Impacts of advanced treatment processes on elimination of antibiotic resistance genes in a municipal wastewater treatment plant

The distributions of ARGs were monitored in a WWTP in Harbin during six months. CASS had the best removal efficacy of ARGs compared to other processes in the WWTP. UV disinfection could effectively control the HGT. AGAC significantly remove ARGs and organics due to its high absorption capacity. Combination of ozone and AGAC significantly improve removal of ARGs and organics. Antibiotic resistance genes (ARGs) pose a serious threat to public health. Wastewater treatment plants (WWTPs) are essential for controlling the release of ARGs into the environment. This study investigated ARG distribution at every step in the treatment process of a municipal WWTP located in Harbin for six consecutive months. Changes in ARG distribution involved in two advanced secondary effluent treatment processes, ozonation and granular activated carbon (GAC) adsorption, were analyzed. Biological treatment resulted in the highest ARG removal (0.76–1.94 log reduction), followed by ultraviolet (UV) disinfection (less than 0.5-log reduction). Primary treatment could not significantly remove ARGs. ARG removal efficiency increased with an increase in the ozone dose below 40 mg/L. However, amorphous GAC (AGAC) adsorption with a hydraulic retention time (HRT) of 1 h showed better removal of ARGs, total organic carbon (TOC), total nitrogen (TN), and total phosphorus (TP) than ozonation at a 60 mg/L dose. UV treatment could efficiently reduce the relative ARG abundance, despite presenting the lowest efficiency for the reduction of absolute ARG abundance compared with GAC and ozone treatments. The combination of ozone and AGAC can significantly improve the removal of ARGs, TOC, TN and TP. These results indicate that a treatment including biological processing, ozonation, and AGAC adsorption is a promising strategy for removing ARGs and refractory organic substances from sewage.     

Metagenomic analysis on resistance genes in water and microplastics from a mariculture system

• Total 174 subtypes of ARGs were detected by metagenomic analysis. • Chloramphenicol resistance genes were the dominant ARGs in water and microplastics. • The abundances of MRGs were much higher than those of ARGs. • Proteobacteria, Bacteroidetes, and Actinobacteria were the dominant phylum. • Microplastics in mariculture system could enrich most of MRGs and some ARGs. Microplastics existing widely in different matrices have been regarded as a reservoir for emerging contaminants. Mariculture systems have been observed to host microplastics and antibiotic resistance genes (ARGs). However, more information on proliferation of ARGs and metal resistance genes (MRGs) in mariculture system at the presence of microplastics is needed. This study used metagenomic analysis to investigate the distribution of ARGs and MRGs in water and microplastics of a typical mariculture pond. Total 18 types including 174 subtypes of ARGs were detected with the total relative abundances of 1.22/1.25 copies per 16S rRNA copy for microplastics/water. Chloramphenicol resistance genes were the dominant ARGs with the abundance of 0.35/0.42 copies per 16S rRNA copy for microplastics/water. Intergron intI1 was dominant gene among 6 detected mobile genetic elements (MGEs) with the abundance of 75.46/68.70 copies per 16S rRNA copy for water/microplastics. Total 9 types including 46 subtypes of MRGs were detected with total abundance of 5.02 × 10²/6.39 × 10² copies per 16S rRNA copy for water/ microplastics while genes resistant to copper and iron served as the dominant MRGs. Proteobacteria, Bacteroidetes, and Actinobacteria accounted for 84.2%/89.5% of total microbial community. ARGs with relatively high abundance were significantly positively related to major genera, MGEs, and MRGs. Microplastics in mariculture system could enrich most of MRGs and some ARGs to serve as potential reservoir for these pollutants. The findings of this study will provide important information on resistance gene pollution at presence of microplastics in the mariculture system for further proposing suitable strategy of environmental management.     

