Bamboo–Fiber Filled High Density Polyethylene Composites: Effect of Coupling Treatment and Nanoclay

High density polyethylene (HDPE)/bamboo composites with different nanoclay and maleated polyethylene (MAPE) contents were fabricated by melt compounding. The compounding characteristics, clay dispersion, HDPE crystallization, and mechanical properties of the composites were studied. The equilibrium torque during compounding decreased with use of clay masterbatch and increased with the addition of MAPE. The X-ray diffraction (XRD) data showed that the clay was exfoliated only when 1% clay was added to pure HDPE without MAPE. For HDPE/bamboo systems, MAPE was necessary to achieve clay exfoliation. For pure HDPE system, both dynamic and static bending moduli increased, while impact strength decreased with increased clay loading. For the HDPE/bamboo fiber composites, tensile strength, bending modulus and strength were improved with the use of MAPE. The use of the clay in the system led to reduced mechanical properties. Techniques such as pre-coating fibers with clay–MAPE mixture are needed to enhance the synergetic effect of the clay and bamboo fiber on the composite properties in the future study.     

Study of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV)/Bamboo Pulp Fiber Composites: Effects of Nucleation Agent and Compatibilizer

In this study, poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV)/bamboo pulp fiber (BPF) composites were prepared by melt compounding and injection molding. The crystallization ability, tensile strength and modulus, flexural strength and modulus, and impact strength were found substantially increased by the addition of BPF. Tensile and flexural elongations were also moderately increased at low fiber contents (<20%). BPF demonstrated not only higher strength and modulus, but also higher failure strain than the PHBV8 matrix. Boron nitride (BN) was also investigated as a nucleation agent for PHBV8 and maleic anhydride grafted PHBV8 (MA-PHBV8) as a compatibilizer for the composite system. BN was found to increase the overall properties of the neat polymer and the composites due to refined crystalline structures. MA-PHBV8 improved polymer/fiber interactions and therefore resulted in increased strength and modulus. However, the toughness of the composites was substantially reduced due to the hindrance to fiber pullout, a major energy dissipation source during the composite deformation.     

Preliminary Study of Non-woven Composite: Effect of Needle Punching and Kenaf Fiber Loadings on Non-woven Thermoplastic Composites Prepared From Kenaf and Polypropylene Fiber

Non-woven composites were produced using kenaf (bast) fiber and polypropylene (PP) fiber. The effects of needle punching process, number of needle and kenaf fiber loadings on the properties of non-woven composite were studied. The aspect ratio of kenaf fiber was also measured in this study. The aspect ratio of most of kenaf fiber used was in the range of 200–400. The results indicated that the mechanical strength of the non-woven composite was significantly influenced by the percentage of kenaf fiber. This may due to the evenly mixed kenaf and PP fibers during carding process prior to the mechanical interlocking by needle punching process. The tensile strength, modulus and toughness were enhanced with the incorporation of carded and needle punched fibers. The number of needle used in needle punching process had a significant effect on the strength of the composite. This was evident in SEM micrograph where composite prepared from carded to needle punched non-woven web showed better wettability as compared to composite prepared from carded non-woven web only. However, no significant difference was observed in water absorption and thickness swelling tests for composites prepared with different number of needles.     

Mechanical Properties of Poly (Lactic Acid)/Hemp Fiber Composites Prepared with a Novel Method

This research dealt with a novel method of fabricating green composites with biodegradable poly (lactic acid) (PLA) and natural hemp fiber. The new preparation method was that hemp fibers were firstly blending-spun with a small amount of PLA fibers to form compound fiber pellets, and then the traditional twin-screw extruding and injection-molding method were applied for preparing the composites containing 10–40 wt% hemp fibers with PLA pellets and compound fiber pellets. This method was very effective to control the feeding and dispersing of fibers uniformly in the matrix thus much powerful for improving the mechanical properties. The tensile strength and modulus were improved by 39 and 92 %, respectively without a significant decrease in elongation at break, and the corresponding flexural strength and modulus of composites were also improved by 62 and 90 %, respectively, when the hemp fiber content was 40 wt%. The impact strength of composite with 20 wt% hemp fiber was improved nearly 68 % compared with the neat PLA. The application of the silane coupling agent promoted further the mechanical properties of composites attributed to the improvement of interaction between fiber and resin matrix.     

