 m s^–1 and wind direction in the sector 180–215°) were met, thereby providing a profile of decreasing NH₃ concentration with distance from the source. In a complementary study, using a NH₃ flux chamber system, the relationships between NH₃ concentrations and cuticular resistances were quantified for a range of NH₃ concentrations and micrometeorological conditions for moorland vegetation. Cuticular resistances increased with NH₃ concentration from 11 s m^–1 at 3.0 g m^–3 to 30 s m^–1 at 30 g m^–3. The NH₃ concentration data and the concentration-dependent canopy resistance are used to calculate NH₃ deposition taking into account leaf surface wetness. The implications of using an NH₃ concentration-dependent cuticular resistance and the importance for refining critical loads are discussed.     

Linking field experiments to long-term simulation of impacts of nitrogen deposition on heathlands and moorlands

The results from three long-term field manipulation studies of the impacts of increased nitrogen deposition (0–120 kg N ha^–1 yr^–1) on lowland and upland heathlands in the UK were compared, to test if common responses are observed. Consistent increases in Calluna foliar N content and decreases in litter C:N ratios were found across all sites, while increases in N leaching were not observed at any site over the range 0–80 kg ha^–1 yr^–1. However, the response of Calluna biomass did vary between sites, possibly reflecting site differences in nutrient status and management histories. Five versions of a simulation model of heathland responses to N were developed, each reflecting different assumptions about the fate and turnover of soil N. Model outputs supported the deduction from mass balance calculations at two of the field sites that N additions have resulted in an increase in immobilisation; the latter was needed to prevent the model overestimating measured N leaching. However, this version of the model significantly underestimated Calluna biomass. Model versions, which included uptake of organic N by Callunaand re-mobilisation of N from the soil organic store provided some improvement in the fit between modelled and field biomass data, but re-mobilisation also led to an overestimation of N leaching. Quantification of these processes and their response to increased N deposition are therefore critical to interpreting experimental data and predicting the long-term impacts of atmospheric deposition on heathlands and moorlands.     

A Chronology of Nitrogen Deposition in the UK Between 1900 and 2000

Measurements of the concentrations of nitrogen compounds in air and precipitation in the UK have been made since the mid-19th century, but no networks operating to common protocols and having traceable analytical procedures were established until the 1950s. From 1986 onwards, a high-quality network of sampling stations for precipitation chemistry was established across the UK. In the following decade, monitoring networks provided measurement of NO₂, NH₃, HNO₃ and a satisfactory understanding of the dry deposition process for these gases allowed dry deposition to be quantified. Maps of N deposition for oxidized and reduced compounds at a spatial scale of 5 km × 5 km are available from 1986 to 2000. Between 1950 and 1985, the more limited measurements, beginning with those of the European Air Chemistry Network (EACN) provide a reasonable basis to estimate wet deposition of NO ₃ ^– –N and NH ₄ ⁺ –N. For the first half of the century, estimates of deposition were scaled with emissions assuming a constant relationship between emission and deposition for each of the components of the wet and dry deposition budget at the country scale. Emissions of oxidized N, which dominated total nitrogen emissions throughout the century, increased from 312 kt N annually in 1900 to a peak of 787 kt for the decade 1980–1990 and then declined to 460 kt in 2000. Emissions of reduced N, largely from coal combustion were about 168 kt N in 1900, increasing to a peak of 263 kt N in 2000 and by now dominated by agricultural sources. Reduced N dominated the deposition budget at the country scale, increasing from 163 kt N in 1900 to 211 kt N in 2000, while deposition of oxidized N was 66 kt N in 1900 and 191 kt N in 2000. Over the century, 68 Mt (Tg) of fixed N was emitted within the UK, 78% as NO _x , while 29 Mt of nitrogen was deposited (43% of emissions), equivalent to 1.2 t N ha^–1, on average, with 60% in the reduced form. Deposition to semi-natural ecosystems is approximately 15 Tg N, equivalent to between 1 and 5 t N ha^–1, over the century and appears to be accumulating in soil. The N deposition over the century is similar in magnitude to the total soil N inventory in surface horizons.     