Presence,dissemination and removal of antibiotic resistant bacteria and antibiotic resistance genes in urban drinking water system: A review

Reviewed the change of ARGs and ARB in full-scale urban drinking water systems. Conventional processes are more promising than BAC process in ARGs removal. Mechanisms of ARGs enrichment and spread in BAC filter and DWDSs are discussed. Raise the need of future research on ARGs and ARB change in building plumbing systems. Antibiotic resistance in aquatic environment has become an important pollution problem worldwide. In recent years, much attention was paid to antibiotic resistance in urban drinking water systems due to its close relationship with the biosafety of drinking water. This review was focused on the mechanisms of antibiotic resistance, as well as the presence, dissemination and removal of antibiotic resistant bacteria (ARB) and antibiotic resistance genes (ARGs) in the urban drinking water system. First, the presence of ARB and ARGs in the drinking water source was discussed. The variation of concentration of ARGs and ARB during coagulation, sedimentation and filtration process were provided subsequently, in which filtration was proved to be a promising technology to remove ARGs. However, biological activated carbon (BAC) process and drinking water distribution systems (DWDSs) could be incubators which promote the antibiotic resistance, due to the enrichment of ARGs and ARB in the biofilms attached to the active carbon and pipe wall. Besides, as for disinfection process, mechanisms of the inactivation of ARB and the promotion of conjugative transfer of ARGs under chlorine, ozone and UV disinfection were described in detail. Here we provide some theoretical support for future researches which aim at antibiotic resistance controlling in drinking water.     

Characterization of value-added chemicals derived from the thermal hydrolysis and wet oxidation of sewage sludge

• Hydrothermal treatment can greatly improve resource recovery from sewage sludge. • tCOD removal during WO was ~55% compared with ~23% after TH. • TOC solubilization during hydrothermal treatment followed first-order kinetics. • Solids and carbon balance confirmed loss of organics during thermal hydrolysis. • Reaction pathways for thermal hydrolysis and wet oxidation are proposed. We evaluated the effect of hydrothermal pretreatments, i.e., thermal hydrolysis (TH) and wet oxidation (WO) on sewage sludge to promote resource recovery. The hydrothermal processes were performed under mild temperature conditions (140°C–180°C) in a high pressure reactor. The reaction in acidic environment (pH= 3.3) suppressed the formation of the color imparting undesirable Maillard’s compounds. The oxidative conditions resulted in higher volatile suspended solids (VSS) reduction (~90%) and chemical oxygen demand (COD) removal (~55%) whereas TH caused VSS and COD removals of ~65% and ~27%, respectively at a temperature of 180°C. During TH, the concentrations of carbohydrates and proteins in treated sludge were 400–1000 mg/L and 1500–2500 mg/L, respectively. Whereas, WO resulted in solids solubilization followed by oxidative degradation of organics into smaller molecular weight carboxylic acids such as acetic acid (~400–500 mg/L). Based on sludge transformation products generated during the hydrothermal pretreatments, simplified reaction pathways are predicted. Finally, the application of macromolecules (such as proteins), VFAs and nutrients present in the treated sludge are also discussed. The future study should focus on the development of economic recovery methods for various value-added compounds.     

Degradation of extracellular genomic,plasmid DNA and specific antibiotic resistance genes by chlorination

Extracellular DNA structure damaged by chlorination was characterized. Integrity of extracellular ARG genetic information after chlorination was determined. Typical chlorine doses will likely effectively diminish extracellular DNA and ARGs. Plasmid DNA/ARGs were less readily broken down than genomic DNA. The Bioanalyzer methodology effectively documented damage incurred to DNA. There is a need to improve understanding of the effect of chlorine disinfection on antibiotic resistance genes (ARGs) in order to advance relevant drinking water, wastewater, and reuse treatments. However, few studies have explicitly assessed the physical effects on the DNA. Here we examined the effects of free chlorine (1–20 mg Cl₂/L) on extracellular genomic, plasmid DNA and select ARGs. Chlorination was found to decrease the fluorometric signal of extracellular genomic and plasmid DNA (ranging from 0.005 to 0.05 mg/mL) by 70%, relative to a no-chlorine control. Resulting DNA was further subject to a fragment analysis using a Bioanalyzer, indicating that chlorination resulted in fragmentation. Moreover, chlorine also effectively deactivated both chromosomal- and plasmid-borne ARGs, mecA and tetA, respectively. For concentrations >2 mg Cl₂//L × 30 min, chlorine efficiently reduced the qPCR signal when the initial concentration of ARGs was 10⁵ copies/mL or less. Notably, genomic DNA and mecA gene signals were more readily reduced by chlorine than the plasmid-borne tetA gene (by ~2 fold). Based on the results of qPCR with short (~200 bps) and long amplicons (~1200 bps), chlorination could destroy the integrity of ARGs, which likely reduces the possibility of natural transformation. Overall, our findings strongly illustrate that chlorination could be an effective method for inactivating extracellular chromosomal- and plasmid-borne DNA and ARGs.     

