U. S. EPA Views as “Unwarranted” Federal Regulatory Involvement in Odor Control

ABSTRACT

Although there have been several studies examining emissions of criteria pollutants from in-use alternative fuel vehicles (AFVs), little is known about emissions of hazardous air pollutants (HAPs) from these vehicles. This paper explores HAP tailpipe emissions from a variety of AFVs operating in the federal government fleet and compares these emissions to emissions from identical vehicles operating on reformulated gasoline. Emissions estimates are presented for a variety of fuel/model combinations and on four HAPs (acetaldehyde, 1,3-butadi-ene, benzene, and formaldehyde). The results indicate that all AFVs tested offer reduced emissions of HAPs, with the following exceptions: ethanol fueled vehicles emit more acetaldehyde than RFG vehicles, and ethanol- and methanol-fueled vehicles emit more formaldehyde than RFG vehicles. The results from this paper can lead to more accurate emissions factors for HAPs, thus improving HAP inventory and associated risk estimates for both AFVs and conventional vehicles.     

Codependencies of reactive air toxic and criteria pollutants on emission reductions

It is important to understand the effects of emission controls on concentrations of ozone, fine particulate matter (PM2.5), and hazardous air pollutants (HAPs) simultaneously, to evaluate the full range of health, ecosystem, and economic effects. Until recently, the capability to simultaneously evaluate interrelated atmospheric pollutants ("one atmosphere" analysis) was unavailable to air quality managers. In this work, we use an air quality model to examine the potential effect of three emission reductions on concentrations of ozone, PM2.5, and four important HAPs (formaldehyde, acetaldehyde, acrolein, and benzene) over a domain centered on Philadelphia for 12-day episodes in July and January 2001. Although NO(x) controls are predicted to benefit PM2.5 concentrations and sometimes benefit ozone, they have only a small effect on formaldehyde, slightly increase acetaldehyde and acrolein, and have no effect on benzene in the July episode. Concentrations of all pollutants except benzene increase slightly with NO(x) controls in the January simulation. Volatile organic compound controls alone are found to have a small effect on ozone and PM2.5, a less than linear effect on decreasing aldehydes, and an approximately linear effect on acrolein and benzene in summer, but a slightly larger than linear effect on aldehydes and acrolein in winter. These simulations indicate the difficulty in assessing how toxic air pollutants might respond to emission reductions aimed at decreasing criteria pollutants such as ozone and PM2.5.     

Overview of the U.S. Environmental Protection Agency's Hazardous Air Pollutant Early Reduction Program.

Under provision of the Clean Air Act Amendments of 1990 Title III, the EPA has proposed a regulation (Early Reduction Program) to allow a six-year compliance extension from Maximum Achievable Control Technology (MACT) standards for sources that voluntarily reduce emissions of Hazardous Air Pollutants (HAPs) by 90 percent or more (95 percent or more for particulates) from a base year of 1987 or later. The emission reduction must be made before the applicable MACT standard is proposed for the source category or be subject to an enforceable commitment to achieve the reduction by January 1, 1994 for sources subject to MACT standards prior to 1994. The primary purpose of this program is to encourage reduction of HAPs emissions sooner than otherwise required. Industry would be allowed additional time in evaluating emission reduction options and developing more cost-effective compliance strategies, although, under strict guidelines to ensure actual, significant and verifiable emission reductions occur.     

An analysis of candidates for addition to the Clean Air Act list of hazardous air pollutants

There are 188 air toxics listed as hazardous air pollutants (HAPs) in the Clean Air Act (CAA), based on their potential to adversely impact public health. This paper presents several analyses performed to screen potential candidates for addition to the HAPs list. We analyzed 1086 HAPs and potential HAPs, including chemicals regulated by the state of California or with emissions reported to the Toxics Release Inventory (TRI). HAPs and potential HAPs were ranked by their emissions to air, and by toxicity-weighted (tox-wtd) emissions for cancer and noncancer, using emissions information from the TRI and toxicity information from state and federal agencies. Separate consideration was given for persistent, bioaccumulative toxins (PBTs), reproductive or developmental toxins, and chemicals under evaluation for regulation as toxic air contaminants in California. Forty-four pollutants were identified as candidate HAPs based on three ranking analyses and whether they were a PBT or a reproductive or developmental toxin. Of these, nine qualified in two or three different rankings (ammonia [NH3], copper [Cu], Cu compounds, nitric acid [HNO3], N-methyl-2-pyrrolidone, sulfuric acid [H2SO4], vanadium [V] compounds, zinc [Zn], and Zn compounds). This analysis suggests further evaluation of several pollutants for possible addition to the CAA list of HAPs.     