Poly(vinyl alcohol)/Compost Composites for Biofiltration of Swine Waste Volatiles

In this study, a Poly(vinyl alcohol)(PVA)/compost composite bead is prepared and is indicated suitable as a filter material for biofiltration. The optimal preparation process is with the compost size of 16–35 mesh, the ratio of water to compost of 40 g/15 g compost, and the immersion time in the phosphate solution of 60 min. The composite bead prepared by this process is a porous spherical particle with a diameter between 2.4 and 6.0 mm and a density of 0.96 g/cm³. It contains 9.43 mg P/g dry solid and 12.1 mg N/g dry solid. The equilibrium moisture content of the composite bead bed from adsorption and holding experiments is 50.5 and 54.6% on a wet basis respectively, which is about 1.74 times higher than that of swine manure compost bed. It corresponds to the optimal filter material required and is sufficient to sustain biological activity as the composite bead adsorbs equilibrium moisture. The bulk compressive strength of the composite bead bed is about 1.15 times larger than that of swine manure compost bed to ensure even distribution of air flow and reduce the head loss as the air flow stream passed through. The pH value of the filter bed could maintain in the 6.9–7.2 range during the operation period due to the composite bead has the phosphate buffer capacity. The percentage of ethyl acetate removal could remain at over 99% for 40 days operation while the composite beads adsorbed inorganic nitrate nutrients. The pressure drop of two kind composite beads and pig manure compost filter beds are 0 and 2 mm H₂O, respectively, after operating for 40 days.     

A New Type Synthetic Filter Material for Biofilter: Preparation and its Characteristic Analysis

In this study, a new type poly(vinyl alcohol)/peat composite bead is prepared and is shown suitable as a filter material for biofiltration. The optimal preparation condition is with the peat size of 16–35 mesh, the ratio of water to peat of 40g water/10 peat and the immersion time in the phosphate solution of 30min. The composite bead prepared by this process is a porous spherical particle with a density of 0.692 g/cm³. It contains phosphor and nitrogen nutrient are 2.91mg P/g dry solid and 3.25mg N/g dry solid, respectively. The diameter of composite bead is between 2.4 and 6.0mm and the average diameter is about 4.0mm. The equilibrium moisture content of the bead from adsorption and holding experiments are 50.5 and 66.8% on a wet basis, respectively, corresponding to the optimal filter material required and is sufficient to sustain biological activity as the bead adsorbs equilibrium moisture. The composite bead has higher moisture holding capacity and the compression strength than the pig manure compost filter material. The composite bead has buffer capacity and could maintain the filter bed at pH = 6.9–7.2 during the operation period. The percentage of removed ethyl acetate could stay at over 99% for 33 days operation while the composite bead adsorbed inorganic nitrate nutrient.     

Accumulation of Heavy Metals by in vitro cultures of plants

The aim of the project is to study heavy metals accumulation by the selected plants in both laboratory and field conditions. Within the experiments the aspen (Populus tremula × tremuloides), sunflower (Helianthus annuus) and corn (Zea mays) plants were studied. The reasons for this selection were: a fast growth of these plants, an accumulation capacity and an ability to survive in different types of soils. The study was carried out on the aspen plantlets grown in vitro. The plants were exposed to the aqueous solutions having concentrations 0.1 mM, 0.5 mM of Pb²⁺ or Ni²⁺, respectively. The accumulation capacityfor aspen, was about 70% of Pb²⁺ originally present in the solution. The starting concentration of Pb²⁺ (0.5 mM) exhibited no negative impact on the growth. Besides in vitro expositions, a pilot-scale phytoremediation experiment was carried out at the polluted industrial area (Zn – 75000 mg/kg), (Pb – 16000 mg/kg), (Cr – 590 mg/kg), (Cd – 90 mg/kg) and (Cu – 1700 mg/kg).     

