Feasibility of a monitoring system for detecting changes in dioxin concentrations of both in flue gas and fly ash in incineration plants

Surrogate measurements should be low in cost and quick to perform. To examine its feasibility, continuous surrogate monitoring was performed using an organic halogen compound (OHC) analyzer. Surrogates for dioxins (DXNs) from waste incinerators were examined by changing the operating conditions such as the atomized volume of activated carbon added and the temperature at the inlet of the dust collector. OHCs were measured along with DXNs in flue gas at the inlet and the outlet of the dust collector of two waste incinerators over five runs; the fly ash was sampled at the same time. Although the final flue gas concentration of DXNs at the incineration plants was below the regulation criteria, this does not mean complete reduction of DXNs. In addition, the de novo synthesis of DXNs inside the dust collectors was studied by analyzing the mass balance for DXNs concentrations in flue gas and fly ash. Semivolatile chlorinated organic compound concentrations at the outlet of the bag filter were basically well correlated with DXNs levels at the inlet of the bag filter in the test runs. When advanced flue gas treatment is applied by using a bag filter and lime/activated carbon adsorbent, DXNs that may be generated during flue gas cooling processes move to the fly ash, and this amount determines the mass balance of the entire system. It may be useful to monitor surrogate organic halogens for detecting changes in DXN concentrations of both flue gas and fly ash in incineration plants.     

中国2030年能源发展预测与对策研究

在回顾2000年-2010年中国能源消费的基础上,对中国2030年能源发展及耗煤量进行了预测,预测结果表明,2030年中国能耗总量将控制在55～60亿t标煤,耗煤量控制在40～45亿t标煤。建议中国2011年-2015年、2015年-2020年、2020年-2025年和2025年-2030年能源弹性系数分别为0.5、0.5、0.4和0.3。开展煤炭休养生息战略,多进口煤炭。     

Three-Dimensional Numerical Simulation of Air Pollutant Dispersion in Street Canyons

The PHOENICS Computational Fluid Dynamics (CFD) software package has been used with a standard k- turbulence model to simulate the three-dimensional dispersion of air pollutants in an urban street canyon. In all cases, a vortex was formed within the street canyon, characterized by updrafts near the upwind buildings and down-drafts near the downwind buildings. Contours of pollutant concentrations over a transverse vertical plane at mid-canyon show pollutants circulating within the vortex, with higher concentrations at the leeward face than at the windward faces, and higher concentrations above downwind buildings than above upwind buildings. Longitudinal distributions of pollutant concentrations at leeward and windward faces are characterized by higher concentrations at mid-block and lower concentrations at the ends. These results agree qualitatively with previous wind tunnel findings such as those of Hoydysh and Dabberdt (1988) and Wedding et al. (1977). The results also suggest that the k- turbulence model is satisfactory for simulating the effect of turbulence on dispersion of pollutants in street canyons     

厦门市家具类大件垃圾处理的经验及启示

调研厦门市家具类大件垃圾处理现状,总结厦门市处理家具类大件垃圾的主要经验。根据厦门市家具类大件垃圾处理的实践,提出适合我国国情的家具类大件垃圾处理框架体系,以期为国内其他城市开展家具类大件垃圾处理工作提供借鉴。家具类大件垃圾处理应遵循3个原则,即前端坚持可持续发展的原则,中端坚持循环利用的原则,终端坚持零遗弃的原则。     

Soil Respiration in Relation to Small-Scale Patterns of Lead and Mercury in Mor Layers of Southern Swedish Forest Sites

Pollution-related lead (Pb) andmercury (Hg) in mor layers of Southern Swedenmight have effects on soil biology, although inthe literature effect concentrations have beenidentified at much higher levels. Considerablesmall-scale spatial variability in heavy metalcontents and microbial respiration in mor layersof forest sites was used to calculatecorrelations that could reveal toxic effects.Negative correlations were always strongest atsites with high loads of Pb or Hg, which was considered to indicate metal toxicity. The highload sites were found in Southwestern Sweden,locally at a motorway and at a chlorine-alkalifactory. Other factors of possible influence,such as other pollutants, age of organic materialor climatic differences, would affect high andlow load sites alike. Negative correlations withrespiration were found for Pb at sites with 74 g g^-1 of mean Pb content in O_f-layer and for Hg at 0.25 g g^-1.     