Sludge fermentation liquid addition attained advanced nitrogen removal in low C/N ratio municipal wastewater through short-cut nitrification-denitrification and partial anammox

• Sludge fermentation liquid addition resulted in a high NAR of 97.4%. • Extra NH₄⁺-N from SFL was removed by anammox in anoxic phase. • Nitrogen removal efficiency of 92.51% was achieved in municipal wastewater. • The novel system could efficiently treat low COD/N municipal wastewater. Biological nitrogen removal of wastewater with low COD/N ratio could be enhanced by the addition of wasted sludge fermentation liquid (SFL), but the performance is usually limited by the introducing ammonium. In this study, the process of using SFL was successfully improved by involving anammox process. Real municipal wastewater with a low C/N ratio of 2.8–3.4 was treated in a sequencing batch reactor (SBR). The SBR was operated under anaerobic-aerobic-anoxic (AOA) mode and excess SFL was added into the anoxic phase. Stable short-cut nitrification was achieved after 46d and then anammox sludge was inoculated. In the stable period, effluent total inorganic nitrogen (TIN) was less than 4.3 mg/L with removal efficiency of 92.3%. Further analysis suggests that anammox bacteria, mainly affiliated with Candidatus_Kuenenia, successfully reduced the external ammonia from the SFL and contributed approximately 28%–43% to TIN removal. Overall, this study suggests anammox could be combined with SFL addition, resulting in a stable enhanced nitrogen biological removal.     

Environmental effects and risk control of antibiotic resistance genes in the organic solid waste aerobic composting system: A review

• ARGs were detected in livestock manure, sludge, food waste and fermentation dregs. • The succession of microbial community is an important factor affecting ARGs. • Horizontal transfer mechanism of ARGs during composting should be further studied. Antibiotic resistance genes (ARGs) have been diffusely detected in several kinds of organic solid waste, such as livestock manure, sludge, antibiotic fermentation residues, and food waste, thus attracting great attention. Aerobic composting, which is an effective, harmless treatment method for organic solid waste to promote recycling, has been identified to also aid in ARG reduction. However, the effect of composting in removing ARGs from organic solid waste has recently become controversial. Thus, this article summarizes and reviews the research on ARGs in relation to composting in the past 5 years. ARGs in organic solid waste could spread in different environmental media, including soil and the atmosphere, which could widen environmental risks. However, the conventional composting technology had limited effect on ARGs removal from organic solid waste. Improved composting processes, such as hyperthermophilic temperature composting, could effectively remove ARGs, and the HGT of ARGs and the microbial communities are identified as vital influencing factors. Currently, during the composting process, ARGs were mainly affected by three response pathways, (I) “Microenvironment-ARGs”; (II) “Microenvironment-microorganisms-ARGs”; (III) “Microorganisms-horizontal gene transfer-ARGs”, respectively. Response pathway II had been studied the most which was believed that microbial community was an important factor affecting ARGs. In response pathway III, mainly believed that MGEs played an important role and paid less attention to eARGs. Further research on the role and impact of eARGs in ARGs may be considered in the future. It aims to provide support for further research on environmental risk control of ARGs in organic solid waste.     

