Characterization of On-Road Vehicle NO Emissions by a TILDAS Remote Sensor

ABSTRACT

A tunable infrared laser differential absorption spectrometer (TILDAS) was used to remotely sense the nitric oxide (NO) emissions from 1,473 on-road vehicles. The real-world measurement precision of this instrument in the limit of low NO concentration is 5 ppm of the vehicle exhaust, which corresponds to a 3o detection limit of 15 ppm. Our analysis of the distribution of negative concentration measurements produced during this experiment supports this claim, showing that the instrumental noise for this set of measurements was at most 8 ppm in the limit of low NO concentration. The high sensitivity of this instrument allowed us to measure the NO emissions of even the cleanest vehicles. The measured vehicle fleet NO emissions closely fit a gamma distribution with 10% of the fleet contributing about 50% of the total fleet emissions. Newer vehicles had lower NO emissions than older ones, but high NO emitters were found in every vehicle age cohort. On a vehicle-by-vehicle basis, NO emissions correlated very weakly with vehicle velocity, acceleration, power per unit mass, carbon monoxide (CO) emissions, and hydrocarbon (HC) emissions. High NO emitting vehicles could not be identified by remote sensing of CO or HC emissions and vice versa. When we compared the NO emissions for 117 vehicles measured more than one time, about half of the high NO emitters were found to be very consistent, while the other half varied significantly.     

Multispecies remote sensing measurements of vehicle emissions on Sherman Way in Van Nuys,California

As part of the 2010 Van Nuys tunnel study, researchers from the University of Denver measured on-road fuel-specific light-duty vehicle emissions from nearly 13,000 vehicles on Sherman Way (0.4 miles west of the tunnel) in Van Nuys, California, with its multispecies Fuel Efficiency Automobile Test (FEAT) remote sensor a week ahead of the tunnel measurements. The remote sensing mean gram per kilogram carbon monoxide (CO), hydrocarbon (HC), and oxide of nitrogen (NO_x) measurements are 8.9% lower, 41% higher, and 24% higher than the tunnel measurements, respectively. The remote sensing CO/NO_x and HC/NO_x mass ratios are 28% lower and 20% higher than the comparable tunnel ratios. Comparisons with the historical tunnel measurements show large reductions in CO, HC, and NO_x over the past 23 yr, but little change in the HC/NO_x mass ratio since 1995. The fleet CO and HC emissions are increasingly dominated by a few gross emitters, with more than a third of the total emissions being contributed by less than 1% of the fleet. An example of this is a 1995 vehicle measured three times with an average HC emission of 419 g/kg fuel (two-stroke snowmobiles average 475 g/kg fuel), responsible for 4% of the total HC emissions. The 2008 economic downturn dramatically reduced the number of new vehicles entering the fleet, leading to an age increase (>1 model year) of the Sherman Way fleet that has increased the fleet's ammonia (NH₃) emissions. The mean NH₃ levels appear little changed from previous measurements collected in the Van Nuys tunnel in 1993. Comparisons between weekday and weekend data show few fleet differences, although the fraction of light-duty diesel vehicles decreased from the weekday (1.7%) to Saturday (1.2%) and Sunday (0.6%).

Implications: On-road remote sensing emission measurements of light-duty vehicles on Sherman Way in Van Nuys, California, show large historical emission reductions for CO and HC emissions despite an older fleet arising from the 2008 economic downturn. Fleet CO and HC emissions are increasingly dominated by a few gross emitters, with a single 1995 vehicle measured being responsible for 4% of the entire fleet's HC emissions. Finding and repairing and/or scrapping as little as 2% of the fleet would reduce on-road tailpipe emissions by as much as 50%. Ammonia emissions have locally increased with the increasing fleet age.     

