Determination of solid-liquid partition coefficients (Kd) for the herbicides isoproturon and trifluralin in five UK agricultural soils

Isoproturon and trifluralin are herbicides of contrasting chemical characters and modes of action. Standard batch sorption procedures were carried out to investigate the individual sorption behaviour of 14C-isoproturon and 14C-trifluralin in five agricultural soils (1.8-4.2% OC), and the soil solid-liquid partition coefficients (Kd values) were determined. Trifluralin exhibited strong partitioning to the soil solid phase (Kd range 106-294) and low desorption potential, thus should not pose a threat to sensitive waters via leaching, although particle erosion and preferential flow pathways may facilitate transport. For isoproturon, soil adsorption was low (Kd range 1.96-5.75) and desorption was high, suggesting a high leaching potential, consistent with isoproturon being the most frequently found pesticide in UK surface waters. Soil partitioning was directly related to soil organic carbon (OC) content. Accumulation isotherms were modelled using a dual-phase adsorption model to estimate adsorption and desorption rate coefficients. Associations between herbicides and soil humic substances were also shown using gel filtration chromatography.     

Testing common sediment-porewater distribution models for their ability to predict dissolved concentrations of POPs in The Grenlandsfjords, Norway

This study compares in situ observed porewater concentration of persistent organic pollutants (POPs) with predictions by common solid-water phase distribution models. Bottom sediments were sampled in The Grenlandsfjords, Norway, and the interstitial porewater was isolated from the solids by centrifugation and filtration. Both phases were analysed for polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F), polycyclic aromatic hydrocarbons (PAH), and organic carbon. Based on the sediments' solid phase content of POPs, organic carbon, and soot carbon, we used the organic matter partitioning (OMP), and also the soot and organic matter partitioning (SOMP) model to estimate the porewater concentration. The OMP model gave better agreement to observations than the SOMP model for both PCDD/Fs and PAHs. The observed concentration of the PCDD/Fs in the sediments' porewater was much higher than in the deep water of the fjord. The logarithm of the organic matter-water partitioning coefficent (log K(OC)) in the porewater had positive linear regression on the logarithm of the octanol-water partitioning coefficient (log K(OW)). The slope of the regression model was indistinguishable from 1, except for the PAHs as a group which had a slope less than 1. This contrasts to previous studies undertaken in The Grenlandsfjords water column, where the slopes were higher than 1 for PCDD/Fs, and the K(OC) were much higher than the K(OW). One explanation may be that the influence of POPs adsorption to soots decrease because competitive sorption by other compounds in the sediment are higher than in the water column. This indicates that the sorption isotherms for these POPs need better understanding in order to be applicable in both the water column and the porewater.     

皂土对CuCl2的吸附性能

研究了CuCl2在荷结构负电荷皂土上的吸附性能,考察了pH、无机以及有机添加剂等因素的影响,并结合IR和XRD实验结果探讨了吸附机理。研究表明,皂土对CuCl2有很强的吸附能力,其吸附动力学和吸附等温线分别符合准二级速率方程和Langmuir方程。初始pH增大,吸附量增加。无机以及有机添加剂均能能明显抑制吸附。Cu2+在皂土上的吸附层在微观上可分为因化学键合作用而形成的内络合层和因静电作用而形成的外络合层。     

皂土对CuCl_2的吸附性能

研究了CuCl2在荷结构负电荷皂土上的吸附性能,考察了pH、无机以及有机添加剂等因素的影响,并结合IR和XRD实验结果探讨了吸附机理。研究表明,皂土对CuCl2有很强的吸附能力,其吸附动力学和吸附等温线分别符合准二级速率方程和Langmuir方程。初始pH增大,吸附量增加。无机以及有机添加剂均能能明显抑制吸附。Cu2＋在皂土上的吸附层在微观上可分为因化学键合作用而形成的内络合层和因静电作用而形成的外络合层。     

