Application of response surface methodology for the optimization of biodiesel production from yellow mustard (Sinapis alba L.) seed oil

In the present study, response surface methodology (RSM) involving central composite design (CCD) was applied to optimize the reaction parameters of biodiesel production from yellow mustard (Sinapis alba L.) seed oil during the single-step transesterification process. A total of 30 experiments were designed and performed to determine under the effects of variables on the biodiesel yield such as methanol to oil molar ratio (2:1–10:1), catalyst concentration (0.2–1.0 wt.% NaOH), reaction temperature (50–70°C), and reaction time (30–90 min). The second order polynomial model was used to predict the biodiesel yield and coefficient of determination (R²) was found to be at 0.9818. The optimum biodiesel yield was calculated as 96.695% from the model with the following reaction conditions: 7.41:1 of methanol to oil molar ratio, 0.63 wt. % NaOH of catalyst concentration, 61.84°C of reaction temperature, and 62.12 min of reaction time. It is seen that the regression model results were in agreement with the experimental data. The results showed that RSM is a suitable statistical technique for optimizing the reaction parameters in the transesterification process in order to maximize the biodiesel yield.     

Nanocatalyzed biodiesel synthesis from the oily contents of Marine brown alga Dictyota dichotoma

This research article demonstrates biodiesel synthesis through the methanolysis of the oily contents (4.02 ± 0.27% w/w on dried basis) of Dictyota dichotoma collected from the coast of Hawksbay, Pakistan. The metal oxides (CaO, MgO, ZnO, and TiO₂) used as nanocatalysts were refluxed (5% K₂SO₄), calcinated (850 °C) and characterized by Atomic Force Microscopy (AFM) which produced 93.2% w/w FAME (biodiesel) at relatively mild condition (5% catalyst, 65 °C, 3 h, 18:1 molar ratio) using CaO. Whereas, MgO, ZnO, and TiO₂ produced 92.4%, 72.5%, and 31.8% w/w FAME, respectively at elevated condition (225 °C). Thus, CaO was considered to be the best catalyst among the others. This tri-phase reaction require continuous fast mixing and the yield depends on the reaction parameters like catalyst amount, temperature, reaction time and molar ratio (methanol: oil). The reusability of these heterogeneous catalysts simplified the purification step, reduced the waste generation and make the final product technically and economically viable.     

Experimental evaluation of the catalytic efficiency of calcium based natural and modified catalyst for biodiesel synthesis

Transesterification of a mixture of vegetable oils with methanol using metal oxide catalysts derived from snail shell (SS) for biodiesel production was investigated. The metal oxides obtained from calcined snail shells in the temperature range of 650°–950 °C and modified by loading different potassium salts were used as a catalyst in the process. The catalysts were characterized by FT-IR, XRD, SEM-EDS, XPS and TGA. Catalytic activities of developed catalysts were also tested by Hammet indicator method and ion exchange method. The best calcination conditions were observed at 850°C for 4 hours based on biodiesel yield. The KF loaded snail shell gave highest biodiesel yield of 98 ± 1% in a batch reactor with highest basicity (15.9 mmoles/g) and basic strength measured by Hammet method. The optimized reaction conditions were: reaction temperature 65°C, reaction time 3 hours, methanol to oil molar ratio 9:1 and catalyst concentration 3wt%. Leaching and reusability tests confirm the stability of the catalyst as it encounters only 3% of leaching and small changes in catalytic activity up to five runs in terms of biodiesel yield.     

Effect of calcination temperature on the application of sodium zirconate solid base catalyst for biodiesel production from Jatropha curcas oil

Influence of catalyst calcination temperature on the catalyst characteristics and catalytic transesterification of Jatropha curcas oil for biodiesel production was studied by using sodium zirconate (Na₂ZrO₃) solid base catalyst. Na₂ZrO₃ catalysts were prepared by impregnation method followed by calcination at temperatures of 700, 800, and 900°C. The prepared catalysts were characterized by X-ray diffraction analysis, Fourier transform infrared spectroscopy, and field emission scanning electron microscopy. Important parameters influencing the catalytic activity and fatty acid methyl ester yield were investigated. It was found that the increase in calcination temperature showed marked increase in activity due to the increased porosity and presence of tetragonal zirconia. Investigation of the reusability of the catalysts showed that the catalytic activity was retained even after five cycles of reaction.     

