Investigation on the effect of sintering temperature on kaolin hollow fibre membrane for dye filtration

Despite its extraordinary price, ceramic membrane can still be able to surpass polymeric membrane in the applications that require high temperature and pressure conditions, as well as harsh chemical environment. In order to alleviate the high cost of ceramic material that still becomes one of the major factors that contributes to the high production cost of ceramic membrane, various attempts have been made to use low cost ceramic materials as alternatives to well-known expensive ceramic materials such as alumina, silica, and zirconia in the fabrication of ceramic membrane. Thus, local Malaysian kaolin has been chosen as the ceramic material in this study for the preparation of kaolin hollow fibre membrane since it is inexpensive and naturally abundant in Malaysia. Due to the fact that the sintering process plays a prominent role in obtaining the desired morphology, properties, and performances of prepared ceramic membrane, the aim of this work was to study the effect of different sintering temperatures applied (ranging from 1200 to 1500 °C) in the preparation of kaolin hollow fibre membrane via dry/wet phase inversion-based spinning technique and sintering process. The morphology and properties of membrane were then characterised by SEM, AFM, FTIR, XRD, and three-point bending test, while the performances of membrane were investigated by conducting water permeation and Reactive Black 5 (RB5) dye rejection tests. From the experimental results obtained, the sintering temperature of 1400 °C could be selected as the optimum sintering temperature in preparing the kaolin hollow fibre membrane with the dense sponge-like structure of separation layer that resulted in the good mechanical strength of 70 MPa with the appreciable water permeation of 75 L/h m² bar and RB5 rejection of 68%.     

Assessing demineralization treatments for PVC effluent reuse in the resin polymerization step

To reduce fresh water consumption in a polyvinyl chloride (PVC) plant, the effluent from a biological treatment must be demineralized to be re-used in the resin polymerization process. Demineralization is a critical process, since the quality and the stability of the PVC resins are highly influenced by the water quality used in the process. The main target values for water parameters are the following: conductivity <10 μScm^?1, TOC < 10 mg L^?1, and Al < 0.1 mg L^?1. To achieve this quality, several reverse osmosis membranes from different materials and suppliers were tested and compared in the demineralization treatment. Polyamide membranes showed higher salt rejection compared to cellulose acetate membranes yielding both types similar flux and permeability. Two-pass reverse osmosis treatment was necessary to reach conductivities lower than 10 μS cm^?1. On the other hand, a good quality effluent for reuse was obtained by combining RO and ionic exchange resins. Results showed that good quality PVC resins in terms of color, granulometry, porosity, and bulk density were obtained when demineralized water from two-pass reverse osmosis was used as fresh water, proving the feasibility of the effluent reuse in the PVC industry.     

印染废水回用微滤膜污染控制研究

采用PVDF中空纤维微滤膜处理某纺织印染厂二级生化出水,研究了膜污染控制及清洗方法。结果表明,合理的膜通量是控制膜污染、保证膜寿命的关键,采用31 L/(m2.h)左右的通量有助于膜污染的控制。氢氧化钠与次氯酸钠可分别用于日常维护清洗与恢复清洗,通过循环正洗不仅能满足清洗要求,且药剂使用量也小于反洗方法,每吨产水清洗用碱费用仅0.06元。化学清洗后再水力正洗,能进一步提高清洗效果。     

Preliminary toxicological assessment of phthalate esters from drinking water consumed in Portugal

