Microbial physiology-based model of ethanol metabolism in subsurface sediments

Dense non-aqueous phase liquids (DNAPLs) present in the subsurface may contain surface active compounds that impact DNAPL migration and distribution. While a number of studies have revealed the role surface active compounds play in altering the wettability of quartz sand, few have considered the implications for other minerals common to contaminated sites. This study extends understanding of DNAPL/surfactant wettability to iron oxide surfaces. Specifically, quartz and iron oxide-coated sands in a tetrachloroethene (PCE)/water system containing the organic base (an organic molecule that acts as a base) dodecylamine (DDA) were compared at a variety of scales. Wettability of the minerals' surfaces, and the impact of wettability on capillary resistance to DNAPL entry, were assessed as a function of pH through: (i) advancing and receding contact angles, (ii) primary drainage capillary pressure-saturation experiments, and (iii) small, two-dimensional, flow cell experiments. The work revealed that, at neutral pH and under identical boundary capillary pressures, DNAPL invaded quartz sand but not iron oxide-coated sand; however, at low pH, DNAPL invaded both sands equally. These differences were demonstrated to be due to wettability alterations associated with the strength of attractive forces between DDA and the mineral surface, dictated by the isolectric point of the minerals and system pH. Observed differences in DNAPL invasion behavior were consistent with measured intrinsic contact angles and P(c)-S relationships, the latter requiring scaling by the operative contact angle inside the porous medium for a meaningful comparison. This study suggests that the distribution of minerals (and, more specifically, their isoelectric points), as well as the aqueous phase pH at a given site, may have a significant impact on the DNAPL source zone architecture.     

The role of interfacial films in the mass transfer of naphthalene from creosotes to water

Viscous, semi-rigid interfacial films that are formed at the interface of certain multi-component non-aqueous phase liquid (NAPLs) and water can significantly reduce the rates of mass transfer of solutes. Creosote-water systems were investigated for their ability to form interfacial films. The effects of these films on the creosote-water partition and on mass transfer of a representative solute, naphthalene, were investigated in a series of experiments. The area-independent mass transfer coefficient of naphthalene contained in creosote decreased by 30% over a 1-week period in systems containing creosote and water. Further aging for up to 21 days did not result in significant additional decreases in the mass transfer coefficient. The creosote-water partition coefficient, however, did not change with extended contact. The presence of viscous interfacial films in creosote-water systems was demonstrated in pendant drop tests. These interfacial films most likely caused the reduction in solute mass transfer coefficients by providing significant resistance to the diffusion of solutes through the interfacial film. Results from mass transfer experiments conducted under different system conditions suggested that hindered diffusion of naphthalene through the bulk creosote phase, changes in composition of creosote as a result of extended dissolution, or changes in creosote-water interfacial area did not contribute to the decrease in naphthalene mass transfer coefficient.     

Simulation of organic liquid flow in porous media using estimated and measured transport properties

Many numerical models which describe the movement of a separate organic liquid phase in the subsurface require information about the relationships between capillary pressure and saturation, and between relative permeability and saturation. An evaluation of the information available for these relationships suggests that substantial discrepancies may be introduced into simulations if estimated, rather than measured, data are employed. The purpose of this study was to quantify these deviations. Two-phase displacement simulations were performed in one and two dimensions for several organic liquid-water systems. Both constant-head and constant-flux boundary conditions were employed at a variety of flow rates and time scales, using both measurements and estimates of capillary pressure and relative permeability for a sandy aquifer material. The results demonstrate that the use of estimated transport relationships produces significantly different predictions of organic liquid migration. The magnitude of the deviations between predictions may be as high as 25% or more after relatively short displacement periods, depending on the boundary conditions of the simulated scenario, as well as on the physical characteristics of the two-phase system. For the systems examined, most of the deviations resulted from the estimates for relative permeability to the organic liquid. Thus, improved methods for the estimation of the relative permeability to the organic liquid are needed to reduce the uncertainty in displacement simulations.     