Production and characterization of biodiesel from Eriobotrya Japonica seed oil: an optimization study

Biodiesel is now-a-days recognized as a real potential alternative to petroleum-derived diesel fuel due to its number of desirable characteristics. However, its higher production cost resulting mainly due to use of costly food-grade vegetable oils as raw materials is the major barrier to its economic viability. Present work is an attempt to explore the potential of Eriobotrya japonica seed oil for the synthesis of biodiesel using alkali-catalyzed transesterification. Optimization of production parameters, namely molar ratio of alcohol to oil, amount of catalyst, reaction time and temperature, was carried out using Taguchi method. Fatty acid composition of both oil and biodiesel was determined using GC and H¹ NMR. Alcohol to oil molar ratio of 6:1, catalyst amount of 1% wt/wt, 2 h reaction time and 50 ^°C reaction temperature were found to be the optimum conditions for obtaining 94.52% biodiesel. Highest % contribution was shown by the ‘amount of catalyst’ (67.32%) followed by molar ratio of alcohol to oil (25.51%). Major fuel properties of E. japonica methyl esters produced under optimum conditions were found within the specified limits of ASTM D6751 for biodiesel, hence it may be considered a prospective substitute of petro-diesel.     

Scleropyrum pentandrum (Dennst.) mabb—oil as a feedstock for biodiesel production—engine performance and emission studies

A feasibility study on utilization of non edible oil of Scleropyrum pentandrum was carried out to see its potential as a new source for biodiesel production. Nonedible oil seeds of Scleropyrum pentandrum have oil content of 55–60%. Transesterification of freshly extracted oil in the presence of anhydrous sodium hydroxide at a concentration 1% (w/v oil) and methanol-oil ratio of 40% (v/v oil) yields 90.8% methyl esters under conventional heating. Month old oil requires sulfuric acid pretreatment (esterification) before transesterification. The transesterified oil has a density 889–893 kg/m³; kinematic viscosity of 4.21–5.7 mm²/s; cetane index 46.03; pour point of ?15°C and gross calorific value of 40.135 MJ/kg and oxidative stability of 2.35 hours. The properties are well within the Indian, European and American standard limits recommended for biodiesel except the oxidation stability, which can be improved by adding antioxidant additives. The engine performance studies of B10 and B20 blends of Scleropyrum pentandrum biodiesel (SP biodiesel) with statistical inference confirmed that it can be used as a fuel in CI engines without any engine modifications. The engine exhaust emission analysis showed that the emission of hydrocarbons can be minimized by at least 15–20%, CO emission by 15%, smoke opacity by 10–12% and moderately lesser CO₂ and NOx emissions.     

Optimization of biodiesel production from waste cooking oil using ion-exchange resins

Waste cooking oil is a potential substitution of refined vegetable oil for the production of biodiesel due to the low cost of raw material and for solving their disposal problem. In this study, optimization of esterification process of free fatty acids in artificially acidified soybean oil with oleic acid has been carried out using methanol as an agent and ion exchange resin as a heterogeneous catalyst. The esterification reaction has been investigated based on the mass balance of the developed model. The model has been validated against experimental data and effects of temperature and catalyst weight have been analyzed. Thereafter, optimization process has been fulfilled for two different objective functions as conversion of acid oil and benefit. Optimization results indicated that the maximum conversion of acid is 95.95%, which is achievable at 4.48-g catalyst loading and reaction temperature of 120°C. Maximum benefit was obtained as US$0.057 per batch of reaction at a catalyst amount of 1 g and temperature of 120°C.     

