Laboratory evaluation of thermophilic-anaerobic digestion to produce Class A biosolids. 2. Inactivation of pathogens and indicator organisms in a continuous-flow reactor followed by batch treatment.

Thermophilic-anaerobic digestion in a single-stage, mixed, continuous-flow reactor is not approved in the United States as a process capable of producing Class A biosolids for land application. This study was designed to evaluate the inactivation of pathogens and indicator organisms in such a reactor followed by batch treatment in a smaller reactor. The combined process was evaluated at 53 degrees C with sludges from three different sources and at 51 and 55 degrees C with sludge from one of the sources. Feed sludge to the continuous-flow reactor was spiked with the pathogen surrogates Ascaris suum and vaccine-strain poliovirus. Feed and effluent were analyzed for these organisms and for indigenous Salmonella spp., fecal coliforms, Clostridium perfringens spores, and somatic and male-specific coliphages. No viable Ascaris eggs were observed in the effluent from the continuous reactor at 53 or 55 degrees C, with greater than 2-log removals across the digester in all cases. Approximately 2-log removal was observed at 51 degrees C, but all samples of effluent biosolids contained at least one viable Ascaris egg at 51 degrees C. No viable poliovirus was found in the digester effluent at any of the operating conditions, and viable Salmonella spp. were measured in the digester effluent in only one sample throughout the study. The ability of the continuous reactor to remove fecal coliforms to below the Class A monitoring limit depended on the concentration in the feed sludge. There was no significant removal of Clostridium perfringens across the continuous reactor under any condition, and there also was limited removal of somatic coliphages. The removal of male-specific coliphages across the continuous reactor appeared to be related to temperature. Overall, at least one of the Class A pathogen criteria or the fecal coliform limit was exceeded in at least one sample in the continuous-reactor effluent at each temperature. Over the range of temperatures evaluated, the maximum time required to meet the Class A criteria by batch treatment of the continuous-reactor effluent was 1 hour for Ascaris suum and Salmonella spp. and 2 hours for fecal coliforms.     

Influence of staging, mean cell residence time, and thermophilic temperature on the thermophilic anaerobic digestion process.

As Class B biosolids land application has become less acceptable to many local jurisdictions, low-cost processes to achieve Class A standards have become more popular. Prominent among these low-cost processes is thermophilic anaerobic digestion. As a result, thermophilic anaerobic digestion is now a popular topic in wastewater treatment literature, but quantifiable methods for selecting a particular thermophilic process have not been offered. To provide for this need, an empirical model was developed from data collected in thermophilic anaerobic digestion studies conducted using East Bay Municipal Utility District's (Oakland, California) primary and waste activated sludge to feed both bench- and full-scale digesters. The model predicts at which thermophilic temperature and mean cell residence time (MCRT) one process will outperform or equal another, with respect to fecal coliform reduction. The different disinfection efficiencies in the different thermophilic processes might be explained by the presence or absence of high volatile acid and/or un-ionized ammonia levels in the processes' digested sludges. Data from these studies also show an apparent relationship between increased thermophilic temperatures and volatile solids destruction, and between increased temperatures and specific volatile acids production, for digesters operating at a 13-day MCRT and higher, but not for digesters operating at a 2-day MCRT.     

Recurrence of fecal coliforms and Salmonella species in biosolids following thermophilic anaerobic digestion.

The U.S. Environmental Protection Agency (U.S. EPA) Part 503 Biosolids Rule requires the fecal coliform (indicator) or Salmonella species (pathogen) density requirements for Class A biosolids to be met at the last point of plant control (truck-loading facility and/or farm for land application). The three Southern Californian wastewater treatment plants in this study produced biosolids by thermophilic anaerobic digestion and all met the Class A limits for both fecal coliforms and Salmonella sp. in the digester outflow biosolids. At two plants, however, a recurrence of fecal coliforms was observed in postdigestion biosolids, which caused exceedance of the Class A limit for fecal coliforms at the truck-loading facility and farm for land application. Comparison of observations at the three plants and further laboratory tests indicated that the recurrence of fecal coliforms can possibly be related to the following combination of factors: (1) incomplete destruction of fecal coliforms during thermophilic anaerobic digestion, (2) contamination of Class A biosolids with fecal coliforms from external sources during postdigestion, (3) a large drop of the postdigestion biosolids temperature to below the maximum for fecal coliform growth, (4) an unknown effect of biosolids dewatering in centrifuges. At Hyperion Treatment Plant (City of Los Angeles, California), fecal coliform recurrence could be prevented by the following: (1) complete conversion to thermophilic operation to exclude contamination by mesophilically digested biosolids and (2) insulation and electrical heat-tracing of postdigestion train for maintaining a high biosolids temperature in postdigestion.     