Field scale N2O flux measurements from grassland using eddy covariance

In order to assess nitrous oxide (N₂O) emissions from typical intensively managed grassland in northern Britain fluxes were measured by eddy covariance using tuneable diode laser absorption spectroscopy from June 2002 to June 2003 for a total period of 4000 h. With micrometeorological techniques it is possible to obtain a very detailed picture of the fluxes of N₂O at field scale (10³–10⁴ m²), which are valuable for extrapolation to regional scales. In this paper three of the four fertilizer applications were investigated in detail. N₂O emissions did not always show a clear response. Hourly fluxes were very large immediately after the June 2002 nitrogen fertilizer application, peaking at 2.5 mg N₂O–N m^–2 s^–1. Daily fluxes were averaging about 300 ng N₂O m^–2 s^–1 over the 4 days following fertilizer application. The response of N₂O emissions was less evident after the August fertilization, although 2 days after fertilizer application an hourly maximum flux of 554 ng N₂O–N m^–2 s^–1 was registered. For the rest of August the flux was undetectable. The differences between fertilization events can be explained by different environmental conditions, such as soil temperature and rainfall. A fertiliser-induced N₂O emission was not observed after fertilizer application in March 2003, due to lack of rainfall. The total N₂O flux from June 2002 to June 2003 was 5.5 kg N₂O–N ha^–1y^–1, which is 2.8% of the total annual N fertilizer input.     

Modelling of Air Quality with CAMx: A Case Study in Switzerland

The three-dimensional Eulerian model CAMx (Comprehensive Air QualityModel with Extensions) was applied for the first time to simulate bothgaseous and particulate photochemical air pollution in Switzerland during July 28–30, 1993. The meteorological input data were prepared using the Systems Applications International Mesoscale Model (SAIMM). The CAMx model results were compared with the measurements carried out at ground level andfrom airborne measuring platforms within the frame of the Swiss POLLUMET research programme. In general, the CAMx performance for gaseous species wasfound to be better than that of the previously used Urban Airshed Model (UAM)and the Variable Grid Urban Airshed Model (UAM-V). The most significant improvement for the gaseous species is in the prediction of HNO₃ concentrations, due to the inclusion of aerosol chemistry. Aerosol species such as NO₃ ^-, NH₄ ⁺, SO₄ ^2-, and secondary organic aerosols were calculated in one particle size range (0.04–2.5 m) and compared with a few measurements available. Although July 29 was reasonably well simulated, overestimated wind speeds by SAIMM for July 30 caused a too fast transport of pollutants. Similarly to measurements, significant spatial correlation of the secondarily formed aerosols with ozone and formaldehyde is found in the afternoon.     

Accumulation of pollutant nitrogen in calcareous and acidic grasslands: Evidence from N flux and 15N tracer studies

Semi-natural calcareous and acidic grasslands are known to be sensitive to increased atmospheric N deposition. However, the fate of pollutant N within these systems is unknown. This paper reports on the first studies to determine the fate of added N within a calcareous and an acidic grassland subject to long-term simulated enhanced N deposition. Intact soil/turf cores were removed from field plots treated for six years with enhanced N deposition (ambient +0, +35 and +140 kg N ha^–1 year^–1). Cores were inserted into lysimeters and output fluxes of N were monitored in detail. Complete N budgets—calculated from the N flux data—showed considerable accumulation of N within the treated grasslands, up to 76% and 38% of pollutant N in the calcareous and acidic grasslands respectively. In the second study, the short-term (21 day) fate of pollutant N was determined by tracing ¹⁵N labelled ammonium nitrate (+35 kg N ha^–1 year^–1) though the acidic and calcareous lysimeters into plant, soil and leachate pools. Up to 91% and 59% of ¹⁵N was recovered in soils and vegetation of the calcareous and acidic grasslands respectively, with negligible amounts recovered in soil extractable ammonium and nitrate (<0.3%) and in leachate (<0.02%). This rapid short-term immobilisation of pollutant N supports the long-term accumulation of the element calculated from the N flux study.     

Properties and biodegradability of chain-extended copoly(succinic anhydride/ethylene oxide)

Chain-extension reactions were carried out using titanium-iso-propoxide (TIP) as a catalyst for a series of polyesters or copolyesterethers with low molecular weights (M _n =1500–10,000) synthesized by the ring-opening copolymerization of succinic anhydride (SA) with ethylene oxide (EO). The copolymers having aM _n from 25,000 to 50,000 of different properties were obtained. Both the melting point (T _m ) and the fusion heat (H), which indicate the crystallinity of the copolymers, rose with an increase in SA content in the copolymers. Semitransparent films were prepared by compression molding of the copolymers. The biodegradation of the copolymer films was evaluated by enzymatic hydrolysis by lipases and by an aerobic gas evolution test in standard activated sludge. The hydrolyzability of these copolymers by three kinds of lipases was affected by their copolymer composition SA/EO, form, andM _n . The copolyesterether (SA/EO=43/57,M _n =48,900) was more easily biodegraded by standard activated sludge compared to the polyester (SA/EO=47/53,M _n =36,300).Presented at the Pacifichem-95, December 17–22, 1995, Honolulu, Hawaii.     

