Halogenated acetaldehydes: analysis, stability and fate in drinking water

In our previous studies, chloral hydrate has been the only chlorinated acetaldehyde determined in drinking water because authentic standards of other related haloacetaldehydes were not available. Recently, standards of dichloroacetaldehyde, bromochloroacetaldehyde, dibromoacetaldehyde, bromodichloroacetaldehyde, chlorodibromoacetaldehyde, and tribromoacetaldehyde have become available commercially. They were obtained and verified for purity and stability using a dual-column GC-ECD system. Each commercial standard was found to contain small amounts of the other target haloacetaldehydes (HAs). The stability of the HAs stock solutions was solvent dependent: in acetone, the brominated species partially degraded to bromoacetone, while all target HAs were stable in MTBE for up to 8 months. The analytical parameters, required for the quantification of HAs in water, were determined and used to evaluate the stability of the HAs in water. Under the conditions of the sampling protocol (field pH adjustment to pH 4.5 and storage at 4 degrees C), the target HAs were stable in water for up to 14 days. However, at typical drinking water pH and temperature conditions, the stability varied with the HA species, pH, temperature and storage period. The trihalogenated acetaldehydes degraded, in part, to their corresponding trihalomethanes (THMs) at increasing pH and temperature. Most target HAs were detected in drinking water samples collected from various Canadian drinking water systems, and the speciation was dependent on water parameters (e.g. bromide concentration) and treatment processes. From the water samples analysed, chloral hydrate ranged between 7% and 51% of the total HAs (w/w). The weigh ratio of total HAs to total THMs (10-46%) indicated that HAs contributed significantly to the pool of DBPs in drinking water.     

Effects of bromide on the formation of THMs and HAAs

The role of bromide in the formation and speciation of disinfection by-products (DBPs) during chlorination was investigated. The molar ratio of applied chlorine to bromide is an important factor in the formation and speciation of trihalomethanes (THMs) and halogenacetic acids (HAAs). A good relationship exists between the molar fractions of THMs and the bromide incorporation factor. The halogen substitution ability of HOBr and HOCl during the formation of THMs and HAAs can be determined based on probability theory. The formation of HAAs, and their respective concentrations, can also be estimated through use of the developed model.     

Disinfection by-products in Finnish drinking waters

Disinfection by-products (DBPs) were measured in plant effluents of 35 Finnish waterworks, which utilized different treatment processes and raw water sources. DBPs were measured also from the distribution systems of three waterworks. Di- and trichloroacetic acids, and chloroform were the major DBPs found in treated water samples. The concentration of six haloacetic acids (HAA6) exceeded the concentrations of trihalomethanes (THMs). Chlorinated drinking waters (DWs) originating from surface waters contained the highest concentration of HAA6 and THMs: 108 and 26 microg/l, respectively. The lowest concentrations of DBPs were measured from ozonated and/or activated carbon filtrated and chloraminated DWs. Higher concentrations of HAA6, THMs, and adsorbable organic halogens were measured in summer compared to winter. The levels of chlorinated acetic acids, chloroform, and bromodichloromethane correlated positively with mutagenicity. Past mutagenicity levels of DWs were examined. A major reduction in the use of prechlorination, increased use of chloramine disinfection, and better removal of organic carbon were the most important reasons for the 69% decrease in mutagenicity from 1985 to 1994.     

The occurrence of disinfection by-products in the drinking water of Athens,Greece

Application of chlorination for the disinfection of drinking water results in the formation of a wide range of organic compounds, called disinfection by-products (DBPs), which occur due to the reaction of chlorine with natural organic materials. The occurrence of DBPs was studied in samples from four drinking-water treatment plants (WTPs) and from the distribution network of Athens, Greece. Twenty-four compounds, which belong to different categories of DBPs, were monitored, including trihalomethanes (THMs), haloacetic acids (HAAs), haloacetonitriles (HANs), haloketones (HAKs), chloral hydrate (CH) and chloropicrin (CP). Sampling was performed monthly for a period of two years, from three different points at each WTP and from eight points atthe distribution network. Samples were analyzed by GC-ECD methods, which included pretreatment with liquid-liquid extraction for volatile DBPs and acidic methanol esterification for HAAs. The results of the analyses have shown the presence of disinfection by-products belonging to all categories studied in all water samples collected after prechlorination. The major categories of DBPs detected were THMs and HAAs, while the other volatile DBPs occurred at lower concentrations. The concentrations of DBPs did not in any case exceed the maximum contaminant levels (MCL) set by USEPA and WHO. However, monitoring these compounds needs to be continued, because their levels could increase due to changes in the quality of water entering the water treatment plants. Reduction of the concentrations of DBPs could be achieved by optimization of the chlorination conditions, taking into account the effect of time. Moreover, research on alternative disinfection methods (e.g. ozone, chlorine dioxide, chloramines) and their by-products should be conducted to evaluate their applicability in the case of the drinking water of Greece.     