On-road remote sensing measurements and fuel-based motor vehicle emission inventory in Hangzhou,China

Motor vehicles are one of the largest sources of air pollutants worldwide. Despite their importance, motor vehicle emissions are inadequately understood and quantified, esp. in developing countries. In this study, the real-world emissions of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NO) were measured using an on-road remote sensing system at five sites in Hangzhou, China in 2004 and 2005. Average emission factors of CO, HC and NO_x for petrol vehicles of different model year, technology class and vehicle type were calculated in grams of pollutant per unit of fuel use (g l⁻¹) from approximately 32,260 petrol vehicles. Because the availability of data used in traditional on-road mobile source estimation methodologies is limited in China, fuel-based approach was implemented to estimate motor vehicle emissions using fuel sales as a measure of vehicle activity, and exhaust emissions factors from remote sensing measurements. The fuel-based exhaust emission inventories were also compared with the results from the recent international vehicle emission (IVE) model. Results show that petrol vehicle fleet in Hangzhou has significantly high CO emissions, relatively high HC and low NO_x, with the average emission factors of 193.07±15.63, 9.51±2.40 and 5.53±0.48 g l⁻¹, respectively. For year 2005 petrol vehicles exhaust emissions contributed with 182,013±16,936, 9107±2255 and 5050±480 metric ton yr⁻¹ of CO, HC and NO_x, respectively. The inventories are 45.5% higher, 6.6% higher and 53.7% lower for CO, HC and NO_x, respectively, than the estimates using IVE travel-based model. In addition, a number of insights about the emission distributions and formation mechanisms have been obtained from an in-depth analysis of these results.     

Effect of methyl tertiary butyl ether concentrations on exhaust emissions from gasoline used in the metropolitan area of Mexico City

In this work, the primary objective was to assess the impact of oxygenated fuel on the exhaust emissions from an important fraction of vehicles in the Metropolitan Area of Mexico City (MAMC). The results aim to provide information on the actual effect of MTBE on a fleet that represents more than 60% of the in-use vehicles in the MAMC. Ten vehicles were tested with a low-octane base gasoline, and 10 more with a regular-grade unleaded base gasoline. Three MTBE concentrations, 5, 10, and 15 vol %, were tested following the U.S. Federal Test Procedure (FTP). CO, total HC, and NOx from the exhaust gases were quantitatively evaluated and also characterized for FTP speciated organic emissions. From this data, the O3-forming potential of the fuels was calculated. Results show that for the fleet using low-octane gasoline, the addition of 10% MTBE substantially reduced CO emissions, but total HC concentration in the exhaust showed a modest decrease. For the regular gasoline, the 10% MTBE blend seemed to be the best choice, but there was not a significant decrease in emissions. The specific reactivity of each fuel, expressed in grams of O3 per gram of nonmethane organic gases, increased with MTBE concentration in both cases. This result is important to consider, especially for a region like Mexico City, which has high atmospheric O3 concentrations.     

Prospects of inspection and maintenance of two-wheelers in India.

Two-wheeler vehicles in Delhi, India--roughly 70% of the total vehicle fleet--are responsible for a significant portion of the city's vehicle emissions and petroleum consumption. An inspection and maintenance (I/M) program that ensures vehicle emission control systems are well maintained can complement other emission reduction strategies. This paper presents the initial findings of extensive data collected on vehicle characteristics and emissions for two-wheeler vehicles operating in Delhi in a series of I/M camps conducted by the Society of Indian Automobile Manufacturers and various partners in late 1999. The analysis shows idle HC and CO emissions [measured in terms of parts per million (ppm) and volume % (vol %), respectively] in a slow declining trend with subsequent model years, reflecting tighter emission standards and more advanced emission technologies. The I/M benefits--3 vol % and 39% reduction in idle and mass CO, respectively; 40 vol % and 22% reduction in idle and mass HC, respectively; and a 10-20% increase in fuel efficiency--were higher than those reported in the literature. Although these benefits are substantial, any implementation strategy needs to consider cost-effectiveness. In the present study, only 10% of vehicles--contributing 22% of the total vehicle emissions--failed the idle CO standard. Fleet emissions data variability necessitates a large sample size to develop a baseline for the vehicle fleet, but a smaller, scientifically designed sample and better data collection quality could periodically track the benefits at future camps.     

The Formation of Mg3Ca(S04)4 during the Sulfation Reaction of Dolomite

Abstract

Inspection and maintenance programs for motor vehicles in the United States increasingly use loaded mode mass emissions testing (IM240). A method was developed to predict mass emission rates and mass emission changes, particularly from repair benefits, using a low-cost, portable four-gas non-dispersive infrared (NDIR) vehicle exhaust gas analyzer. A single vehicle was tested several times with the analyzer while on the dynamometer and undergoing successive repairs. Excellent correlations for CO and HC were observed. Five vehicles were measured using an on-road driving loop before and after emissions-related repairs, while another three vehicles were tested with no repairs performed. The on-road concentration data used to guide the repair process were converted to grams per gallon; when divided by estimated miles per gallon, this gave grams per mile emissions for comparison to IM240. Correlation coefficients (r²) of 0.87 for CO and 0.76 for HC were achieved for the 13 tests. The linear correlations between IM240 and emissions measured by this method would allow repair facilities to perform a relatively inexpensive test for diagnostic purposes and to estimate repair effectiveness without the need for a dynamometer.     

