Carbon materials-catalyzed hydroliquefaction of flame-retardant plastics in organic solvents

Flame-retardant plastics, such as desktop and laptop personal computer bodies, could be completely liquefied by carbon materials-catalyzed hydroliquefaction in tetralin without using H₂ as a hydrogen source. Active carbons with larger surface areas (1450–3450 m²/g) acted as superior catalysts in transferring tetralin hydrogens to plastics. On the other hand, carbon blacks and fullerene-rich soot were less active catalysts. Graphite and mesocarbon microbeads did not show any catalytic effects. Benzene, toluene, and ethylbenzene were obtained as recyclable hydrocarbons; their total amounts varied from 4 wt% to 12 wt% depending on the types of plastics and the carbon materials used. Organic bromides such as polybromodioxins were not contained in the gases and oils of the product. Received: July 19, 2000 / Accepted: September 17, 2000     

Polyethylene conversion by partial oxidation in supercritical water

This paper gives the results of partial oxidation experiments of polyethylene (PE) in supercritical water (SCW). The experiments were carried out at a reaction temperature of 693K and a reaction time of 30 min using 6 cm³ of a batch-type reactor. The loaded sample weight was 0.3 g and there was 2.52 g water (0.42 g/cm³). The ratio of oxygen atoms to carbon atoms was 0.3. The results show a significant CO formation in O₂–SCW, and the 1-alkene/n-alkane ratio in partial oxidation was higher than that in SCW pyrolysis. These results suggest the possibility of the hydrogenation of hydrocarbon through partial oxidation followed by a water–gas shift reaction. Received: July 19, 2000 / Accepted: September 28, 2000     

Hydroreforming over Ni/H-beta of the thermal cracking products of LDPE, HDPE and PP for fuel production

The thermal cracking at 400?°C of pure polyolefins—low density polyethylene (LDPE), high density polyethylene (HDPE) and polypropylene (PP) and a standard polyolefin mixture (46?% LDPE?+?27?% HDPE?+?28?% PP)—was studied together with the catalytic hydroreforming of the obtained oils over Ni/h-beta at 310?°C under 20?bar of hydrogen. The oils obtained after the thermal cracking of PP contain the highest amount of gasoline (58?%), while those coming from HDPE the lowest (39?%). The bromine index of the oils was very high, ranging from 54.1 (LDPE) to 83.8 (PP), indicating a high olefinic content of the oils. Additionally, the thermal cracking of the mixture indicates the occurrence of a synergestic effect among plastics, with transfer of methyl groups from PP to polyethylenes. Ni/h-beta (Si/Al?=?25; Ni content?=?6.2?wt%) catalyst was used in the hydroreforming since it contains a bimodal pore size distribution (0.6/3.1?nm), which improves accessibility of the oil molecules to the catalytic sites. After the hydroreforming and regardless of the plastics used, the share of lighter products (gasoline and gases) increases, reaching a remarkable 68?% of gasolines with the oils coming from PP. Regardless of the starting feed, the amount of useful fuels (gasoline?+?light diesel) was within 80–85?%. Additionally, the oils were successfully hydrogenated since the bromine indexes dropped below 7, indicating that more than 90?% of the starting olefins were saturated. The usage of catalysts increased the amount of aromatics in the obtained oils within 13–20?%, depending on the starting plastic. Likewise, the isoparaffin content of the gasolines was within 35–40?%, except for PP, where it was enhanced to 62?%. However, the research octane number (RON) of the gasolines from LDPE and PP and the cetane indexes of the diesel from all the plastics were promising for their application as fuels.     

Thermal cracking of oils from waste plastics

Thermal cracking of decomposed waste plastic oil produces a good yield of olefins. The solvent extraction of such waste plastic oil seems to be efficient for increasing gas yields and recycling monomers. To assess the potential of monomer recovery from municipal waste plastics, the oils were cracked using a laboratory-scale quartz-tube reactor. The waste plastic oils were provided by two commercial plants of the Sapporo Plastic Recycle Co. and the Dohoh Recycle Center Co. in Japan. A model waste plastic oil made in a laboratory was also examined. Yields of ethene, propene, and other products were measured at different temperatures. Two-step pyrolysis reduces coking compared with the direct thermal degradation of plastics. The raffinates from waste plastic oils extracted by sulfolane were also cracked. The primary products were almost the same as those from nontreated oils. The maximum total gas yield was 78wt%–85wt% at 750°C, an increase of about 20wt% compared with that of nonextracted oil. Solvent extraction removes stable aromatic hydrocarbons such as styrene, which is more coked than cracked.     