Influence of surfactant-facilitated interfacial tension reduction on chlorinated solvent migration in porous media: observations and numerical simulation

The ability of a multiphase flow model to capture the migration behavior of chlorinated solvents under conditions of surfactant-facilitated interfacial tension (IFT) reduction is assessed through comparison of model predictions with observations from controlled laboratory experiments. Tetrachloroethene (PCE) was released in two-dimensional saturated systems, packed with sandy media that incorporated rectangular lenses of capillary contrast. Spatially uniform interfacial tension conditions were created in the tanks by pre-flushing the porous medium with either Milli Q water or an aqueous surfactant solution. Experimental observations showed that surfactant-facilitated IFT reductions substantially lowered capillary resistance to the vertical downward migration of PCE and enabled PCE to enter finer grained, less permeable lenses that were not penetrated in the absence of surfactant. An immiscible flow model was used to simulate the conditions of the laboratory experiments. Under higher IFT conditions (47.5 and 5 dyn/cm), the model could successfully predict the general migration behavior of the organic liquid. Model predictions, however, exhibited poorer agreement with observed migration pathways under low IFT conditions (0.5 dyn/cm). In all cases, the predicted PCE distributions were influenced by selection of the parametric model for capillary retention and relative permeability. Simulated migration rates were more consistent with observed behavior when the Brooks-Corey/Burdine model was employed. For low interfacial tensions, improved predictions of migration pathways were obtained through grid refinement and incorporation of small-scale packing variability. Simulations highlight the substantial sensitivity of model predictions to the capillary pressure-scaling factor, grid resolution, and small-scale porosity variations at interfaces of permeability contrast under reduced IFT conditions.     

Surfactant-induced changes in gravity fingering of water through a light oil

Gravity-driven preferential flow (fingering) can greatly affect how one fluid displaces another in the subsurface. We have studied the internal properties of these preferential flow paths for water, with and without surfactants, infiltrating into oil saturated porous media using synchrotron X-rays, and miniature tensiometers to characterize fluid content and pressure relationships. We also used a light transmission technique to visualize overall flow pattern. Capillary pressure and water content decrease behind the front, similar to fingers in air-dry sand, with quantitative differences for five different surfactants with surface tensions ranging from 4–21 g/s². Using unstable flow theory, the finger widths, capillary pressure drops within the fingers, finger tip lengths, and finger splitting dynamics were scaled successfully with interfacial tension, fluid density, and the contact angle using the fingers in air–water systems as the reference.     

pH和负压对生活垃圾焚烧厂渗沥液蒸发处理的影响

生活垃圾焚烧厂贮坑渗沥液含有弱电解质类的挥发性污染物,pH和压强是影响其蒸发过程中气液相分布的主要因素,实验研究了蒸发操作压强及渗沥液初始pH对蒸发冷凝液中污染物分配的影响.结果表明,操作压强16～39kPa对冷凝液的组成基本没有影响;而pH的变化则改变了挥发性弱电解质类污染物在渗沥液中的存在形态,进而显著地改变了其在冷凝液中的分配情况.当渗沥液的初始pH为5时,冷凝液主要成份为挥发性有机酸和低碳醇类物质,不含氨氮;pH＞10时,冷凝液中挥发性有机酸减少,氨氮增加.渗沥液原液经一级蒸发可显著改善其可处理性.     

Towards a better understanding of tetrachloroethene entry pressure in the matrix of Permo-Triassic sandstones

The pressure required for a chlorinated solvent to enter a geological medium can be calculated given knowledge of the characteristic pore size of the medium and the interfacial tension (IFT) and contact angle of the solvent-water-rock system. Using a centrifuge-based method, capillary pressure-saturation curves have been determined for 30 water-saturated samples of Permo-Triassic sandstones for the solvent tetrachloroethene (PCE). These curves have been successfully fitted using the van Genuchten function to determine PCE entry pressure for each of the sandstone samples. A plot of PCE entry pressures against average pore diameter shows a linear relationship in log-log space; however, observed values for PCE entry pressure are significantly lower than would be expected theoretically for a sandstone-PCE-water system. This may be explained either by a decrease in the IFT or an increase in the contact angle. The IFT may decrease during contact with sandstones due to hysteresis effects during imbibition and drainage of fluids, but this is unlikely to be sufficient to account for the low entry pressures observed. Therefore, it is inferred that the low observed PCE entry pressures are due to higher than expected PCE contact angles, and that the average pore-throat surface of the sandstones is more solvent wetting than would be expected. A weak acid extraction indicates the presence of calcite and dolomite in the sandstone cores, and a correlation is observed between carbonate content per unit porosity and a reduction in PCE entry pressure. It is suggested that these mineral phases are responsible for observed wettability changes and a conceptual model is proposed. One consequence of the lower observed entry pressures is that solvents are likely to penetrate deeper into the matrix of water-saturated sandstones than previously expected.     