Aggravation of membrane fouling and methane leakage by a three-phase separator in an external anaerobic ceramic membrane bioreactor

The existence of three-phase separator did not affect COD removal in the EAnCMBR. The existence of three-phase separator aggravated methane leakage of EAnCMBR. The existence of three-phase separator aggravated membrane fouling rate of EAnCMBR. Start-up of EAnCMBR equipped three-phase separator was slightly delayed. The three-phase separator is a critical component of high-rate anaerobic bioreactors due to its significant contribution in separation of biomass, wastewater, and biogas. However, its role in an anaerobic membrane bioreactor is still not clear. In this study, the distinction between an external anaerobic ceramic membrane bioreactor (EAnCMBR) unequipped (R1) and equipped (R2) with a three-phase separator was investigated in terms of treatment performance, membrane fouling, extracellular polymers of sludge, and microbial community structure. The results indicate that the COD removal efficiencies of R1 and R2 were 98.2%±0.4% and 98.1%±0.4%, respectively, but the start-up period of R2 was slightly delayed. Moreover, the membrane fouling rate of R2 (0.4 kPa/d) was higher than that of R1 (0.2 kPa/d). Interestingly, the methane leakage from R2 (0.1 L/d) was 20 times higher than that from R1 (0.005 L/d). The results demonstrate that the three-phase separator aggravated the membrane fouling rate and methane leakage in the EAnCMBR. Therefore, this study provides a novel perspective on the effects of a three-phase separator in an EAnCMBR.     

Effective removal of Cd2+ and Pb2+ pollutants from wastewater by dielectrophoresis-assisted adsorption

Dielectrophoresis (DEP) process could enhance the removal the Cd²⁺ and Pb²⁺ with less absorbent. The removal rates of both Cd²⁺ and Pb²⁺ increased with the increase of voltage. The overall removal rate of Cd²⁺ and Pb²⁺ in the binary system is higher than that of Cd²⁺ or Pb²⁺ in the single system. DEP could cause considerable changes of the bentonite particles in both surface morphology and microstructure. Dielectrophoresis (DEP) was combined with adsorption (ADS) to simultaneously and effectively remove Cd²⁺ and Pb²⁺ species from aqueous solution. To implement the process, bentonite particles of submicro-meter size were used to first adsorb the heavy metal ions. These particles were subsequently trapped and removed by DEP. The effects of the adsorbent dosage, DEP cell voltage and the capture pool numbers on the removal rate were investigated in batch processes, which allowed us to determine the optimal experimental conditions. The high removal efficiency, 97.3% and 99.9% for Cd²⁺ and Pb²⁺, respectively, were achieved when the ions are coexisting in the system. The microstructure of bentonite particles before and after ADS/DEP was examined by scanning electron microscopy. Our results suggest that the dielectrophoresis-assisted adsorption method has a high capability to remove the heavy metals from wastewater.     

Optimized determination of airborne tetracycline resistance genes in laboratory atmosphere

• Sampling parameters with high efficiency was determined. • Operational process to detect airborne ARGs was optimized. • Providing research basis to control airborne ARGs of a laboratory atmosphere Antibiotic resistance genes (ARGs) have been detected in various atmospheric environments. Airborne ARGs transmission presents the public health threat. However, it is very difficult to quantify airborne ARGs because of the limited availability of collectable airborne particulate matter and the low biological content of samples. In this study, an optimized protocol for collecting and detecting airborne ARGs was presented. Experimental results showed that recovery efficiency tended to increase initially and then declined over time, and a range of 550–780 copies/mm² of capture loading was recommended to ensure that the recovery efficiency is greater than 75%. As the cell walls were mechanically disrupted and nucleic acids were released, the buffer wash protects ARGs dissolution. Three ratios of buffer volume to membrane area in buffer wash were compared. The highest concentrations of airborne ARGs were detected with 1.4 µL/mm² buffer wash. Furthermore, the majority of the cells were disrupted by an ultrasonication pretreatment (5 min), allowing the efficiency ARGs detection of airborne samples. While, extending the ultrasonication can disrupt cell structures and gene sequence was broken down into fragments. Therefore, this study could provide a theoretical basis for the efficient filter collection of airborne ARGs in different environments. An optimized sampling method was proposed that the buffer wash was 1.4 µL/mm² and the ultrasonication duration was 5 min. The indoor airborne ARGs were examined in accordance with the improved protocol in two laboratories. The result demonstrated that airborne ARGs in an indoor laboratory atmosphere could pose the considerable health risk to inhabitants and we should pay attention to some complicated indoor air environment.     