Steam-explosion pretreatment for enhancing anaerobic digestion of municipal wastewater sludge.

This study evaluated the use of steam explosion as a pretreatment for municipal wastewater treatment sludges and biosolids as a technique for enhancing biogas generation during anaerobic digestion. Samples of dewatered anaerobic digester effluent (biosolids) and a mixture of thickened waste activated sludge (TWAS) and biosolids were steam-exploded under differing levels of intensity in this study. The results indicate that steam explosion can solublize components of these sludge streams. Increasing the intensity of the steam-explosion pressure and temperature resulted in increased solublization. The steam-explosion pretreatment also increased the bioavailability of sludge components under anaerobic digestion conditions. Increasing the steam-explosion intensity increased the ultimate yield of methane during anaerobic digestion. Batch anaerobic digestion tests suggested that pretreatment at 300 psi was the most optimal condition for enhanced biogas generation while minimizing energy input. Semicontinuous anaerobic digestion revealed that the results that were observed in the batch tests were sustainable in prolonged operation. Semicontinuous digestion of the TWAS/biosolids mixture that was pretreated at 300 psi generated approximately 50% more biogas than the controls. Semicontinuous digestion of the pretreated biosolids resulted in a 3-fold increase in biogas compared with the controls. Based on capillary suction test results, steam-explosion pretreatment at 300 psi improved the dewaterability of the final digested sludge by 32 and 45% for the TWAS/ biosolids mixture and biosolids, respectively, compared with controls. The energy requirements of the nonoptimized steam-explosion process were substantially higher than the additional energy produced from enhanced digestion of the pretreated sludge. Substantial improvements in energy efficiency will be required to make the process viable from an energy perspective.     

Overview of anaerobic treatment: thermophilic and propionate implications.

Difficulties in achieving low propionate concentrations in anaerobically treated effluents are frequently reported in the literature (Ahring, 1994; Kugelman and Guida, 1989; Rimkus et al., 1982), especially at thermophilic temperatures, with concentrations as high as 1000 to 9600 mg/L sometimes produced. This paper will detail the effect of several variables on the performance of both mesophilic and thermophilic regimes. Studies concerning the effect of the following four important factors on performance are included: reactor configuration, inorganic nutrient supplementation, substrate characteristics, and the unique role of microbial consortia proximity in enhancing performance. Reactor configuration modifications, essential nutrient additions, and the importance of close microbial proximity were all found to contribute to improvement in thermophilic anaerobic digestion in all the studies. It was found that, in substrates that shunt significant amounts of the electron donor through propionate, performance was critically related to reactor optimization, with propionate removal efficiency considerably improved using intact upflow anaerobic sludge blanket granules, less so in a homogenized granule slurry blanket, and noticeably reduced even more when the completely stirred reactor configuration of homogenized granules was used. The critical importance of extremely close microbial consortia proximity in maintaining hydrogen intermediates at very low levels to efficiently convert propionate to hydrogen and acetate was demonstrated. Compared to mesophilic digestion, thermophilic digestion manifested elevated levels of propionate, except in the nonmixed reactors, which had close microbial consortia proximity. The reactor configuration with the best results was the anaerobic digestion elutriated phased treatment (ADEPT) scheme, in which the raw sludge was elutriated of its fermenting volatile fatty acids, as they are generated in a short 5- to 8-day solids retention time (SRT) in one reactor and the elutriate then metabolized by passing up through a methanogenic granule or slurry blanket (with its close microbial consortia proximity) in a separate reactor with a 20- to 50-day SRT. Loading rates and performance of the ADEPT reactor configuration were superior to the standard continuously stirred tank reactor, and ADEPT thermophilic temperatures allowed higher organic loading rates without high propionate concentrations in the effluent.     

Oxidative co-treatment using hydrogen peroxide with anaerobic digestion of excess municipal sludge.