Effects of bromide and iodide ions on the formation of disinfection by-products during ozonation and subsequent chlorination of water containing biological source matters

This study aims to investigate the influence of the coexistence of halogen ions (bromide/iodide) and biological source matters on the speciation and yield of trihalomethanes (THMs), haloacetic acids (HAAs), and N-nitrosodimethylamine (NDMA) during the ozonation and subsequent chlorination of water. The results show that the concentrations of brominated THMs and iodinated THMs increased with increasing bromide and iodide concentration. These results may be attributed to the higher reactivity of hypobromous acid and hypoiodous acid generated from the ozonation and subsequent chlorination in the presence of bromide or iodide ions. The presence of bromide increased the species of brominated HAAs. There was a shift from chlorinated HAAs to brominated HAAs after increasing the concentration of bromide. The effect of iodide on HAA formation was more complex than bromide. For most samples, the concentration of total HAAs (T-HAAs) increased to the maximum and then decreased with increasing iodide concentration. The components of the organic precursors also significantly influenced the formation of brominated and iodinated disinfection by-products (Br-DBPs and I-DBPs). Humic acids produced more CHBr₃ (596.60 μg/L) than other organic materials. Microcystis aeruginosa cells produced the most tribromoacetic acid (TBAA, 84.16 μg/L). Furthermore, the yield of NDMA decreased with increasing bromide concentration, indicating that the formation of NDMA was inhibited by the high concentration of bromide.     

Water purification systems: a comparative analysis based on the occurrence of disinfection by-products

Trihalomethanes (THMs) are halogenated hydrocarbons, and are by-products of the chlorination of drinking water. Most THMs are formed in drinking water when chlorine reacts with naturally occurring organic substances such as decomposing plant and animal materials. Risks for certain types of cancer are now being correlated with the presence of disinfection by-products (DBPs). The present research uses gas chromatography to analyze the presence and levels of THMs in drinking water samples from a variety of sources. These include (1) municipal drinking water from two south Florida counties; (2) two brands of bottled water; (3) untreated residential well water; and (4) municipal tap water passed through additional water purification systems. The results are summarized in a tabular format, and the compliance of each water with existing US EPA-mandated standards is examined. General conclusions from this study are that all the waters tested complied with federal regulations regarding THM levels, properly functioning home filtration units may be quite effective in further reducing DBP concentrations and, as expected, non-chlorinated waters such as bottled water and residential well water contain lower THM levels.     

Occurrence of THMs and HAAs in experimental chlorinated waters of the Quebec City area (Canada)

Haloacetic acids (HAAs) and trihalomethanes (THMs) were generated in bench-scale chlorination experiments using treated waters (prior to final chlorination) of the three major drinking water utilities of the Quebec City area. The purpose was to investigate the formation and occurrence of these chlorination by-products (CBPs) on a seasonal basis. Data for HAAs, THMs and other physico-chemical parameters were produced through a six-month sampling program with variable conditions of water quality, water temperature, applied chlorine dose and reaction time. In waters from the three utilities, chloroform (THM specie), dichloroacetic and trichloroacetic acid (HAA species) were the most prevalent compounds due to the low concentrations of bromide in the utilities' raw waters. Significant differences in CBP occurrence were noted between the three utilities' chlorinated waters, mainly due to the type of disinfectant applied to raw water. The use of pre-ozonation, as opposed to pre-chlorination (or direct chlorination) in one of the utilities appears to be the major factor contributing to that utility's potential for compliance with current THM and future HAA standards. Seasonal variations in THMs and HAAs were mainly associated with variations in organic precursors and to changes in water temperature (two parameters which vary widely on a seasonal basis in surface waters of southern Quebec), with CBP occurrence at its highest in spring. Statistical correlations between HAAs and THMs were moderate and only temperature appeared to affect the preponderance of one CBP or the other. Finally, a regression analysis was carried out aimed at associating each CBP to water quality and the experimental parameters. Thanks to their predictive ability, multivariate models seem to be the tools with the best potential for decision-making purposes.     

Modeling and optimization of trihalomethanes formation potential of surface water (a drinking water source) using Box–Behnken design

Purpose  

The present research aims to investigate the individual and interactive effects of chlorine dose/dissolved organic carbon ratio, pH, temperature, bromide concentration, and reaction time on trihalomethanes (THMs) formation in surface water (a drinking water source) during disinfection by chlorination in a prototype laboratory-scale simulation and to develop a model for the prediction and optimization of THMs levels in chlorinated water for their effective control.     