Effects of Al3+ on pollutant removal and extracellular polymeric substances (EPS) under anaerobic,anoxic and oxic conditions

The highest removal efficiencies of COD and TN were achieved under 10 mg/L of Al³⁺. The highest TP removal efficiency occurred under 30 mg/L of Al³⁺. EPS, PS and PN concentrations increased with the addition of Al³⁺. Sludge properties significantly changed with the addition of Al³⁺. Aluminum ions produced by aluminum mining, electrolytic industry and aluminum-based coagulants can enter wastewater treatment plants and interact with activated sludge. They can subsequently contribute to the removal of suspended solids and affect activated sludge flocculation, as well as nitrogen and phosphorus removal. In this study, the effects of Al³⁺ on pollutant removal, sludge flocculation and the composition and structure of extracellular polymeric substances (EPS) were investigated under anaerobic, anoxic and oxic conditions. Results demonstrated that the highest chemical oxygen demand (COD) and total nitrogen (TN) removal efficiencies were detected for an Al³⁺ concentration of 10 mg/L. In addition, the maximal dehydrogenase activity and sludge flocculation were also observed at this level of Al³⁺. The highest removal efficiency of total phosphorus (TP) was achieved at an Al³⁺ concentration of 30 mg/L. The flocculability of sludge in the anoxic zone was consistently higher than that in the anaerobic and oxic zones. The addition of Al³⁺ promoted the secretion of EPS. Tryptophan-like fluorescence peaks were detected in each EPS layer in the absence of Al³⁺. At the Al³⁺ concentration of 10 mg/L, fulvic acid and tryptophan fluorescence peaks began to appear, while the majority of protein species and the highest microbial activity were also detected. Low Al³⁺ concentrations (<10 mg/L) could promote the removal efficiencies of COD and TN, yet excessive Al³⁺ levels (>10 mg/L) weakened microbial activity. Higher Al³⁺ concentrations (>30 mg/L) also inhibited the release of phosphorus in the anaerobic zone by reacting with PO₄^3-.     

Enhanced nitrification in integrated floating fixed-film activated sludge (IFFAS) system using novel clinoptilolite composite carrier

Novel carriers with favorable electrophilicity and hydrophilicity were prepared. Novel carriers had the capability of nitrification-enhancing. NH₄⁺-N removal efficiency of IFFAS process rose up to 20% with novel carriers. Nitrosomonadales and Nitrospirales were identified as the functional nitrifiers. The population of Nitrospirales increased by 4.51%. The integrated floating fixed-film activated sludge (IFFAS) process is an ideal preference for nitrification attributing to the longer sludge age for nitrifiers. However, as the core of this process, conventional carriers made of polymer materials usually exhibit negative charge and hydrophobicity on the surface, which is unbeneficial to nitrifying biofilm formation. In this study, novel clinoptilolite composite carriers with favorable hydrophilicity, positive charge and nitrification-enhancing capability were made and implemented in IFFAS system. In comparison with conventional carriers, the novel clinoptilolite composite carriers displayed positive charges on the surface (11.7±1.1 mV, pH 7.0) with increased hydrophilicity (surface contact angle dropped to 76.7°). The novel-carriers-based reactors achieved significantly better NH₄⁺-N removal efficiency at different influent concentrations, dissolved oxygen (DO) levels and shock loads (NH₄⁺-N removal efficiency rose up to 20% comparing with the control reactors filled with polyethylene (PE) carriers or activated sludge). High-throughput sequencing (HTS) results indicated the novel clinoptilolite composite carriers provided favorable niche for more types of bacteria, especially for Nitrosomonadales and Nitrospirales (the functional nitrifiers in the system). The population of Nitrospirales increased by 4.51% by using novel clinoptilolite composite carriers comparing with using PE carriers, which ensured enhanced nitrification process. This study was expected to provide a practical option for enhancing wastewater nitrification performance with the novel clinoptilolite composite carrier.     