The effect of an oxidative co-treatment on anaerobic digestion of a mixture of primary and waste activated sludge was investigated. The oxidant used in this study was hydrogen peroxide (H2O2). A maximum improvement in solid destruction of 15.2% was achieved in the overall process, with a dosage of 2.0 g H2O2/g influent volatile suspended solids (VSS(influent)). All configurations operated at this dosage also showed statistically significant increases in solids removal. A statistically significant enhancement in overall solids destruction was observed for the lower oxidant dosage (0.5 H2O2/g VSS(influent)). Surprisingly, for 1.0 g H2O2/g VSS(influent), only one of the three configurations involving oxidative co-treatment showed significant increases in solids destruction. Special attention was paid to the performance of this process relative to fecal coliforms destruction. Class A biosolids were obtained for all the different hydrogen peroxide dosages used when oxidative co-treatment is combined with a two-stage anaerobic digestion process.     

Laboratory-scale comparison of anaerobic-digestion alternatives.

Laboratory-scale digesters were used to perform side-by-side evaluations of alternative digestion systems including thermophilic-mesophilic-phased digestion (TPAD), acid/methane-phased digestion, mesophilic digestion, and the performance of the thermophilic stage of TPAD alone. Total detention times in the systems evaluated varied from 8 to 20 days. Temperatures in the mesophilic stage of TPAD were varied from 35 to 43.3 degrees C and temperatures in the thermophilic stage were varied from 55 to 58.9 degrees C. The purpose of the study was to evaluate volatile solids (VS) reduction and thickening properties of the different systems. Parameters evaluated included solids, volatile acids, gas production and quality, various chemical constituents of the sludge, and thickening properties using polymer and ferric chloride plus polymer. The TPAD systems were found capable of higher VS destruction at total detention times of 10 and 12.5 days compared to single-stage mesophilic or thermophilic digestion at 15 to 20 days. A laboratory-scale thickening test was performed to evaluate thickening properties. Based on obtaining 95% capture in the test, the polymer demand of mesophilic and acid-methane-phased digestion was the lowest. The TPAD system required approximately 180% of the dosage of the mesophilic sludge and thermophilic sludge required approximately 310% of the dosage. Temperatures of 40.5 and 43.3 degrees C in the mesophilic stage of TPAD were found to increase the polymer requirement and decrease the VS reduction of the TPAD system. Higher temperatures (above 56.1 degrees C) and lower detention times (less than 15 days) in the thermophilic digesters seemed to result in problems with degradation of volatile acids, particularly propionic acid.     

污泥同时浓缩消化新型反应器的开发研究

针对污泥厌氧处理的问题,对污泥浓缩消化一体化反应器进行了开发研究,提出了ICSTD、MISTD和TISTD 3套反应器,反应器由内外2个反应室组成,采用沼气搅拌或机械搅拌。3套反应器的试验结果表明：在中温条件下,进泥含水率98.3%～99.8%,VS/TS 0.52～0.69时,排泥含水率87.4%～97.3%,VS/TS 0.23～0.51,产气量8.2～76.6 L/d,其浓缩和消化效果优于其他反应器。     

好氧/缺氧消化降解污泥特征分析

为考察好氧/缺氧消化过程中污泥降解的特征,利用2个反应器进行对比试验,研究好氧/缺氧和好氧消化2个过程中VS的去除,pH和碱度变化,消化上清液中COD和氮元素变化等情况。试验结果表明:好氧/缺氧消化能够满足污泥稳定的要求,在常温条件下,消化16 d VS去除率即可达到38.2%,同时比好氧消化节约曝气能耗。好氧/缺氧消化对污泥中总氮的去除率高于传统的好氧消化,达到了36.4%,而且能够降低消化污泥上清液中的氨氮和硝态氮浓度。     

Pretreatment of sludge with microwaves for pathogen destruction and improved anaerobic digestion performance.

A new way of generating Class A sludge using microwaves was evaluated through a series of laboratory-scale experiments. Microwaves provide rapid and uniform heating throughout the material. Other benefits of microwave treatment include instant and accurate control and selective and concentrated heating on materials, such as sludge, that have a high dielectric loss factor. Sludge was irradiated with 2450-MHz microwaves, and fecal coliforms were counted. Fecal coliforms were not detected at 65 degrees C for primary sludge and anaerobic digester sludge and at 85 degrees C for waste activated sludge when sludge was irradiated with 2450-MHz microwaves. During the bench-scale anaerobic digester operation, the highest average log reduction of fecal coliforms was achieved by the anaerobic digester fed with microwave-pretreated sludge (> or = 2.66 log removal). The anaerobic digester fed with microwave-irradiated sludge was more efficient in inactivation of fecal coliforms than the other two digesters fed with raw sludge and externally heated sludge, respectively. It took more than three hydraulic retention times for a bench-scale mesophilic anaerobic digester to meet Class A sludge requirements after feeding microwave-irradiated sludge. Class A sludge can be produced consistently with a continuously fed mesophilic anaerobic digester if sludge is pretreated with microwaves to reach 65 degrees C.     