Codependencies of Reactive Air Toxic and Criteria Pollutants on Emission Reductions

Abstract

It is important to understand the effects of emission controls on concentrations of ozone, fine particulate matter (PM_2.5), and hazardous air pollutants (HAPs) simultaneously, to evaluate the full range of health, ecosystem, and economic effects. Until recently, the capability to simultaneously evaluate interrelated atmospheric pollutants (“one atmosphere” analysis) was unavailable to air quality managers. In this work, we use an air quality model to examine the potential effect of three emission reductions on concentrations of ozone, PM_2.5, and four important HAPs (formaldehyde, acetaldehyde, acrolein, and benzene) over a domain centered on Philadelphia for 12-day episodes in July and January 2001. Although NO_x controls are predicted to benefit PM_2.5 concentrations and sometimes benefit ozone, they have only a small effect on formaldehyde, slightly increase acetaldehyde and acrolein, and have no effect on benzene in the July episode. Concentrations of all pollutants except benzene increase slightly with NO_x controls in the January simulation. Volatile organic compound controls alone are found to have a small effect on ozone and PM_2.5, a less than linear effect on decreasing aldehydes, and an approximately linear effect on acrolein and benzene in summer, but a slightly larger than linear effect on aldehydes and acrolein in winter. These simulations indicate the difficulty in assessing how toxic air pollutants might respond to emission reductions aimed at decreasing criteria pollutants such as ozone and PM_2.5.     

Assessment of volatile organic compound and hazardous air pollutant emissions from oil and natural gas well pads using mobile remote and on-site direct measurements

Emissions of volatile organic compounds (VOCs) and hazardous air pollutants (HAPs) from oil and natural gas production were investigated using direct measurements of component-level emissions on pads in the Denver-Julesburg (DJ) Basin and remote measurements of production pad-level emissions in the Barnett, DJ, and Pinedale basins. Results from the 2011 DJ on-site study indicate that emissions from condensate storage tanks are highly variable and can be an important source of VOCs and HAPs, even when control measures are present. Comparison of the measured condensate tank emissions with potentially emitted concentrations modeled using E&P TANKS (American Petroleum Institute [API] Publication 4697) suggested that some of the tanks were likely effectively controlled (emissions less than 95% of potential), whereas others were not. Results also indicate that the use of a commercial high-volume sampler (HVS) without corresponding canister measurements may result in severe underestimates of emissions from condensate tanks. Instantaneous VOC and HAP emissions measured on-site on controlled systems in the DJ Basin were significantly higher than VOC and HAP emission results from the study conducted by Eastern Research Group (ERG) for the City of Fort Worth (2011) using the same method in the Barnett on pads with low or no condensate production. The measured VOC emissions were either lower or not significantly different from the results of studies of uncontrolled emissions from condensate tanks measured by routing all emissions through a single port monitored by a flow measurement device for 24 hr. VOC and HAP concentrations measured remotely using the U.S. Environmental Protection Agency (EPA) Other Test Method (OTM) 33A in the DJ Basin were not significantly different from the on-site measurements, although significant differences between basins were observed.

Implications: VOC and HAP emissions from upstream production operations are important due to their potential impact on regional ozone levels and proximate populations. This study provides information on the sources and variability of VOC and HAP emissions from production pads as well as a comparison between different measurement techniques and laboratory analysis protocols. On-site and remote measurements of VOC and HAP emissions from oil and gas production pads indicate that measurable emissions can occur despite the presence of control measures, often as a result of leaking thief hatch seals on condensate tanks. Furthermore, results from the remote measurement method OTM 33A indicate that it can be used effectively as an inspection technique for identifying oil and gas well pads with large fugitive emissions.     