Comparison of Polylactic Acid/Kenaf and Polylactic Acid/Rise Husk Composites: The Influence of the Natural Fibers on the Mechanical, Thermal and Biodegradability Properties

This paper investigates and compares the performances of polylactic acid (PLA)/kenaf (PLA-K) and PLA/rice husk (PLA-RH) composites in terms of biodegradability, mechanical and thermal properties. Composites with natural fiber weight content of 20% with fiber sizes of less than 100 μm were produced for testing and characterization. A twin-screw extrusion was used to compound PLA and natural fibers, and extruded composites were injection molded to test samples. Flexural and Izod impact test, TGA, soil burial test and SEM were used to investigate properties. All results were compared to a pure PLA matrix sample. The flexural modulus of the PLA increased with the addition of natural fibers, while the flexural strength decreased. The highest impact strength (34 J m⁻¹), flexural modulus (4.5 GPa) and flexural strength (90 MPa) were obtained for the composite made of PLA/kenaf (PLA-K), which means kenaf natural fibers are potential to be used as an alternative filler to enhance mechanical properties. On the other hand PLA-RH composite exhibits lower mechanical properties. The impact strength of PLA has decreased when filled with natural fibers; this decrease is more pronounced in the PLA-RH composite. In terms of thermal stability it has been found that the addition of natural fibers decreased the thermal stability of virgin PLA and the decrement was more prominent in the PLA-RH composite. Biodegradability of the composites slightly increased and reached 1.2 and 0.8% for PLA-K and PLA-RH respectively for a period of 90 days. SEM micrographs showed poor interfacial between the polymer matrix and natural fibers.     

Analysis of Flax and Cotton Fiber Fabric Blends and Recycled Polyethylene Composites

Manufacturing composites with polymers and natural fibers has traditionally been performed using chopped fibers or a non-woven mat for reinforcement. Fibers from flax (Linum usitatissimum L.) are stiff and strong and can be processed into a yarn and then manufactured into a fabric for composite formation. Fabric directly impacts the composite because it contains various fiber types via fiber or yarn blending, fiber length is often longer due to requirements in yarn formation, and it controls the fiber alignment via weaving. Composites created with cotton and flax-containing commercial fabrics and recycled high-density polyethylene (HDPE) were evaluated for physical and mechanical properties. Flax fiber/recycled HDPE composites were easily prepared through compression molding using a textile preform. This method takes advantage of maintaining cotton and flax fiber lengths that are formed into a yarn (a continuous package of short fibers) and oriented in a bidirectional woven fabric. Fabrics were treated with maleic anhydride, silane, enzyme, or adding maleic anhydride grafted polyethylene (MAA-PE; MDEX 102-1, Exxelor^® VA 1840) to promote interactions between polymer and fibers. Straight and strong flax fibers present problems because they are not bound as tightly within yarns producing weaker and less elastic yarns that contain larger diameter variations. As the blend percentage and mass of flax fibers increases the fabric strength, and elongation generally decrease in value. Compared to recycled HDPE, mechanical properties of composite materials (containing biodegradable and renewable resources) demonstrated significant increases in tensile strength (1.4–3.2 times stronger) and modulus of elasticity (1.4–2.3 times larger). Additional research is needed to improve composite binding characteristics by allowing the stronger flax fibers in fabric to carry the composites load.     