A study of the dental solid waste produced in a school of dentistry in Turkey

Dental wastes are regulated under medical waste control regulations in most countries. Even though the quantity of hazardous wastes in dental solid wastes is a small proportion, there is still cross infection risk and potential danger for environment associated with mismanaged wastes. For this reason, knowledge of waste composition and development of proper management alternatives are necessary. In this study, the composition of solid wastes coming from eight clinics of the dental school of a University hospital in Turkey is examined. Although the waste has some variations between the two samplings, the general picture is such that the major components remain pretty much the same (in terms of %) for a fixed clinic. The composition of waste changes from one clinic to the other as expected. However, one can deduce from the data obtained that at about 35%, rubber gloves constitute close to the half of the total solid waste in almost all the clinics. Other major component is paper forming approximately 30% of the solid waste. In general, total waste coming from the clinics is related with the number of procedures conducted on patients at the clinics. Only a small fraction of the waste is hazardous indicating that at Hacettepe University School of Dentistry, hazardous waste collection rules are obeyed in most of the times.     

钒钛SCR脱硝催化剂低温研究进展

由于商用钒钛SCR催化剂存在活性温度偏高等缺点,开发低温高活性的催化剂体系已成为国内外研究的热点。分析了钒钛催化剂低温SCR反应的脱硝机理,探讨了催化剂性能的低温改性方法和努力方向,介绍了催化剂中毒方面的研究进展,为催化剂的完善和低温SCR的深入研究提供参考。     

Identification of PM10 Sources in a Mediterranean Island

Due to the dry Mediterranean climate in Cyprus, particulate matter is resuspended from soils and other surfaces. From November 2002 to August 2003, gravimetric PM₁₀ measurements were carried out at three characteristic sites (traffic, residential and rural). A significant seasonal trend with high winter concentrations was observed at the traffic site. Special events, e.g. long-range transport of Sahara dust storms, were recorded over traffic, residential and rural areas in the order of six to eight events per year, with a major frequency in summer and spring periods. This contributes to the increase of 24-h EU limit value exceedances for PM₁₀ at the three investigated sites. The origin of the PM₁₀ load was determined by enrichment factors based on analyses of the local soil deposition at the investigated sites. Furthermore, positive matrix factorisation modelling was applied to find the sources of PM₁₀. Results indicate that the major emission sources affecting the PM₁₀ load were mineral soil, sea salt, road dust, oil combustion, secondary pollutants and gasoline vehicles. The natural contribution (local mineral soil and sea salt) at the three sites was in the range of 7–9 μg m^?3 in PM₁₀. Besides the Sahara dust storms and natural background concentrations, the vehicular pollution was found as the largest contributor (12–14 μg m^?3) to PM₁₀ load at the traffic site.     

垃圾焚烧中抑制二恶英二次生成的方法探讨

根据生活垃圾焚烧技术中二恶英的生成机理，余热锅炉的烟气在低温区急冷可以避免二恶英在低温区的再次合成，但目前在余热锅炉烟气低温区急冷是不可行的。提出一种从垃圾焚烧系统设计上进行烟气的急冷，从而抑制二恶英低温区二次生成的新方法。     

Use of Performance Models in Restoration Projects

Environmental restoration projects can benefit from using performance models tied to monitoring plans and closure/exit strategies. Theoretical aspects are discussed and a case study is provided to illustrate how models can be developed and applied. Recognizing that site characterization cannot remove all uncertainty, most performance models cannot be narrowly developed (e.g., specific concentrations expected over time). Instead they must define threshold values at which performance data indicate the remedy is failing, or at least is not operating at the required level to achieve objectives within a reasonable timeframe. Ultimately, the performance model should be transformed to a closure model. The closure model is intended to document how closure was achieved and what measures remain in place to ensure protection of human health and the environment. In this context, the performance model is an intermediate step in the sequence starting from a conceptual site model and ending as the closure model. © 2014 Wiley Periodicals, Inc.     