This paper reports, for the first time, the concentrations of selected phthalates in drinking water consumed in Portugal. The use of bottled water in Portugal has increased in recent years. The main material for bottles is polyethylene terephthalate (PET). Its plasticizer components can contaminate water by leaching, and several scientific studies have evidenced potential health risks of phthalates to humans of all ages. With water being one of the most essential elements to human health and because it is consumed by ingestion, the evaluation of drinking water quality, with respect to phthalate contents, is important. This study tested seven commercial brands of bottled water consumed in Portugal, six PET and one glass (the most consumed) bottled water. Furthermore, tap water from Lisbon and three small neighbor cities was analyzed. Phthalates (di-n-butyl phthalate ester (DnBP), bis(2-ethylhexyl) phthalate ester (DEHP), and di-i-butyl phthalate ester (DIBP)) in water samples were quantified (PET and glass) by means of direct immersion solid-phase microextraction and ionic liquid gas chromatography associated with flame ionization detection or mass spectrometry due to their high boiling points and water solubility. The method utilized in this study showed a linear range for target phthalates between 0.02 and 6.5 μg L^?1, good precision and low limits of detection that were between 0.01 and 0.06 μg L^?1, and quantitation between 0.04 and 0.19 μg L^?1. Only three phthalates were detected in Portuguese drinking waters: dibutyl (DnBP), diisobutyl (DIBP), and di(ethylhexyl) phthalate (DEHP). Concentrations ranged between 0.06 and 6.5 μg L^?1 for DnBP, between 0.02 and 0.16 μg L^?1 for DEHP, and between 0.1 and 1.89 μg L^?1 for DIBP. The concentration of DEHP was found to be up to five times higher in PET than in glass bottled water. Surprisingly, all the three phthalates were detected in glass bottled water with the amount of DnBP being higher (6.5 μg L^?1) than in PET bottled water. These concentrations do not represent direct risk to human health. Regarding potable tap water, only DIBP and DEHP were detected. Two of the cities showed concentration of all three phthalates in their water below the limits of detection of the method. All the samples showed phthalate concentrations below 6 μg L^?1, the maximum admissible concentration in water established by the US Environmental Protection Agency. The concentrations measured in Portuguese bottled waters do not represent any risk for adult's health.     

Metal ferrite incorporated polysulfone thin-film nanocomposite membranes for wastewater treatment

Effluents from food, fermentation, and sugar industries contain a large quantity of glucose which has to be removed to limit the chemical oxygen demand (COD) of the water discharged. This work proposes novel thin-film nanocomposite (TFN) membranes incorporated with MgFe₂O₄ and ZnFe₂O₄ nanoparticles to address this concern. The nanoparticles synthesized by the sol–gel method was extensively characterized and then incorporated into the active polyamide layer of the thin-film composite polysulfone membranes. The change in membrane morphology, wettability, chemical structure, and mechanical strength with the incorporation of nanoparticles was studied in detail. Membranes with 0.005 wt.% MgFe₂O₄ nanoparticle exhibited highest glucose rejection (96.52?±?2.35%) at 10 bar, 25 °C, and sufficiently high pure water flux (50.54?±?1.92 L/m²h). This membrane also displayed 69.1?±?5.12% salt rejection when challenged with 2000 ppm synthetic NaCl solution.

     

Phenol removal from wastewater by adsorption on zeolitic composite

It is well known that adsorption is an efficient method of removal of various pollutants from wastewater. The present study examines the phenol removal from water by adsorption on a new material, based on zeolitic volcanic tuff. This compound contains zeolitic tuff and cellulose, another known adsorbent, in a mass ratio of 4 to 1. The performances of the new adsorbent composite were compared with those of a widely used adsorbent material, zeolitic volcanic tuff. The adsorbent properties were tested on batch synthetic solutions containing 1–10 mg L^?1 (1–10 ppm) phenol, at room temperature without pH adjustment. The influence of the adsorbent dose, pH and contact time on the removal degree of phenol from water was investigated. The experimental data were modeled using the Langmuir, Freundlich, and Temkin adsorption isotherms. The Langmuir model was found to best represent our data revealing a monolayer adsorption with a maximum adsorption capacity between 0.12 and 0.53 mg g^?1 at 25 °C, for 2.00 g of adsorbent, depending on the initial phenol concentration. The adsorption kinetic study was performed using a pseudo-first- and pseudo-second-order kinetic models illustrating that phenol adsorption on zeolite composite is well described by pseudo-first kinetic equations. Our results indicated that phenol adsorption on the new adsorbent composite is superior to that on the classic zeolite.     