Automotive Exhaust Emission Levels by Geographic Area and Vehicle Make A Nationwide Survey

Gross average automotive exhaust emissions data collected by the Atlantic Richfield Clean Air Caravan during the summer of 1970 showed only slight geographical variations when the specific makes were ignored. When considering specific makes, significant differences were found on an average emissions basis. Vehicle population—emission distributions showed wide variations in the 50% population levels and in the percent of vehicles with emissions greater than specified values. Hydrocarbon (HC) and carbon monoxide (CO) data are given on a gross basis for the 1970, 1968-69, 1966-67, and pre-1966 model year group vehicles. Average HC and CO emissions and vehicle population-Idle emissions distribution curves are included for specific make vehicles in selected areas.     

用空气加热器减少轻型汽油车低温冷启动时HC、CO 排放量的研究

按照《轻型汽车污染物排放限值及测量方法(中国Ⅲ、Ⅳ阶段)》(GB 18352.3-2005)的测试规范,在一辆轻型汽油车上使用空气加热器进行发动机进气预热,并测定了车辆低温冷启动时的HC、CO排放量.结果表明,发动机启动后24 s左右,HC的瞬态排放量达到最大值,HC的排放主要集中在启动后的前150 s左右；发动机启动...     

On-Road,In-Use Gaseous Emission Measurements by Remote Sensing of School Buses Equipped with Diesel Oxidation Catalysts and Diesel Particulate Filters

Abstract

A remote sensing device was used to obtain on-road and in-use gaseous emission measurements from three fleets of schools buses at two locations in Washington State. This paper reports each fleet’s carbon monoxide (CO), hydrocarbon (HC), nitric oxide (NO), and nitrogen dioxide (NO₂) mean data. The fleets represent current emission retrofit technologies, such as diesel particulate filters and diesel oxidation catalysts, and a control fleet. This study shows that CO and HC emissions decrease with the use of either retrofit technology when compared with control buses of the same initial emission standards. The CO and HC emission reductions are consistent with published U.S. Environmental Protection Agency verified values. The total oxides of nitrogen (NO_x), NO, and the NO₂/NO_x ratio all increase with each retrofit technology when compared with control buses. As was expected, the diesel particulate filters emitted significantly higher levels of NO₂ than the control fleet because of the intentional conversion of NO to NO₂ by these systems. Most prior research suggests that NO_x emissions are unaffected by the retrofits; however, these previous studies have not included measurements from retrofit devices on-road and after nearly 5 yr of use. Two 2006 model-year buses were also measured. These vehicles did not have retrofit devices but were built to more stringent new engine standards. Reductions in HCs and NO_x were observed for these 2006 vehicles in comparison to other non-retrofit earlier model-year vehicles.     

A Multipurpose Flare Stack for Control of Chemical Process Wastes

Abstract

To test the effectiveness of California’s vehicle inspection/ maintenance (I/M) program, exclusive of vehicle-owner intervention, a fleet of more than 1,100 vehicles that previously had failed California’s Smog Check test were sent to randomly selected Smog Check stations in the Los Angeles area for covert inspections and repairs. The two-speed idle test was used for repairs. For those vehicles that were repaired at the first inspection, their FTP emission reductions were 25%, 14%, and 11% for hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NO_x), respectively, although emissions testing for NO_x was not performed at the Smog Check stations. Idle HC and CO emissions increased for 35% and 43% of the vehicles, respectively, after repairs. This data set shows that most vehicles that fail the Smog Check inspection are only marginal emitters, with 61% and 44% of the total potential for HC and CO emission reductions, respectively, coming from only 10% of the vehicles that currently fail the inspection. When the vehicles were rank-ordered by idle emissions from dirtiest to cleanest, emission reduction costs for the highest-emitting 10% of the fleet averaged $l,100/ton and $250/ton for HC and CO, respectively, attributing all the costs to each pollutant exclusively. For the remaining vehicles, costs increased dramatically.     