Behavior of bromine on the thermal decomposition of paper-based phenolic laminate wastes

We investigated the thermal properties and behavior of bromine on the thermal decomposition of paper-based phenolic laminate wastes containing polybrominated flame retardants. The thermal properties of the phenolic laminate wastes were measured with a thermogravimeter and a conduction-type scanning calorimeter (TG-CSC). The weight loss of the wastes on thermal decomposition was mainly in three phases between 40°C and 600°C. The enthalpy (ΔH) of the thermal decomposition was 104 cal/g. The material balance of the decomposition components was measured with batch-type thermal decomposition equipment. The ratios of carbon residue, liquid, and gas on decomposition at 800°C in a vacuum were 37 wt. %, 48 wt. %, and 15 wt. %, respectively. The bromine contents in the carbon residue and liquid were less than 0.02 wt. % and 10 wt. %, respectively. These results are useful both in the carbonization process of these wastes and in the application of carbon residue as carbon materials. Received: August 11, 2000 / Accepted: March 7, 2001     

Decomposition of mixed plastics consisting of polypropylene and polyethylene terephthalate into oils over titania/silica catalysts

The catalytic decomposition of mixed plastics consisting of polypropylene (PP) and polyethylene terephthalate (PET) has been investigated over titania/silica catalysts at 698 K. The yield of oil produced was about 70%, and the large amounts of C₁₈₊ hydrocarbons this contained was from the aromatics in PET. Gas was also produced, including C₃–C₅ hydrocarbons. The carbon-number fractions in the oil was influenced by the PET/(PP + PET) ratios and the catalyst weight. The titania/silica catalysts could be used repeatedly, and after they had been fouled, could be regenerated. From the Fourier Transform Infrared (FT–IR) spectroscopic data of adsorbed pyridine on the catalyst surface, most of the acid sites of the titania/silica catalysts were found to be Lewis sites where the hydride abstracted from PP pyrolysates react with PET pyrolysates to form oil and gas. Received: July 19, 2000 / Accepted: October 20, 2000     

Upgrading mixed polyolefin waste with magnetic density separation

Polyolefin fractions are often end fractions resulting from the recycling of end-of-life consumer products. Polypropylene (PP) and polyethylene (PE) are present in such fractions as a mixture. For instance, the ratio of PP and PE in car scrap is 70:30 on average. However, the grade of the PP and PE should typically be better than 97% to be reused again as a high quality product. Density separation of the different polyolefins can be a solution. A promising separation technique is the inverse magnetic density separator (IMDS). This paper discusses the potential of shredder residue, one of the possible polyolefin’s waste stream sources for the IMDS, in detail. Experiments with the separation of polyolefins with an IMDS prototype show both high grade and high recovery. The paper concludes with the economic opportunities of the IMDS in the recycling of polyolefins.     

Oxidation catalyst of iron oxide suppressing dioxin formation in polyethylene combustion

A new iron oxide catalyst, which has a superior oxidation activity in carbon monoxide and polyethylene (PE) combustion, was synthesized by an aqueous solution reaction. Catalytic oxidation of carbon monoxide over six kinds of hematite obtained from the goethite was done using a microcatalytic pulse reactor, and the composition of the hematite with the highest oxidation activity was determined. With the aim of suppressing dioxin formation on combustion, incineration tests of solid wastes in PE refuse bags with and without the goethite were carried out using a commercial semibatch-type incinerator with a combustion chamber of 6.2 m³. The result confirmed that the concentration of dioxins in the flue gas decreased considerably when the refuse was incinerated in PE bags manufactured with goethite. Received: July 24, 2000 / Accepted: October 18, 2000     

Gasification of waste plastics by steam reforming in a fluidized bed

The process of producing synthetic gas from waste plastics by steam reforming was investigated. To evaluate this process, the steam reforming of the oils derived from low-density polyethylene and polystyrene were carried out using a laboratory-scale fluidized bed of Ni-Al₂O₃ catalysts. The performance of gasification in terms of carbon conversion, gas yield, and gas compositions was examined. Although oils derived from plastics contain many kinds of heavy hydrocarbons and aromatics, they were well gasified at temperatures above 1023 K with a steam/carbon ratio of 3.5 and a weight hourly space velocity of 1 h⁻¹. The hydrogen content of the product gas was very high at approximately 72 vol% for polyethylene-derived oil and 68 vol% for polystyrene-derived oil. These compositions agreed well with the values calculated from chemical equilibrium.     