Development of an In-Line System for the Analysis of 4,4′-DDT in Water

An in-line system for trace persistent organic pollutants (POPs) in water was developed by using a laboratory-made hollow fiber membrane (HFM) unit connected with a high-resolution gas chromatograph-mass spectrometer (HRGC-MS). The semivolatile organic compound, 4,4′-Dichlorodiphenyl trichloroethane (4,4′-DDT), was chosen as a representative of a persistent organic compound. The synthetic water contaminated with 4,4′-DDT was passed through the HFM unit, the extraction occurred by the analyte pervaporated and permeated, then stripped into HRGC-MS. Several factors were investigated for the high extraction efficiency. The best performance was obtained at sample and stripping gas flow rates of 6 and 9 mLmin^?1, respectively, and desorption temperature of 60°C. At this temperature, the diffusion rate was enhanced by 15 times over 25°C. A wide linear dynamic range was obtained, i.e., 0.10–1.0 mgL^?1, with a limit of detection (LOD) of 90 μgL^?1. The extraction efficiency of 4,4′-DDT in real water samples was in the range of 83–94%. Real water samples were analyzed and 0.6 μgL^?1 of 4,4′-DDT was found in unregistered bottled water and 7.0 μgL^?1 in tap water.     

TiO2光催化复合分离膜对水中天然有机物的去除

在水源污染越来越严重、水质标准日益严格的背景下,超滤(UF)已逐渐成为替代饮用水常规处理技术的最佳选择之一。本研究中采用相转化法,将聚偏氟乙烯(PVDF)、聚乙二醇(PEG)和二氧化钛(TiO₂)共混制得光催化复合分离膜并对其进行扫描电子显微镜(SEM)、原子力显微镜(AFM)和X射线能谱仪(EDS)等相应的表征。比较了有无光照条件下,PVDF-PEG和PVDF-PEG-TiO₂膜对腐殖酸(HA)的截留和超滤过程中的膜污染情况。研究结果表明,TiO₂光催化复合分离膜能提高对水中天然有机物的去除并同时降低膜污染。紫外光照强度越强,PVDF-PEG-TiO₂膜的抗污染性能越好。另外,光催化能更有效地减少超滤初始浓度较低的腐殖酸溶液过程中的膜通量衰减。     

Solar CPC pilot plant photocatalytic degradation of bisphenol A in waters and wastewaters using suspended and supported-TiO2. Influence of photogenerated species

Photocatalytic degradation of bisphenol A (BPA) in waters and wastewaters in the presence of titanium dioxide (TiO₂) was performed under different conditions. Suspensions of the TiO₂ were used to compare the degradation efficiency of BPA (20 mg L^?1) in batch and compound parabolic collector (CPC) reactors. A TiO₂ catalyst supported on glass spheres was prepared (sol–gel method) and used in a CPC solar pilot plant for the photodegradation of BPA (100 μg L^?1). The influence of OH·, O₂ ^·?, and h ⁺ on the BPA degradation were evaluated. The radicals OH· and O₂ ^·? were proved to be the main species involved on BPA photodegradation. Total organic carbon (TOC) and carboxylic acids were determined to evaluate the BPA mineralization during the photodegradation process. Some toxicological effects of BPA and its photoproducts on Eisenia andrei earthworms were evaluated. The results show that the optimal concentration of suspended TiO₂ to degrade BPA in batch or CPC reactors was 0.1 g L^?1. According to biological tests, the BPA LC₅₀ in 24 h for E. andrei was of 1.7?×?10^?2 mg cm^?2. The photocatalytic degradation of BPA mediated by TiO₂ supported on glass spheres suffered strong influence of the water matrix. On real municipal wastewater treatment plant (MWWTP) secondary effluent, 30 % of BPA remains in solution; nevertheless, the method has the enormous advantage since it eliminates the need of catalyst removal step, reducing the cost of treatment.     