Surfactant enhanced recovery of tetrachloroethylene from a porous medium containing low permeability lenses. 2. Numerical simulation

A numerical model of surfactant enhanced solubilization was developed and applied to the simulation of nonaqueous phase liquid recovery in two-dimensional heterogeneous laboratory sand tank systems. Model parameters were derived from independent, small-scale, batch and column experiments. These parameters included viscosity, density, solubilization capacity, surfactant sorption, interfacial tension, permeability, capillary retention functions, and interphase mass transfer correlations. Model predictive capability was assessed for the evaluation of the micellar solubilization of tetrachloroethylene (PCE) in the two-dimensional systems. Predicted effluent concentrations and mass recovery agreed reasonably well with measured values. Accurate prediction of enhanced solubilization behavior in the sand tanks was found to require the incorporation of pore-scale, system-dependent, interphase mass transfer limitations, including an explicit representation of specific interfacial contact area. Predicted effluent concentrations and mass recovery were also found to depend strongly upon the initial NAPL entrapment configuration. Numerical results collectively indicate that enhanced solubilization processes in heterogeneous, laboratory sand tank systems can be successfully simulated using independently measured soil parameters and column-measured mass transfer coefficients, provided that permeability and NAPL distributions are accurately known. This implies that the accuracy of model predictions at the field scale will be constrained by our ability to quantify soil heterogeneity and NAPL distribution.     

Influence of dissolved humic substances on the mass transfer of organic compounds across the air-water interface

The effect of dissolved humic substances (DHS) on the rate of water-gas exchange of two volatile organic compounds was studied under various conditions of agitation intensity, solution pH and ionic strength. Mass-transfer coefficients were determined from the rate of depletion of model compounds from an apparatus containing a stirred aqueous solution with continuous purging of the headspace above the solution (dynamic system). Under these conditions, the overall transfer rate is controlled by the mass-transfer resistance on the water side of the water-gas interface. The experimental results show that the presence of DHS hinders the transport of the organic molecules from the water into the gas phase under all investigated conditions. Mass-transfer coefficients were significantly reduced even by low, environmentally relevant concentrations of DHS. The retardation effect increased with increasing DHS concentration. The magnitude of the retardation effect on water-gas exchange was compared for Suwannee River fulvic and humic acids, a commercially available leonardite humic acid and two synthetic surfactants. The observed results are in accordance with the concept of hydrodynamic effects. Surface pressure forces due to surface film formation change the hydrodynamic characteristics of water motion at the water-air interface and thus impede surface renewal.     

Surface tension of aqueous solutions of water-soluble organic and inorganic compounds

Surface tension of pure and mixed aqueous solutions of both inorganic and organic species that are relevant in atmospheric droplets has been studied in a laboratory investigation. Following the Gibbsian theory of surfaces experimental data have been fitted by the Szyszkowski equation. As a function of the carbon-chain length trends in the maximum surface excess Γ_max and the inverse surface activity β have been clearly identified for pure aqueous solutions of homologous series of n-alcohols and mono-carboxylic acids, while these parameters oscillate for the homologous series of di-carboxylic acids. For mixed aqueous solutions of water-soluble organic and inorganic compounds, e.g. cis-pinonic acid and sodium chloride, a further decrease in surface tension has been observed, which can be interpreted as an interaction between the inorganic and organic solutes and an enrichment of the surface-active organic compound in the surface layer. Taking this effect into account surface-tension data of real atmospheric samples become more plausible, especially when also slightly soluble or water-insoluble organic compounds having a high surface activity at low concentrations are considered.     