Atmospheric Chemistry of Toxic Contaminants. 2. Saturated Aliphatics: Acetaldehyde,Dioxane, Ethylene Glycol Ethers,Propylene Oxide

Detailed mechanisms are outlined for the chemical reactions that contribute to In-situ formation and atmospheric removal of the saturated aliphatic contaminants acetaldehyde, dioxane, ethylene glycol ethers (methyl, ethyl, n-butyl) and propylene oxide. In-situ formation Is of major Importance for acetaldehyde. In-situ removal Involves reaction with OH (all compounds) and, for acetaldehyde, photolysis and reaction with NO3. Acetaldehyde, dioxane, and the ethers are rapidly removed (half-lives of less than one day), leading to PAN (acetaldehyde) and to 2-oxodioxane and formaldehyde (dioxane). Reaction products of the glycol ethers include a large number of hydroxyesters, hydroxyacids, and hydroxycarbonyls. Propylene oxide reacts only slowly with OH, with an atmospheric half-life of 3-10 days, to yield formaldehyde, acetaldehyde, and PAN. Uncertainties in the reaction mechanisms for dioxane, the glycol ethers, and propylene oxide are discussed and include C-C vs C-0 bond scission in alkoxy radicals as well as alkoxy radical unimolecular decomposition vs reaction with oxygen.     

National review of ambient air toxics observations

Ambient air observations of hazardous air pollutant (HAPs), also known as air toxics, derived from routine monitoring networks operated by states, local agencies, and tribes (SLTs), are analyzed to characterize national concentrations and risk across the nation for a representative subset of the 187 designated HAPs. Observations from the National Air Toxics Trend Sites (NATTS) network of 27 stations located in most major urban areas of the contiguous United States have provided a consistent record of HAPs that have been identified as posing the greatest risk since 2003 and have also captured similar concentration patterns of nearly 300 sites operated by SLTs. Relatively high concentration volatile organic compounds (VOCs) such as benzene, formaldehyde, and toluene exhibit the highest annual average concentration levels, typically ranging from 1 to 5 µg/m³. Halogenated (except for methylene chloride) and semivolatile organic compounds (SVOCs) and metals exhibit concentrations typically 2–3 orders of magnitude lower. Formaldehyde is the highest national risk driver based on estimated cancer risk and, nationally, has not exhibited significant changes in concentration, likely associated with the large pool of natural isoprene and formaldehyde emissions. Benzene, toluene, ethylbenzene, and 1,3-butadiene are ubiquitous VOC HAPs with large mobile source contributions that continue to exhibit declining concentrations over the last decade. Common chlorinated organic compounds such as ethylene dichloride and methylene chloride exhibit increasing concentrations. The variety of physical and chemical attributes and measurement technologies across 187 HAPs result in a broad range of method detection limits (MDLs) and cancer risk thresholds that challenge confidence in risk results for low concentration HAPs with MDLs near or greater than risk thresholds. From a national monitoring network perspective, the ability of the HAPs observational database to characterize the multiple pollutant and spatial scale patterns influencing exposure is severely limited and positioned to benefit by leveraging a variety of emerging measurement technologies.

Implications:?Ambient air toxics observation networks have limited ability to characterize the broad suite of hazardous air pollutants (HAPs) that affect exposures across multiple spatial scales. While our networks are best suited to capture major urban-scale signals of ubiquitous volatile organic compound HAPs, incorporation of sensing technologies that address regional and local-scale exposures should be pursued to address major gaps in spatial resolution. Caution should be exercised in interpreting HAPs observations based on data proximity to minimum detection limit and risk thresholds.     

Carbon isotope analysis for source identification of atmospheric formaldehyde and acetaldehyde in Dinghushan Biosphere Reserve in South China

Formaldehyde and acetaldehyde are two most abundant carbonyls in ambient air. Biogenic emission has been proposed as a significant source other than anthropogenic emissions and atmospheric secondary formation. Here at a forest site in South China, the carbon isotopic compositions of formaldehyde and acetaldehyde emitted from leaves of three tree species (Litsea rotundifolia, Canarium album and Castanea henryi) were measured in comparison with the bulk carbon isotopic compositions of tree leaves. δ¹³C data of the emitted aldehydes (from ?31‰ to ?46‰) were quite different for tree species, which were all more depleted in ¹³C than the tree-leaf bulk δ¹³C values (from ?27‰ to ?32‰). Formaldehyde in ambient air at the forest site had δ¹³C values different from those of leaf-emitted formaldehyde, indicating other sources for ambient formaldehyde apart from direct emission from leaves, most probably the photooxidation of biogenic hydrocarbon like isoprene and monoterpene. The δ¹³C differences of acetaldehyde between ambient data and those of tree leaves emission were less than 1‰, implying direct biogenic emission as the dominant source.     

