MnO2对煤粉中CaO固硫效率影响机理

采用热力学计算和实验方法对钙硫比n（CaO）/n（S）=2.0条件下不同钙基固硫剂的固硫效果进行了比较,发现：CaO的固硫效率最高。以CaO为固硫剂,研究了添加剂MnO2对CaO固硫效果的影响。结果表明,加入MnO2可以提高CaO的固硫效率,且其含量为1%时对CaO固硫的促进效果最佳。这是因为煤粉燃烧过程中MnO2将逐级分解,分解产物依次为Mn2O3和Mn3O4,锰的氧化物一方面可以催化CaO的固硫反应,另一方面,Mn3O4本身也参与到固硫反应之中,生成MnSO4,从而促进钙基固硫剂的固硫效果。     

复合固硫剂对型煤固硫的影响研究

固硫型煤作为煤燃烧中脱硫的一种重要方法，在燃煤SO2的减排方面起着重要的作用。为了考察固硫剂和固硫添加剂对型煤固硫及其对型煤燃烧释放SO2的规律的影响，对利用氧化镁和氧化钙为固硫剂，以煤矸石和粉煤灰为固硫添加剂进行了研究，同时通过XRD和SEM表征，进一步探讨了固硫剂及添加剂的固硫作用和机理。研究结果表明：(1)CaO...     

钙基脱硫剂高温固硫性能的影响因素试验分析

对含硫量为1．51％的大同煤，在不同的气氛和工况下加入钙基脱硫剂，并辅以添加剂，在800—1200℃的高温下开展了较为系统的试验和分析。与CaCO3和CaO相比，Ca（OH）2具有更好的高温固硫性能；Ca（OH）2、CaCO3和CaO在900℃左右均表现出很好的固硫率；氧化气氛较适用于1000℃以下固硫；高温取Ca／S比为2．0～2．5时较适合；按一定比例添加Fe2O3、SiO2和Al2O3配置的复合脱硫剂脱硫效率更高（试验值66．67％），复合添加剂能提高1000℃以上的固硫率，加宽了最佳固硫温度范围，且能维持比较稳定的高温固硫效果；不同条件下，CaSO4分解特性不同。     

己二酸和己二酸钠强化石灰石WFGD的对比研究

在湍球塔设备上进行了己二酸和己二酸钠强化石灰石WFGD的对比研究，考察了2种添加剂对脱硫过程的强化和缓冲作用，分析计算了2种添加剂对石灰石的利用率。实验结果表明，2种添加剂可以在较低浆液pH下维持较高脱硫率，并且2种添加剂均促进了CaCO₃的溶解，在相同条件下己二酸钠有更好的脱硫效果，而己二酸有更好的缓冲作用，且己二酸促进CaCO₃溶解的效果更显著。     

高铁酸盐对活性及分散染料的脱色研究

采用湿法制备了高铁酸钾(K₂FeO₄)氧化剂，研究了其对染料活性艳红X-3B(X-3B) 和分散蓝2BLN(2BLN)在不同pH条件下的脱色效果，并对Al₂ (SO₄)₃、K₂FeO₄及O₃对活性及分散染料的脱色效果进行了比较。结果表明：高铁酸钾对活性及分散染料的脱色效果明显， X-3B脱色率随pH的增加不断提高，2BLN脱色率在pH 6～10范围内无明显变化，在pH＝5时达到最大值。在X-3B及2BLN浓度同为100 mg／L，pH分别为10、5， K₂FeO₄浓度分别为100 mg／L和200 mg／L时，BLN及X-3B的脱色率分别达到92.3％和87.3％。在相同条件下，K₂FeO₄对活性艳红X-3B的脱色效果好于Al₂(SO₄)₃和O₃； 而K₂FeO₄对分散蓝2BLN的脱色效果虽比Al₂ (SO₄)₃稍差，但比臭氧的脱色效果要好。同时还研究了K₂FeO₄对活性及分散染料的脱色机理，结果表明： 高铁酸钾对X-3B的脱色依赖于K₂FeO₄的氧化作用，而对的2BLN的脱色则以絮凝为主。     

尿素/三乙醇胺吸收烟气NOx的实验研究

以尿素作为吸收液，与NO_x反应生成N₂和CO₂，脱除烟气中的氮氧化物。以一套双级串连的填料塔为主体反应器，分别对气速、液气比、反应物浓度、添加剂浓度和反应温度等参数对尿素溶液吸收NO_x反应的影响进行了实验研究，获得了优化实验工况，研究结果显示，在气速为0.1 m/s、液气比为16 L/m³、三乙醇胺为0.01%(质量比)、尿素浓度为13%（质量比）工况下, 反应温度为30~70℃，脱硝总效率可达50％以上，且随着NO_x体积分数增加而提高。     

