TiO_2纳米管阵列光电极的制备及光催化性能研究

采用阳极氧化法在不同的条件下制备了TiO2纳米管阵列（TNT）光电极,利用SEM、XRD等手段对电极的表面形貌、晶体结构进行了分析和表征。以Rh.B为目标污染物,研究了不同电极的光催化和光电催化性能。结果表明：当氧化电压为20 V时,可获得形貌规则的有序排列的TiO2纳米管光电极,纳米管管径为80～120 nm;经50...     

制备条件对二氧化钛纳米管光电催化性能的影响研究

采用电化学阳极氧化法制备二氧化钛纳米管(TNT),通过改变氧化时间和氧化电压来制备具有不同形貌结构的TNT,并探讨不同条件下制备的TNT对模拟污染物甲基橙的光电催化降解活性.结果表明,当氧化电压由45 V增加到60 V时,相同氧化时间下制得的TNT的管长、管径、长径比都明显增加,而管壁厚均相应减小,氧化时间和氧化电压对制得的TNT的管长、管径和管壁厚等形貌特征有着重要的影响;在45 V、4h,60 V、3h和60 V、6h下制备的TNT具有较佳的形貌结构(管长分别为12.41、20.35、25.85 μm,长径比分别为110、166、178),其中又以60 V、6h时制备的TNT具有最佳的光电催化活性,其光电催化降解甲基橙的表观拟一级动力学速率常数为2.26×10-3 min-1;相关性分析结果表明,TNT的长径比对其光电催化活性有着极重要的影响.     

网络版论文摘要

正纳米TiO2电极的制备及电化学降解邻硝基苯酚张平解慧玲杨周生(安徽师范大学环境科学与工程学院,安徽芜湖241003)采用阳极氧化技术在钛片表面制备出纳米TiO2,并通过扫描电子显微镜(SEM)对其进行表征。利用制备的Ti/TiO2电极作为阳极、以Pt丝电极作为阴极,电化学降解邻硝基苯酚。使用紫外—可见光谱和液相色谱技术,对降解     

V/Ce共掺杂TiO2光催化降解甲醛的实验研究

采用溶胶-凝胶法制备了不掺杂、V掺杂、Ce掺杂、V/Ce共掺杂纳米TiO2光催化剂,并将其分别负载于瓷砖上,利用X射线衍射分析（XRD）和扫描电镜分析（SEM）技术对薄膜样品的结构和形貌进行了表征。通过对甲醛的降解实验评价光催化剂的光催化活性。实验结果表明,光催化剂的负载量、共掺杂离子的掺杂量、掺杂配比、煅烧温度影响纳米TiO2的光催化活性。V/Ce共掺杂TiO2光催化剂产生了协同效应,其光催化活性优于纯TiO2和单掺杂TiO2样品。     

网络版论文摘要

<正>锰离子掺杂对TiO 2纳米管光降解的影响刘长鑫钟玉荣徐宝龙(烟台大学电信息科学与技术学院,山东省高校光信息与光功能材料重点实验室,山东烟台264005)用阳极氧化法制备了TiO 2纳米管阵列,并通过热处理和电镀的方法实现了TiO 2纳米管的锰离子掺杂。场发射扫描电镜(FESEM)形貌分析显示其管径均匀排列,粉末X射     

纳米TiO2光催化氧化去除水中痕量双氯芬酸的研究

以TiCl4为前驱体,采用水解法经不同温度煅烧制备了具有不同理化性能的纳米TiO2光催化剂。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、物理吸附仪、紫外—可见光漫反射吸收光谱(UV-Vis DRS)等手段对纳米TiO2的晶相结构、粒径、孔径分布以及禁带宽度等进行了表征。以蒸馏水配制的双氯芬酸溶液为目标物,进行了纳米TiO2光催化氧化去除双氯芬酸的活性测试,研究了纳米TiO2的理化性能与光催化氧化活性之间的关系。结果表明,经400℃煅烧制得的纳米TiO2样品具有最高的光催化氧化活性,其在紫外光照射60min下对双氯芬酸的去除率为98%左右,比单独紫外光照射高出85百分点。纳米TiO2光催化氧化去除双氯芬酸的反应近似一级反应动力学模型,其中经400℃煅烧制得的纳米TiO2光催化氧化去除双氯芬酸的表观反应速率常数为0.054 54min-1,是普通商用TiO2的2倍左右,与德国Degussa P-25TiO2的光催化氧化活性最相近。     