National estimates of outdoor air toxics concentrations

The Clean Air Act identifies 189 hazardous air pollutants (HAPs), or "air toxics," associated with a wide range of adverse human health effects. The U.S. Environmental Protection Agency has conducted a modeling study with the Assessment System for Population Exposure Nationwide (ASPEN) to gain a greater understanding of the spatial distribution of concentrations of these HAPs resulting from contributions of multiple emission sources. The study estimates year 1990 long-term outdoor concentrations of 148 air toxics for each census tract in the continental United States, utilizing a Gaussian air dispersion modeling approach. Ratios of median national modeled concentrations to estimated emissions indicate that emission totals without consideration of emission source type can be a misleading indicator of air quality. The results also indicate priorities for improvements in modeling methodology and emissions identification. Model performance evaluation suggests a tendency for underprediction of observed concentrations, which is likely due, at least in part, to a number of limitations of the Gaussian modeling formulation. Emissions estimates for HAPs have a high degree of uncertainty and contribute to discrepancies between modeled and monitored concentration estimates. The model's ranking of concentrations among monitoring sites is reasonably good for most of the gaseous HAPs evaluated, with ranking accuracy ranging from 66 to 100%.     

Seasonal impact of blending oxygenated organics with gasoline on motor vehicle tailpipe and evaporative emissions.

Emissions from a 1988 GM Corsica with adaptive learning closed loop control were measured with 4 fuels at 40, 75, and 90 degrees F. Evaporative and exhaust emissions were examined from each fuel at each test temperature. Test fuels were unleaded summer grade gasoline; a blend of this gasoline containing 8.1 percent ethanol; a refiner's blend stock; and the blend stock containing 16.2 percent methyl tertiary butyl ether. The ethanol and MTBE blends contained 3.0 percent oxygen by weight. Regulated emissions (total hydrocarbons, carbon monoxide, and oxides of nitrogen), detailed aldehydes, detailed hydrocarbons, ethanol, MTBE, benzene, and 1,3-butadiene were determined. The highest levels of regulated emissions were produced at the lower temperature. Blended fuels produced almost twice the evaporative hydrocarbon emissions at high temperatures as did the base fuels. Benzene emissions varied with fuels and operating temperatures, while 1,3-butadiene emissions decreased slightly with increasing temperatures. Formaldehyde emissions were not sensitive to fuel or temperature changes. Ethanol fuel blend total aldehyde emissions increased by 40 percent due to increased acetaldehyde emissions. Fuel blends had approximately a 3 percent economy decrease. The MTBE fuel blend appeared to offer the most reduction in total hydrocarbon, carbon monoxide, and oxides of nitrogen for the fuels and temperatures tested.     

Emissions of isoprene,monoterpene and short-chained carbonyl compounds from Eucalyptus spp. in southern Australia

Eucalypts are among the highest emitters of biogenic volatile organic compounds, yet there is relatively little data available from field studies of this genus. Emissions of isoprene, monoterpenes and the short-chained carbonyls formaldehyde, acetaldehyde and acetone were determined from four species (Eucalyptus camaldulensis, Eucalyptus globulus, Eucalyptus grandis, and Eucalytpus viminalis) in Australia. A smaller comparative study was conducted on E. camaldulensis in south-eastern Australia. Carbonyl emissions, reported here for the first time from eucalypts, were generally comparable with rates reported for other species, with diurnal emissions peaking at about 4, 75 and 34 nmol m^?2 min^?1 for acetone, formaldehyde and acetaldehyde respectively. There was wide variation in diurnal isoprene and monoterpene emissions between species, but under standard conditions, isoprene emissions were much lower than previous reports. Conversely, standard emission rates of monoterpenes were as much as six times greater than previous reports for some species. Emission of each carbonyl was correlated with its ambient concentration across different species, but more weakly related to temperature. Acetaldehyde emission in particular was significantly correlated with transpiration, but not with sap flow or with ethanol concentrations in xylem sap, suggesting fermentation within the leaf and stomatal conductance are primary controlling processes. Differences in acetaldehyde exchange velocities between sites, in addition to transpiration differences, suggest stomata may indeed exert long term emission regulation, in contrast to compounds for which no biological sink exists.     