Adsorption of phenol by bentonite

The potential of bentonite for phenol adsorption from aqueous solutions was studied. Batch kinetics and isotherm studies were carried out to evaluate the effect of contact time, initial concentration, pH, presence of solvent, and the desorption characteristics of bentonite. The adsorption of phenol increases with increasing initial phenol concentration and decreases with increasing the solution pH value. The adsorption process was significantly influenced by the solvent type in which phenol was dissolved. The affinity of phenol to bentonite in the presence of cyclohexane was greater than that in water and was lowest in the presence of methanol. Methanol was used to extract phenol from bentonite. The degree of extraction was dependent on the amount of phenol adsorbed by bentonite. X-ray diffraction analysis showed that the crystalline structure of bentonite was destroyed when cyclohexane was used. The ability of bentonite to adsorb phenol from cyclohexane decreased as the water to cyclohexane ratio was increased. Furthermore, hysteresis was observed in phenol desorption from bentonite in aqueous solutions. The equilibrium data in aqueous solutions was well represented by the Langmuir and Freundlich isotherm models. The removal of phenol from aqueous solutions was observed without surface modification.     

Surface charge and adsorption from water onto quartz sand of humic acid

The surface charge of humic acid under different conditions of ionic strength, pH, and the presence of various cationic ions (Cu(2+), Zn(2+), Ba(2+), and Ca(2+)) was determined by a titration method using a cationic polyelectrolyte as titrant. Adsorption isotherms in batch experiments of the polymer from water onto quartz sand were determined at 20 degrees C, 40 degrees C, and 60 degrees C and under different conditions of ionic strength, pH, and the presence of various cationic ions (Cu(2+), Zn(2+), Ba(2+), and Ca(2+)). The data indicate significant decrease of humic acid surface charge by decreasing the pH value from 10.0 to 4.1. Similar decrease of humic acid surface charge was observed by increasing either the ionic strength or the affinity of the divalent cation toward the humic acid. At ambient temperature the adsorption of humic acid on the quartz sand seems to be controlled mainly by electrical interaction between the organic particle and the solid substrate. A correlation is found between the surface charge and the adsorbed amount of the polymer, the adsorbed amount increases when the surface charge of humic acid decreases. The increase of the adsorbed amount with the temperature suggests that adsorption process is endothermic.     

Studies on the sorption and desorption characteristics of Zn(II) on the surface soils of nuclear power plant sites in India using a radiotracer technique

Zinc adsorption was studied in the soils of three nuclear power plant sites of India. 65Zn was used as a radiotracer to study the sorption characteristics of Zn(II). The sorption of zinc was determined at 25 and 45 degrees C at pH 7.8+/-0.2 in the solution of 0.01 M Ca(NO3)2 as supporting electrolyte. The sorption data was tested both in Freundlich and Langmuir isotherms and could be described satisfactorily. The effect of organic matter and other physico-chemical properties on the uptake of zinc was also studied in all the soil samples. The results showed that the cation exchange capacity, organic matter, pH and clay content were the main contributors to zinc sorption in these soils. The adsorption maximum was found to be higher in the soil on Kakarpara Atomic Power Plant sites soils having high organic matter and clay content. The zinc supply parameters of the soils are also discussed. In the desorption studies, the sequential extraction of the adsorbed zinc from soils showed that the diethylene triamine penta acetic acid extracted maximum amount of adsorbed zinc than CaCl2 and Mg(NO3)2. The zinc sorption on the soil and amount of zinc retention after extractants desorption shows a positively correlation with vermiculite and smectite mineral content present in the clay fraction of the soil. The amount desorbed by strong base (NaOH) and demineralised water was almost negligible from soils of all the sites, whereas the desorption by strong acid (HNO3) was 75-96% of the adsorbed zinc.     