Fate and risk assessment of emerging contaminants in reclaimed water production processes

• PPCPs had the highest removal efficiency in A²O combined with MBR process (86.8%). • ARGs and OPFRs were challenging to remove (6.50% and 31.0%, respectively). • Octocrylene and tris(2-ethylhexyl) phosphate posed high risks to aquatic organisms. • Meta-analysis was used to compare the ECs removal in wastewater treatment. • Membrane treatment technology is the most promising treatment for ECs removal. Reclaimed water has been widely applied in irrigation and industrial production. Revealing the behavior of emerging contaminants in the production process of reclaimed water is the first prerequisite for developing relevant water quality standards. This study investigated 43 emerging contaminants, including 22 pharmaceuticals and personal care products (PPCPs), 11 organophosphorus flame retardants (OPFRs), and 10 antibiotic resistance genes (ARGs) in 3 reclaimed wastewater treatment plants (RWTPs) in Beijing. The composition profiles and removal efficiencies of these contaminants in RWTPs were determined. The results indicated that the distribution characteristics of the different types of contaminants in the three RWTPs were similar. Caffeine, sul2 and tris(1-chloro-2-propyl) phosphate were the dominant substances in the wastewater, and their highest concentrations were 27104 ng/L, 1.4 × 10⁷ copies/mL and 262 ng/L, respectively. Ofloxacin and sul2 were observed to be the dominant substances in the sludge, and their highest concentrations were 5419 ng/g and 3.7 × 10⁸ copies/g, respectively. Anaerobic/anoxic/oxic system combined with the membrane bioreactor process achieved a relatively high aqueous removal of PPCPs (87%). ARGs and OPFRs were challenging to remove, with average removal rates of 6.5% and 31%, respectively. Quantitative meta-analysis indicated that tertiary treatment processes performed better in emerging contaminant removal than secondary processes. Diethyltoluamide exhibited the highest mass load discharge, with 33.5 mg/d per 1000 inhabitants. Octocrylene and tris(2-ethylhexyl) phosphate posed high risks (risk quotient>1.0) to aquatic organisms. This study provides essential evidence to screen high priority pollutants and develop corresponding standard in RWTPs.     

Biofiltration and disinfection codetermine the bacterial antibiotic resistome in drinking water: A review and meta-analysis

• Published data was used to analyze the fate of ARGs in water treatment. • Biomass removal leads to the reduction in absolute abundance of ARGs. • Mechanism that filter biofilm maintain ARB/ARGs was summarized. • Potential BAR risks caused by biofiltration and chlorination were proposed. The bacterial antibiotic resistome (BAR) is one of the most serious contemporary medical challenges. The BAR problem in drinking water is receiving growing attention. In this study, we focused on the distribution, changes, and health risks of the BAR throughout the drinking water treatment system. We extracted the antibiotic resistance gene (ARG) data from recent publications and analyzed ARG profiles based on diversity, absolute abundance, and relative abundance. The absolute abundance of ARG was found to decrease with water treatment processes and was positively correlated with the abundance of 16S rRNA (r² = 0.963, p<0.001), indicating that the reduction of ARG concentration was accompanied by decreasing biomass. Among treatment processes, biofiltration and chlorination were discovered to play important roles in shaping the bacterial antibiotic resistome. Chlorination exhibited positive effects in controlling the diversity of ARG, while biofiltration, especially granular activated carbon filtration, increased the diversity of ARG. Both biofiltration and chlorination altered the structure of the resistome by affecting relative ARG abundance. In addition, we analyzed the mechanism behind the impact of biofiltration and chlorination on the bacterial antibiotic resistome. By intercepting influent ARG-carrying bacteria, biofilters can enrich various ARGs and maintain ARGs in biofilm. Chlorination further selects bacteria co-resistant to chlorine and antibiotics. Finally, we proposed the BAR health risks caused by biofiltration and chlorination in water treatment. To reduce potential BAR risk in drinking water, membrane filtration technology and water boiling are recommended at the point of use.     