The role of cost in remedy selection

Records of Decision from 16 environmental cleanup sites on 11 different Air Force bases were evaluated to determine if cost plays a role in remedy selection. Cost percentile (the cost of the selected remedy compared to the ranges of costs in the alternatives considered) was evaluated against the variables of risk (current and future, carcinogenic and noncarcinogenic), location, and contaminated media at the sites. Despite a statutory preference for permanent (and usually more expensive) remedies, the study found that cost is a significant factor in remedy selection. Eighty percent of the selected remedies fell in the bottom two thirds of alternatives by cost. Current carcinogenic risk and cost percentile were moderately correlated, but no significant correlation was found between the percentile of the selected remedy and future risk at the site or the location of the site. There was a moderate correlation between the contaminated medium and the percentile. Decision makers at sites with contaminated groundwater were more likely to select a high-cost alternative than sites with other contaminated media.     

Medical wastes characterisation in healthcare institutions in Mauritius

This study was initiated to characterize solid and liquid wastes generated in healthcare institutions and to provide a framework for the safe management of these wastes. The project was carried at three major medical institutions, namely, the Jeetoo Hospital, the Sir Seewoosagur Ramgoolam National (SSRN) Hospital and the Clinic Mauricienne. A waste audit carried out at these sites revealed that approximately 10% of solid wastes was hazardous in nature, consisting mainly of infectious, pathological and chemical wastes. The average amount of hazardous wastes per patient per day was found to be 0.072 kg at Jeetoo hospital, 0.091 kg at SSRN hospital and 0.179 kg at the clinic. The amount of hazardous wastes generated as a function of the number of occupied beds was found to follow a relationship of type y=0.0006x-0.19, where y was the amount of hazardous wastes generated per bed per day and x was the number of occupied beds. The waste quantifying process also revealed that at SSRN Hospital, 0.654 m(3) of water was being consumed per patient per day and the amount of wastewater produced was 500 m(3)/day. Further analysis revealed that the wastewater was polluting with chemical oxygen demand (COD), biological oxygen demand (BOD(5)), total suspended solids (TSS) and coliform content well above permissible limits.     

Oil uptake and depuration in oysters after use of dispersants in shallow water in El Salvador

Dispersants were used in shallow water (4–6 m) and in the surf zone at a small spill (400 bbls) of Venezuelan Recon at the port of Acajutla, El Salvador in June 1994. Subtidal oysters were collected 1 and 4 weeks post-spill to determine the degree of exposure of benthic resources to the dispersed oil. Two samples of oysters from the area of dispersed oil contained total PAHs of 147 and 164 ppm, dry weight, compared with background levels less than 1.0 ppm. Four weeks post-spill, PAH levels decreased by 94–98%. Half-lives for individual PAH compounds were estimated and were generally consistent with results from laboratory experiments. Monitoring of bivalves during dispersant applications can document the areal and vertical extent of dispersed oil in the water column.     

好氧生物流化床反应器处理有机废水技术进展

介绍了国内外好氧生物流化床反应器处理有机废水技术的发概况,分析了好氧生物流化床反应技术的发展动向,并介绍了几种新型的好氧生物流化床反应器。     

Clogging of finger drain systems in MSW landfills

A numerical model ‘BioClog’ is used to examine clogging of granular drainage material within finger drains at the base of landfills. The reduction in porosity of drainage material is evaluated as the accumulation of clog mass reduces the pore spaces of granular media. The leachate mounding within the landfills caused by the reduction in hydraulic conductivity of finger drain is modeled. The effect of overburden pressure on the engineering properties of waste material and consequent leachate mounding is considered. The calculated rates of leachate mound development for two landfills with finger drain leachate collection are shown to be in encouraging agreement with the observed data at the times when data were available. It is demonstrated that a significant leachate mound can be expected to develop over time when the leachate collection system is comprised of finger drains; however the rate of increase and the magnitude at a given time will depend on a number of factors including the grainsize, thickness and spacing of the finger drains, and the thickness of waste as well as the leachate generation rate.     