Emissions profile from new and in-use handheld, 2-stroke engines

The objective of this study was to characterize exhaust emissions from a series of handheld, 2-stroke small engines. A total of 23 new and used engines from model years 1981–2003 were studied; these engines spanned three phases of emission control (pre-control, phase-1, phase-2). Measured emissions included carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x), hydrocarbons (HC), fine particulate matter (PM_2.5), and sulfur dioxide (SO₂). Emissions reductions in CO (78%) and HC (52%) were significant between pre-control and phase-2 engines. These reductions can be attributed to improvements in engine design, reduced scavenging losses, and implementation of catalytic exhaust control. Total hydrocarbon emissions were strongly correlated with fuel consumption rates, indicating varying degrees of scavenging losses during the intake/exhaust stroke. The use of a reformulated gasoline containing 10% ethanol resulted in a 15% decrease in HC and a 29% decrease in CO emissions, on average. Increasing oil content of 2-stroke engine fuels results in a substantial increase of PM_2.5 emissions as well as smaller increases in HC and CO emissions. Results from this study enhance existing emission inventories and appear to validate predicted improvements to ambient air quality through implementation of new phase-2 handheld emission standards.     

Estimations of real-world N2O emissions from road vehicles by means of measurements in a traffic tunnel

Ambient air measurements of N2O, NOx, CO, and HC based on grab sampling were conducted in a major traffic tunnel in Sweden, that carries up to 4,000 vehicles per hour, in order to estimate real-world emissions of N2O for road traffic. Two different methods--relative and mass balance-were used to calculate a N2O emission factor for the mixed vehicle fleet, which gave an average emission factor, at average speeds of 30-70 km/h, of approximately 25 mg N2O/ km, with a range of 7-56 mg/km.     

Ammonia emissions from a representative in-use fleet of light and medium-duty vehicles in the California South Coast Air Basin

We used Fourier Transform Infrared Spectroscopy (FTIR) to measure tailpipe ammonia emissions from a representative fleet of 41 light and medium-duty vehicles recruited in the California South Coast Air Basin. A total of 121 chassis dynamometer emissions tests were conducted on these vehicles and the test results were examined to determine the effects of several key variables on ammonia emissions. Variables included vehicle type, driving cycle, emissions technology, ammonia precursor emissions (i.e. CO and NOx) and odometer readings/model year as a proxy for catalyst age. The mean ammonia emissions factor was 46 mg km^?1 (σ = 48 mg km^?1) for the vehicle fleet. Average emission factors for specific vehicle groups are also reported in this study. Results of this study suggest vehicles with the highest ammonia emission rates possess the following characteristics: medium-duty vehicles, older emissions technologies, mid-range odometer readings, and higher CO emissions. In addition, vehicles subjected to aggressive driving conditions are likely to be higher ammonia emitters. Since the vehicles we studied were representative of recent model year vehicles and technologies in urban airsheds, the results of our study will be useful for developing ammonia emissions inventories in Los Angeles and other urban areas where California-certified vehicles are driven. However, efforts should also be made to continue emissions testing on in-use vehicles to ensure greater confidence in the ammonia emission factors reported here.     

Idle emissions from heavy-duty diesel and natural gas vehicles at high altitude

Idle emissions of total hydrocarbon (THC), CO, NOx, and particulate matter (PM) were measured from 24 heavy-duty diesel-fueled (12 trucks and 12 buses) and 4 heavy-duty compressed natural gas (CNG)-fueled vehicles. The volatile organic fraction (VOF) of PM and aldehyde emissions were also measured for many of the diesel vehicles. Experiments were conducted at 1609 m above sea level using a full exhaust flow dilution tunnel method identical to that used for heavy-duty engine Federal Test Procedure (FTP) testing. Diesel trucks averaged 0.170 g/min THC, 1.183 g/min CO, 1.416 g/min NOx, and 0.030 g/min PM. Diesel buses averaged 0.137 g/min THC, 1.326 g/min CO, 2.015 g/min NOx, and 0.048 g/min PM. Results are compared to idle emission factors from the MOBILE5 and PART5 inventory models. The models significantly (45-75%) overestimate emissions of THC and CO in comparison with results measured from the fleet of vehicles examined in this study. Measured NOx emissions were significantly higher (30-100%) than model predictions. For the pre-1999 (pre-consent decree) truck engines examined in this study, idle NOx emissions increased with model year with a linear fit (r2 = 0.6). PART5 nationwide fleet average emissions are within 1 order of magnitude of emissions for the group of vehicles tested in this study. Aldehyde emissions for bus idling averaged 6 mg/min. The VOF averaged 19% of total PM for buses and 49% for trucks. CNG vehicle idle emissions averaged 1.435 g/min for THC, 1.119 g/min for CO, 0.267 g/min for NOx, and 0.003 g/min for PM. The g/min PM emissions are only a small fraction of g/min PM emissions during vehicle driving. However, idle emissions of NOx, CO, and THC are significant in comparison with driving emissions.     