Hazardous air pollutant emissions from gas-fired combustion sources: emissions and the effects of design and fuel type

Air emissions from gas-fired combustion devices such as boilers, process heaters, gas turbines and stationary reciprocating engines contain hazardous air pollutants (HAPs) subjected to consideration under the federal clean air act (CAA). This work presents a recently completed major research project to develop an understanding of HAP emissions from gas-fired boilers and process heaters and new HAP emission factors based on field emission tests of gas-fired external combustion devices used in the petroleum industry. The effect of combustion system design and operating parameters on HAP emissions determined by both field and research tests are discussed. Data from field tests of gas-fired petroleum industry boilers and heaters generally show very low emission levels of organic HAPs. A comparison of the emission data for boilers and process heaters, including units with and without various forms of NOx emission controls, showed no significant difference in organic HAP emission characteristics due to process or burner design. This conclusion is also supported by the results of research tests with different burner designs. Based on field tests of units fired with natural gas and various petroleum industry process gases and research tests in which gas composition was intentionally varied, organic HAP emissions were not determined to be significantly affected by the gas composition. Research data indicate that elevated organic HAP emission levels are found only under extreme operating conditions (starved air or high excess air combustion) associated with poor combustion.     

Primary sources of selected POPs: regional and global scale emission inventories

During the last decade, a number of studies have been devoted to the sources and emissions of Persistent Organic Pollutants (POPs) at regional and global scales. While significant improvements in knowledge have been achieved for some pesticides, the quantitative understanding of the emission processes and emission patterns for "non-pesticide" POPs are still considered limited. The key issues remaining for the non-pesticide POPs are in part determined by their general source classification. For industrial chemicals, such as the polychlorinated biphenyls (PCBs), there is considerable uncertainty with respect to the relative importance of atmospheric emissions from various source categories. For PCBs, temperature is discussed as a potential key factor influencing atmospheric emission levels and patterns. When it comes to the unintentional by-products of combustion and industrial processes (PCDD/Fs), there is still a large uncertainty with respect to the relative contribution of emissions from unregulated sources such as backyard barrel burning that requires further consideration and characterisation. For hexachlorobenzene (HCB), the relative importance of primary and secondary atmospheric emissions in controlling current atmospheric concentrations remains one of the key uncertainties. While these and other issues may remain unresolved, knowledge concerning the emissions of POPs is a prerequisite for any attempt to understand and predict the distribution and fate of these chemicals on a regional and global scale as well as to efficiently minimise future environmental burdens.     

Sources and photodecomposition of formaldehyde and acetaldehyde in Rome ambient air

Atmospheric levels of formaldehyde and acetaldehyde as well as their diurnal and seasonal variations were investigated from 1994 to 1997 in downtown Rome during sunny and wind calm days. Hourly concentrations of formaldehyde ranged from 8 to 28 ppbV in summer and 7 to 17 ppbv in winter; acetaldehyde concentrations varied correspondingly within the 3–18 and 2–7 ppbv intervals. Percentages of both aldehydes photochemically produced were estimated through a simple relationship based upon the comparison of individual ratios of formaldehyde and acetaldehyde to toluene in ambient air and automobile emission. Photochemical production was found to weigh upon atmospheric levels for 80–90% in summer days. It dropped below 35% in the winter period, when direct emission from traffic largely predominated. Photochemical summer source was more efficient for acetaldehyde than for formaldehyde, especially in the early morning. The importance of formaldehyde as the major source of hydroxyl radicals in Rome was also assessed.     

Updating the conceptual model for fine particle mass emissions from combustion systems

Atmospheric transformations determine the contribution of emissions from combustion systems to fine particulate matter (PM) mass. For example, combustion systems emit vapors that condense onto existing particles or form new particles as the emissions are cooled and diluted. Upon entering the atmosphere, emissions are exposed to atmospheric oxidants and sunlight, which causes them to evolve chemically and physically, generating secondary PM. This review discusses these transformations, focusing on organic PM. Organic PM emissions are semi-volatile at atmospheric conditions and thus their partitioning varies continuously with changing temperature and concentration. Because organics contribute a large portion of the PM mass emitted by most combustion sources, these emissions cannot be represented using a traditional, static emission factor. Instead, knowledge of the volatility distribution of emissions is required to explicitly account for changes in gas-particle partitioning. This requires updating how PM emissions from combustion systems are measured and simulated from combustion systems. Secondary PM production often greatly exceeds the direct or primary PM emissions; therefore, secondary PM must be included in any assessment of the contribution of combustion systems to ambient PM concentrations. Low-volatility organic vapors emitted by combustion systems appear to be very important secondary PM precursors that are poorly accounted for in inventories and models. The review concludes by discussing the implications that the dynamic nature of these PM emissions have on source testing for emission inventory development and regulatory purposes. This discussion highlights important linkages between primary and secondary PM, which could lead to simplified certification test procedures while capturing the emission components that contribute most to atmospheric PM mass.     