Leachability of municipal solid waste ashes in simulated landfill conditions

In Japan the volume of municipal solid waste is reduced by incineration, with fly ash and bottom ash disposed in controlled landfills. The leachability of anions and heavy metal cations, Zn, Cu and Pb, from MSW fly ash and bottom ash at different pHs was examined using batch- and column-leaching tests. The MSW ashes had a high capacity for neutralizing acids. Behaviour during leaching depended on the pH of the solution. For the volumes applied, the leachabilities of MSW fly ash were very similar at pHs from 3 to 6. Due to its amphoteric nature, Pb is leachable at pHs of approximately 10 or more, with leachate concentrations of about 3 and 3-10mg/L for the fly ash and bottom ash, respectively, much higher than for Zn and Cu. Pb concentrations for most leaching solutions were 1 and 3mg/L for the fly ash and bottom ash, respectively. Zn, and Cu leached at low concentrations for solutions of pH 3-6. Na and K ions leached at high concentrations of approximately 5000 mg/L in the first batch leaching test, decreasing to 10mg/L by the fourth leach. Ca and Mg ions leached more gradually than Na and K. Cl(-) and SO(4)(2+) ions were the major anions in the MSW ash. The high pH and cation leaching are expected to have negative impacts on the performance of clay liners.     

五莲县石材废料的资源化利用

石材工业是资源加工型产业,加工过程会产生大量的石材废料.我国对石材加工废料的研究起步较晚,应用技术不成熟.介绍了目前国内外对石材废料的几种主要资源化利用方式,并结合五莲县石材产业基地石材加工实际工艺及废料资源化处理方式,研究石材废料的资源化利用.     

Performance of conventional remedial technology for treatment of MTBE and benzene at UST sites in Kansas

Groundwater at most underground storage tank (UST) spills sites in Kansas contains both methyl tertiary butyl ethylene (MTBE) and benzene, and both contaminants must be effectively treated to close the sites. Soil vacuum extraction, air sparging, and excavation are the most common treatment technologies in Kansas. To compare the relative performance of these conventional remedial technologies for treating MTBE as compared to benzene, 66 sites in the Kansas UST Trust Fund were identified that had initial concentrations of both MTBE and benzene above the reporting limit of 1 μg/L, and that had at least two rounds of analytical data. Sites were excluded from the comparison if the monitoring wells had free product. Of the 66 sites, 15 had met the clean‐up goal for benzene, and 50 had met the goal for MTBE. The extent of treatment for MTBE and benzene was calculated as the ratio of the highest concentration in any well at the site in the most recent round of sampling to the maximum concentration in any well at the site in the previous rounds of sampling. The extent of treatment was greater for MTBE (statistically significant at p = 0.032). The geometric mean of the extent of treatment in the 66 sites was 0.057 for MTBE, compared to 0.14 for benzene. In Kansas, conventional technologies removed MTBE from the source areas of groundwater plumes at least as effectively as they removed benzene. © 2003 Wiley Periodicals, Inc.     

Aerobic Biodegradation of Polymers in Solid-State Conditions: A Review of Environmental and Physicochemical Parameter Settings in Laboratory Simulations

During the last few years, biodegradable polymers have been developed to replace petrochemical polymers. Until now, research devoted to these polymers essentially focused on their biodegradability. There is now a need to bear out their nontoxicity. To verify this, the biodegradation must be carried out in accelerated laboratory tests which allow the metabolites and residues to be recovered. To reproduce the natural conditions (compost, field) as closely as possible, degradation experiments must be run on solid-state substrates. We review studies of aerobic degradation in solid-state substrates. This article focuses in particular on the environmental, physical, and chemical parameters (such as substrate nature, moisture, temperature, C/N ratio, and pH) that influence biodegradation kinetics. This study also aims at finding the solid substrate most adapted to residues and metabolite recovery. The most significant parameters would appear to be the substrate type, moisture content, and temperature. Inert substrates such as vermiculite are well suited to residue extraction. This review also opens the field to new research aimed at optimizing conditions for aerobic solid-state biodegradation and at recovering the metabolites and residues of this degradation process.     

Treatment of remediation wastes in RCRA corrective action management units

This article explains new EPA regulations that provide for use of corrective action management units (CAMUs) and temporary units (TUs) as cost-effective techniques for remediating hazardous wastes at facilities undergoing RCRA corrective action and at CERCLA remediation sites. The author outlines EPA criteria for approving the use of CAMUs, discusses the benefits and limitations of using them, and recommends possible ways to improve on the CAMU concept.