可见光光电-Fenton体系中TiO2薄膜电极的制备及应用

采用可见光光电-Fenton体系对罗丹明B模拟废水进行处理。探讨了自制电解液、阳极氧化时间、煅烧温度、煅烧时间因素对阳极材料-TiO2薄膜电极的制备的影响,以及以此为阳极材料的可见光光电-Fenton体系对污染物的降解效果和光电协同作用,并通过响应面优化实验对制备条件优化。在单因素实验得到了参数取值的粗略范围的基础上,通过响应面优化实验得到了最优的制备条件:电解液0.5%NH4F丙三醇溶液、阳极氧化时间93.26 min、煅烧温度602.89℃、煅烧时间127.49 min,模拟出在该条件下的光电-Fenton去除率为70.78%;对此条件下的TiO2薄膜电极进行光催化和电-Fenton实验,得到光电协同因子为1.92;各因素对光电-Fenton去除率影响大小关系为:阳极氧化时间>煅烧时间>煅烧温度。响应面模型3次验证实验的误差均在5%以内,模型可用。     

纳米TiO2薄膜在不同陶瓷表面的负载及其光催化性能研究

利用2种不同表面处理的陶瓷作为载体,用溶胶凝胶法在其表面进行了纳米TiO2光催化薄膜的负载.采用X射线衍射法(XRD)、X射线光电子能谱仪(XPS)和扫描电镜(SEM)对薄膜的粒径、横断面及表面组成进行了表征和分析,结果表明,TiO2的平均粒径约为15 nm,釉面陶瓷TiO2薄膜分布均匀,膜厚约为300 nm;无釉陶瓷TiO2薄膜分布不均,膜层不明显;2种载体中的一些基质离子在TiO2薄膜有渗透.苯酚的降解实验表明,以2种不同表面处理的陶瓷为载体的TiO2薄膜对苯酚的降解均符合一级反应动力学,就催化活性而言,TiO2/釉面陶瓷＞TiO2/无釉陶瓷,分析认为基质渗透的Ca2 有降低TiO2光催化活性的作用;该薄膜对实际生产多菌灵废水具有催化降解作用.重复降解实验20次,TiO2/釉面陶瓷和TiO2/无釉陶瓷对苯酚的去除率仅分别降低9%和6%.     

纳米二氧化钛的改性及光催化氧化烷烃研究

催化剂的表面结构是影响催化反应的重要因素之一.利用原位红外(In-situ FT-IR)、X射线衍射(XRD)和紫外-可见漫反射(UV-Vis DRS)等现代物理技术考察了热处理改性对纳米 TiO2的表面结构、晶相结构、粒子大小、比表面积和吸光性能的影响,采用In-situ FT-IR光谱着重研究了纳米TiO2催化剂上环己烷光催化降解机制及催化剂的结构特性与催化反应之间的相关性.研究表明,400 ℃条件下热处理纳米TiO2具有最佳光催化活性,适宜的表面结构、晶相结构、吸光能力及晶化度是纳米TiO2光催化剂高催化活性的主要原因.借助In-situ FT-IR光谱,观察到环己烷氧化的主要产物是CO2和H2O,同时捕捉到了中间产物CO以及乙酸,提出了环己烷光催化降解的可能机理.     

纳米复合ZnO-TiO2晶体的制备及其光电催化性能研究

采用溶胶-凝胶法制备了纳米复合半导体ZnO-TiO2薄膜,并进行了结构和光电催化性能的测试.TiO2薄膜对五氯酚溶液的光电催化降解结果表明当输入正向偏压后,其光催化性能有较大提高.由于ZnO的掺入,半导体薄膜电极的光吸收能力增强;同时,Zn2+可能作为光生载流子的浅俘获中心,导致表面界面电荷转移加速,从而延长光生电子/空穴对的寿命并抑制其复合,有效地提高了TiO2薄膜光电催化活性.     

Field and laboratory studies of the fate and enantiomeric enrichment of venlafaxine and O-desmethylvenlafaxine under aerobic and anaerobic conditions

The stereoselectivity of R,S-venlafaxine and its metabolites R,S-O-desmethylvenlafaxine, N-desmethylvenlafaxine, O,N-didesmethylvenlafaxine, N,N-didesmethylvenlafaxine and tridesmethylvenlafaxine was studied in three processes: (i) anaerobic and aerobic laboratory scale tests; (ii) six wastewater treatment plants (WWTPs) operating under different conditions; and (iii) a variety of wastewater treatments including conventional activated sludge, natural attenuation along a receiving river stream and storage in operational and seasonal reservoirs. In the laboratory and field studies, the degradation of the venlafaxine yielded O-desmethylvenalfaxine as the dominant metabolite under aerobic and anaerobic conditions. Venlafaxine was almost exclusively converted to O-desmethylvenlafaxine under anaerobic conditions, but only a fraction of the drug was transformed to O-desmethylvenlafaxine under aerobic conditions. Degradation of venlafaxine involved only small stereoisomeric selectivity. In contrast, the degradation of O-desmethylvenlafaxine yielded remarkable S to R enrichment under aerobic conditions but none under anaerobic conditions. Determination of venlafaxine and its metabolites in the WWTPs agreed well with the stereoselectivity observed in the laboratory studies. Our results suggest that the levels of the drug and its metabolites and the stereoisomeric enrichment of the metabolite and its parent drug can be used for source tracking and for discrimination between domestic and nondomestic wastewater pollution. This was indeed demonstrated in the investigations carried out at the Jerusalem WWTP.     