可燃固废复合燃料的固硫固氯效果

以可燃垃圾、污水污泥和煤粉为原料,添加园林残余、固硫剂等按L16(45)正交表配料,采用机械成型设备制备固废复合燃料,研究燃料组分对固硫固氯效果的影响。固硫率、固氯率实验数据的极差、方差分析结果显示:CaO添加量对固硫率、固氯率的影响最显著;MnO2添加量对固氯率的影响仅次于CaO添加量,但对固硫率没有影响。运用ForStat 2.0统计软件建立了固硫率、固氯率指标的预测方程,置信度大于95%。应用综合评分法筛选出最佳固硫固氯效果的燃料制备配方为:A2B3C2D3,即垃圾、污泥、煤粉以2∶1∶1比例混合,园林残余为10%,助燃剂MnO2添加量为0.17%,固硫剂CaO添加1.2%时所制备的燃料,燃烧中固硫率可达74.55%,固氯率可达77.35%。     

新型转式垃圾焚烧过程中脱氯脱硫机理的研究

为了探讨有机垃圾焚烧过程钙基添加剂对HCl，SO_x生成特性的影响，分别在自行设计的中空水冷转式垃圾焚烧炉和固定床加热炉中进行了一系列的实验，研究结果表明新型转式焚烧炉具有强化传热传质特性，能提高HCl、SO_x的脱除率，可抑制有害气体的生成；同时也研究了 HCl，SO₂气体同时存在时，钙基添加剂对脱氯脱硫效率的影响规律。     

催化湿式氧化法处理高浓度唑螨酯生产废水的研究

对唑螨酯生产过程中产生的高浓度实际废水采用催化湿式氧化技术在鼓泡式固定床反应器连续反应装置上进行处理。实验表明，制备的复合负载型催化剂CuO-MnO₂-Cr₂O₃/ZrO₂-CeO₂在处理该废水时具有较好的催化活性。通过对反应温度、反应压力、反应空速、气液比和进水pH等工艺条件的考察，得出最佳的工艺条件为：反应温度=220℃，反应压力=5.8 MPa，空速＝1.8 h^-1，V（气）∶V（水）＝260∶1，进水pH＝9，在此条件下COD去除率达到95.2％。     

碳酸根对磷酸钙沉淀反应回收磷的影响简

以模拟的厌氧消化液为处理对象，通过小试实验，考察不同初始磷浓度C_P、Ca/P物质的量比、pH和温度下，碳酸根（CO₃^2-）对磷酸钙沉淀反应回收磷的影响；利用扫描电镜（SEM）、X射线衍射仪（XRD）和傅里叶变换红外光谱（FTIR）对沉淀产物进行表征。结果表明，高浓度的CO₃^2-对以磷酸钙沉淀反应去除和回收磷的效率影响较大；C_P相同时，CO₃^2-浓度（C_CO3^2-）越大，P的去除率越低，低C_P（20 mg/L）时尤为显著；当C_CO3^2-相同时，随着C_P的增大，反应速率加快，P的去除率逐渐升高，但升高幅度越来越小；增大Ca/P比和pH能提高P的去除率，降低CO₃^2-对磷酸钙沉淀反应的抑制作用，综合考虑实际效果，应选择Ca/P比为3.33，pH为9.0作为适宜的反应条件；升高温度对降低CO₃^2-对磷酸钙沉淀反应的抑制作用贡献不大。在C_P为60 mg/L，Ca/P比为1.67，pH为9.0，温度为20℃的条件下，当C _CO3^2-为0时，得到的沉淀产物主要为羟基磷灰石HAP；当C _CO3^2-为30 mmol/L时，得到的沉淀产物为磷酸钙和碳酸合磷灰石的混合物。     

贝壳粉型煤固硫剂固硫的实验及机理研究

以贝壳粉作为型煤固硫剂,用正交实验的方法研究了影响贝壳粉固硫率的主要影响因素,在高温(1 150℃)时固硫效率达到56.6%,比CaCO3的固硫率提高40%以上,具有较好的高温固硫性。分析得知,贝壳的主要成分为CaCO3,其含钙量在40%左右,贝壳中又含有较高的Na等碱金属元素以及Fe,Al和Si等。用X射线粉末衍射法分析了高温(1 150℃)型煤样生成的灰渣,分析了贝壳粉作为型煤固硫剂在高温下具有较高固硫率的机理。发现CaAlSi2O8为主的复合晶体在高温下包裹在CaSO4的表面,抑制了CaSO4的热分解从而有效地提高了固硫率。     