Is tree growth reduction related to direct foliar injuries or soil chemistry modifications?

In the context of intense emissions causing atmospheric pollution, tree growth reductions could be related to soil chemistry modifications or direct foliar injuries. To verify these hypotheses, mineral soils were sampled in an area (Murdochville, Canada) where previous studies had demonstrated that tree growth was impacted by smelter emissions and that forest floor lead concentrations could be used as a proxy for atmospheric pollutant depositions. Samples were analysed for Al, Pb (concentrations and isotope ratios), basic cations (Ca, K, P, and Mg) and Zr. Mass balance calculations were performed on soil profiles to assess vertical migration of elements. Pb concentrations in litter diminished gradually with distance from the smelter. The Pb isotope ratios in these organic soil layers were close to those measured in the Murdochville ores. These patterns were not encountered in mineral soil layers. Pb isotope ratios in these layers were close to those measured in uncontaminated geological materials, and Pb concentrations and basic cation depletions were not related to the proximity of the smelter. Growth reduction was closely associated with litter Pb concentrations, which were used as a proxy for atmospheric deposition, but was not correlated with any elemental concentration or cation depletion measured in mineral soil layers. Our overall results suggest that trees responded mainly to direct atmospheric emissions, which caused foliar damage, rather than to soil chemistry modifications.     

Emission Characteristics of Mexico City Vehicles

The University of Denver remote sensor for automobile exhaust was set up for nine days at five locations in the Mexico City area. A total of 31,838 valid readings for CO and HC emissions were obtained. The emissions distribution was unlike any other we have observed in North America or Europe, in that the emissions for both CO and HC were vastly greater than seen elsewhere. The readings are discussed in terms of the fraction of CO and HC which would be measured by a tailpipe probe, and in terms of grams emitted per gallon of gasoline. The median CO emission was 3.8 percent, with half of the CO emissions coming from the 24 percent of the fleet with over 6.6 percent CO in the exhaust. The median HC emission was 1,100 parts per million measured as propane equivalent, while half the emissions come from twelve percent of the fleet with more than 4,000 ppm propane equivalent in the exhaust.     

Comparison of emissions estimates derived from atmospheric measurements with national estimates of HFCs,PFCs and SF6

This paper assesses the feasibility of using atmospheric measurement of fluorinated greenhouse gases (HFCs, PFCs and SF6) for the review and verification of greenhouse gas inventories provided by national governments. For this purpose, available data were compiled. It was found that atmospheric measurements of these gases are available and provide an indication of global annual emissions with sufficient certainty to reach the following conclusions: Within the uncertainty of the method, it was found that emissions of HFC-23, a by-product of HCFC-22 production, as obtained from atmospheric measurements did not decrease as fast, as the countries have reported. In contrast, SF6 concentrations in the atmosphere suggest higher emissions than reported by countries. Regional emission estimates from atmospheric measurements are still in a more pioneering state and cannot be compared to national estimates. Intensified efforts to measure HFCs, PFCs and SF6 in the atmosphere are recommended.     

Hazardous air pollutants in industrial area of Mumbai - India

Hazardous Air Pollutants (HAPs) have a potential to be distributed into different component of environment with varying persistence. In the current study fourteen HAPs have been quantified in the air using TO-17 method in an industrial area of Mumbai. The distribution of these HAPs in different environmental compartments have been calculated using multi media mass balance model, TaPL3, along with long range transport potential and persistence. Results show that most of the target compounds partition mostly in air. Phenol and trifluralin, partition predominantly into soil while ethyl benzene and xylene partition predominantly into vegetation compartment. Naphthalene has the highest persistence followed by ethyl benzene, xylene and 1,1,1 trihloro ethane. Long range transport potential is maximum for 1,1,1 trichloroethane. Assessment of human health risk in terms of non-carcinogenic hazard and carcinogenic risk due to exposure to HAPs. have been estimated for industrial workers and residents in the study area considering all possible exposure routes using the output from TaPL3 model. The overall carcinogenic risk for residents and workers are estimated as high as unity along with very high hazard potential.