骆马湖富营养化和生态状况调查与评价

为了了解骆马湖水质状况，在2005年对骆马湖富营养化状态和生态特性进行了调查，并结合“十五”期间的监测资料进行了分析。2005年骆马湖水体中总氮和总磷的平均值超《地表水环境质量标准》（GB3838-2002）中Ⅲ类，超标情况分别为0．78倍和0．54倍，达到湖库特定项目Ⅳ类水标准，骆马湖处于轻度富营养化状态。对骆马湖生态特征分析表明，由于该湖泊的形态以及“藻型浊水状态”和“泥沙型浊水状态”交替出现，遏制了湖水从高营养盐含量向全面富营养化状态演变，保障了底栖动物的良好生长环境，从而形成了骆马湖独特的环境生态平衡。     

Copper-catalyzed chlorination and condensation of acetylene and dichloroacetylene

The chlorination and condensation of acetylene at low temperatures is demonstrated using copper chlorides as chlorinated agents coated to model borosilicate surfaces. Experiments with and without both a chlorine source and borosilicate surfaces indicate the absence of gas-phase and gas-surface reactions. Chlorination and condensation occur only in the presence of the copper catalyst. C₂ through C₈ organic products were observed in the effluent; PCDD/F were only observed from extraction of the borosilicate surfaces. A global reaction model is proposed that is consistent with the observed product distributions. Similar experiments with dichloroacetylene indicate greater reactivity in the absence of the copper catalyst. Reaction is observed in the gas-phase and in the presence of borosilicate surfaces at low temperatures. The formation of hexachlorobenzene is only observed in the presence of a copper catalyst. PCDD/F were only observed from extraction of the borosilicate surfaces. A global reaction model is proposed for the formation of hexachlorobenzene from dichloroacetylene.     

Aerobic and anaerobic degradation of profluralin and trifluralin

Abstract

The degradation of profluralin [N‐(cyclopropylmethyl)‐α,α,α‐trifluoro‐2,6‐dinitro‐N‐propyl‐]p‐toluidine] and trifluralin (α,α,α‐trifluoro‐2,6‐dinitro‐N,N‐dipropyl‐p‐toluidine) was studied under aerobic and anaerobic soil conditions. Three soils (Goldsboro loamy sand, Cecil loamy sand, Drummer clay loam) were each treated with 1 ppmw herbicide; anaerobic conditions were maintained by flooding. Soil samples were extracted monthly and subjected to TLC analysis. No degradation was detected in sterile controls. Aerobic degradation of both herbicides was greatest in the Cecil loamy sand soil over the entire incubation period. Degradation of profluralin in Cecil soil under aerobic conditions was 86 percent after 4 months with three products detected; 83 percent of the trifluralin was degraded with two products detected. Anaerobic degradation accounted for 72 percent of the profluralin and 78 percent of the trifluralin after 4 months. Degradation of both herbicides increased with incubation time for the first 3 months and decreased slightly thereafter. Generally there was more extensive degradation (percent and in number of products formed) of profluralin than trifluralin under the conditions tested. More degradation products were detected for both herbicides under aerobic conditions than under anaerobic conditions.     

剩余污泥浓缩脱水投药量优化和模型建立

应用高分子阳离子絮凝剂（CPF-100）和聚丙烯酰胺（PAM）对污水厂剩余污泥进行浓缩脱水实验,研究表明：CPF-100的浓缩脱水效果优于PAM;当CPF-00投加量为1．16‰时,污泥沉降性能改善程度为37．51％;且在CPF-100投加量逐渐增大的初始阶段,污泥沉降性能改善程度随投加量的增加而增大,但CPF-100投加量也不宜过大,当CPF-100投加量超过1．16‰后,反而会使浓缩脱水效果变差。同时,建立了污泥沉降性能改善程度与絮凝剂CPF-100投加量、沉降时间之间的数学模型,其能较好地反映污水厂剩余污泥的浓缩脱水效果。     

Sources and distribution of polychlorinated-dibenzo-p-dioxins and -dibenzofurans in soil and sediment from the Yellow Sea region of China and Korea