Novel Biobased Polyurethanes Synthesized from Soybean Phosphate Ester Polyols: Thermomechanical Properties Evaluations

Biobased polyurethanes from soybean oil–derived polyols and polymeric diphenylmethane diisocyanate (pMDI) are prepared and their thermomechanical properties are studied and evaluated. The cross-linked biobased polyurethanes being prepared from soy phosphate ester polyols with hydroxyl contents ranging from 122 to 145 mg KOH/g and pMDI within 5 min of reaction time at 150°C in absence of any catalyst show cross-linking densities ranging from 1.8 × 10³ to 3.0 × 10³ M/m³, whereas glass transition temperatures vary from approximately 69 to 82°C. The loss factor (tan ) curves show single peaks for all these biobased polyurethanes, thus indicating a single-phase system. The storage moduli (G) at 30°C range from 4 × 10⁸ to 1.3 × 10⁹ Pa. Upon postcure at 150°C, the thermomechanical properties can be optimized. Cross-link densities are improved significantly for hydroxyl content of 139 and 145 mg KOH/g at curing time of 24 h. Similarly, glass transition temperature (T_g) and storage moduli around and after T_g are increased. Meanwhile, tan intensities decrease as result of restricted chain mobility. Longer exposure time (24 h) induces thermal degradation, as evidenced by thermogravimetric analysis (TGA). The dynamic mechanical (DMA) analysis shows that postcure at 100°C for times exceeding 24 h also leads to improved properties. However, cross-linking densities are lower compared to postcure carried out at 150°C.     

Carbon Sequestration: Do N Inputs and Elevated Atmospheric CO2 Alter Soil Solution Chemistry and Respiratory C Losses?

Soil respiration is a large C flux which is of primary importance in determining C sequestration. Here we ask how it is altered by atmospheric CO₂ concentration and N additions. Swards of Lolium perenne L. were grown in a Eutric cambisol under controlled conditions with and without the addition of 200 kg NO ₃ ^– –N ha^–1, at either 350 ppm or 700 ppm CO₂, for 3 months. Soil respiration and net canopy photosynthesis were both increased by added N and elevated CO₂, but soil respiration increased proportionately less than fixation by photosynthesis. Thus, both elevated CO₂ and N appeared to increase potential C sequestration, although adding N at elevated CO₂ reduced the C sequestered as a proportion of that fixed relative to elevated CO₂ alone. Across all treatments below-ground respiratory C losses were predicted by root biomass, but not by soil solution C and N concentrations. Specific root-dependent respiration was increased by elevated CO₂, such that belowg-round respiration per unit biomass and per unit plant N was increased.     

Controls on Leaching of N Species in Upland Moorland Catchments

Spatial and temporal changes in mobility of N species have been studied for three UK upland river networks, the Etherow in the South Pennines, the Nether Beck in the Lake District and the Dee in NE Scotland. The catchments are subject to N deposition at 35.1, 22.0 and 10.8–15.6 kg N ha^–1 yr^–1, respectively. TheNH ₄ ⁺ leaching appears to be predominantly regulated by flowpath in more polluted upland catchments. It is greatest where water draining acidified peaty soils contributes more to total discharge. Soluble organic matter may provide the dominant counter anion. In the Etherowand Dee catchments, which are dominated by acid mineral and organic soils, at high discharge NO ₃ ^– also appears to be associated with greater input of water from acidified soils. In contrast, for the Nether Beck, higher NO ₃ ^– concentrations are associated with tributaries draining soils contributingwater with higher alkalinity, suggesting nitrification is important. For the Etherow and Dee, dissolved organic N (DON) appears to originate predominantly from acidified, peaty soils. Spiking experiments with peat soil from the Etherow catchment confirmed the limited capacity of these soils to utilize inorganic N inputs, favouring equilibration with NH ₄ ⁺ inputs and leaching losses of inorganic N throughout the year.     