Suppression of Soot by Metal Additives During the Combustion of Polystyrene

This paper describes an experimental study on the suppression of soot by metal additives during the combustion of polystyrene (PS). A two-dimensional flame generated by using a Wolfhard-Parker type diffusion flame burner was used to simulate practical combustion situations. The PS was continuously fed to the burner and, by controlling the feed rate, the combustion was maintained at a steady state. The additives tested were the salts of Li, Na, K, Mg, Ca, Sr, and Ba, and the combinations of the salts of K and Ca, Sr, or Ba. These additives were added to the flame in the form of small drops of their aqueous solutions generated by an ultrasonic atomizer. Since the flow rate of the carrier gas (air) is very small, this addition causes no noticeable disturbance to the flame. The effectiveness of the alkali metals follows the order of their ease of ionization, i.e., K > Na > Li, and that of the alkaline-earth metals: Ba > Sr > Ca > Mg. At low addition rates, the effectiveness increases with increasing addition rate but becomes unaffected at high addition rates and the maximum percentage of soot suppressed is approximately 50 percent. The combinations of the two metals (i.e., K and Ca, Sr, or Ba) are much more effective than each single metal at the same addition rates and the maximum percentage of soot suppressed reaches approximately 90 percent. It is proposed that the alkaline-earth metals catalyze the ionization of the alkali metals, thus significantly enhancing the effect on soot suppression.     

Soot Control During the Combustion of Polystyrene

This paper describes an experimental study on the control of soot formation during the combustion of polystyrene (PS). A stable, twodimensional flame generated by using a Wolfhard-Parker type diffusion flame burner was used to simulate practical combustion situations. The combustion characteristics, effects of operating conditions on soot formation, and the effectiveness of various metallic additives as soot suppressants were investigated. It was found that soot yield could not be significantly reduced by controlling the oxidizer (air) flow rate. Increasing the O₂ mole fraction of the oxidlzer increased soot yield under typical operating conditions. However, soot yield could be greatly reduced by adding small amounts of air into the pyrolysis zone of the flame. The additional air would probably increase the combustion reaction rate while decreasing the soot precursor formation rate, thereby causing the observed effect. It was thus suggested that effective soot control could be accomplished by improving mixing between air and the PS devolatilizatlon products In practical combustion situations. The metallic additives tested in this study were the salts of Na, K, Ca, and Ba. Among these salts, Ca was the least effective in reducing soot, and K and Na were nearly equally effective. Ba was much more effective than all the others, and Its effectiveness was strongly dependent on its addition rate.     

The behaviour of phosphorus and heavy metals in sewage sludge ashes

The effect of the combustion atmosphere and the additives (CaO and HCl) on the behaviour of phosphorus and heavy metals during sewage sludge combustion was investigated. The results demonstrated that the reduction combustion promoted the vapourisation of phosphorus and heavy metals during sewage sludge combustion. Moreover, the concentrations of phosphorus and heavy metals in the bottom ash decreased with increasing HCl ratio, and the addition of CaO can stabilise heavy metals and phosphorus. It was also observed that phosphorus and heavy metals increased with increasing CaO ratio. Lastly, the difference of the TG-DTA curves with and without additives is discussed.     

Analysis and discussion on formation and control of primary particulate matter generated from coal-fired power plants

Particulate matter (PM) has been becoming the principal urban pollutant in many major cities in China, and even all over the world. It is reported that the coal combustion process is one of the main sources of PM in the atmosphere. Therefore, an investigation of formation and emission of fine primary PM in coal combustion was conducted. First, the sources and classification of coal-fired primary PM were discussed; then their formation pathways during the coal combustion process were analyzed in detail. Accordingly, the emission control methods for fine particles generated from coal-fired power plants were put forward, and were classified as precombustion control, in-combustion control, and postcombustion control. Precombustion control refers to the processes for improving the coal quality before combustion, such as coal type selection and coal preparation. In-combustion control means to take measures for adjusting the combustion conditions and injection of additives during the combustion process to abate the formation of PM. Postcombustion control is the way that the fine PM are aggregated into larger ones by some agglomeration approaches and subsequently are removed by dust removal devices, or some high-performance modifications of conventional particle emission control devices (PECDs) can be taken for capturing fine particles. Finally, some general management suggestions are given for reducing fine PM emission in coal-fired power plants.