Adsorptive removal and photocatalytic decomposition of sulfamethazine in secondary effluent using TiO2–zeolite composites

We investigated the adsorption and decomposition of sulfamethazine (SMT), which is used as a synthetic antibacterial agent and discharged into environmental water, using high-silica Y-type zeolite (HSZ-385), titanium dioxide (TiO₂), and TiO₂–zeolite composites. By using ultrapure water and secondary effluent as solvents, we prepared SMT solutions (10 μg/L and 10 mg/L) and used them for adsorption and photocatalytic decomposition experiments. When HSZ-385 was used as an adsorbent, rapid adsorption of SMT in the secondary effluent was confirmed, and the adsorption reached equilibrium within 10 min. The photocatalytic decomposition rate using TiO₂ in the secondary effluent was lower than that in ultrapure water, and we clarified the inhibitory effect of ions and organic matter contained in the secondary effluent on the reaction. We synthesized TiO₂–zeolite composites and applied them to the removal of SMT. During the treatment of 10 μg/L SMT in the secondary effluent using the composites, 76 % and more than 99 % of the SMT were decomposed within 2 and 4 h by photocatalysis. The SMT was selectively adsorbed onto high-silica Y-type zeolite in the composites. Resultantly, the inhibitory effect of the coexisting materials was reduced, and the composites could remove SMT more effectively compared with TiO₂ alone in the secondary effluent.     

A novel low-cost detection method for screening of arsenic in groundwater

In the present work, a novel and simple detection system for As inorganic species contained in groundwater is presented. To reach the required detection limit, the proposed methodology is based on two steps: first is the transport and preconcentration of the inorganic arsenic species using a polymer inclusion membrane (PIM) system and second is the formation of a coloured complex, the  absorbance of which is measured. Different parameters related to the membrane composition and the transport kinetics have been studied, and it was found that membranes made of polyvinyl chloride (PVC) as a polymer, and Aliquat 336 as a carrier, ensured efficient arsenic transport when the carrier content was at least 31 % (w/w). The implementation of the designed PIM in a special device that contained only 5 mL of the stripping solution (0.1 M NaCl) allowed As preconcentration from a 100-mL water sample, thus facilitating its detection with the colorimetric method. The new method developed here was validated, and its analytical figures of merit were determined, i.e. limit of detection of 4.5 μg L^?1 at 820 nm and a relative standard deviation within the range 8–10 %. Finally, the method was successfully applied to the analysis of different water samples from Catalonia region with naturally occurring As.     

Color removal from wastewater using a synthetic high-performance antifouling GO-CPTMS@Pd-TKHPP/polyether sulfone nanofiltration membrane

Modified graphene oxide with 5,10,15,20-tetrakis-(4-hexyloxyphenyl)-porphyrin and palladium (II) (signified by GO-CPTMS@Pd-TKHPP) prepared as a novel antifouling polyether sulfone (PES) blended nanofiller membrane. The membrane efficiency has been analyzed such as pure water flux (PWF), hydrophilicity, and antifouling features. By increasing of modified graphene oxide percentage from 0 to 0.1 wt.% in the polymer matrix, the PWF was incremented from 14.35 to 37.33 kg/m²·h at 4 bar. The membrane flux recovery ratio (FRR) has been investigated by applying powdered milk solution; the FRR results indicated that the 0.1 wt.%-modified graphene oxide membrane showed a positive effect on fouling behavior with Rir and FRR value 8.24% and 91.76%, respectively. The nanofiltration membrane performance was assessed applying the Direct Red 16 dye rejection. It was demonstrated that the optimal membranes (0.1 wt.%-modified graphene oxide) had notable dye removal (99.58% rejection). The results are also verified by measuring the scanning electron microscopy (SEM), water contact angle (WCA), and atomic microscopy analysis (AFM).