Homogeneous catalysed biodiesel synthesis from Alexandrian Laurel (Calophyllum inophyllum L.) kernel oil using ortho-phosphoric acid as a pretreatment catalyst

In this study, a non-edible seed oil of Alexandrian Laurel (Calophyllum inophyllum L.) with higher free fatty acid content has been harnessed to produce biodiesel by transesterification process. The 20.2% free fatty acid (FFA) content was first reduced to 12.9% by using TOP degumming process. Ortho-phosphoric acid was used to esterify the refined kernel oil. Transesterification reaction was performed with NaOH as an alkaline catalyst and methanol as an analytical solvent. The effects of methanol to oil molar ratio (MR), catalyst concentration (CC), reaction temperature (TP), reaction time (TM), and stirrer speed (SS) on biodiesel conversion were studied to optimize the transesterification conditions using DOE- approach. The experimental study revealed that 9:1 MR, 0.8 wt.% CC, 60°C TP, 75 min TM and 1000 rpm SS were the optimal process control variables. The study indicated that CC was the most important control parameter in optimal methyl ester production. The optimal treatment combination yielded 97.14% of biodiesel. The profile of biodiesel was determined using gas chromatography-mass spectrometry. ¹H NMR spectrum of Calophyllum inophyllum methyl ester (CIME) has been reported. The properties of the biodiesel have been found within specifications of the ASTM D6751 and EN 14214 standards and hence could be considered as a suitable alternative to diesel fuel for sustainable circulation of carbon.     

Assessment of biomass and lipid productivity and biodiesel quality of an indigenous microalga Chlorella sorokiniana MIC-G5

Generation of biodiesel from microalgae has been extensively investigated; however, its quality is often not suitable for use as fuel. Our investigation involved the evaluation of biodiesel quality using a native isolate Chlorella sorokiniana MIC-G5, as specified by American Society for Testing and Materials (ASTM), after transesterification of lipids with methanol, in the presence of sodium methoxide. Total quantity of lipids extracted from dry biomass, of approximately 410–450 mg g^?1 was characterized using FTIR and ¹H NMR. After transesterification, the total saturated and unsaturated fatty acid methyl esters (FAMEs) were 43% and 57%, respectively. The major FAMEs present in the biodiesel were methyl palmitate (C16:0), methyl oleate (C18:1), and methyl linoleate (C18:2), and the ¹H NMR spectra matched with criteria prescribed for high-quality biodiesel. The biodiesel exhibited a density of 0.873 g cm^–3, viscosity of 3.418 mm² s^?1, cetane number (CN) of 57.85, high heating value (HHV) of 40.25, iodine value of 71.823 g I₂ 100 g^?1, degree of unsaturation (DU) of 58%, and a cold filter plugging point (CFPP) of –5.22°C. Critical fuel parameters, including oxidation stability, CN, HHV, iodine value, flash point, cloud point, pour point, density, and viscosity were in accordance with the methyl ester composition and structural configuration. Hence, C. sorokiniana can be a promising feedstock for biodiesel generation.     

Application of TiO2 nanoparticles for eco-friendly biodiesel production from waste olive oil

An environmentally benign, simple, and efficient process has been developed for biodiesel production from waste olive oil in the presence of a catalytic amount of TiO₂ nanoparticles at 120°C with a conversion of 91.2% within 4 h. The present method affords nontoxic and noncorrosive medium, high yield of biodiesel, clean reaction, and simple experimental and isolation procedures. The catalyst can be recycled by simple filtration and reused without any significant reduction in its activity.     

Possibility of converting indigenous Salvadora persica L. seed oil into biodiesel in Pakistan

In this research study, biodiesel has been successfully produced from vegetable seed oil of an indigenous plant Salvadora persica L. that meets the international biodiesel standard (ASTM D6751). The biodiesel yield was 1.57 g/5 g (31.4% by weight) and the in-situ transesterification ester content conversion was 97.7%. The produced biodiesel density was 0.894 g/mL, its kinematic viscosity 5.51 mm²/s, HHV 35.26 MJ/kg, flash point 210°C, cetane no. 61, and sulfur content 0.0844%. Thermal analysis of the biodiesel showed that 97% weight loss was achieved at 595°C with total oxidation of the biodiesel. The production energy efficiency was 0.46% with a lab scale setup, assuming the volume fraction ratio (volume of the sample/total volume of the equipment used). The results revealed that single-step in-situ transesterification method is suitable for the production of biodiesel from S. persica seed oil.     