Waste plastics recycling by an entrained-flow gasifier

We studied an entrained-flow gasification process which efficiently converts waste plastics to energy at a high energy recovery rate. Waste plastics, after being shredded to <8 mm or <14 mm, were fed into an entrained-flow gasifier with air and oxygen. In the gasifier, organic substances were pyrolyzed, partially combusted, and then converted into synthetic gas (CO, H₂) at a high temperature (over 1600 K). The clarified gasification characteristics were that the lower heat value (LHV) of the product gas was over 4.2 MJ/Nm³ and the cold gas efficiency was approximately 60%. Other inert substances in the wastes such as ashes and metals were melted into slag and condensed on bag filters. The bag filters and a water scrubber removed impurities such as dusts, heavy metals, and hydrogen halides from the product gases. Solid hydrocarbons, which include char and soot, were removed at a hot cyclone and on the bag filters. Received: July 19, 2000 / Accepted: October 3, 2000     

Development of a catalytic cracking process for converting waste plastics to petrochemicals

The catalytic degradation of polyolefin using H-gallosilicates was examined using a bench-scale reactor (0.8kg/h) with semicontinuous feeding and the following plastics: (1) low-density polyethylene (LDPE) pellets; (2) linear low-density polyethylene (L-LDPE) pellets; (3) high-density polyethylene (HDPE) pellets; (4) polypropylene (PP) pellets; (5) polyolefin obtained from pulverized industrial waste plastics. The yields of liquid compounds from these materials, which were aromatics in most cases, ranged from 55wt% to 68wt%. With an increase in the ratio of total reactant to catalyst, the liquid yield remained the same. Yields of benzene, toluene, and xylenes (BTXs) decreased rapidly to below 50wt% at a ratio of more than 30. Differences in this ratio for BTXs were always small and were independent of the material. Only about half of the gas product was propane with a fresh catalyst. When the experiments were repeated, propylene, isobutane, and isobutene were found to increase.     

Study on the conversion of waste plastics/petroleum resid mixtures to transportation fuels

Catalytic coprocessing of model and waste plastics with light Arabian crude oil residue was investigated using NiMo/Al₂O₃, ZSM-5, FCC, and hydrocracking catalysts. Reaction systems that were studied included low density polyethylene (LDPE), high density polyethylene (HDPE), polystyrene (PS), and polypropylene (PP). A series of single (plastic/catalyst) and binary (plastic/resid/catalyst) reactions were carried out in a 25-cm³ micro autoclave reactor under different conditions of weight and type of catalyst, duration, pressure, and temperature. The optimum conditions selected for our work were: 1% catalyst by weight of total feedstock weight, 60min reaction time, 8.3Mpa of H₂, and 430°C. The product distribution for the binary system using plastic and petroleum residue provided some encouraging results. High yields of liquid fuels in the boiling range of 100°–480°C and gases were obtained along with a small amount of heavy oils and insoluble material such as gums and coke. In general, this study helps to demonstrate the technical feasibility of upgrading both waste plastics and petroleum resid, as well as an alternative approach to feedstock recycling.     

Influence of zinc chloride addition on the chemical structure of bio-oil obtained during co-pyrolysis of wood/synthetic polymer blends

The chemical structure of liquid products of the pinewood sawdust (W) co-pyrolysis with polystyrene (PS) and polypropylene (PP) with and without the zinc chloride as an additive was investigated. The pyrolysis process was carried out at 450 °C with the heating rate of 5 °C/min. The yield of liquid products of pyrolysis was in the range of 37–91 wt% and their form was liquid or semi-solid depending on the composition of the wood/polymer blend. The zinc chloride addition to wood/polymer blends has influenced the range of samples decomposition as well as the chemical structure of resulted bio-oils. All bio-oils from wood/polypropylene blends were two-phase (liquid and solid). Contrarily, all bio-oils obtained from biopolymer/polypropylene blends with zinc chloride added were yellow liquids. All analyses proved that the structure and the quality of bio-oil strongly depend on both the composition of the blend and the presence of ZnCl₂ as an additive. The FT-IR analyses of oils showed that oxygen-containing groups and hydrocarbons content highly depend on the composition of biomass/synthetic polymer mixture. The fractionation of bio-oils by column chromatography with four different solvents was followed by GC–MS analysis. Results confirmed the significant removal and/or transformation of oxygen-containing organic compounds due to the zinc chloride presence during pyrolysis process.     