Sustainable Use of Coffee Husks For Reinforcing Polyethylene Composites

The utilization of the coffee husk fiber (CHF) from the coffee industry as a reinforcing filler in the preparation of a cost-effective thermoplastic based composite was explored in this study. The chemical composition and thermal properties of the CHF were investigated and compared with those of wood fiber (WF). CHF proved to be mainly composed of cellulose, hemicellulose and lignin, and exhibited similar thermal behavior to WF. High density polyethylene (HDPE) composites with CHF loadings of from 40 to 70% were prepared using melt processing and extrusion. The processing properties, mechanical behavior, water absorption and thermal performance of these composites were investigated. The effect of maleated polyethylene (MAPE) used as a coupling agent on the composite was explored. The experimental results showed that increasing the CHF loading in the HDPE matrix resulted in an increase in the modulus and thermal properties of the composites, but resulted in poor water resistance. The addition of a 4% MAPE significantly improved the interfacial behavior of the hydrophilic lignocellulosic fiber and the hydrophobic polymer matrix.     

Effects of Incorporating Polycaprolactone and Flax Fiber into Glycerol-Plasticized Pea Starch

This study focused on improving the material properties of pea thermoplastic starch (TPS) with polycaprolactone (PCL) and flax fiber. Accordingly, composites of glycerol-plasticized pea starch, polycaprolactone, and flax fiber were prepared through solid-phase compounding and compression-molding. The specimens were characterized through scanning electron microscopy, tensile test, moisture absorption test, and differential scanning calorimetry. Morphological studies of the tensile fracture surfaces revealed poor TPS-PCL interfacial interaction and limited TPS-flax fiber interfacial bonding. The composites showed significant improvements in tensile strength with reduced moisture absorption capability essentially due to the hydrophobicity of PCL. Individual components of the composites retained their respective thermal properties, an indication of thermodynamic immiscibility.     

Effect of Surface Treatment on Betel Nut (Areca catechu) Fiber in Polypropylene Composite

Betel nut fiber (Bn)/polypropylene (PP) composites were prepared in the different ratio of 10:90, 20:80, 30:70, 40:60 (Bn wt%:PP wt%) using extruding and hot press moulding technique. From the results, it can be inferred that Bn30:PP70 mixture composite (BnPP) showed better performance among the composites prepared. For further improvement, betel nut fiber was subjected to detergent wash as well as alkali treatment for composite preparation. This work investigated the tensile strength, bending strength, tensile modulus, bending modulus, elongation at break and impact strength of the composites. Fracture morphology of the composite as well as the water absorption capacity has been monitored.     

Wood Plastic Composite Panels: Influence of the Species,Formulation Variables and Blending Process on the Density and Withdrawal Strength of Fasteners

In this work, the influence of four variable parameters including fiber types (poplar and rice straw), fiber contents (45, 60, and 75 wt%), fiber sizes (20–40 and 40–60 mesh), and blending methods (hot-pressing and extrusion) on the physico-mechanical properties of wood plastic composite panels were studied. Generally, the results showed that each of the above-mentioned parameters had significant effect on the nail and screw withdrawal strength (pull-out load) and density, whereas their interactions did not have highly impressive effects on the properties. All tested properties vary significantly with fiber origin. Composites filled with larger fiber size, produced panels with higher withdrawal strength and density. The effect of blending method on density was maximal. Withdrawal strength values of each sample decreased with increase in fiber loading. The lowest withdrawal strength values of nail and screw were obtained from the samples filled with rice straw. It was found that strength properties of the composites can be improved moderately by adding 45 wt% fiber, 20–40 mesh particle and poplar flour. According to the results, the blending method is a significant variable in the determination of withdrawal strength. Therefore, the blending method can be recommended based on the end product applications.     