Bioethanol-gasoline fuel blends: exhaust emissions and morphological characterization of particulate from a moped engine

This study was aimed at evaluating the effects of gasoline-ethanol blends on the exhaust emissions in a catalyst-equipped four-stroke moped engine. The ethanol was blended with unleaded gasoline in at percentages (10, 15, and 20% v/v). The regulated pollutants and the particulate matter emissions were evaluated over the European ECE R47 driving cycle on the chassis dynamometer bench. Particulate matter was characterized in terms of total mass collected on filters and total number ofparticles in the range 7 nm-10 microm measured by electrical low-pressure impactor (ELPI). In addition, particle-phase polycyclic aromatic hydrocarbons (PAHs) emissions were evaluated to assess the health impact of the emitted particulate. Finally, an accurate morphological analysis was performed on the particulate by high-resolution transmission electron microscope (TEM) equipped with a digital image-processing/data-acquisition system. In general, CO emission reductions of 60-70% were obtained with 15 and 20% v/v ethanol blends, while the ethanol use did not reduce hydrocarbon (HC) and NOx emissions. No evident effect of ethanol on the particulate mass emissions and associated PAHs emissions was observed. Twenty-one PAHs were quantified in the particulate phase with emissions ranging from 26 to 35 microg/km and benzo[a]pyrene equivalent (BaPeq) emission factors from 2.2 to 4.1 microg/km. Both particulate matter and associated PAHs with higher carcinogenic risk were mainly emitted in the submicrometer size range (<0.1 microm). On the basis of the TEM observations, no relevant effect of the ethanol use on the particulate morphology was evidenced, showing aggregates composed ofprimary particles with mean diameters in the range 17.5-32.5 nm.     

大型城市客车加速模拟工况排放特性的实验研究

通过对258辆大型城市客车进行加速模拟工况排放测试,研究了城市客车的排放特性,比较了压缩天然气(CNG)车辆与汽油车辆的排放特性,分析了车辆车龄与排放的关系、发动机燃油供给方式与排放的关系,以及车辆总质量与排放的关系。研究结果表明：燃用CNG的车辆其CO、NOx排放较汽油低许多,尤其是CO,但HC排放较汽油高;电喷车辆的CO、NOx排放比化油器车低,但HC排放值高于化油器车;车龄增长,车辆的CO、NOx排放值增大,但HC变化不明显;车辆总质量增加,排放呈下降趋势。     

Airshed Model Evaluation of Reactivity Adjustment Factors Calculated with the Maximum Incremental Reactivity Scale for Transitional-Low Emission Vehicles

Abstract

The California Air Resources Board recently adopted regulations for light- and medium-duty vehicles that require reductions in the ozone-forming potential or “reactivity,” rather than the mass, of nonmethane organic gas (NMOG) emissions. The regulations allow sale of all alternatively fueled vehicles (AFVs) that meet NMOG exhaust emission standards equivalent in reactivity to those set for vehicles fueled with conventional gasoline. Reactivity adjustment factors (RAFs), the ratio of the reactivity (per gram) of the AFV exhaust to that of the conventionally fueled vehicle (CFV), are used to correct the stringent exhaust emission standards. Complete chemical speciation of the exhaust and conversion of each NMOG species to an appropriate mass of ozone using the maximum incremental reactivity (MIR) scale of Carter determines the RAF. The MIR approach defines reactivity where NMOG control is the most effective strategy in reducing ozone concentrations, and assumes it is not important to define reactivity at other conditions, i.e., where NO_x is the limiting precursor.