Removal of a cationic dye from aqueous solutions by adsorption onto bentonite clay

The ability of bentonite to remove malachite green from aqueous solutions has been studied for different adsorbate concentrations by varying the amount of adsorbent, temperature, pH and shaking time. Maximum adsorption of the dye, i.e. >90% has been achieved in aqueous solutions using 0.05 g of bentonite at a pH of 9. Thermodynamic parameters such as ΔH°, ΔS° and ΔG° were calculated from the slope and intercept of the linear plots of ln K_D against 1/T. Analysis of adsorption results obtained at 298, 308, 318 and 328 K showed that the adsorption pattern on bentonite seems to follow the Langmuir, Freundlih and D–R isotherms. The temperature increase reduces adsorption capacity by bentonite, due to the enhancement of the desorption step in the mechanism. The numerical values of sorption free energy (E_a) of 1.00–1.12 kJ mol⁻¹ indicated physical adsorption. The kinetic data indicated an intraparticle diffusion process with sorption being first order. The rate constant k was 0.526 min⁻¹. The concentration of malachite green oxalate was measured before and after adsorption by using UV–Vis spectrophotometer.     

Sorptive behavior of the phenylamide fungicides,mefenoxam and metalaxyl,and their acid metabolite in typical Cameroonian and German soils

Laboratory soil sorption experiments were conducted on mefenoxam, formulated metalaxyl (F-metalaxyl), pure metalaxyl (P-metalaxyl) and metalaxyl acid metabolite to elucidate differences in their sorptive behaviour on typical Cameroonian forest soil (sand clay loam, pH 4.8 and 3.01% OC) and German soil (sandy loam, pH 7.2, 1.69% OC) using a batch equilibrium method. The data obtained on all test chemicals conformed to linear and Freundlich adsorption isotherms. The Langmuir equation failed to describe the sorption of the substances tested. All substances were adsorbed to a greater extent by the Cameroonian soil. The average percentage adsorptions for mefenoxam, F-metalaxyl, P-metalaxyl and the acid metabolite on the Cameroonian soil were 27.8%, 28.3%, 31.8% and 46.8% respectively while for the German soil they were 21.7%, 21.5%, 24.7% and 9.8% respectively. The KD and KF parameters and the Freundlich exponential term (1/n) were low, indicating that the interactions between soil particles and the fungicides were weak. The sorption parameters were lower in the German soil. P-metalaxyl exhibited a higher adsorption capacity than F-metalaxyl in both soils. Mefenoxam and F-metalaxyl exhibited similar sorption parameters in soils, whereas those of P-metalaxyl and acid metabolite differed. Differences observed in the adsorption between the two soils could be attributed to their properties. Desorption studies revealed that the adsorbed fungicides were not firmly retained by soil particles and their adsorption was reversible. Desorption of adsorbed mefenoxam, P-metalaxyl and of the acid metabolite from German soil was almost completely reversible with percentage desorption rates of more than 91.0%, whereas the rate for F-metalaxyl was 74.1%. All compounds exhibited some resistance to desorption from the Cameroonian soil, with percentage desorption rates less than 77.0%. Therefore if degradation in the soil is slow the fungicides described have a potential to leach to lower soil horizons.     

Removal and Destruction of Organic Contaminants in Water Using Adsorption,Steam Regeneration,and Photocatalytic Oxidation: A Pilot-Scale Study

ABSTRACT

The overall objective of this pilot-scale study is to investigate the technical feasibility of the removal and destruction of organic contaminants in water using adsorption and photocatalytic oxidation. The process consists of two consecutive operational steps: (1) removal of organic contaminants using fixed-bed adsorption; and (2) regeneration of spent adsorbent using photocatalysis or steam, followed by decontamination of steam condensate using photocatalysis. The pilot-scale study was conducted to evaluate these options at a water treatment plant in Wausau (Wisconsin) for treatment of groundwater contaminated with tetrachloroethene (PCE), trichloroethene (TCE), cis-dichloroethene (cis-DCE), toluene, ethylbenzene (EB), and xylenes. The adsorbents used were F-400 GAC and Ambersorb 563.

