SRV菌去除电镀废水中铜的研究

为探索新的铜废水处理方法,更有效地治理铜废水造成的环境污染,用微生物及电镜法对SRV菌去除电镀废水中铜进行了研究。研究了菌量、铜离子浓度、溶液的pH值、作用的温度和时间等因素对SRV菌去除溶液中铜离子的影响。在菌废比1:1的情况下,对铜浓度为246.8mg/L的废水去除率达99.12％。观察了SRV菌处理铜废水前、后的扫描电镜、超薄切片透射电镜,推测其去除机制为铜与SRV菌代谢产物反应生成沉淀或直接被吸附于菌体表面而去除。     

Electrochemical oxidation of polyethylene glycol in electroplating solution using paraffin composite copper hexacyanoferrate modified (PCCHM) anode

Electrochemical oxidation of polyethylene glycol (PEG) in an acidic(pH 0.18 to 0.42) and high ionic strength electroplating solution was investigated. The electroplating solution is a major source of wastewater in the printing wiring board industry. A paraffin composite copper hexacyanoferrate modified(PCCHM) electrode was used as the anode and a bare graphite electrode was used as the cathode. The changes in PEG and total organic carbon (TOC) concentrations during the course of the reaction were monitored. The efficiency of the PCCHM anode was compared with bare graphite anode and it was found that the former showed significant electrocatalytic property for PEG and TOC removal. Chlorides present in the solution were found to contribute significantly in the overall organic removal process. Short chain organic compounds like acetic acid, oxalic acid, formic acid and ethylene glycol formed during electrolysis were identified by HPLC method. Anode surface area and applied current density were found to influence the electro-oxidation process, in which the former was found to be dominating. Investigations of the kinetics for the present electrochemical reaction suggested that the two stage first-order kinetic model provides a much better representation of the overall mechanism of the process if compared to the generalized kinetic model.     

铁屑内电解法处理EDTA溶液中络合铜离子

采用批式试验和现代仪器分析研究了铁屑内电解法处理EDTA溶液中络合铜离子,考察了溶液浓度、溶液pH、温度和铁屑粒径等因素对铜离子去除过程的影响.结果表明,铜离子去除过程符合表观一级动力学方程.在pH 2.0～11.0范围内,pH值越低越利于铜离子去除;在酸性条件下溶液pH随内电解进行升高,在碱性条件下溶液pH随内电解进...     

废旧印刷线路板电解过程中铜的分布特性

以废旧印刷线路板粉末为原材料,采用压片电解方法回收单质铜,研究了CuSO_4·5H2O浓度、H_2SO_4浓度、电流密度、电解时间和NaCl浓度对电解过程中Cu分布特性的影响。结果表明:废旧印刷线路板中的Cu以Cu2+的形式进入溶液,最终以粉末形式沉积在阴极;过高的H_2SO_4浓度、电流密度和NaCl浓度会导致析氢反应等,从而降低Cu在阴极和溶液中的分布;当CuSO_4·5H_2O浓度、H_2SO_4浓度、电流密度、电解时间、NaCl浓度分别为50 g/L、6 mol/L、80 m A/cm~2、5 h、40 g/L时,Cu在阴极、溶液、阳极泥中的分布比率分别为63.16%、34.14%和2.70%。     

新型二氧化铅电极处理硝基苯废水

采用高压塑片的方法制备了一种PbO₂电极,用X衍射、扫描电镜、火焰原子吸收分光光度法对该电极性能进行了考察,并探讨了该电极降解硝基苯的机理和工艺条件.结果表明,该电极与普通石墨电极相比,COD_Cr去除率更高,电解5 h COD_Cr去除率最高可达65%.由于PbO₂电极具有较高的析氧电位,在阳极极化下,PbO₂电极表面易生成·OH,这是其电解效率高的主要原因.该电极电解硝基苯的最适条件:ρ(硝基苯)为501.5 mg/L,电极间距为3 cm,溶液pH为7.利用该电极处理含磷酸盐和氯离子的硝基苯废水效果尤为突出,但由于阴极的还原作用,电解过程中硝基苯不能被完全氧化.      

Electrochemical degradation of p-nitrophenol with different processes

The electrochemical degradation of p-nitrophenol (PNP) under di erent conditions was investigated. The electrochemical behavior of PNP and its reduction product p-aminophenol (PAP) on stainless steel cathode and Ti/Pt anode through cyclic voltammetry were observed. Electrochemical degradation process was performed in an undivided cell and 92% PNP was removed corresponding to a 22% total organic carbon removal. A divided cell was also used and it was found that PNP degradation was mainly attributed to cathodic reduction, while anodic oxidation was responsible for PNP removal due to the reaction with hydroxyl radicals and surface oxide generated on the anode. The sequential electrolytic processes, reduction-oxidation and oxidation-reduction, were compared in the divided cell. In the case of reduction-oxidation process, the total organic carbon removal reached 40%, but PNP removal was the same with the undivided cell. A black deposit was found in the e uent and identified by Fourier transform infrared spectroscopy as a polymer of PAP produced by the 1,4-addition reaction of quinoneimine. Intermediates left in the solution such as hydroquinone, p-benzoquinone and PAP were determined by high performance liquid chromatography. Whereas, the oxidation-reduction process proved unsatisfying.     