Trihalomethane formation during water disinfection in four water supplies in the Somes river basin in Romania

Background, aim and scope  

After the discovery of chloroform in drinking water, an extensive amount of work has been dedicated to the factors influencing the formation of halogenated disinfections by-products (DBPs). The disinfection practice can vary significantly from one country to another. Whereas no disinfectant is added to many water supplies in Switzerland or no disinfectant residual is maintained in the distribution system, high disinfectant doses are applied together with high residual concentrations in the distribution system in other countries such as the USA or some southern European countries and Romania. In the present study, several treatment plants in the Somes river basin in Romania were investigated with regard to chlorine practice and DBP formation (trihalomethanes (THMs)). Laboratory kinetic studies were also performed to investigate whether there is a relationship between raw water dissolved organic matter, residual chlorine, water temperature and THM formation.     

Fate of disinfection by-products in groundwater during aquifer storage and recovery with reclaimed water

Knowledge on the behaviour of disinfection by-products (DBPs) during aquifer storage and recovery (ASR) is limited even though this can be an important consideration where recovered waters are used for potable purposes. A reclaimed water ASR trial in an anoxic aquifer in South Australia has provided some of the first quantitative information at field-scale on the fate and transport of trihalomethanes (THMs) and haloacetic acids (HAAs). The results revealed that THM half-lives varied from <1 to 65 days, with persistence of chloroform being highest and bromoform lowest. HAA attenuation was rapid (<1 day). Rates of THM attenuation were shown to be highly dependent on the geochemical environment as evidenced by the 2-5 fold reduction in half-lives at the ASR well which became methanogenic during the storage phase of the trial, as compared to an observation well situated 4 m away, which remained nitrate-reducing. These findings agree with previous laboratory-based studies which also show persistence declining with increased bromination of THMs and reducing redox conditions. Modelling suggests that the chlorinated injectant has sufficient residual chlorine and natural organic matter for substantial increases in THMs to occur within the aquifer, however this is masked in some of the field observations due to concurrent attenuation, particularly for the more rapidly attenuated brominated compounds. The model is based on data taken from water distribution systems and may not be representative for ASR since bromide and ammonia concentrations in the injected water and the possible role of organic carbon in the aquifer were not taken into consideration. During the storage phase DBP formation potentials were reduced as a result of the removal of precursor material despite an increase in the THM formation potential per unit weight of total organic carbon. This suggests that water quality improvements with respect to THMs and HAAs can be achieved through ASR in anoxic aquifers.     

Fate of disinfection by-products in groundwater during aquifer storage and recovery with reclaimed water

Knowledge on the behaviour of disinfection by-products (DBPs) during aquifer storage and recovery (ASR) is limited even though this can be an important consideration where recovered waters are used for potable purposes. A reclaimed water ASR trial in an anoxic aquifer in South Australia has provided some of the first quantitative information at field-scale on the fate and transport of trihalomethanes (THMs) and haloacetic acids (HAAs). The results revealed that THM half-lives varied from <1 to 65 days, with persistence of chloroform being highest and bromoform lowest. HAA attenuation was rapid (<1 day). Rates of THM attenuation were shown to be highly dependent on the geochemical environment as evidenced by the 2-5 fold reduction in half-lives at the ASR well which became methanogenic during the storage phase of the trial, as compared to an observation well situated 4 m away, which remained nitrate-reducing. These findings agree with previous laboratory-based studies which also show persistence declining with increased bromination of THMs and reducing redox conditions. Modelling suggests that the chlorinated injectant has sufficient residual chlorine and natural organic matter for substantial increases in THMs to occur within the aquifer, however this is masked in some of the field observations due to concurrent attenuation, particularly for the more rapidly attenuated brominated compounds. The model is based on data taken from water distribution systems and may not be representative for ASR since bromide and ammonia concentrations in the injected water and the possible role of organic carbon in the aquifer were not taken into consideration. During the storage phase DBP formation potentials were reduced as a result of the removal of precursor material despite an increase in the THM formation potential per unit weight of total organic carbon. This suggests that water quality improvements with respect to THMs and HAAs can be achieved through ASR in anoxic aquifers.     

水体中卤乙酸(HAAs)的产生、测定方法与控制途径

对饮用水中普遍存在的消毒副产物形式HAAs的产生、测定方法以及控制途径进行了阐述.并对影响HAAs生成的主要因素投氯量、溴的影响以及卤乙酸副产物(HAAFP)含量等进行了分析.生物活性炭技术是一种非常有效的控制HAAs含量和减少HAAFP含量的方法,对于保障饮用水安全性具有重要意义.     