In the first treatment strategy, the adsorbents were impregnated with photocatalyst and used for the removal of aqueous organics. The spent adsorbents were then exposed to ultraviolet light to achieve photocatalytic regeneration. Regeneration of adsorbents using photocatalysis was observed to be not effective, probably because the impregnated photocatalyst was fouled by background organic matter present in the groundwater matrix.

In the second treatment strategy, the spent adsorbents were regenerated using steam, followed by cleanup of steam condensate using photocatalysis. Four cycles of adsorption and three cycles of steam regeneration were performed. Ambersorb 563 adsorbent was successfully regenerated using saturated steam at 160 °C within 20 hours. The steam condensate was treated using fixed-bed photo-catalysis using 1% Pt-TiO₂ photocatalyst supported on silica gel. After 35 minutes of empty bed contact time, more than 95% removal of TCE, cis-DCE, toluene, EB, and xylenes was achieved, and more than 75% removal of PCE was observed.

In the case of activated carbon adsorbent, steam regeneration was not effective, and a significant loss in adsorbent capacity was observed.     

表面活性剂在北京碱性土壤中的吸附行为研究

通过静态吸附实验,研究了北京碱性土壤对阴离子表面活性剂SDS、阳离子表面活性剂CTAB和非离子表面活性剂Tween80的吸附行为,考察了温度对表面活性剂吸附的影响.结果表明:7种不同土样对SDS、CTAB和Tween80的吸附等温线均较好地符合Langmuir吸附模式,其吸附能力的大小顺序为2号轻壤土》轻粘土》中壤土》砂壤土》5号轻壤土》重壤土》紧砂土,这主要是由于7种土样的pH、有机质含量和机械组成不同的缘故;同一土壤中,CTAB的吸附量》Tween80的吸附量》SDS的吸附量;温度的升高,不利于SDS和CTAB在土壤中的吸附,而有利于Tween80的吸附.     

Adsorption characteristics of Ni(II) on gamma-type alumina particles and its determination of overall adsorption rate by a differential bed reactor

The adsorption experiment of nickel ion [Ni(II)] on gamma-type alumina by a differential bed reactor in aqueous solutions was investigated to determine the adsorption characteristics and overall adsorption rate. The adsorbed amount increased rapidly with pH from pH 2 to 6 and kept constant over pH 6. The adsorbed amount of Ni(II) increased with temperature from 20 to 50 degrees C. Correlation coefficients (R2) of Langmuir and Freundlich adsorption isotherms were 0.9268 and 0.9489, respectively, and Freundlich isotherm was more suitable for adsorption on gamma-type alumina than Langmuir isotherm.The overall adsorption rate of Ni(II) on gamma-type alumina at pH 6 by a differential bed rector was determined as follows: r = 68.77Ce(1.61) - 17.60qe(0.36). Al(III) ions in solutions were away from the alumina surface during the adsorption of Ni(II) and Al(III) concentration increased with an increasing Ni(II) adsorbed amount on alumina.     

Modified SBA-15 mesoporous silica for heavy metal ions remediation

N-Propylsalicylaldimino-functionalized SBA-15 mesoporous silica was prepared, characterized and used as an adsorbent for heavy metal ions. The organic-inorganic hybrid material was obtained using successive grafting procedures of SBA-15 silica with 3-aminopropyl-triethoxysilane and salicylaldehyde, respectively. For comparison an amorphous silica gel was functionalized using the same procedure. The structure and physicochemical properties of the materials were characterized by means of elemental analysis, X-ray diffraction (XRD), nitrogen adsorption-desorption, thermogravimetric analysis and FTIR spectroscopy. The organic functional groups were successfully grafted on the SBA-15 surfaces and the ordering of the support was not affected by the chemical modification. The behavior of the grafted solids for the adsorption of heavy metals ions from aqueous solutions was investigated. The hybrid materials showed high adsorption capacity and high selectivity for copper ions. Other ions, such as nickel, zinc, and cobalt were adsorbed by the modified SBA-15 material. The adsorbent can be regenerated by acid treatment without altering its properties.     