A comparison of membrane bioreactor and conventional-activated-sludge mixed liquor and biosolids characteristics.

Characteristics and behavior of raw and digested mixed liquor derived from a membrane bioreactor (MBR) and a full-scale activated-sludge (FSAS) facility were compared. The accumulation of nondegradable chemical oxygen demand in the MBR appears to play an important role in increasing the observed biological yield coefficient (Y(obs)), reducing average floc size, decreasing total suspended solids/total solids and volatile suspended solids/volatile solids (VS) ratios, and reducing specific-oxygen-uptake rates of the mixed liquor relative to FSAS-derived biological solids. Membrane bioreactor sludges exhibited lower VS destruction following 30 days mesophilic-anaerobic and aerobic digestion when compared to FSAS sludges. Significant deterioration in dewatering behavior was observed for the FSAS biosolids after anaerobic digestion and, to a lesser extent, following aerobic digestion. In comparison, digestion had a small affect on dewatering efficiency and conditioner requirements for MBR biosolids. Full-scale facilities using membrane separation may need to tailor digestion and dewatering processes to the specific characteristics of MBR sludges.     

ICSTD反应器处理污泥的启动试验研究

新型内循环污泥浓缩消化反应器（ICSTD）处理污泥的启动运行试验采用某污水处理厂二沉池好氧活性污泥进行驯化培养,使反应器正常启动运行。在日处理量为50 L/d,进泥含水率为99.23％～99.46％,进泥VS/TS为0.65～0.73,进泥COD为4 115～5 780 mg/L,反应器容积负荷为1.31 kg COD/(m³·d)时,排泥含水率在96.2％～97.3％,排泥VS/TS为0.48～0.57,COD去除率在95％以上,出水pH在6.6～7.1,且上清液澄清。试验结果表明： ICSTD反应器处理污泥的启动试验,采用直接培养污泥启动的方式培养厌氧污泥历时66 d,能较快地培养厌氧污泥且运行稳定,对污泥的浓缩消化起到较好的作用,同时对反应器后续运行的消化效果提供了一个良好的条件。     

Aerobic sludge digestion under low dissolved oxygen concentrations.

Low dissolved oxygen (DO) concentrations occur commonly in aerobic digesters treating thickened sludge, with benefits of smaller digester size, much reduced aeration cost, and higher digestion temperature (especially important for plants in colder areas). The effects of low DO concentrations on digestion kinetics were studied using the sludge from municipal wastewater treatment plants in Akron, Ohio, and Los Lunas, New Mexico. The experiments were conducted in both batch digestion and a mixed mode of continuous, fed-batch, and batch operations. The low DO condition was clearly advantageous in eliminating the need for pH control because of the simultaneous occurrence of nitrification and denitrification. However, when compared with fully aerobic (high DO) systems under constant pH control (rare in full-scale plants), low DO concentrations and a higher solids loading had a negative effect on the specific volatile solids (VS) digestion kinetics. Nonetheless, the overall (volumetric) digestion performance depends not only on the specific digestion kinetics, but also the solids concentration, pH, and digester temperature. All of the latter factors favor the low DO digestion of thickened sludge. The significant effect of temperature on low DO digestion was confirmed in the mixed-mode study with the Akron sludge. When compared with the well-known empirical correlation between VS reduction and the product (temperature x solids retention time), the experimental data followed the same trend, but were lower than the correlation predictions. The latter was attributed to the lower digestible VS in the Akron sludge, the slower digestion at low DO concentrations, or both. Through model simulation, the first-order decay constant (kd) was estimated as 0.004 h(-1) in the mixed-mode operations, much lower than those (0.011 to 0.029 h(-1)) obtained in batch digestion. The findings suggested that the interactions among sludges with different treatment ages may have a substantially negative effect on digestion kinetics. The use of multistage digesters, especially with small front-end reactors, may be advantageous in both "process" kinetics and "biological reaction" kinetics for sludge digestion.     