阴极电解液对Cd污染红壤电动修复的影响

针对土壤重金属电动修复过程中阴极电解室pH升高会对重金属的去除产生不利影响的问题,利用Fe3+/Fe2+、Cu2+/Cu标准电极电位较高的优势,以人工模拟Cd污染红壤为研究对象,对不同阴极电解液[Fe（NO₃）₃、CuSO₄、柠檬酸]的电动修复效果进行系统分析.结果表明:分别将Fe（NO₃）₃、CuSO₄、柠檬酸加入阴极电解室中,pH均控制在2~3,电动修复10 d后发现,将Fe（NO₃）₃溶液、CuSO₄溶液和柠檬酸作为阴极电解液均可以有效控制阴极室的pH,CuSO₄溶液、柠檬酸的加入对土壤中Cd的去除效果较差,而且Cu2+的加入增加了土壤重金属二次污染的风险.相对于CuSO₄、柠檬酸试验组,Fe（NO₃）₃试验组土壤中Cd的去除率较高（大于87.27%）,Fe（NO₃）₃试验组对土壤中Cd的修复效果也最为明显,土壤中w（Cd）由阴极附近的75.95 mg/kg降至阳极附近的9.13 mg/kg.分析电动修复后各试验组中不同形态Cd在Cd总量中所占比例的分析,结果显示,w（弱酸提取态Cd）所占比例由初始的74.57%最高可达到92.69%[Fe（NO₃）₃试验组],表明Fe（NO₃）₃的加入有助于促进土壤中Cd的迁移.研究显示,相比于CuSO₄溶液、柠檬酸,Fe（NO₃）₃溶液作为阴极电解液在控制阴极电解室pH升高的前提下,显著促进了土壤中Cd的解吸和迁移,并达到最佳修复效果.      

催化铁内电解法处理难降解有机废水

催化铁内电解法是一种新型的有效处理废水的方法。在传统的铁碳内电解中加入无机催化剂铜，扩大原电池的两极电位差，使更多的有机物得到还原。结果表明，催化铁内电解法可改善难降解有机废水的可生化性，使活性艳红染料废水的B/C比从0升高到0.15。运行成本低廉、预处理能耗低，催化剂铜经连续运行数月后未发生纯化现象，只需一次性投资。     

Study on the mechanism of copper–ammonia complex decomposition in struvite formation process and enhanced ammonia and copper removal

Heavy metals and ammonia are difficult to remove from wastewater, as they easily combine into refractory complexes. The struvite formation method (SFM) was applied for the complex decomposition and simultaneous removal of heavy metal and ammonia. The results indicated that ammonia deprivation by SFM was the key factor leading to the decomposition of the copper–ammonia complex ion. Ammonia was separated from solution as crystalline struvite, and the copper mainly co-precipitated as copper hydroxide together with struvite. Hydrogen bonding and electrostatic attraction were considered to be the main surface interactions between struvite and copper hydroxide. Hydrogen bonding was concluded to be the key factor leading to the co-precipitation. In addition, incorporation of copper ions into the struvite crystal also occurred during the treatment process.     

给水厂污泥颗粒制备及对铜离子的吸附行为

将给水厂污泥和粘土以质量比1：2制备了一种新型污泥颗粒,考察其对溶液中铜离子的吸附行为.结果发现,污泥颗粒对水中铜离子具有良好的吸附效果,对铜的吸附量随时间增加而增大,180min时可达最大吸附量的85%左右,吸附过程符合准二级吸附动力学方程;Langmuir等温吸附方程式可较好拟合不同温度时的吸附数据,且温度越高,平衡吸附量越大.多种重金属离子共存时,污泥颗粒仍优先吸附铜离子.pH值可显著影响污泥颗粒对铜离子的吸附,pH<5时,污泥颗粒对铜离子的吸附去除率随pH值升高而增大,pH=5时吸附去除效果最好.采用扫描电镜、红外光谱等对吸附铜离子前后的污泥颗粒进行表征,发现污泥颗粒表面粗糙、孔隙发达,含丰富表面基团,能够通过静电吸引、羟基取代和表面络合吸附铜离子.     