Ferric-manganese doped sulphated zirconia nanoparticles catalyst for single-step biodiesel production from waste cooking oil: Characterization and optimization

Biodiesel of waste cooking oil origin is gaining attention as a replacement for current fossil fuels, as its low-priced, recycled feedstock shall prevent food source competition, which is estimated to happen with current biodiesel production processes. As a result, waste cooking oil has been claimed to be a highly potential feedstock for biodiesel production. In the present research work, Fe-Mn doped sulphated zirconia catalyst was synthesized and used in simultaneous esterification and transesterification of waste cooking oil to biodiesel synthesis. The catalyst was prepared through the impregnation method and characterized by using XRD, TPD-NH_3, FT-IR, BET, and TEM. Response surface methodology (RSM) in conjunction with the central composite design (CCD) was applied to statistically evaluate and optimize the biodiesel preparation process. It was found that the synthesis of biodiesel achieved an optimum level of 97.2% waste cooking oil methyl ester’s (WCOME’s) yield at the following reaction conditions: methanol/oil molar ratio: 10:1, catalyst concentration: 3.0 wt %, and reaction temperature: 160 °C. The extremely high WCOME’s yield of 97.2% was proved to be due to high acidity, surface area, and large pore diameter; reactants can easily diffuse into the interior pore of the catalyst and allow them to be in contact with active sites that enhance catalytic activity.     

Preparation of jet engine range fuel from biomass pyrolysis oil through hydrogenation and its comparison with aviation kerosene

The Bio-oil was produced from the pyrolysis of agricultural wastes (Eucalyptus sawdust) and discarded soybean frying oil. The temperature of the pyrolysis system was initiated at 28°C and increased to 850°C. Atmospheric distillation of crude bio-oil was performed and a fraction at a temperature range 160–240°C (pyrolysis oil) was separated and subjected to GC-MS, ¹H-NMR, TGA and FTIR analysis to identify the different properties and compounds present in pyrolysis oil. It was noticed that there was an abundance of oxygen and nitrogen containing compounds as well as other reactive species in pyrolysis oil. To reduce the amount of these species, the pyrolysis oil was subjected to hydrogenation in the presence of NiMo as a catalyst. After hydrogenation, the atmospheric distillation of hydrogenated bio-oil was performed and another fraction at temperature range 160–240°C (hydrogenated bio-oil) was separated and analyzed by the same techniques. It was noticed that during hydrogenation, more than 60% oxygenated and other reactive species were converted into hydrocarbons. Hydrogenated bio-oil showed very similar physico-chemical properties such as distillation curve, density, viscosity, freezing point, flash point, the presence of hydrocarbons and enthalpy of combustion as aviation kerosene also known as QAV-1.     

Promotional effect of transition metal doping on the properties of KF/CaO catalyst for biodiesel synthesis

A series of heterogeneous KF/CaO catalysts modified with transition metals (lanthanum, cerium, and zirconium) were prepared via wet impregnation method and applied to the trsansesterification process of waste cooking oil (WCO) as feedstock with methanol to biodiesel production. The structure, performance of the solid catalysts was characterized by X-ray diffraction (XRD), temperature programmed desorption of CO₂ (CO₂-TPD), scanning electron microscopy (SEM), and energy-dispersive spectroscopy (EDS). The effect of methanol/oil molar ratio, ¹reaction time, reaction temperature, catalyst amount, and stability was investigated. The results showed that 10 wt% of lanthanum, cerium, and zirconium improved the catalytic activity of KF/CaO catalyst. The maximum catalytic activity using the lanthanum doping of 10wt% on KF/CaO catalyst was reached 98.7% under the optimal reaction condition of methanol/oil molar ratio of 12:1, reaction for 1 h at reaction temperature of 65°C, and 4% (wt/wt oil) catalyst amount. In addition, the FAME yield of KF/CaO/La catalyst remained higher than 95% after 10 cycles. The promotional effect of lanthanum doping could be attributed to the enhancement of the basicity strength of KF/CaO catalyst and block the leach of Ca²⁺ in the transesterification reaction.     