     

Dietary arsenic consumption and urine arsenic in an endemic population: response to improvement of drinking water quality in a 2-year consecutive study

We assessed the association between arsenic intake through water and diet, and arsenic levels in first morning-void urine under variable conditions of water contamination. This was done in a 2-year consecutive study in an endemic population. Exposure of arsenic through water and diet was assessed for participants using arsenic-contaminated water (≥50 μg L^?1) in a first year (group I) and for participants using water lower in arsenic (<50 μg L^?1) in the next year (group II). Participants with and without arsenical skin lesions were considered in the statistical analysis. Median dose of arsenic intake through drinking water in groups I and II males was 7.44 and 0.85 μg kg body wt.^?1 day^?1 (p <0.0001). In females, it was 5.3 and 0.63 μg kg body wt.^?1 day^?1 (p <0.0001) for groups I and II, respectively. Arsenic dose through diet was 3.3 and 2.6 μg kg body wt.^?1 day^?1 (p?=?0.088) in males and 2.6 and 1.9 μg kg body wt.^?1 day^?1 (p?=?0.0081) in females. Median arsenic levels in urine of groups I and II males were 124 and 61 μg L^?1 (p?=?0.052) and in females 130 and 52 μg L^?1 (p?=?0.0001), respectively. When arsenic levels in the water were reduced to below 50 μg L^?1 (Indian permissible limit), total arsenic intake and arsenic intake through the water significantly decreased, but arsenic uptake through the diet was found to be not significantly affected. Moreover, it was found that drinking water mainly contributed to variations in urine arsenic concentrations. However, differences between male and female participants also indicate that not only arsenic uptake, but also many physiological factors affect arsenic behavior in the body and its excretion. As total median arsenic exposure still often exceeded 3.0 μg kg body wt.^?1 day^?1 (the permissible lower limit established by the Joint Expert Committee on Food Additives) after installation of the drinking water filters, it can be concluded that supplying the filtered water only may not be sufficient to minimize arsenic availability for an already endemic population.     

TiO2光催化复合分离膜对水中天然有机物的去除

在水源污染越来越严重、水质标准日益严格的背景下，超滤（UF）已逐渐成为替代饮用水常规处理技术的最佳选择之一。本研究中采用相转化法，将聚偏氟乙烯（PVDF）、聚乙二醇（PEG）和二氧化钛（TiO2）共混制得光催化复合分离膜并对其进行扫描电子显微镜（SEM）、原子力显微镜（AFM）和X射线能谱仪（EDS）等相应的表征。比较了有无光照条件下，PVDF-PEG和PVDF—PEG—TiO2膜对腐殖酸（HA）的截留和超滤过程中的膜污染情况。研究结果表明，TiO2光催化复合分离膜能提高对水中天然有机物的去除并同时降低膜污染。紫外光照强度越强，PVDF-PEG—TiO2膜的抗污染性能越好。另外，光催化能更有效地减少超滤初始浓度较低的腐殖酸溶液过程中的膜通量衰减。     

Novel pipette-tip graphene/poly (vinyl alcohol) cryogel composite extractor for the analysis of carbofuran and carbaryl in water

A novel pipette-tip extractor of a graphene/poly (vinyl alcohol) cryogel (graphene/PVA) composite sorbent was prepared to preconcentrate carbamate pesticides in environmental water samples before analysis with a gas chromatograph-flame ionization detector (GC-FID). This novel pipette-tip extractor with the graphene/PVA sorbent exhibited a high porosity when observed through a scanning electron micrograph (SEM). Under optimal conditions, using only 1.0 mL of sample and 0.75 mL of eluting solvent, the developed method provided a wide linear range of 10–700 ng mL^?1 and 10–500 ng mL^?1 with limit of detection (LOD) of 6.40 ± 0.18 and 9.17 ± 0.34 ng mL^?1 for carbofuran (2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate) and carbaryl (1-naphthyl methylcarbamate), respectively. The pipette-tip extractor provided high extraction efficiency with high accuracy indicated, by good recoveries in the range of 74.5 ± 4.8% to 119.7 ± 1.6% and 76 ± 15% to 114 ± 19% for carbofuran and carbaryl, respectively. In addition, the fabrication procedure showed a good pipette-tip extractor-to-pipette-tip extractor reproducibility with a relative standard deviation of 1.3–9.8% (n = 5). When the developed pipette-tip extractor was applied for the extraction of carbofuran and carbaryl in surface water samples near vegetable plantation areas, 25.9 ± 8.2 ng mL^?1 of carbofuran was found, and carbaryl was also detected in concentrations that ranged from 45.0 ± 4.0 to 191 ± 13 ng mL^?1.     