Comparative mesophilic and thermophilic anaerobic digestion of palm oil mill effluent using upflow anaerobic sludge blanket

The effects of organic loading rate and operating temperature on the microbial diversity and performances of upflow anaerobic sludge blanket (UASB) reactors treating palm oil mill effluent (POME) were investigated. The following two UASB reactors were run in parallel for comparison: (1) under a mesophilic condition (37 degrees C) and (2) under a mesophilic condition in transition to a thermophilic condition (57 degrees C). A polymerase chain reaction (PCR)-based denaturing gradient gel electrophoresis (DGGE) analysis showed that the microbial population profiles significantly changed with the organic loading rate (OLR) and the temperature transition from the mesophilic to the thermophilic condition. Significant biomass washout was observed for the mesophilic UASB when operating at a high organic loading rate (OLR) of 9.5 g chemical oxygen demand (COD)/L.d. In contrast, the thermophilic UASB can be operated at this OLR and at a temperature of 57 degrees C with satisfactory COD removal and biogas production. The PCR-based DGGE analysis suggested that the thermophilic temperature of 57 degrees C was suitable for a number of hydrolytic, acidogenic, and acetogenic bacteria.     

Applications of two-phase anaerobic degradation in industrial wastewater treatment

Prospects for the phased anaerobic treatment of wastewater are extremely promising. With the variety of reactor designs available and the amenability of reactors to modification, existing treatment systems may be replaced or upgraded as required to achieve increased stability, higher loading capacities and greater process efficiencies than single-stage systems. In recent times, various reactor configurations and substrates are applied to two-phase anaerobic process. This paper reviews applications and studies of two-phase anaerobic degradation for wastewater treatment, sums up the performance of application to treating waste from distillery, landfill leachate, coffee, cheese whey and dairy, food, pulp and paper, sludge and solid, etc., and summarises reactor configurations, environmental and operational conditions, and comparisons of two-phase anaerobic digestion with other anaerobic reactors.     

Kinetics of thermophilic anaerobes in fixed-bed reactors

The main objective of this study is to estimate growth kinetic constants and the concentration of "active" attached biomass in two anaerobic thermophilic reactors which contain different initial sizes of immobilized anaerobic mixed cultures and decompose distillery wastewater. This paper studies the substrate decomposition in two lab-scale fixed-bed reactors operating at batch conditions with corrugated tubes as support media. It can be demonstrated that high micro-organisms-substrate ratios favor the degradation activity of the different anaerobic cultures, allowing the stable operation without lag-phases and giving better quality in effluent. The kinetic parameters obtained--maximum specific growth rates (mu(max)), non-biodegradable substrate (S(NB)) and "active or viable biomass" concentrations (X(V0))--were obtained by applying the Romero kinetic model [L.I. Romero, 1991. Desarrollo de un modelo matemático general para los procesos fermentativos, Cinética de la degradación anaerobia, Ph.D. Thesis, University of Cádiz (Spain), Serv. Pub. Univ. Cádiz], with COD as substrate and methane (CH4) as the main product of the anaerobic process. This method is suitable to calculate and to differentiate the main kinetic parameters of both the total anaerobic mixed culture and the methanogenic population. Comparison of experimental measured concentration of volatile attached solids (VS(att)) in both reactors with the estimated "active" biomass concentrations obtained by applying Romero kinetic model [L.I. Romero, 1991. Desarrollo de un modelo matemático general para los procesos fermentativos, Cinética de la degradación anaerobia, Ph.D. Thesis, University of Cádiz (Spain), Serv. Pub. Univ. Cádiz] shows that a large amount of inert matter is present in the fixed-bed reactor.     

Characteristics of granular sludge developed in an upflow anaerobic sludge fixed-film bioreactor treating palm oil mill effluent.