Relationship between liquid depth and the acoustic generation of hydrogen: design aspect for large cavitational reactors with special focus on the role of the wave attenuation

Understanding the effect of the liquid depth (z) on the acoustic generation of hydrogen is highly required for designing large-scale sonoreactors for hydrogen production because acoustic cavitation is the central event that initiates sonochemical reactions. In this paper, we present a computational analysis of the liquid-depth effect on the generation of H₂ from a reactive acoustic bubble trapped in water irradiated with an attenuating sinusoidal ultrasound wave. The computations were made for different operating conditions of frequency (355–1000 kHz), acoustic intensity (1–5 W/cm²), and liquid temperature (10–30°C). The contribution of the acoustic wave attenuation on the overall effect of depth was appreciated for the different conditions. It was found that the acoustic generation of hydrogen diminished hardly with increasing depth up to z = 8 m, and the depth effect was strongly operating parameter-dependent. The sound wave attenuation played a crucial role in quenching H₂ yield, particularly at higher z. The reduction of the H₂ yield with depth was more pronounced at higher frequency (1000 kHz) and lower temperature (10°C) and acoustic intensity (1 W/cm²). The attenuation of the sound wave may contribute up to 100% in the overall reductive effect of depth toward H₂ production rate. This parameter could be imperatively included when studying all aspects of underwater acoustic cavitation.     

Production of bio-oil from algal biomass and its upgradation to biodiesel using CaO-based heterogeneous catalysts

The present article deals with the production of bio-oil from algal biomass as well as the preparation and characterization of noble CaO-based heterogeneous catalyst for upgradation of bio-oil to biodiesel. The bio-oil has been extracted from algal biomass using hexane as solvent in soxhlet apparatus and upgraded to biodiesel by transesterification using noble CaO-based heterogeneous catalysts. Catalyst with TiO₂:CaO molar ratio of 0.25 and calcination temperature of 700°C has been found to be most suitable among all the catalysts developed. Characterization of the catalysts has been done by using X-ray diffraction (XRD), scanning electron microscope (SEM), and thermo-gravimetric analysis (TGA). The input--output model has been developed to correlate experimental and predicted value of biodiesel yield. Optimization of process parameters has been done using response surface methodology. Various properties and elemental composition of algal bio-oil and biodiesel have been determined and compared with biodiesel.     

Biodiesel production from a free fatty acid containing Karanja oil by a single-step heterogeneously catalyzed process

Karanja oil, containing 6.2% free fatty acids (FFAs), was considered for biodiesel production using a single-step solid-phase acid catalyzed process. Different types of zeolites and Amberlyst15 catalysts were tested and biodiesel was produced. Under similar conditions, the highest biodiesel yield was achieved using an Amberlyst15 catalyst, which contained 3–5% of moisture. The effects of operating parameters of the reaction such as reaction temperature, catalyst amount, and methanol-to-oil ratio were studied. An increase of methanol:oil ratio revealed a non-monotonic increase in biodiesel yields. Similar non-monotonic behavior was observed when Jatropha oil was used. Leaching and catalyst reusability were also considered. No significant effects of leaching were observed and catalyst reusability appeared to be affected by methanol interactions. The presence of a co-solvent, Tetrahydrofuran (THF), increased the biodiesel yield. Furthermore, an optimum amount of THF (THF:methanol volume ratio of 1:2) gave rise to the highest biodiesel yield. A biodiesel yield of 93% was achieved at 120 °C using a single-step process with Amberlyst15 as a catalyst, THF as a co-solvent, and a methanol:oil ratio of 30:1.     

What Matters Most: Are Future Stream Temperatures More Sensitive to Changing Air Temperatures,Discharge, or Riparian Vegetation?