水体中卤乙酸（HAAs）的产生、测定方法与控制途径

对饮用水中普遍存在的消毒副产物形式HAAs的产生、测定方法以及控制途径进行了阐述。并对影响HAAs生成的主要因素投氯量、溴的影响以及卤乙酸副产物（HAAFP）含量等进行了分析。生物活性炭技术是一种非常有效的控制HAAs含量和减少HAAFP含量的方法，对于保障饮用水安全性具有重要意义。     

Temporospatial variation and health risk assessment of trihalomethanes (THMs) in drinking water (northwest Iran)

Environmental Science and Pollution Research - Trihalomethanes (THMs) are one of the most common classes of disinfection by-products. In this study, the temporospatial trends and health risks due...     

Determination of bromate and chlorinated haloacetic acids in bottled drinking water with chromatographic methods

Disinfection by-products of interest such as bromate, chlorate and chlorinated haloacetic acids in 10 representative brands of bottled drinking water were investigated with ion chromatography. With the developed method, the detection limits of the disinfection by-products were in sub-microgl(-1) level. It was observed that bromate, chlorate and dichloroacetic acid could be detected in some water samples. In the bottled natural water, the concentrations for the three compounds were 0.1, 0.9 and 0.6 microgl(-1), respectively. The total concentration of disinfection by-products in the natural water sample was the highest among all the bottled drinking waters. The concentrations for the sum of disinfection by-products in the four types of bottled drinking water investigated were natural water > mineral water > spring water > purified water. The generation of disinfection by-products was much influenced by the original components and process procedure of the source water. The concentrations of bromate and chlorate in the bottled water samples hardly degraded with the increasing storage time. For dichloroacetic acid, with the prolonging of storage time, the concentration was much decreased.     

Trihalomethane formation during water disinfection in four water supplies in the Somes river basin in Romania

Background, aim and scope

After the discovery of chloroform in drinking water, an extensive amount of work has been dedicated to the factors influencing the formation of halogenated disinfections by-products (DBPs). The disinfection practice can vary significantly from one country to another. Whereas no disinfectant is added to many water supplies in Switzerland or no disinfectant residual is maintained in the distribution system, high disinfectant doses are applied together with high residual concentrations in the distribution system in other countries such as the USA or some southern European countries and Romania. In the present study, several treatment plants in the Somes river basin in Romania were investigated with regard to chlorine practice and DBP formation (trihalomethanes (THMs)). Laboratory kinetic studies were also performed to investigate whether there is a relationship between raw water dissolved organic matter, residual chlorine, water temperature and THM formation.

Materials and methods

Drinking water samples were collected from different sampling points in the water treatment plant (WTP) from Gilau and the corresponding distribution system in Cluj-Napoca and also from Beclean, Dej and Jibou WTPs. The water samples were collected once a month from July 2006 to November 2007 and stored in 40-mL vials closed with Teflon lined screw caps. Water samples were preserved at 4°C until analysis after sodium thiosulfate (Na₂S₂O₃) had been added to quench residual chlorine. All samples were analysed for THMs using headspace GC-ECD between 1 and 7 days after sampling. The sample (10 mL) was filled into 20-mL headspace vials and closed with a Teflon-lined screw cap. Thereafter, the samples were equilibrated in an oven at 60°C for 45 min. The headspace (1 mL) was then injected into the GC (Cyanopropylphenyl Polysiloxane column, 30 m × 53 mm, 3 μm film thickness, Thermo Finnigan, USA). The MDLs for THMs were determined from the standard deviation of eight standards at 1 μg/L. The MDLs for CHCl₃, CHBrCl₂, CHBr₂Cl and CHBr₃ were 0.3, 0.2, 0.3 and 0.6 μg/L, respectively. All kinetic laboratory studies were carried out only with water from the WTP Gilau. The experiments were conducted under two conditions: baseline conditions (pH 7, 21°C, 2.5 mg/L Cl₂) to gain information about the change of the organic matter in the raw water and seasonally variable conditions to simulate the actual process at the treatment plant and the distribution system.

Results and discussion

This study shows that the current chlorination practice in the investigated plants complies with the THM drinking water standards of the EU. The THM concentrations in all samples taken in the four treatment plants and distributions systems were below the EU drinking water standard for TTHMs of 100 μg/L. Due to the low bromide levels in the raw waters, the main THM formed in the investigated plants is chloroform. It could also be seen that the THM levels were typically lower in water supplies with groundwater as their water resource. In one plant (Dej) with a pre-ozonation step, a significantly lower (50%) THM formation during post-chlorination was observed. Laboratory chlorination experiments revealed a good correlation between chloroform formation and the consumed chlorine dose. Also, these experiments allowed a semi-quantative prediction of the chloroform formation in the distribution system of Cluj-Napoca.