Removal of DNAPL contamination from the saturated zone by the combined effect of vertical upward flushing and density reduction

A common aspect of innovative remediation techniques is that they tend to reduce the interfacial tension between the aqueous and non-aqueous phase liquids, resulting in mobilization of the organic contaminant. This complicates the remediation of aquifers, contaminated with Dense Non-Aqueous Phase Liquids (DNAPLs), as they are likely to migrate downwards, deeper into the aquifer and into finer layers. A possible solution is the use of swelling alcohols, which tend to reduce the density difference between the aqueous phase and the DNAPL. To avoid premature mobilization upon the initial contact between the DNAPL and the alcohol, several researchers have proposed the use of vertical upward flow of the alcohol. In this paper, we present an equation, which describes the upward mobilization of both continuous and discontinuous DNAPLs and so the important parameters governing the upward controlled mobilization of the DNAPL. The need and required magnitude of this specific discharge was investigated by conducting four column experiments in which the initial density of the DNAPL and the permeability was varied. It was shown that the required flow velocities increase with the permeability of the porous medium and the initial density difference between the aqueous phase and the DNAPL. Whenever the specific discharge falls below the critical value, the DNAPL moves downward. A second set of column experiments looked at the impact of permeability of porous medium on the solubilization and mobilization of DNAPL during alcohol flooding. Columns, packed with coarse or fine sand, containing a residual trichloroethylene (TCE) or perchloroethylene (PCE) saturation were flushed with the alcohol mixture at a fixed specific discharge rate. The induced pressure gradients in the aqueous phase, which were higher in the fine sand, resulted for this porous medium in extensive mobilization of the DNAPL against the direction of the buoyancy force. The density of the first NAPL coming out of the top of the fine sand was close to that of the pure DNAPL. In the coarser sand, the pressure gradients were sufficient to prevent downward migration of the DNAPL, but upward mobilization was minimal. The predominant removal mechanism in this case was the much slower solubilization.     

Secondary imbibition in NAPL-invaded mixed-wet sediments

A previously developed pore network model is used here to study the spontaneous and forced secondary imbibition of a NAPL-invaded sediment, as in the displacement of NAPL by waterflooding a mixed-wet soil. We use a 3D disordered pore network with a realistic representation of pore geometry and connectivity, and a quasi-static displacement model that fully describes the pore-scale physics. After primary drainage (NAPL displacing water) up to a maximum capillary pressure, we simulate secondary imbibition (water displacing NAPL). We conduct a parametric study of imbibition by varying systematically the controlling parameters: the advancing contact angles, the fraction of NAPL-wet pores, the interfacial tension, and the initial water saturation. Once the secondary imbibition is completed, the controlling displacement mechanisms, capillary pressures, relative permeabilities, and trapped NAPL saturations are reported. It is assumed that NAPL migrates into an initially strongly water-wet sediment, i.e., the receding contact angles are very small. However, depending on the surface mineralogy and chemical compositions of the immiscible fluid phases, the wettability of pore interiors is altered while the neighborhoods of pore corners remain strongly water-wet-resulting in a mixed-wet sediment. Here, we compare three different levels of wettability alteration: water-wet (advancing contact angles (20 degrees to 55 degrees), intermediate-wet (55 degrees to 120 degrees), and NAPL-wet (120 degrees to 155 degrees). The range of advancing contact angles and the fraction of NAPL-wet pores have dramatic effects on the NAPL-water capillary pressures and relative permeabilities. The spatially inhomogeneous interfacial tension has a minor impact on the trapped NAPL saturation and relative permeability to NAPL, and a slight effect on the relative permeability to water. The initial water saturation has a slight effect on the two-phase flow characteristics of water-wet sediments; however, with more NAPL-wet pores in the sediment, it starts to have a profound effect on the water and NAPL relative permeabilities.     

Significance of analytical parameters for the understanding of natural organic matter in relation to photocatalytic oxidation

In this review, special interest was devoted to provide information on the surrogate parameters expressing both quality and quantity of organic matter for the understanding of the photocatalytic oxidation of humic substances. Detailed investigation was directed to the application of photocatalysis with reference to source, origin and modeling of organic matter. Evaluation of the literature findings emphasizes that organic matter taken from natural waters are site specific and should be characterized in detail to be comparable to other studies. Taking into account the photocatalytic degradation studies of natural organic matter, humic substances, humic acids and fulvic acids in slurry systems, a procedure could be deduced that depends on the selection of a standard model sample with a representative concentration, selection of a standard photocatalyst and dose (e.g., TiO₂ Degussa P-25, 0.25 mg mL⁻¹), application of standardized reaction conditions such as light intensity, pH, and temperature. Furthermore, standardized filtration step avoiding organic leaching and selection of the most suitable analytical parameter are the crucial points to be considered. The use of such a protocol could form a basis for the determination of “relative degradation efficiency” of any sample containing natural organic matter, humic substances, humic acids and fulvic acids regardless of dependency on source and origin.     