This study used the Carnegie/California Institute of Technology airshed model to evaluate whether the RAF-adjusted AFV emissions result in ozone impacts equivalent to those of CFV emissions. A matrix of two ozone episodes in the South Coast Air Basin (SoCAB) of California, two base emission inventories, and exhaust emissions from three alternative fuels that meet the first level of the low emission vehicle standards bounds the expected range of conditions. Although very good agreement was found previously for individual NMOG species,² this study noted deviations of up to ±15 percent from the equal ozone impacts for any vehicle/fuel combination required by the California regulations. These deviations appear to be attributable to differences in spatial and temporal patterns of emissions between vehicle fleets, rather than a problem with the MIR approach. The first formally adopted RAF, a value of 0.41 for 85 percent methanol/15 percent gasoline-fueled vehicles, includes a 10 percent increase based on the airshed modeling. The correction to the RAF is different for other fuels and may be different for air basins other than the SoCAB.     

A Fuel-Based Motor Vehicle Emission Inventory

Abstract

A fuel-based methodology for calculating motor vehicle emission inventories is presented. In the fuel-based method, emission factors are normalized to fuel consumption and expressed as grams of pollutant emitted per gallon of gasoline burned. Fleet-average emission factors are calculated from the measured on-road emissions of a large, random sample of vehicles. Gasoline use is known at the state level from sales tax data, and may be disaggregated to individual air basins. A fuel-based motor vehicle CO inventory was calculated for the South Coast Air Basin in California for summer 1991. Emission factors were calculated from remote sensing measurements of more than 70,000 in-use vehicles. Stabilized exhaust emissions of CO were estimated to be 4400 tons/day for cars and 1500 tons/day for light-duty and medium- duty trucks, with an estimated uncertainty of ±20% for cars and ±30% for trucks. Total motor vehicle CO emissions, including incremental start emissions and emissions from heavy-duty vehicles were estimated to be 7900 tons/day. Fuelbased inventory estimates were greater than those of California's MVEI 7F model by factors of 2.2 for cars and 2.6 for trucks. A draft version of California's MVEI 7G model, which includes increased contributions from high-emitting vehicles and off-cycle emissions, predicted CO emissions which closely matched the fuel-based inventory. An analysis of CO mass emissions as a function of vehicle age revealed that cars and trucks which were ten or more years old were responsible for 58% of stabilized exhaust CO emissions from all cars and trucks.     

Estimations of Real-World N2O Emissions from Road Vehicles by Means of Measurements in a Traffic Tunnel

Abstract

Ambient air measurements of N₂O, NO_x, CO, and HC based on grab sampling were conducted in a major traffic tunnel in Sweden, that carries up to 4,000 vehicles per hour, in order to estimate real-world emissions of N₂O for road traffic. Two different methods—relative and mass balance—were used to calculate a N₂O emission factor for the mixed vehicle fleet, which gave an average emission factor, at average speeds of 30-70 km/h, of approximately 25 mg N₂O/ km, with a range of 7-56 mg/km.     

Product Guide/1970

Abstract

In Mexico City, the use and composition of fuels determine that carbon monoxide (CO) comes mostly from mobile sources, and sulfur dioxide (SO₂) from fixed and mobile sources. By simultaneously measuring hydrocarbons (HC), CO, and SO₂ in the atmosphere of Mexico City, the relative amounts coming from different sources can be estimated. Assuming that some HC are emitted proportionally to CO emissions, we can establish that [HC]₁= m1? [CO], where the proportionality constant ml corresponds to the ratio of emissions factor for HC and CO in mobile sources. Similarly for fuels containing sulfur, it can be assumed that [HC]₂ = m2 ? [SO₂]. In this way, the total HC are [HC]_total=[HC]₀+ ml ? [CO]+ m2 ? [SO₂], where [HC]₀ corresponds mainly to other sources like solvent evaporation, gas consumption, and natural emissions. In this way, it can be estimated that in Mexico City 75% of average HC comes from mobile sources, 5% from sulfur-related sources, and 19% from natural sources and solvent evaporation. Compared with the HC/CO ratio measured in the exhaust pipe of vehicles, we estimated that 70% of HC emitted from mobile sources are evaporative losses, and only 30% come through the exhaust system.