Pore structure and adsorption properties of carbonized material prepared from waste paper

We have already reported the adsorptivity and pore structure of activated carbon made from waste newspaper in order to use the waste paper for purposes other than paper-making stock. However, manufacturing the activated carbon may not necessarily be an advantageous method based on environmental concerns and the effective use of the resource because the reaction during the activating process is endothermic and the amount of carbon consumed is significant. Here, we examine the pore structure and adsorption properties of waste newspaper used as an adsorbent in the form of a carbonized material. Waste newspaper was carbonized for 2 h in the temperature range 400°–1000°C. The specific surface area of the carbonized material obtained, 418 m²/g, was highest for the sample carbonized at 800°C, which was equal to or greater than that of commercially available charcoal. Moreover, the iodine adsorption number of 581 mg/g was the highest and the rate of adsorption was the fastest for the sample carbonized at 800°C. However, the humidity control capability was highest for the material carbonized at 600°–700°C. It has been determined that it is advantageous to carbonize waste paper at 800°C in order to use the carbonized material as an adsorbent, while carbonization at 600°–700°C is more advantageous for use as a humidity control material. Received: June 23, 2000 / Accepted: January 17, 2001     

Pyrolysis of virgin and waste polypropylene and its mixtures with waste polyethylene and polystyrene

A comparison of waste and virgin polypropylene (PP) plastics under slow pyrolysis conditions is presented. Moreover, mixtures of waste PP with wastes of polyethylene (PE) and polystyrene (PS) were pyrolyzed under the same operating conditions. Not only the impact of waste on degradation products but also impacts of the variations in the mixing ratio were investigated. The thermogravimetric weight loss curves and their derivatives of virgin and waste PP showed differences due to the impurities which are dirt and food residues. The liquid yield distribution concerning the aliphatic, mono-aromatic and poly-aromatic compounds varies as the ratio of PP waste increases in the waste plastic mixtures. In addition to this, the alkene/alkane ratio of gas products shows variations depending on the mixing ratio of wastes.     

Reaction Kinetic Model For Optimal Pyrolysis Of Plastic Waste Mixtures

Reaction kinetics at various temperatures for pyrolysis of mixtures of plastic waste [polyethylene(PE) and polystyrene(PS)] are modelled in terms of five types of pyrolysis reaction. The model development is based on the assumption that as plastic wastes are heated in a non-reactive environment they are decomposed homogeneously to various products of gas, oil and char by a first-order rate, irreversible reaction and isothermal condition. Among the five models, the type II model in which the activated polymer exists as an intermediate product is the most accurate in predicting the pyrolysis products of pure PE or pure PS. Also, for mixtures of plastics both type II and IV models can be used to explain the composition of pyrolysis products. Furthermore, from the analysis of variance (ANOVA), the mixing ratio and temperature are shown to be the parameters that have the greatest effect on the pyrolysis reaction of polymer waste mixture. The pyrolysis reaction time for the maximum oil production from PE-PS mixtures is shorter than for PE alone and approaches that of PS alone. Oil production increases with increase of PS content. The optimal temperature for maximum oil production is 600°C for the pyrolysis of 2:8, 5:5 and 1:0 mixtures (w/w) of PE and PS. Oil production for PS alone is constant when the pyrolysis is above 600°C.     