Cellulose Fiber/Bentonite Clay/Biodegradable Thermoplastic Composites

Adding cellulose fiber reinforcement can improve mechanical properties of biodegradable plastics, but fiber must be well dispersed to achieve any benefit. The approach to dispersing fiber in this study was to use aqueous gels of sodium bentonite clay. These clay-fiber gels were combined with powdered compostable thermoplastics and calcium carbonate filler. The composite was dried, twin-screw extruded, and injection molded to make thin parts for tensile testing. An experimental design was used to determine the effect of fiber concentration, fiber length, and clay concentration. Polybutylene adipate/terephthalate copolymer (PBAT) and 70/30 polylactic acid (PLA)/PBAT blend were the biodegradable plastics studied. The composite strength decreased compared to the thermoplastics (13 vs. 19 MPa for PBAT, 27 vs. 38 MPa for the PLA/PBAT blend). The composite elongation to break decreased compared to the thermoplastics (170% vs. 831% for PBAT, 4.9% vs. 8.7% for the PLA/PBAT blend). The modulus increased for the composites compared to the thermoplastic standards (149 vs. 61 MPa for PBAT, 1328 vs. 965 MPa for the PLA/PBAT blend). All composite samples had good water resistance.     

Preparation and Characterization of PVC Matrix Composites with Biochemical Sludge

Biochemical sludge (BS), generated in the waste water treatment of paper mills, was pretreated by enzyme hydrolysis. The effect and action mechanism of the enzymatic treatment on the properties of polyvinyl chloride (PVC) matrix composites with BS were discussed. Results showed that when the filler content was 30 wt%, the tensile strength of the PVC composites filled with BS and its modified products which were pretreated by laccase, cellulase and hemicellulase can be increased by 38.64, 67.4, 63.5 and 66.3% than the PVC composite filled with calcium carbonate. When the dosage of filler was 40 wt%, the elastic modulus of PVC composites filled with BS and its above three modified products decreased by 53.3, 52.3, 50.0 and 46.3%, respectively. Meanwhile, the thermal stability of PVC composites can also be improved at the temperature of over 340 °C. It can be concluded that the enzyme pretreatment can improve the application performance of BS usage in PVC matrix composites.     

Renewable Resource-Based Composites of Acorn Powder and Polylactide Bio-Plastic: Preparation and Properties Evaluation

Renewable resource-based composites were prepared with acorn powder and Thermoplastic resin poly(lactic acid) (PLA) by twin-screw extrusion followed by injection molding processing or hot-compression molding processing. The study of the composites microstructure showed poor adhesion between acorn powder and PLA matrix. The hygroscopicity, mechanical properties and melt flow property of composites were promising even though the composites had a 70 wt% content of acorn powder. Silane coupling agent, 4,4′-Methylenebis (phenyl isocyanate) and PLA grafted with maleic anhydride did not show obvious effect on mechanical properties of composites. The impact resistance strength of reinforced composites with steel fiber webs were improved greatly in comparison with those having no steel fiber webs. Thermal properties results of DSC and DMA showed that the presence of acorn powder significantly affected the crystallinity, crystallization temperature (T_c), glass transition temperature (T_g) and melting temperature (T_m) of PLA matrix. The study results proved that composites had superior mechanical properties, enough to partially replace the conventional thermoplastic plastics.     

Enzyme-Retted Flax Fiber and Recycled Polyethylene Composites

Municipal solid wastes generated each year contain potentially useful and recyclable materials for composites. Simultaneously, interest is high for the use of natural fibers, such as flax (Linum usitatissimum L.), in composites thus providing cost and environmental benefits. To investigate the utility of these materials, composites containing flax fibers with recycled high density polyethylene (HDPE) were created and compared with similar products made with wood pulp, glass, and carbon fibers. Flax was either enzyme- or dew-retted to observe composite property differences between diverse levels of enzyme formulations and retting techniques. Coupling agents would strengthen binding between fibers and HDPE but in this study fibers were not modified in anyway to observe mechanical property differences between natural fiber composites. Composites with flax fibers from various retting methods, i.e., dew- vs. enzyme-retting, behaved differently; dew-retted fiber composites resulted in both lower strength and percent elongation. The lowest level of enzyme-retting and the most economical process produces composites that do not appear to differ from the highest level of enzyme-retting. Flax fibers improved the modulus of elasticity over wood pulp and HDPE alone and were less dense than glass or carbon fiber composites. Likely, differences in surface properties of the various flax fibers, while poorly defined and requiring further research, caused various interactions with the resin that influenced composite properties.     