Electrokinetic removal of chromium and copper from contaminated soils by lactic acid enhancement in the catholyte

The electrokinetic removal of chromium and copper from contaminated soils by adding lactic acid in cathode chamber as an enhancing reagent was evaluated. Two sets of duplicate experiments with chromium contaminated kaolinite and with a silty soil sampled from a supeffund site in Califomia of USA and polluted by Cr and Cu, were carried out in a constant current mode. Changes of soil water content and soil pH before and after the electrokinetic experiments, and variations of voltage drop and electroosmosis flow during the treatments were examined. The results indicated that Cr, spiked as Cr(Ⅵ) in the kaolinite, was accumulated mainly in the anode chamber, and some of Cr and metal hydroxides precipitated in the soil sections in contact with the cathode, which significantly increased electrical energy consumption. Treatment of the soil collected from the site showed accumulation of large amounts of Cr and Cu in the anode chamber while none was detected in the cathode one. The results suggested that the two metals either complexed with the injected lactic acid at the cathode or existed as negatively charged complex, and electromigrated toward the anode under a voltage gradient.     

Adsorption characteristics of copper in rivers contaminated by acid mine drainage from copper mine

Ａｄｓｏｒｐｔｉｏｎｃｈａｒａｃｔｅｒｉｓｔｉｃｓｏｆｃｏｐｐｅｒｉｎｒｉｖｅｒｓｃｏｎｔａｍｉｎａｔｅｄｂｙａｃｉｄｍｉｎｅｄｒａｉｎａｇｅｆｒｏｍｃｏｐｐｅｒｍｉｎｅ￥ＬｕａｎＺｈａｏｋｕｎ；ＣｈｅｎＭｉｎｇ；ＴａｎｇＨｏｎｇｘｉａｏ（Ｒｅｓｅａ...     

水中污染物对阳离子交换膜分离去除Cu2+的影响

基于Donnan dialysis原理,在无外加电压作用下采用阳离子交换膜分离去除原水中的Cu2+,研究原水中可能出现的无机颗粒物,有机物质,EDTA酸、氨水、Fe3+、表面活性剂等对阳离子交换膜分离去除Cu2+效果的影响.研究表明:原水中添加二氧化硅、腐殖酸、EDTA酸、氨水、Fe3+、表面活性剂等物质,在长时间运行后均会对离子交换膜去除Cu2+有不同程度的影响;二氧化硅和非离子表面活性剂等污染物不会和膜及Cu2+发生物理化学反应,对膜去除Cu2+效果影响较小,相比空白样,Cu2+去除率下降约4%;氨水、阴离子表面活性剂等会导致Cu2+发生沉淀反应,腐殖酸会吸附Cu2+,使原水中游离态Cu2+浓度显著降低约50%;EDTA酸、氨水、阴离子表面活性剂等会与Cu2+形成络合物,对去除Cu2+有严重影响,相比空白样, Cu2+去除率分别下降约100%(EDTA酸)、78%(氨水)、56%(阴离子表面活性剂);阳离子表面活性剂存在时,其会大量占据膜内空间,Cu2+基本无去除;Fe3+在弱酸性或中性水中会水解生成氢氧化铁胶体,对去除Cu2+有一定影响,相比空白样, Cu2+去除率下降约12%.     

Equilibrium and kinetics of copper(Ⅱ) biosorption by Myriophyllum spicatum L.

The potential use of Myriophyllum spicatum L. biomass as a biosorbent for the removal of copper（ Ⅱ ） from aqueous solution was investigated in laboratory condition. The sorption experiments were undertaken to obtain copper（ Ⅱ ） biosorption properties of M. spicatum L., i.e. equilibrium time, the maximum capacity, and rate constants. Copper（ Ⅱ ） biosorption was fast and equilibrium was attained within 35 min at initial copper（ Ⅱ ） concentration of 6 mg/L. Different isotherm models including the Langmuir, Freundlich, Temkin and Redlich-Peterson model, were used to investigate the sorption capacity and isotherm. These models showed an excellent match with the experimental data except for the Freundlich model. According to the Langmuir coefficients, the maximum sorption capacity of copper onto M. spicatum L. was 10.80 mg/g. The kinetics of copper（ Ⅱ ） sorption was also analysed and rate constants were derived. It was found that the overall sorption process was best described by the pseudo second-order equation, and that intraparticle diffusion was not the rate determining step. The results of this study showed that M. spicatum L. can be considered as useful vehicles for the removal and recovery of copper（ Ⅱ ） from aqueous solutions.     

铜渣与含砷污酸反应行为及除砷机理

分析铜渣组成结构和形貌特性的基础上,研究了铜渣与含砷污酸反应行为及脱砷规律,阐明了反应动力学过程,揭示了铜渣除砷机理.结果表明：在铜渣用量为0.2g/mL,反应温度为23℃,反应时间为24h的最优条件下,铜渣的最大去除容量达到25.89mg/g,除砷率达到99.56%,并且除砷后铜渣的砷浸出浓度低于5mg/L的危险废弃物界定限值,属于一般固体废弃物.铜渣除砷过程符合拟二级动力学模型,该过程受铁离子释放速度限制,离子交换吸附和化学沉淀方式同步进行实现了砷的脱除,两种方式的结合有利于砷的稳定化.铜渣与污酸反应释放大量的铁离子,通过离子交换吸附与砷酸根离子发生沉淀反应,形成较为稳定的砷酸盐及其衍生化合物,进而达到除砷目的.铜渣表现出优越的除砷性能,为重有色冶炼污酸处置提供了一种高效和低成本的方法.     