Simulations of stream temperatures showed a wide range of future thermal regimes under a warming climate — from 2.9°C warmer to 7.6°C cooler than current conditions — depending primarily on shade from riparian vegetation. We used the stream temperature model, Heat Source, to analyze a 37‐km study segment of the upper Middle Fork John Day River, located in northeast Oregon, USA. We developed alternative future scenarios based on downscaled projections from climate change models and the composition and structure of native riparian forests. We examined 36 scenarios combining future changes in air temperature (ΔT_air = 0°C, +2°C, and +4°C), stream discharge (ΔQ = ?30%, 0%, and +30%), and riparian vegetation (post‐wildfire with 7% shade, current vegetation with 19% shade, a young‐open forest with 34% shade, and a mature riparian forest with 79% effective shade). Shade from riparian vegetation had the largest influence on stream temperatures, changing the seven‐day average daily maximum temperature (7DADM) from +1°C to ?7°C. In comparison, the 7DADM increased by 1.4°C with a 4°C increase in air temperature and by 0.7°C with a 30% change in discharge. Many streams throughout the interior western United States have been altered in ways that have substantially reduced shade. The effect of restoring shade could result in future stream temperatures that are colder than today, even under a warmer climate with substantially lower late‐summer streamflow.     

Experimental investigation on the performance and emission characteristics of a diesel engine by varying the injection pressure and injection timing using mixed biodiesel

Biodiesel is a promising fuel for compression ignition engines instead of diesel fuel. Due to the depletion of diesel fuel, an alternative fuel can be used in an engine. The experiments were conducted on a four-stroke, single cylinder CI engine. In this present investigation, an attempt has been made to study the influence of injection pressure (IP) and injection timing (IT) on the performance and emission characteristics of diesel engines by using mixed biodiesel (Thevetia peruviana, Jatropha, Pongamia, and Azadirachta indica). The injection pressure is varied from 200 to 230 bar and the injection timing is varied from 23 to 29° bTDC at an increment of 10 bar and 2° bTDC, respectively, and the results were compared with diesel. From this study, the results showed that the brake thermal efficiency (BTE) was increased by 2.4% with an increase in injection pressure and 1.5% with an increase in the injection timing for the maximum load, but lesser than diesel. Furthermore, a reduction of 5.08% of brake specific fuel consumption (BSFC) has been noticed for the rise in IP and IT with loads but higher than diesel. The reduction was 34.17%, 53.85%, and 29.7% and 29.17%, 53.85%, and 21.95% of hydrocarbons (HC), carbon monoxide (CO), and smoke emissions, respectively, at 230 bar injection pressure and at 27° bTDC injection timing. Also, a significant increase in nitrogen oxides (NO_x) and carbon dioxide (CO₂) emissions at the maximum load was observed by increasing the injection pressure and injection timing.     

Biodiesel synthesis and characterization using welted thistle plant (Carduus acanthoides) as source of new non-edible seed oil

In this work we applied base catalyzed transesterification to convert non-edible welted thistle oil (Carduus acanthoides) as new non-edible feedstock into biodiesel (Fatty acid methyl esters). The highest biodiesel yield of 88% was obtained using optimized reaction conditions of 70°C and 5:1 molar ratio (methanol:oil). The synthesized esters were characterize and confirmed by the application of NMR and FT-IR techniques. Gas chromatography and mass spectroscopy identified different fatty acids as palmatic acid (C16:0), oleic acid (C18:1), linoleic acid (18:2), arachidic acid (C20:0), eicosanic acid (C20:1), and erucic acid (C22:1) in the oil of welted thistle. Six corresponding methyl esters reported in welted thistle oil biodiesel includes 9-hexadecenoic acid, hexadecanoic acid, 9-octadecadienoic acid, 11-eicosanoic acid, eicosanoic acid and 13-docosenoicacid. Fuel properties, such as density @40°C Kg/L (0.8470), kinematic viscosity @ 40°C c St (4.37), flash point (95°C), cloud point (+4°C), pour point (?5°C), and sulfur contents (0.0112% wt) of the biodiesel produced were compatible with American Society for Testing and Materials D 6751 specifications.