A compositional simulator for modeling surfactant enhanced aquifer remediation, 1 formulation

We describe a three-dimensional, multicomponent, multiphase compositional finite-difference simulator for application to the analysis of contaminant transport and surfactant enhanced aquifer remediation (SEAR) of nonaqueous-phase liquid (NAPL) pollutants. Mixtures of surfactant, water and NAPL can form many types of micellar and microemulsion phases with a complex and important dependence on many variables of which the dilute aqueous solution typically assumed in SEAR models is just one example. The phase behavior model is central to our approach and allows for the full range of the commonly observed micellar and microemulsion behavior pertinent to SEAR. The other surfactant related properties such as adsorption, interfacial tension, capillary pressure, capillary number and microemulsion viscosity are all dependent on an accurate phase behavior model. This has proven to be a highly successful approach for surfactant enhanced oil recovery modeling, so it was adapted to SEAR modeling. However, there are many significant differences between petroleum and environmental applications of surfactants, so many new features have been added to model contaminant transport and remediation and these are described and illustrated for the first time here.     

Fugacity modelling to predict the distribution of organic contaminants in the soil:oil matrix of constructed biopiles

Level I and II fugacity approaches were used to model the environmental distribution of benzene, anthracene, phenanthrene, 1-methylphenanthrene and benzo[a]pyrene in a four phase biopile system, accounting for air, water, mineral soil and non-aqueous phase liquid (oil) phase. The non-aqueous phase liquid (NAPL) and soil phases were the dominant partition media for the contaminants in each biopile and the contaminants differed markedly in their individual fugacities. Comparison of three soils with different percentage of organic carbon (% org C) showed that the % org C influenced contaminant partitioning behaviour. While benzene showed an aqueous concentration worthy of note for leachate control during biopiling, other organic chemicals showed that insignificant amount of chemicals leached into the water, greatly reducing the potential extent of groundwater contamination. Level II fugacity model showed that degradation was the dominant removal process except for benzene. In all three biopile systems, the rate of degradation of benzo(a)pyrene was low, requiring more than 12 years for soil concentrations from a spill of about 25 kg (100 mol) to be reduced to a concentration of 0.001 microgg(-1). The removal time of 1-methylphenanthrene and either anthracene or phenanthrene was about 1 and 3 years, respectively. In contrast, benzene showed the highest degradation rate and was removed after 136 days in all biopile systems. Overall, this study confirms the association of risk critical contaminants with the residual saturation in treated soils and reinforces the importance of accounting for the partitioning behaviour of both NAPL and soil phases during the risk assessment of oil-contaminated sites.     

Improving the extraction of tetrachloroethylene from soil columns using surfactant gradient systems

In this work, we extend the recently developed gradient approach for surfactant-enhanced remediation of dense non-aqueous phase liquid (DNAPL)-impacted sites. The goal of the gradient approach is to maximize the DNAPL solubilization capacity in swollen micelles (Type I aqueous microemulsions) while at the same time minimizing the potential for DNAPL mobilization. In this work, we introduce a modified version of the capillary/trapping curve that we refer to as the gradient curve to help interpret and/or design the gradient approach. The gradient curve presents the residual DNAPL saturation as a function of interfacial tension and microemulsion viscosity. This approach demonstrates that keeping a low viscosity of the microemulsion phase is not only important for keeping a low head loss during surfactant flooding but also to prevent oil mobilization. Eight microemulsion systems were evaluated in this research; these systems were evaluated based on their tetrachloroethylene (PCE) solubilization capacity, interfacial tension (IFT), viscosity, density, and coalescence kinetics. Two of these systems were chosen for evaluation in site-specific column tests using an increasing electrolyte gradient to produce a decreasing IFT/increasing solubilization gradient system. The column studies were conducted with media from Dover Air Force Base in Dover, DE. Both solubilized and mobilized DNAPL were quantified. During the column studies, we observed that substantial PCE was mobilized when the residual level of PCE in the column was significantly higher than the steady-state residual saturation level being approach (as predicted from the gradient curve). Four column studies were performed, three of which were used to asses the validity of the gradient curve in predicting the residual saturation after each gradient step. From these tests we observed that starting IFTs of less than 1 mN/m all produced the same mobilization potential. In the last column, we used an additional gradient step with an initial IFT above 1 mN/m to dramatically reduce the amount of PCE mobilize. Based on the good agreement between column results and projections based on the gradient curve, we propose this as a preferred method for designing gradient surfactant flushing systems.     