Rapid and Sensitive LC/MS/MS Direct Injection Method for the Determination of Trace Level Corexit EC9500A Oil Dispersant in Seawater

A rapid and sensitive liquid chromatography tandem mass spectrometry (LC/MS/MS) method for the determination of trace dioctyl sulfosuccinate (DOSS) concentrations in seawater samples has been established. The method is well suited to aquatic environment impact monitoring following application of the dispersant Corexit EC9500A. Linearity of the method was demonstrated down to 0.05 ng/mL^?1 (0.05 µgL^?1) DOSS in seawater, with a 2.4% relative standard deviation precision for preparation replicates. A US EPA method limit of detection of <0.02 ng/mL^?1 (<0.02 µgL^?1) was calculated and specificity was confirmed by monitoring of two qualifier ions at 291.1 m/z and 227.1 m/z. These transitions were confirmed by QToF analysis to be associated with the DOSS precursor ion at 421.2 m/z. For application to seawater samples and samples containing oil particulates, a practical and repeatable calibration range of 0.5 ng/mL^?1 (0.5 µgL^?1) to 25.0 ng/mL^?1 (25.0 µgL^?1) DOSS is reported. The method was shown to have excellent precision and accuracy, with a consistent ≤1.6% relative standard deviation for system suitability standards at 0.5 ng/mL^?1 (0.5 µgL^?1) and linear weighted (1/x) regression coefficients of determination ≥0.995. The surfactant nature of the analyte is discussed in relation to detection limit and loss of analyte. Speculation of a relationship between DOSS in association or aggregation with divalent cations, such as Ca²⁺ present in salt water and hard water, is suggested. The consequent effects on cell ionic balance and membrane function are discussed.     

Residues of carbosulfan and its metabolites carbofuran and 3-hydroxy carbofuran in rice field ecosystem in China

The fate of carbosulfan (seed treatment dry powder) was studied in rice field ecosystem, and a simple and reliable analytical method was developed for determination of carbosulfan, carbofuran, and 3-hydroxyl carbofuran in brown rice, rice straw, paddy water, and soil. The target compounds were extracted using acetonitrile or dichloromethane, cleaned up on acidic alumina or florisil solid phase extraction (SPE) cartridge, and analyzed by gas chromatography. The average recoveries of carbosulfan, carbofuran and 3-hydroxy carbofuran in brown rice, rice straw, paddy water, and soil ranged from 72.71% to 105.07%, with relative standard deviations of 2.00–8.80%. The limits of quantitation (LOQs) of carbosulfan, carbofuran and 3-hydroxy carbofuran in the samples (brown rice, rice straw, paddy water and soil) were 0.011, 0.0091, 0.014, 0.010 mg kg^?1, 0.016, 0.019, 0.025, 0.013 mg kg^?1, and 0.031, 0.039, 0.035, 0.036 mg kg^?1, respectively. The trials results showed that the half-lives of carbosulfan, carbofuran and 3-hydroxy carbofuran in rice straw were 4.0, 2.6 days, 3.9, 6.0 days, and 5.8, 7.0 days in Zhejiang and Hunan, respectively. Carbosulfan, carbofuran and 3-hydroxy carbofuran were detected in soils. Carbosulfan and 3-hydroxy carbofuran were almost undetectable in paddy water. Carbofuran was detected in paddy water. The final residues of carbosulfan, carbofuran and 3-hydroxy carbofuran in brown rice were lower than 0.05 mg kg^?1, which were lower than 0.5 mg kg^?1 (MRL of carbosulfan) or 0.1 mg kg^?1 (MRL of carbofuran). Therefore, a dosage of 420 g active ingredient per 100 kg seed was recommended, which could be considered as safe to human beings and animals. These would contribute to provide the scientific basis of using this insecticide.     