Environmentally Friendly Oil-Modified Polyesters as Polymeric Plasticizers for Poly(vinyl chloride)

Oil-modified polyesters were synthesized to serve as polymeric plasticizers for PVC. A total of four polymeric plasticizers with different average molecular weights were prepared. Characterizations were done using Fourier-transformed infrared spectroscopy, proton nuclear magnetic resonance spectroscopy, and gel permeation chromatography. Some of the tests conducted on PVC films include thermal stability test using thermogravimetric analyser, determination of glass transition temperature (T_g), plasticizer migration and leaching resistance test, morphology study of plasticized PVC films using field emission scanning microscope, toxicity test, and tensile test. Owing to the plasticizing effect of the palm oil-based compound, T_g of the plasticized PVC has decreased to an average of 65 °C at 20 wt% loading. The polymeric plasticizer is also able to contribute positively to the thermal stability and mechanical properties of the PVC films. Some of the advantages of incorporating polymeric plasticizer with high molecular weight includes lower rate of leaching from plastic, and improved tensile strength and elongation at break. Besides, thermal stability of the plastic studied using Kissinger’s and Flynn–Wall–Ozawa’s approaches shows that PVC blended with high molecular weight oil-modified polyester is more thermally stable, evidenced by the increase in the activation energy of decomposition, E_d. Toxicity test using brine shrimp egg shows encouraging results, where the oil-based plasticizer is considerably less toxic compared to some of the commercial plasticizers.     

Fiber from DDGS and Corn Grain as Alternative Fillers in Polymer Composites with High Density Polyethylene from Bio-based and Petroleum Sources

The steady increase in production of corn based ethanol fuel has dramatically increased the supply of its major co-product known as distiller’s dried grain with solubles (DDGS). Large amount of DDGS and corn flour are used as an animal feed. The elusieve process can separate DDGS or corn flour into two fractions: DDGS fraction with enhanced protein and oil content or corn flour fraction with high starch content, and hull fiber. This study investigated the feasibility of using fiber from DDGS and corn grain as alternative fillers to wood fiber in high density polyethylene (HDPE) composites made with two different sources of polymers. Two fiber loading rates of 30 and 50% were evaluated for fiber from DDGS, corn, and oak wood (control) to assess changes in various physical and mechanical properties of the composite materials. Two HDPE polymers, a bio-based HDPE made from sugarcane (Braskem), and a petroleum based HDPE (Marlex) were also compared as substrates. The biobased polymer composites with DDGS and corn fibers showed significantly lower water absorption than the Marlex composite samples. The Braskem composite with 30% DDGS fiber loading showed the highest impact resistance (80 J/m) among all the samples. The flexural properties showed no significant difference between the two HDPE composites.     

Effect of Shrimp Shell Waste on the Properties of Wheat Gluten Based-Bioplastics

Wheat gluten based bioplastics with shrimp shell waste filler were prepared using compression molding. The effects of various amounts (0, 2.5, 5.0, 7.5 and 10 wt%) of shrimp shell powder and calcined shrimp shell powder on the tensile, morphological, thermal properties, and degradation of wheat gluten composites were investigated. The addition of shrimp shell powder improved the tensile properties of the wheat gluten composites. The tensile strength of the wheat gluten composite with 2.5 wt% of shrimp shell powder increased twofold compared to the wheat gluten based-bioplastic without shrimp shell loading. A comparison of the performance of the wheat gluten composites made with different shrimp shell types revealed that composites with calcined shrimp shell powder had better tensile, morphological and thermal properties due to the altered layer structure and higher mineral content resulting from calcination. Moreover, calcined shrimp shell powder had a significant influence on the degradation process of the wheat gluten composite.     