Conclusions

CHCl₃ was the most important trihalomethane species observed after the chlorination of water in all of the sampled months. However, TTHM concentrations did not exceed the maximum permissible value of 100 μg/L (EU). The THM formation rates in the distribution system of Cluj-Napoca have a high seasonal variability. Kinetic laboratory experiments could be used to predict chloroform formation in the Cluj-Napoca distribution system. Furthermore, an empirical model allowed an estimation of the chloroform formation in the Gilau water treatment plant.

     

Occurrence and formation of trihalomethanes in marine aquaria studied using solid-phase microextraction gas chromatography-mass spectrometry

The occurrence and formation of chlorinated and brominated trihalomethanes (THMs) were studied in artificial saltwater and natural seawater marine aquaria as well as in groundwater and surface waters. A new headspace solid-phase microextraction method was used, which included gas chromatography-mass spectrometry and provided method detection limits of less than 0.1 microg/L, with a signal-to-noise ratio of 3 to 5. The results showed that disinfection by using either chlorine or ozone caused a significant formation of THMs in situ. Speciation of the THMs was a strong function of the water matrix, with initial bromide concentrations playing a pivotal role. These results provide a tool for understanding and monitoring the formation of key disinfection byproducts in marine aquaria that may cause respiratory, eye irritation, or other health concerns.     

离子色谱在饮用水消毒副产物及高氯酸盐分析中的应用

介绍了离子色谱在饮用水中消毒副产物及高氯酸盐分析中的应用。重点介绍了离子色谱测定饮用水中溴酸盐和高氯酸盐的方法。简单介绍了卤代乙酸和氯酸盐的离子色谱测定法及离子色谱-质谱联用技术在饮用水消毒副产物及高氯酸盐分析中的应用。     

Formation of nitrogenous disinfection by-products from pre-chloramination

A sampling survey investigated the formation of nitrogenous disinfection by-products (N-DBPs) and carbonaceous DBPs (C-DBPs) from pre-chloramination, an increasingly common treatment strategy in China for regulated C-DBP control, followed by subsequent conventional water treatment processes, i.e., coagulation, sedimentation, and filtration. Dihalogenated N-DBPs typically peaked in the summer and early autumn with a relatively higher temperature, with the maximum levels of dichloroacetamide (DCAcAm), dichloroacetonitrile (DCAN), bromochloroacetonitrile, dibromoacetonitrile and dichloroacetone at 1.8, 6.3, 6.0, 2.6 and 1.8 μg L⁻¹ in the finished water, respectively. Also, the levels of all the dichlorinated N-DBPs were correlated with the ratio of dissolved organic nitrogen (DON) to dissolved organic carbon, implying autochthonous DON played an essential role in the formation of these DBPs. In contrast, the yields of trihalogenated DBPs [chloroform (CF), trichloronitromethane (TCNM) and trichloroacetone (TCAce)] appeared not to be significantly affected by seasons. CF and DCAN were the dominant species in trihalomethanes (THMs) and dihaloacetonitriles (DHANs), respectively. Bromine was more readily incorporated into DHANs to form brominated DBPs than THMs during pre-chloramination. Although pre-chloramination can ensure the finished water to meet with the current Chinese THM regulatory limits, the increased levels of TCNM and TCAce may be a new water quality concern.     

Minimization of the formation of disinfection by-products

The drinking water industry is required to minimize DBPs levels while ensuring adequate disinfection. In this study, efficient and appropriate treatment scheme for the reduction of disinfection by-product (DBPs) formation in drinking water containing natural organic matter has been established. This was carried out by the investigation of different treatment schemes consisting of enhanced coagulation, sedimentation, disinfection by using chlorine dioxide/ozone, filtration by sand filter, or granular activated carbon (GAC). Bench scale treatment schemes were applied on actual samples from different selected sites to identify the best conditions for the treatment of water. Samples were collected from effluent of each step in the treatment train in order to analyze pH, UV absorbance at 254 nm (UVA₂₅₄), specific UV absorbance at 254 nm (SUVA₂₅₄), dissolved organic carbon (DOC), haloacetic acids (HAAs) and trihalomethanes (THMs). The obtained results indicated that using pre-ozonation/enhanced coagulation/activated carbon filtration treatment train appears to be the most effective method for reducing DBPs precursors in drinking water treatment.