Selective sensing of mercury(II) using PVC-based membranes incorporating recently synthesized 1,3-alternate thiacalix[4]crown ionophore

The construction and electrodes characteristics of poly(vinylchloride) (PVC)-based polymeric membrane electrode (PME) and coated graphite electrode (CGE), incorporating 1,3-alternate thiacalix[4]crown as ionophore for estimation of Hg(II) ions, are reported here. The best potential response was observed for PME-1 having membrane composition of: ionophore (6.2 mg), PVC (100.0 mg), 2-nitrophenyl octyl ether (2-NPOE; 200.0 mg), and sodium tetraphenyl borate (NaTPB; 2.0 mg); for CGE-1 with the membrane composition: ionophore (3.5 mg), PVC (40.0 mg), 2-NPOE (80.0 mg), and NaTPB (2.0 mg). The electrodes exhibits Nernstian slope of 29.16 mV/decade with PME-1 and 30.39 mV/decade with CGE-1 for Hg(II) ions over wide concentration range, i.e., 1.0?×?10^?1 to 5.0?×?10^?6?M with PME-1 and 1.0?×?10^?1 to 5.0?×?10^?7?M with CGE-1. Lower detection limits were found to be 9.77?×?10^?6?M for PME-1 and 7.76?×?10^?7?M for CGE-1 with response time varying from 10 to 20 s. Also, these electrodes work within pH range of 2.0–6.0 for PME-1 and 1.5–6.5 for CGE-1. Overall, CGE-1 has been found to be better than PME-1. CGE-1 has been used as indicator electrode for the potentiometric titration of Hg(II) ions with EDTA as well as successfully applied for determination of Hg(II) content in wastewater, insecticide, dental amalgam, and ayurvedic medicines samples with very good performance (0.9974 correlation coefficient in the comparison against volumetric method).     

Mobility and efficacy of 2,4-D herbicide from slow-release delivery systems based on organo-zeolite and organo-bentonite complexes

This research aimed to develop slow-release formulations (SRFs) of 2,4-dichlorophenoxyacetic acid (2,4-D) using zeolite and bentonite minerals modified with cetyltrimethylammonium (CTMA) surfactant. Adsorption–desorption, greenhouse bioassay and column experiments were carried out to assess the potential of the SRFs to control weeds while reducing the herbicide leaching losses to deep layers of soil. The results showed that only 6.5 mmol 2,4-D kg^?1 was retained by Na-bent, and the herbicide was not adsorbed by Na-zeol at all. The surface modification with CTMA surfactant, however, improved the 2,4-D adsorption capacity of the zeolite and bentonite up to 207.5 and 415.8 mmol kg^?1, respectively. The synthesized organo-minerals slowly released the retained 2,4-D discharging 22 to 64% of the adsorbed 2,4-D to the solution phase within 7 days. The SRFs significantly (P = 0.05) reduced the herbicide mobility within the soil columns keeping a great portion of the herbicide active ingredient in the upper 5 cm soil layer. The SRFs were significantly (P = 0.05) as effective as the free technical herbicide in weed control without harming the ryegrass as the main plant. Therefore, the synthesized SRFs could be considered as useful tools for weed control in sustainable agriculture.     

Identification and quantitative detection of Legionella spp. in various aquatic environments by real-time PCR assay

In this study, a SYBR green quantitative real-time PCR was developed to quantify and detect the Legionella spp. in various environmental water samples. The water samples were taken from watershed, water treatment plant, and thermal spring area in Taiwan. Legionella was detected in 13.6 % (24/176), and the detection rate for river water, raw drinking water, and thermal spring water was 10, 21.4, and 16.6 %, respectively. Using real-time PCR, concentration of Legionella spp. in detected samples ranged between 9.75?×?10⁴ and 3.47?×?10⁵?cells/L in river water, 6.92?×?10⁴ and 4.29?×?10⁵?cells/L in raw drinking water, and 5.71?×?10⁴ and 2.12?×?10⁶?cells/L for thermal spring water samples. The identified species included Legionella pneumophila (20.8 %), Legionella jordanis (4.2 %), Legionella nautarum (4.2 %), Legionella sp. (4.2 %), and uncultured Legionella sp. (66.6 %). The presence of L. pneumophila in aquatic environments suggested a potential public health threat that must be further examined.