Applying metabolic fingerprinting to ecology: The use of Fourier-transform infrared spectroscopy for the rapid screening of plant responses to N deposition

The potential for metabolic fingerprinting via Fourier-transform infrared (FT-IR) spectroscopy to provide a novel approach for the detection of plant biochemical responses to N deposition is examined. An example of spectral analysis using shoot samples taken from an open top chamber (OTC) experiment simulating wet ammonium deposition is given. Sample preparation involved oven drying and homogenisation via mill grinding. Slurries of a consistent dilution were then prepared prior to FT-IR analysis. Spectra from control, 8 and 16 kg N ha^–1 yr^–1 treatments were then subjected to cross-validated discriminant function analysis. Ordination diagrams showed clear separation between the three N treatments examined. The potential for using Calluna vulgaris (L.) Hull as a bioindicator of N deposition is further evident from these results. The results also clearly demonstrate the power of FT-IR in discriminating between subtle phenotypic alterations in overall plant biochemistry as affected by ammonium pollution.     

Protozooplankton in the Deep Oligotrophic Traunsee (Austria) Influenced by Discharges of Soda and Salt Industries

Traunsee is a deep oligotrophic lake in Austria characterised by an artificial enrichment of chloride in the hypolimnion (up to 170 mg L^-1) caused by waste disposal of soda and salt industries. Protists were collected monthly over one year, observed alive and after Quantitative Protargol Staining (ciliates) or via epifluorescence microscopy (heterotrophic flagellates). Three sites within the lake (0–40 m depths) were compared to deeper water layers from 60–160 m depths where chloride concentrations and conductivity were increased. In addition, we observed the protozooplankton of two neighbouring lakes, i.e. reference systems, during one sampling occasion. In Traunsee the abundance of ciliates was low (200–36 600 cells L^-1) in contrast to high species diversity (at least 60 different species; H_S = 2.6) throughout the year. The main pelagic species in terms of abundance were small oligotrichs and prostomatids like Rimostrombidium brachykinetum/hyalinum, Balanion planctonicum and Urotricha spp. throughout the investigation period. Among free-living heterotrophic flagellates, which occurred at densities of 40–2800 cells mL^-1, small morphotypes dominated in the pelagial. No differences at the community level between the three lakes could be observed and pelagic ciliates and flagellates seemed not to be affected by increased chloride concentrations or by enhanced conductivity.     

The Influence of Atmospheric N Deposition on Nitrous Oxide and Nitric Oxide Fluxes and Soil Ammonium and Nitrate Concentrations

The deposition of atmospheric N to soils provides sources of available N to the nitrifying and denitrifying microbial community and subsequently influences the rate of NO and N₂O emissions from soil. We have investigated the influence of three different sources of enhanced N deposition on NO and N₂O emissions 1) elevated NH₃ deposition to woodlands downwind of poultry and pig farms, 2) increased wet cloud and occult N deposition to upland forest and moorland and 3) enhanced N deposition to trees as NO ₃ ^– and NH ₄ ⁺ aerosol. Flux measurements of NO and N₂O were made using static chambers in the field or intact and repacked soil cores in the laboratory and determination of N₂O by gas chromatography and of NO by chemiluminescence analysis. Rates of N deposition to our study sites were derived from modelled estimates of N deposition, NH₃ concentrations measured by passive diffusion and inference from measurements of the ²¹⁰Pb inventory of soils under tree canopies compared with open grassland. NO and N₂O emissions and KCl-extractable soil NH ₄ ⁺ and NO ₃ ^– concentrations all increased with increasing N deposition rate. The extent of increase did not appear to be influenced by the chemical form of the N deposited. Systems dominated by dry-deposited NH₃ downwind of intensive livestock farms or wet-deposited NH ₄ ⁺ and NO ₃ ^– in the upland regions of Britain resulted in approximately the same linear response. Emissions of NO and N₂O from these soils increased with both N deposition and KCl extractable NH ₄ ⁺ , but the relationship between NH ₄ ⁺ and N deposition (ln NH ₄ ⁺ = 0.62 ln N_deposition + 0.21, r ² = 0.33, n = 43) was more robust than the relationship between N deposition and soil NO and N₂O fluxes.