Degradation of metronidazole by dielectric barrier discharge in an aqueous solution

The discharge characteristics during the degradation of MNZ by DBD were investigated. Increasing the discharge frequency can promote the degradation of MNZ. MNZ removal reaches 99.1% at the initial concentration of 40 ppm within 120 min. Coexisting organic matter inhibits the degradation of MNZ. The energy efficiency of DBD for MNZ removal is higher than other technologies. Degradation of metronidazole (MNZ) which is a representative and stable antibiotic by dielectric barrier discharge (DBD) in an aqueous solution has been studied. Effects of initial MNZ concentration, solution pH and coexisting organics on the degradation were investigated. The results illustrated that increasing the input power and the discharge frequency can improve the removal of MNZ. At low initial concentration, the removal of MNZ can reach up to 99.1%. Acidic and neutral conditions are more favorable for MNZ removal than alkaline condition in the early stage of degradation. However, the difference in MNZ removal between those in acidic or neutral media and that in alkaline one could be neglected with prolonging of the treatment time. Therefore, this method can be applied to MNZ degradation with a wide pH range. Coexisting organic matter in water can attenuate the removal to some extent. This study could provide valuable references for the degradation of nitroimidazole antibiotics by DBD.     

Effect of 2-butenal manufacture wastewater to methanogenic activity and microbial community

The inhibition ratio sharply increased with the increasing COD. The absorbance of UV-vis at 420 nm showed a linear correlation with the SMA. The molecular structure of EPS has changed when COD was 9585 mg/L. Illumina Miseq sequencing was employed to reveal the microbial composition. The synthesis of 2-butenal, which is a vital raw material for the production of sorbic acid as a food preservative, generates some toxic by-products, so it is urgent to seek better detoxification strategies for the treatment of 2-butenal manufacture wastewater. In this study, batch experiments were carried out to investigate the inhibition effect of wastewater on the methanogenic activity. To understand the wastewater toxicity to anaerobic granular sludge, variations of the specific methanogenic activity (SMA) and extracellular polymeric substance (EPS) constituents at various wastewater CODs were investigated. Ultraviolet-visible (UV-vis) spectra and Fourier transform infrared (FT-IR) spectra were employed to analyze the structure of the EPS. The results showed that the inhibitory ratio of 2-butenal manufacture wastewater was less than 8.4% on the anaerobic granular sludge when the CODs were less than 959 mg/L. However, the inhibitory ratio increased from 36.4% to 93.6% when CODs increased from 2396 mg/L to 9585 mg/L, with the SMA decreasing from 39.1 mL CH₄/(gVSS·d) to 3.2 mL CH₄/(gVSS·d). The diversity of the microbial community under various CODs was researched by Illumina 16S rRNA Miseq sequencing and the results demonstrated that Proteiniphilum、Petrimonas and Syntrophobacter were the dominant bacteria genera in all sample. Regarding archaea, Methanobacterium was the most dominated archaea genera, followed by the Methanosaeta group in all samples. Moreover, the bacterial communities had changed obviously with increasing CODs, which indicated high CODs played a negative impact on the richness and diversity of bacterial community in the sludge samples.     

Upgrading VFAs bioproduction from waste activated sludge via co-fermentation with soy sauce residue