New Non-food-Based Composites of Acorn Nutlet and Polycaprolactone: Preparation and Characterization Evaluation

Two dissimilar renewable resource-based thermoplastic acorn nutlet (TPAN) materials were prepared via twin-screw extrusion with the aid of glycerol or monoethanolamine as plasticizers, and then two TPAN/polycaprolactone (PCL) composites with different plasticized systems were prepared. Mechanical test showed that glycerol-based composites had excellent tensile properties, and at a PCL content of 50 wt%, their tensile strength and elongation at break reached 14.4 MPa and 1,361 %, respectively. The micro-morphologic investigation of liquid-nitrogen brittle fracture surface indicated certain interface adhesion between glycerol-based thermoplastic acorn nutlet (GTPAN) and PCL. Dynamic mechanical thermal analysis , differential scanning calorimetry and thermogravimetric analysis demonstrated that the weight ratios of TPAN in composites significantly affected the crystallinity, glass transition temperature (T_g), melting temperature (T_m) and thermal stability of composites. Soil burial degradation analysis displayed that all composites had excellent biodegradability. These results demonstrated that GTPAN/PCL composites had superior mechanical and biodegradable properties, enough to partially replace the conventional thermoplastic plastics.     

Effect of Cotton Fiber Contents and Lengths on Properties of Thermoplastic Starch Composites Prepared from Rice and Waxy Rice Starches

Biodegradable polymer was prepared as thermoplastic starch (TPS) using rice and waxy rice starches. In order to increase mechanical properties and reduce water absorption of the TPS, cotton fiber was incorporated as the fiber reinforcement into the TPS matrix. The effect of cotton fiber contents and lengths on properties of the TPS was examined. Internal mixer and compression molding machine were used to mix and shape the samples. It was found that the thermoplastic rice starch (TPRS) showed higher stress at maximum load and Young’s modulus but lower strain at maximum load than the thermoplastic waxy rice starch (TPWRS). In addition, stress at maximum load and Young’s modulus of both TPRS and TPWRS increased significantly with the addition of the cotton fiber. Cotton fiber contents and lengths also affected mechanical properties of the TPRS and TPWRS composites. Moreover, water absorption of the TPRS and TPWRS composites decreased by the use of the cotton fibers. FT-IR and XRD techniques were used to study a change in functional group and crystallinity of the thermoplastic starch composites. Morphological, thermal and biodegradable properties of different thermoplastic starch composites were also investigated.     

Dispersion and Reinforcing Potential of Carboxymethylated Nanofibrillated Cellulose Powders Modified with 1-Hexanol in Extruded Poly(Lactic Acid) (PLA) Composites

Bionanocomposites of poly(lactic acid) (PLA) and chemically modified, nanofibrillated cellulose (NFC) powders were prepared by extrusion, followed by injection molding. The chemically modified NFC powders were prepared by carboxymethylation and mechanical disintegration of refined, bleached beech pulp (c-NFC), and subsequent esterification with 1-hexanol (c-NFC-hex). A solvent mix was then prepared by precipitating a suspension of c-NFC-hex and acetone-dissolved PLA in ice-cold isopropanol (c-NFC-hex_sm), extruded with PLA into pellets at different polymer/fiber ratios, and finally injection molded. Dynamic mechanical analysis and tensile tests were performed to study the reinforcing potential of dried and chemically modified NFC powders for PLA composite applications. The results showed a faint increase in modulus of elasticity of 10?% for composites with a loading of 7.5?% w/w of fibrils, irrespective of the type of chemically modified NFC powder. The increase in stiffness was accompanied by a slight decrease in tensile strength for all samples, as compared with neat PLA. The viscoelastic properties of the composites were essentially identical to neat PLA. The absence of a clear reinforcement of the polymer matrix was attributed to poor interactions with PLA and insufficient dispersion of the chemically modified NFC powders in the composite, as observed from scanning electron microscope images. Further explanation was found in the decrease of the thermal stability and crystallinity of the cellulose upon carboxymethylation.