Enhancement of copper and cadmium adsorption on kaolin by the presence of humic acids

The competitive adsorption equilibrium isotherms of Cu²⁺ and Cd²⁺ on kaolin have been measured at 298 K, in the presence and the absence of humic acids (HAs). HAs were found to enhance the metal adsorption capacity of mineral surfaces, in particular kaolin. This enhancement was also observed in the competitive adsorption of copper and cadmium on kaolin and kaolin–HA complex. This competitive adsorption shows that the presence of Cd²⁺ has not an important effect on Cu²⁺ adsorption, whereas a dramatic decrease is observed on the adsorption of Cd²⁺ in the presence of Cu²⁺. The Freundlich isotherm equation was found to provide an excellent fit to the experimental data. These results were compared with the independent adsorption of both heavy metals.     

Equilibrium partitioning theory to predict the sediment toxicity of the anionic surfactant C(12)-2-LAS to Corophium volutator

The study of the effect of the sorption of linear alkylbenzene sulfonates (LAS) on the bioavailability to marine benthic organisms is essential to refine the environmental risk assessment of these compounds. According to the equilibrium partitioning theory (EqP), the effect concentration in water-only exposure will be similar to the effect concentration in the sediment pore water. In this work, sorption and desorption experiments with two marine sediments were carried out using the compound C₁₂-2-LAS. The effect of the sediment sorption on the toxicity of benthic organisms was studied in water-only and in sediment bioassays with the marine mud shrimp Corophium volutator. In addition, three common spiking methods were tested for its application in the toxicity tests, as well as the stability of the surfactant during the water-only and sediment-water test duration. LC50 values obtained from water-only exposure showed a good correspondence with the pore water concentrations calculated from the sorption and desorption isotherms in the spiked sediments.     

Effects of compositional heterogeneity and nanoporosity of raw and treated biomass-generated soot on adsorption and absorption of organic contaminants

A biomass-generated soot was sequentially treated by HCl-HF solution, organic solvent, and oxidative acid to remove ash, extractable native organic matter (EOM), and amorphous carbon. The compositional heterogeneity and nano-structure of the untreated and treated soot samples were characterized by elemental analysis, thermal gravimetric analysis, BET-N₂ surface area, and electron microscopic analysis. Sorption properties of polar and nonpolar organic pollutants onto the soot samples were compared, and individual contributions of adsorption and absorption were quantified. The sorption isotherms for raw sample were practically linear, while were nonlinear for the pretreated-soot. The removal of EOM enhanced adsorption and reduced absorption, indicating that EOM served as a partitioning phase and simultaneously masked the adsorptive sites. By drastic-oxidation, the outer amorphous carbon and the inner disordered core of the soot particles were completely removed, and a fullerene-like nanoporous structure (aromatic shell) was created, which promoted additional π-π interaction between phenanthrene and the soot.     

Adsorption of simazine on zeolite H-Y and sol–gel technique manufactured porous silica: A comparative study in model and natural waters

In this work, we studied the removal of simazine from both a model and well water by adsorption on two different adsorbents: zeolite H-Y and a porous silica made in the laboratory by using the sol–gel technique. The pH dependence of the adsorption process and the isotherms and pseudo-isotherms of adsorption were studied. Moreover, an iterative process of simazine removal from both the model and well water, which allowed us to bring the residual simazine concentration below the maximum concentration (0.05 mg L^?1) of agrochemicals in wastewater to be released in surface waters or in sink allowed by Italian laws, was proposed. The results obtained were very interesting and the conclusions drawn from them partly differed from what could reasonably be expected.     