SSR addition upgraded VFAs production from WAS. Structure modification by pretreatments led to performance distinctions. Distinctions in microbial community was observed by pretreatments selection. Up to 0.49‒0.65 billion €/year of market value potential was preliminary estimated. Conditioning of extra carbon sources has been widely reported to facilitate fermentation of waste activated sludge (WAS). Soy sauce residue (SSR) was a relatively untapped carbon source for sludge conditioning. This batch study aimed to evaluate the possible implementation of SSR for volatile fatty acids (VFAs) production from WAS. To upgrade the bioavailability of feedstock, three typical pretreatment methods were conducted, i.e., ammonium hydroxide (AH), sulfuric acids (SA) and thermal assisted alkaline (TA). AH pretreated test (AH-PT) outperformed due to a relatively strong structure decomposition of cellulosic materials as revealed by infrared spectroscopic analysis and crystal index. As a result, performed a high hydrolysis rate of 4449 mg COD/d, 1.12-1.23-fold higher than that in TA and SA pretreated tests (TA-PT and SA-PT), and 7.8-fold higher than that in the Control test. Meanwhile, a volatile fatty acids (VFAs) contribution of 401.2 mg COD/g SSR∙L and a maximum acidification rate of 3.59 d^-1 was recorded, with a high sum proportion of mall molecular acetic and propionic 82.2%, 11% ‒70% increase over the other three tests. Besides, speciation process characterized with functional genus differentiation was identified by microbial diversity and distribution investigation and canonical correspondence analysis (CCA). Finally, a potential market value of 0.49‒0.65 Billion €/year was preliminary estimated, showing promise of resource recovery from both WAS and SSR instead of extensive disposal.     

Influences and mechanisms of nanofullerene on the horizontal transfer of plasmid-encoded antibiotic resistance genes between E. coli strains

• Sub-inhibitory levels of nC₆₀ promote conjugative transfer of ARGs. • nC₆₀ can induce ROS generation, oxidative stress and SOS response. • nC₆₀ can increase cell membrane permeability and alter gene expression. • Results provide evidence of nC₆₀ promoting antibiotic resistance dissemination. The spread and development of antibiotic resistance globally have led to severe public health problems. It has been shown that some non-antibiotic substances can also promote the diffusion and spread of antibiotic resistance genes (ARGs). Nanofullerene (nC₆₀) is a type of nanomaterial widely used around the world, and some studies have discovered both the biological toxicity and environmental toxicity of nC₆₀. In this study, cellular and molecular biology techniques were employed to investigate the influences of nC₆₀ at sub-minimum inhibitory concentrations (sub-MICs) on the conjugation of ARGs between the E. coli strains. Compared with the control group, nC₆₀ significantly increased the conjugation rates of ARGs by 1.32‒10.82 folds within the concentration range of 7.03‒1800 mg/L. This study further explored the mechanism of this phenomenon, finding that sub-MICs of nC₆₀ could induce the production of reactive oxygen species (ROS), trigger SOS-response and oxidative stress, affect the expression of outer membrane proteins (OMPs) genes, increase membrane permeability, and thus promote the occurrence of conjugation. This research enriches our understanding of the environmental toxicity of nC₆₀, raises our risk awareness toward nC₆₀, and may promote the more rational employment of nC₆₀ materials.     

Comparison of CNT-PVA membrane and commercial polymeric membranes in treatment of emulsified oily wastewater

CNT-PVA membrane was fabricated and compared with polymeric membranes. The separation performance was evaluated by homemade and cutting fluid emulsions. The three membranes show similar oil retention rates. CNT-PVA membranes have higher permeation fluxes compared with polymeric membranes. CNT-PVA membrane shows higher fouling resistance. Membrane separation is an attractive technique for removal of emulsified oily wastewater. However, polymeric membranes which dominate the current market usually suffer from severe membrane fouling. Therefore, membranes with high fouling resistance are imperative to treat emulsified oily wastewater. In this study, carbon nanotube-polyvinyl alcohol (CNT-PVA) membrane was fabricated. And its separation performance for emulsified oily wastewater was compared with two commercial polymeric membranes (PVDF membrane and PES membrane) by filtration of two homemade emulsions and one cutting fluid emulsion. The results show that these membranes have similar oil retention efficiencies for the three emulsions. Whereas, the permeation flux of CNT-PVA membrane is 1.60 to 3.09 times of PVDF membrane and 1.41 to 11.4 times of PES membrane, respectively. Moreover, after five consecutive operation circles of filtration process and back flush, CNT-PVA membrane can recover 62.3% to 72.9% of its initial pure water flux. However, the pure water flux recovery rates are only 24.1% to 35.3% for PVDF membrane and 6.0% to 26.3% for PES membrane, respectively. Therefore, CNT-PVA membrane are more resistant to oil fouling compared with the two polymeric membranes, showing superior potential in treatment of emulsified oily wastewater.