In the present study, characteristics of the granular sludge (including physical characteristics under stable conditions and process shocks arising from suspended solid overload, soluble organic overload, and high temperature; biological activity; and sludge kinetic evaluation in a batch experiment) developed in an upflow anaerobic sludge blanket fixed-film reactor for palm oil mill effluent (POME) treatment was investigated. The main aim of this work was to provide suitable understanding of POME anaerobic digestion using such a granular sludge reactor, particularly with respect to granule structure at various operating conditions. The morphological changes in granular sludge resulting from various operational conditions was studied using scanning electron microscopy and transmission electron microscopy images. It was shown that the developed granules consisted of densely packed rod- (Methanosaeta-like microorganism; predominant) and cocci- (Methanosarsina) shaped microorganisms. Methanosaeta aggregates functioned as nucleation centers that initiated granule development of POME-degrading granules. Under the suspended solid overload condition, most of the granules were covered with a thin layer of fiberlike suspended solids, so that the granule color changed to brown and the sludge volume index also increased to 24.5 from 12 to 15 mL/g, which caused a large amount of sludge washout. Some of the granules were disintegrated because of an acidified environment, which originated from acidogenesis of high influent organic load (29 g chemical oxygen demand [COD]/L d). At 60 degrees C, the rate of biomass washout increased, as a result of disintegration of the outer layer of the granules. In the biological activity test, approximately 95% COD removal was achieved within 72 hours, with an initial COD removal rate of 3.5 g COD/L d. During POME digestion, 275 mg calcium carbonate/L bicarbonate alkalinity was produced per 1000 mg COD(removed)/ L. A consecutive reaction kinetic model was used to simulate the data obtained from the sludge activity in the batch experiment. The mathematical model gave a good fit with the experimental results (R2 > 0.93). The slowest step was modeled to be the acidification step, with a rate constant between 0.015 and 0.083 hours(-1), while the rate constant for the methanogenic step was obtained to be between 0.218 and 0.361 hours(-1).     

Production of polyhydroxyalkanoate during treatment of low-phosphorus-content wastewater.

To evaluate whether poly-beta-hydroxyalkanoate (PHA) production and wastewater treatment could be combined in a single biological process, a bench-scale sequencing batch reactor was operated with sequential anaerobic and aerobic stages and removal of excess sludge at different stages of treatment. The reactor treated synthetic wastewater with a high organic and low nutrient content, simulating industrial wastewater. Chemical oxygen demand removal efficiency was more than 90% in all cases. Poly-beta-hydroxyalkanoate accumulation was significant, although it did not appear to be induced by oxygen limitations during the anaerobic stage. Sphaerotilus natans was apparently the dominant PHA-accumulating organism at the end of each reactor run and corresponded to a PHA accumulation of 16 to 20% of the total dry cell mass. Before S. natans dominated the reactors, PHA accumulation was approximately 17% when biomass was removed at the end of the aerobic stage and 6.6% when sludge removal also occurred during the anaerobic stage.     

Bioenergy production from diluted poultry manure and microbial consortium inside Anaerobic Sludge Bed Reactor at sub-mesophilic conditions

In this study, anaerobic treatability of diluted chicken manure (with an influent feed ratio of 1 kg of fresh chicken manure to 6 L of tap water) was investigated in a lab-scale anaerobic sludge bed (ASB) reactor inoculated with granular seed sludge. The ASB reactor was operated at ambient temperature (17–25°C) in order to avoid the need of external heating up to higher operating temperatures (e.g., up to 35°C for mesophilic digestion). Since heat requirement for raising the temperature of incoming feed for digestion is eliminated, energy recovery from anaerobic treatment of chicken manure could be realized with less operating costs. Average biogas production rates were calculated ca. 210 and 242 L per kg of organic matter removed from the ASB reactor at average hydraulic retention times (HRTs) of 13 and 8.6 days, respectively. Moreover, average chemical oxygen demand (COD) removal of ca. 89% was observed with suspended solids removal more than 97% from the effluent of the ASB reactor. Influent ammonia, on the other hand, did not indicate any free ammonia inhibition due to dilution of the raw manure while pH and alkalinity results showed stability during the study. Microbial quantification results indicated that as the number of bacterial community decreased, the amount of Archaea increased through the effective digestion volume of the ASB reactor. Moreover, the number of methanogens displayed an uptrend like archaeal community and a strong correlation (?0.645) was found between methanogenic community and volatile fatty acid (VFA) concentration especially acetate.     

IC厌氧反应器处理有机废水启动实验研究

设计了一套IC反应器装置,接种啤酒厂生产废水消化污泥,采用人工配水对其进行启动运行,考察了IC反应器的启动运行状况、效果及影响因素,并在反应器运行结束后观察了污泥状态的变化.结果表明,容积负荷提高至4.7 kg/(m3·d),出水COD浓度稳定在250 mg/L左右,去除率维持在85%以上,反应器内出现污泥分层现象,颗...