失效锂离子电池有机物真空脱除和浸出研究

文章采用真空蒸发热处理的方法脱除废弃失效的锂离子电池中的有机物,加热温度为220~500℃,真空炉内压力150Pa,恒温处理时间1h。除有机物被脱除外,当处理温度为280℃时形成了CoO和Li2CO3。温度升高至350℃时,主要的物相为LiCoO2、CoO、Co3O4和Co,以及少量Li2CO3。在超声场中将电极材料与铝、铜箔集流体分离,然后分别用含亚硫酸钠的硫酸溶液和氨性溶液处理电极材料。当用含亚硫酸钠的硫酸溶液浸出经280℃脱除有机物的电极材料时,钴元素基本被浸出。而用氨性溶液浸出经350℃脱除有机物的电极材料时,钴元素的浸出率很低。为了提高钴的浸出率,真空热处理的温度应介于280~350℃之间。     

短期暴露实验中铜在鱼鳃表面的结合状态

利用逐级提取的方法研究了短期暴露实验过程中鱼鳃表面不同结合状态的铜随时间变化的过程．考虑到实验过程中水环境条件的动态变化，对实验数据进行了校正．结果表明，鱼鳃对铜的吸收在3h左右达到稳态平衡，水提铜、鱼鳃表面易交换铜以及鱼鳃表面难交换铜随时间变化趋势一致。     

超声波促进Fenton法脱色甲基橙溶液的研究

分别研究了超声波、Fenton试剂、超声波-Fenton试剂作用下甲基橙溶液的脱色和COD去除行为.结果表明,超声波单独作用甲基橙溶液几乎没有脱色效果;Fenton试剂单独作用400mg/L的甲基橙溶液30min,甲基橙色度去除率67.51%,COD去除率63.15%;而超声波-Fenton试剂时,溶液色度去除率86.91%,COD去除率80.32%.超声波与Fenton试剂对甲基橙溶液的脱色和COD去除有协同作用.Fenton试剂脱色强酸性甲基橙溶液是氧化反应,而在pH大于5时,是还原反应.     

Preparation of organically functionalized silica gel as adsorbent for copper ion adsorption

A novel adsorbent (AMPS-silica) was synthesized by bounding AMPS (2-acrylamido-2-methylpropanesulfonic acid) onto silica surface, which functioned with -methacryloxypropyltrimethoxysilane reagent. The adsorbent was characterized by nitrogen adsorption/ desorption measurement, thermogravimetric analysis (TGA) and potentiometric titration analysis. The TGA result indicated that the surface modification reactions introduced some organic functional groups onto the surface of silica. The surface area of AMPSsilica was 389.7 m2/g. The adsorbent was examined for copper ion removal in series of batch adsorption experiments. Results showed that the adsorption of Cu2+ onto AMPS-silica was pH dependent, and the adsorption capacity increased with increasing pH from 2 to 6. The adsorption kinetics showed that Cu2+ adsorption was fast and the data fitted well with a pseudo second- order kinetic model. The adsorption of Cu2+ onto AMPS-silica obeyed both Freundlich and Langmuir isotherms, with r2 = 0.993 and r2 = 0.984, respectively. The maximum Cu2+ adsorption capacity was 19.9 mg/g. The involved mechanism might be the adsorption through metal binding with organic functional groups such as carboxyl, amino and sulfonic groups. Cu2+ loaded on AMPS-silica could be desorbed in HNO3 solution, and the adsorption properties remain stable after three adsorption-desorption cycles.     

具备微电解特性的改性泡沫铜去除强力霉素

通过改进的还原方法把纳米零价铁（nZVI）负载在多孔泡沫铜（CF）上,制备出具有微电解特性的泡沫铜材料（MCF）,并利用SEM,SEMMAPPING和EDX对其表面的形态特征及其元素分布进行了表征.考察了不同去除方式,不同MCF投加量和不同强力霉素（DC）初始浓度对降解效果的影响.结果表明：负载等量nZVI的MCF处理效果明显优于nZVI;当DC初始浓度为50mg/L,MCF的投加量为4.0g,反应20min时,DC去除率可达到99%;动力学分析表明,MCF降解DC符合准一级反应动力学,且随着MCF的投加量增加,反应速率常数k增大,投加量为5.0g时,k值最大为0.0609min^-1.