Effect of nonionic surfactant partitioning on the dissolution kinetics of residual perchloroethylene in a model porous medium

At concentrations above the critical micelle concentration, surfactants can significantly enhance the solubilization of residual nonaqueous phase liquids (NAPL) and, for this reason, are the focus of research on surfactant-enhanced aquifer remediation (SEAR). As a consequence of their amphiphilic nature, surfactants may also partition to various extents between the organic and aqueous phases, thereby affecting SEAR performance. We report here on the observation and analysis of the effect of surfactant partitioning on the dissolution kinetics of residual perchloroethylene (PCE) by aqueous solutions (1000 mg/L) of the non-ionic surfactant Triton X-100 in a model porous medium. For this fluid system, batch equilibration experiments showed that the surfactant partitions strongly into the NAPL (NAPL-water partition coefficient equal to 12.5). Dynamic interfacial tension (IFT) measurements were employed to study surfactant diffusion and interfacial adsorption. The dynamic IFT measurements were consistent with partitioning of the surfactant between the two liquid phases. PCE dissolution experiments, conducted in a transparent glass micromodel using an aqueous surfactant solution, were contrasted to experiments using clean water. Surfactant partitioning was observed to delay significantly the onset of micellar solubilization of PCE, an observation reproduced by a numerical model. This effect is attributed to the reduction of surfactant concentration in the immediate vicinity of the NAPL-water interface, which accompanies transport of the surfactant into the NAPL. Accordingly, it is suggested that both the rate and the extent of diffusion of the surfactant into the NAPL affect the onset of and the driving force for micellar solubilization. While many surfactants do not readily partition in NAPL, this possibility must be considered when selecting non-ionic surfactants for the enhanced solubilization of residual chlorinated solvents in porous media.     

Mobilization and entry of DNAPL pools into finer sand media by cosolvents: two-dimensional chamber studies

Two-dimensional chamber studies were conducted to determine qualitative and quantitative performance of cosolvents targeted at pooled dense non-aqueous phase liquid (DNAPL) (perchlorethylene, PCE) residing above a fine-grain capillary barrier. Downward mobilization of DNAPL, up gradient along an overriding cosolvent front, was observed. This produced significant pooling above a fine-grain layer that in some cases lead to entry into the capillary barrier beneath. Entry pressure calculations using physical and hydrogeologic parameters provided an excellent prediction of breakthrough of DNAPL into the capillary barrier. Calculations predict approximately 0.5 m of DNAPL would be necessary to enter a Beit Netofa clay, under extreme cosolvent flooding conditions (100% ethanol). Gradient injection of cosolvent did not appear to provide any benefit suggesting a rapid decrease in interfacial tension (IFT) compared to the rate of DNAPL solubilization. Use of a partitioning alcohol (tertiary butyl alcohol, TBA) resulted in DNAPL swelling and reduced entry into the capillary barrier. However, the trapping of flushing solution, containing PCE, could potentially lead to longer remediation times.     

表面活性剂冲洗修复多氯联苯污染土壤多相流研究

多氯联苯(PCBs)是一种具有持久性、抗生物降解性、脂肪溶性和明显的生物毒性等特性的持久性有机污染物,PCBs在土壤中难于准确定位、难被分解和强烈吸附,去除土壤中PCBs比较困难.表面活性剂冲洗法可以通过提高PCBs溶解度和降低水-PCBs界面张力来实现PCBs从土壤中去除;表面活性剂冲洗PCBs污染土壤涉及气相、水相、NAPLs相和固相等物质,是多相共存并相互发生作用的过程,发生相对渗透率、饱和度和毛细压力的变化;另外,为研究表面活性剂冲洗土壤中PCBs的去除机理,并降低PCBs对研究人员的危害,采用微观孔隙结构网络模型是一种较新颖的和效果显著的研究方法.开展表面活性剂冲洗PCBs污染土壤多相流研究,可以为PCBs污染场地修复提供理论基础和实验支持,并促进我国POPs履约工作的顺利进行.