Polychlorinated-dibenzo-p-dioxins and -dibenzofurans (PCDD/Fs) were measured in soils and sediments from the Yellow Sea region. Korean soils and sediments mostly contained detectable PCDD/Fs and showed a widespread distribution among locations. Soil and sedimentary PCDD/Fs from China were comparable to or less than those in Korea. The patterns of relative concentrations of individual congeners in soils were different between the two countries, but similar in sediments. Sources of PCDD/Fs in China and Korea were found to be independent of each other and their distributions reflected matrix-dependent accumulation. Spatial distribution indicated some point sources in Korea while Chinese sources were more widespread and diffuse. PCDD/Fs measured in the coastal areas of the Yellow Sea were comparable to or less than those previously reported in for eastern Asia. However, ∑TEQs in soils and sediments were near to or, in some cases exceeded environmental quality guidelines.     

Quantification of carbamazepine and atrazine and screening of suspect organic contaminants in surface and drinking waters

A new approach for the identification of suspect trace organic contaminants in drinking and surface waters is presented. Samples were initially analyzed using a target determination method for two contamination tracers, carbamazepine (CBZ) and atrazine (ATZ). This method used offline solid-phase extraction and online solid-phase extraction techniques coupled to liquid chromatography-triple quadrupole mass spectrometry to accelerate the sample preparation process and improve method performance. CBZ and ATZ were found respectively in 31% and 56% of the samples, and concentrations were usually <20 ng L⁻¹. These samples were re-analyzed with a similar method on a quadrupole time-of-flight mass spectrometer to identify suspect contaminants by means of exact mass measurements and isotope patterns. A database of 264 common organic contaminants was built and used in conjunction with a Molecular Feature algorithm to identify the presence of these substances in drinking and surface water collected from different sources at various locations across Canada. Several organic contaminants were identified in the samples, but only the presence of caffeine, desethylatrazine, simazine and venlafaxine could be verified by comparison to pure standards. The presence of desethylatrazine was also confirmed by MS/MS experiments. These results suggest that target analysis for tracers of organic contamination may be a helpful tool to prioritize samples which should be further screened for suspect contaminants. This study also shows that the combination of separation techniques (offline and online SPE, LC) contribute to advance the applicability of high-resolution mass spectrometry for the identification of trace organic contaminants by accelerating the preparation step, reducing complexity and increasing analyte concentrations for optimal detection.     

Effects of compositional heterogeneity and nanoporosity of raw and treated biomass-generated soot on adsorption and absorption of organic contaminants

A biomass-generated soot was sequentially treated by HCl-HF solution, organic solvent, and oxidative acid to remove ash, extractable native organic matter (EOM), and amorphous carbon. The compositional heterogeneity and nano-structure of the untreated and treated soot samples were characterized by elemental analysis, thermal gravimetric analysis, BET-N₂ surface area, and electron microscopic analysis. Sorption properties of polar and nonpolar organic pollutants onto the soot samples were compared, and individual contributions of adsorption and absorption were quantified. The sorption isotherms for raw sample were practically linear, while were nonlinear for the pretreated-soot. The removal of EOM enhanced adsorption and reduced absorption, indicating that EOM served as a partitioning phase and simultaneously masked the adsorptive sites. By drastic-oxidation, the outer amorphous carbon and the inner disordered core of the soot particles were completely removed, and a fullerene-like nanoporous structure (aromatic shell) was created, which promoted additional π-π interaction between phenanthrene and the soot.     

Sorption and Desorption Behavior of Chloroanilines and Chlorophenols on Montmorillonite and Kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Persistence and dissipation kinetics of trifloxystrobin and tebuconazole in onion and soil

The persistence and dissipation kinetics of trifloxystrobin and tebuconazole on onion were studied after application of their combination formulation at a standard and double dose of 75 + 150 and 150 + 300 g a.i. ha^?1. The fungicides were extracted with acetone, cleaned-up using activated charcoal (trifloxystrobin) and neutral alumina (tebuconazole). Analysis was carried out by gas chromatograph (GC) and confirmed by gas chromatograph mass spectrometry (GC-MS). The recovery was above 80% and limit of quantification (LOQ) 0.05 mg kg^?1 for both fungicides. Initial residue deposits of trifloxystrobin were 0.68 and 1.01 mg kg^?1 and tebuconazole 0.673 and 1.95 mg kg^?1 from standard and double dose treatments, respectively. Dissipation of the fungicides followed first-order kinetics and the half life of degradation was 6–6.6 days. Matured onion bulb (and field soil) harvested after 30 days was free from fungicide residues. These findings suggest recommended safe pre-harvest interval (PHI) of 14 and 25 days for spring onion consumption after treatment of Nativo 75 WG at the standard and double doses, respectively. Matured onion bulbs at harvest were free from fungicide residues.