ImplicationsThe analysis and discussions of coal properties and its combustion process are critical to recognizing the formation and emission of the fine primary PM in combustion. The measures of precombustion, in-combustion, and postcombustion control based on the analysis and discussions are favorable for abating the PM emission. Practically, some measures of implementation do need the support of national policies, even needing to sacrifice economy to gain environmental profit, but this is the very time to execute these, and high-performance PECDs, especially novel devices, should be used for removing fine PM in flue gas.     

煤矸石微生物脱硫试验研究

采用本试验室自主分离筛选出的氧化硫硫杆菌,通过煤矸石浸泡的微生物脱硫和煤矸石柱状淋洗的微生物脱硫试验,研究该菌株对大武口高硫煤矸石的脱硫效果.煤矸石浸泡试验表明,微生物对煤矸石脱硫效果明显,浸泡煤矸石2 h后脱硫量达0.79 g/L,脱硫率达24.5%,21 d持续稳定升高,脱硫率达28.3%,为煤矸石的快速脱硫提供了技术支持.煤矸石柱状淋洗试验表明,前9 d是氧化硫硫杆菌脱硫的活跃期,该菌株有较高的氧化煤矸石的能力.     

对含不同添加剂的细水雾洗消氯气的实验研究

采用小尺度模拟实验，对含有NaOH、Ca（OH）2、Na2CO3、FeCl2等不同添加剂的细水雾和纯细水雾进行氯气洗消对比实验，系统比较了各种浓度的添加剂对洗消效率的影响。研究发现：含添加剂的细水雾克服了纯细水雾对氯气洗消效率不高、洗消不彻底等的不足，可以在较大程度上减少洗消剂用量和洗消时间。但添加剂的加入，却改变了细水雾的特性及理化性质等，因此需要根据实际的氯气泄漏情况，选择合适的洗消添加剂。     

Characteristics of fundamental combustion and NOx emission using various rank coals

Eight types of coals of different rank were selected and their fundamental combustion characteristics were examined along with the conversion of volatile nitrogen (N) to nitrogen oxides (NOx)/fuel N to NOx. The activation energy, onset temperature, and burnout temperature were obtained from the differential thermogravimetry curve and Arrhenius plot, which were derived through thermo-gravimetric analysis. In addition, to derive the combustion of volatile N to NOx/fuel N to NOx, the coal sample, which was pretreated at various temperatures, was burned, and the results were compared with previously derived fundamental combustion characteristics. The authors' experimental results confirmed that coal rank was highly correlated with the combustion of volatile N to NOx/fuel N to NOx.     

燃煤炉窑烟气净化工艺及其装置的研究

在实验测试基础上,对燃煤烟气喷钙水浴复合脱硫工艺及设备进行了研究.实验表明,采用喷钙水浴复合脱硫工艺较单一喷钙或水浴具有更高的脱硫效果,且喷入的碳酸钙可得到充分利用.此外,还对钙硫比、喷钙方向及喷管插入水深等影响脱硫效率的因素进行了测试分析.     

Size distribution and anthropogenic sources apportionment of airborne trace metals in Kanazawa, Japan

Aerosol samples were collected from Kanazawa, Japan to examine the size distribution of 12 elements and to identify the major sources of anthropogenic elements. Key emission sources were identified and, concentrations contributed from individual sources were estimated as well. Concentrations of elements V, Ca, Cd, Fe, Ba, Mg, Mn, Pb, Sr, Zn, Co and Cu in aerosols were determined with ICP-MS. The results showed that Ca, Mg, Sr, Mn, Co and Fe were mainly associated with coarse particles (>2.1 μm), primarily from natural sources. In contrast, the elements Zn, Ba, Cd, V, Pb and Cu dominated in fine aerosol particles (<2.1 μm), implying that the anthropogenic origin is the dominant source. Results of the factor analysis on elements with high EF_Crust values (>10) showed that emissions from waste combustion in incinerators, oil combustion (involving waste oil burning and oil combustion in both incinerators and electricity generation plants), as well as coal combustion in electricity generation plants were major contributors of anthropogenic metals in the ambient atmosphere in Kanazawa. Quantitatively estimated sum of mean concentrations of anthropogenic elements from the key sources were in good agreement with the observed values. Results of this study elucidate the need for making pollution control strategy in this area.