Synthesis of hydrogarnet from molten slag and its hydrogen chloride fixation performance at high temperature

Hydrogarnet was synthesized hydrothermally below 200°C using molten slag obtained from municipal solid waste. For comparison, it was also synthesized using pure-phase CaO–Al₂O₃–SiO₂–H₂O, as reported previously. The structural and textural properties of this material were investigated using various analytical and spectroscopic techniques such as X-ray diffraction, X-ray fluorescence spectrometry, atomic absorption spectrometry (AAS), thermogravimetry/differential thermal analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy. The Cl⁻ fixation ability of hydrogarnet was investigated in the temperature range 500–800°C in a fixed-bed flow reactor using a HCl concentration (1000 p.p.m.v.) similar to that of incinerator exhaust gas. Under these experimental conditions, the hydrogarnet was capable of reducing the HCl gas level to less than 1 p.p.m.v. Analysis of the spent catalyst revealed that the hydrogarnet was being transformed into wadalite and CaCl₂ at high temperatures. The elution test for chromium ions in hydrogarnet obtained from slag was also used, and it was found that chromium ions were not eluted from hydrogarnet. Received: January 27, 2001 / Accepted: October 11, 2001     

Determination of nitrous oxide, methane, and ammonia emissions from a swine waste composting process

The amounts of harmful gas emissions from the process of composting swine waste were determined using an experimental composting apparatus. Forced aeration (19.2–96.1 l/m³/min) was carried out continuously, and exhaust gases were collected and analyzed periodically. With weekly turning and the addition of a bulking agent in order to decrease the moisture content and increase air permeability, the temperature of most of the contents rose to 70°C and composting was complete within 3–5 weeks. NH₃, CH₄, and N₂O emissions were high in the early stage of composting. About 10%–25% of the nitrogen in the raw material was lost as NH₃ gas during composting. The emission rate of NH₃ mainly depended on the aeration rate, so that as the aeration rate rose, the level of NH₃ emissions increased. The CH₄ and N₂O emissions could be kept lower with adequate treatment at more than 40 l/m³/min aeration. N₂O may be mainly the result of the denitrification of NO _x -N in the additional matured compost used as a composting accelerator. Received: September 11, 1998 / Accepted: November 8, 1999     

Catalytic conversion of waste tyres into valuable hydrocarbons

Tyre recycling has become a necessity because of the huge piles of tyres that represent a threat to the environment. The used tyres represent a source of energy and valuable chemical products. Waste tyres were pyrolysed catalytically in a batch reactor under atmospheric pressure. Calcium carbide was used as a catalyst to explore its effect on pyrolysis product distribution. The effect of temperature, amount of catalyst and time on the yields of the pyrolysed products was investigated. Char yield decreased with increase of pyrolysis temperature while total gas and liquid yields increased. The liquid fraction was obtained with boiling point up to 320 °C. The physical and chemical properties of the pyrolysed products obtained were characterized. The catalytic pyrolysis produced 45 wt.% aromatic, 35 wt.% aliphatic and 20 wt.% of polar hydrocarbons. The distillation data showed that ∼80% of oil has boiling point below 270 °C which is the boiling point for 50% of distilled product in commercial diesel oil. The oil fraction was found to have high gross calorific value; GCV (42.8 MJ kg⁻¹). Its Specific gravity, viscosity, Kinematic viscosity, freezing point and diesel index were also within the limits of diesel fuel. The char residues were studied to investigate their characteristics for use as a possible adsorbent. Surface area of char before and after acid demineralization was determined to determine the adsorptive features for waste water treatment.     

Pyrolysis of plastic packaging waste: A comparison of plastic residuals from material recovery facilities with simulated plastic waste

Pyrolysis may be an alternative for the reclamation of rejected streams of waste from sorting plants where packing and packaging plastic waste is separated and classified. These rejected streams consist of many different materials (e.g., polyethylene (PE), polypropylene (PP), polystyrene (PS), polyvinyl chloride (PVC), polyethylene terephthalate (PET), acrylonitrile butadiene styrene (ABS), aluminum, tetra-brik, and film) for which an attempt at complete separation is not technically possible or economically viable, and they are typically sent to landfills or incinerators. For this study, a simulated plastic mixture and a real waste sample from a sorting plant were pyrolyzed using a non-stirred semi-batch reactor. Red mud, a byproduct of the aluminum industry, was used as a catalyst. Despite the fact that the samples had a similar volume of material, there were noteworthy differences in the pyrolysis yields. The real waste sample resulted, after pyrolysis, in higher gas and solid yields and consequently produced less liquid. There were also significant differences noted in the compositions of the compared pyrolysis products.