Suitability of dye-clay complexes for removal of non-ionic organic compounds from aqueous solutions

Aqueous sorption of phenol, atrazine and naphthalene was measured on complexes formed from Na-montmorillonite (Fischer bentonite) and the organic cationic dyes crystal violet and rhodamine-B. Sorption isotherms were found to be non-linear. This agrees well with the rigid nature of the dye-clay organic coverage, which provides a finite surface for adsorption. High values of organic carbon-normalized distribution coefficients reached 20,000-25,000 for atrazine on rhodamine-B-montmorillonite, 7000 for atrazine on crystal violet-montmorillonite, and 1500 for phenol on crystal violet-montmorillonite. As such, dye-clays may significantly extend the variety of organoclay sorbents that effectively reduce aqueous concentrations of non-ionic organic compounds.     

Enhancement of phenanthrene adsorption on a clayey soil and clay minerals by coexisting lead or cadmium

Phenanthrene is commonly present together with heavy metals at many contaminated sites. This study investigated the influence of coexisting lead (Pb²⁺) or cadmium (Cd²⁺) on phenanthrene adsorption on soils. Batch experiments were conducted under different geochemical conditions including pH, mineral structure, organic matter content, and varying amounts of heavy metals. The results showed that the presence of heavy metals in solution at a fixed pH of 5.8 ± 0.1 enhanced phenanthrene adsorption, the extent of which was closely related to the concentrations and the electro-negativity of the metals. The enhancement on phenanthrene adsorption was positively correlated to the amount of adsorbed metals. Although Cd²⁺ is a softer Lewis acid, Pb²⁺ displayed a more significant effect as it was adsorbed to a greater extent on the soil surfaces. Thus, density of cation accumulation appears to be more influential than metal softness in enhancing phenanthrene adsorption. Moreover, with a portion of organic matter removed by heating at 550 °C, there was a stronger enhancement of phenanthrene adsorption by coexisting Pb²⁺, indicating an increasingly dominant mechanisms associated with Pb²⁺ at a lower organic matter content. Similar enhancement phenomenon was observed on bentonite and kaolinite, probably resulting from the cation-π bonding between the adsorbed soft metal cations and the aromatic ring of phenanthrene in solution. The desorption experiments further suggested that the bonding of phenanthrene adsorption was strengthened in the presence of Pb²⁺ and that a larger proportion of adsorbed phenanthrene remained on the soils (residual fraction) even after sequential methanol extractions. Further spectroscopic analyses and surface characterization are required to provide direct evidence of the formation and relative significance of cation-π bond for phenanthrene adsorption.     

Study on fractions of adsorbed Pb and Cd onto natural surface coatings

The speciation and extent of migration of adsorbed Pb and Cd in natural surface coatings (NSCs) were investigated using sequential extraction procedure to provide an understanding of distribution of the adsorbed Pb and Cd. Extractions were conducted on NSCs before and after Pb and Cd adsorption treatment under controlled laboratory conditions with initial Pb and Cd concentrations ranging from 0.2-2.5 mol/l. The Langmuir adsorption isotherms were applied to estimate equilibrium coefficients of Pb and Cd adsorption to NSCs components. The results showed that 58.50% of adsorbed Pb in average existed in tightly adsorbed form, and the remaining Pb was mostly present as solid oxides/hydroxides (34.00%) and exchangeable and soluble form (7.50%) in NSCs, respectively. Large amount of adsorbed Cd (70.51% in average) was present in exchangeable and soluble form, following a decreasing order in tightly adsorbed form (18.61%), solid oxides/hydroxides (9.87%), and easily oxidizable solids/compounds (1.01%), respectively. No Cd was found in strongly held oxides and precipitates. Compared to the distribution of adsorbed Pb in NSCs, Cd distribution showed that less migration of Cd from exchangeable and soluble form to solid oxides/hydroxides after adsorbed to NSCs, indicating fewer sites for Cd to adsorb to NSCs and less affinity of Cd to the NSCs. These percent distributions of metals provided an additional interpretation to that Pb adsorption to the NSCs greater than that of Cd, less retention of Cd than that of Pb and less roles attributed for Pb/Cd adsorption by organic materials in NSCs, which were observed based on the selective extraction techniques in the independent investigations.