重金属元素在樟树人工林中的累积与迁移

结合樟树人工林生态系统生物产量研究,采用Hp3510原子吸收分光光度法测定樟树人工林生态系统不同组分中Cu、Zn、Mn、Pd、Ni、Cd的含量,探讨了重金属元素Cu、Zn、Mn、Pb、Ni、Cd在湖南株洲市樟树人工林中的累积与迁移.结果表明,樟树人工林地土壤层(0～100 cm)中,6种重金属元素的平均含量以Pb为最高,为67.929 mg/kg,Cd最低,仅为0.699 mg/kg,排序为Pb＞Zn＞Mn＞Ni＞Cu＞Cd,总储量为2 737 174 kg/hm2.在樟树不同器官中,Cu、Zn、Mn、Pd、Ni、Cd的含量范围分别为6.849～13.178 mg/kg,3.776～37.443 mg/kg,32.214～659.130 mg/kg,1.626～15.544 mg/kg,0.218～3.719 mg/kg,1.033～9.506 mg/kg.樟树对土壤中6种重金属元素富集能力排序为Cd＞Mn＞Zn＞Cu＞Pb＞Ni.在樟树林中,6种重金属元素的总积累量为11.124 kg/hm2,且排序为Mn(8.097 kg/hm2)＞Zn(1.429 kg/hm2)＞Cu(0.763 kg/hm2)＞Pb(0.491 kg/hm2)＞ Cd(0.272 kg/hm2)＞Ni(0.072 kg/hm2),重金属元素积累量空间分布为叶(3.447 kg/hm2)＞枝(2.863 kg/hm2)＞皮(1.685 kg/hm2)＞干(1.635 kg/hm2)＞根(1.307 kg/hm2).樟树林与环境之间,Mn的交换能力最强,其次是Cd、Zn、Cu,再次为Ni、Pb.     

金属离子及盐分对苯胺好氧生物降解过程的影响

以苯胺废水处理反应器内污泥为菌源,采用间歇反应的方法考察了Fe3 、Ni2 、Zn2 、Cr(Ⅵ)和Cu2 5种金属离子及盐分对苯胺好氧降解过程的影响.结果表明,适宜浓度的Fe3 、Ni2 、Zn2 、Cr(Ⅵ)和Cu2 可以促进苯胺的降解,苯胺降解速率提高了5.7%～26.6%.但当Fe3 、Ni2 、Zn2 、Cr(Ⅵ)和Cu2 的质量浓度分别大于50 mg/L、5 mg/L、2.5 mg/L、2.5 mg/L和1 mg/L时,开始对苯胺降解菌产生抑制作用.按毒性从大到小的顺序排列为: Cu2 、Cr(Ⅵ)、Zn2 、Ni2 、Fe3 .苯胺降解菌生长最佳盐度(NaCl质量分数)介于0.5%～1.0%.研究表明,在苯胺废水处理实践中应把金属离子和盐度控制在适宜的范围内.     

橡胶促进剂M盐废水生物处理技术研究

为探讨微生物技术在橡胶促进剂M盐废水处理中的应用,利用高效优势菌强化A2O工艺对橡胶促进剂M盐废水进行处理,整个系统运行过程分为污泥的培养与驯化阶段及稳定运行阶段.在稳定运行阶段CODCr平均去除率达90.71%,氨氮平均去除率达78.31%.以Mn2 、Fe2 、Mg2 、Ni2 为4个影响因子,通过正交实验分析无机离子对橡胶促进剂M盐废水中有机物降解的促进作用.由实验数据的极差大小可知,各无机离子对优势复合菌降解橡胶有机废水的影响从大到小依次为: Mn2 、 Fe2 、Ni2 和Mg2 . 4种离子最佳质量浓度组合为: 0.500 mg/L 的Mn2 、1.00 mg/L 的Fe2 、35.0 mg/L的Mg2 和0.025 mg/L的Ni2 .     

生物质炭对电解锰废渣中Mn、Cd、Zn的淋溶效应

通过静态浸出和动态淋溶实验,探讨生物质炭对电解锰废渣中Mn、Cd、Zn的淋溶效应.结果表明：电解锰废渣浸出液中Mn、Cd、Zn的平均含量分别为73.71 mg/L、5.87 mg/L、0.270 mg/L;淋溶液中Mn、Cd、Zn的平均含量为256.80 mg/L、0.045 1 mg/L、0.33 mg/L,其中Mn、Cd均超过地表水Ⅲ类质量标准.电解锰废渣添加2％ ～4％生物质炭后,淋溶液中Mn、Cd、Zn平均含量分别减少了0.97％ ～ 37.4％、3.80％ ～ 53.7％、8.7％ ～ 56.5％,当生物质炭添加量为6％时,Mn、Cd、Zn平均含量减少程度分别处在2.59％～37.4％、15.7％～ 53.7％、25％ ～ 56.5％,说明生物质炭能明显抑制电解锰废渣的重金属向水体的迁移.     

芜湖市区地表灰尘中重金属空间分布特征及来源分析

为初步探讨芜湖市区地表灰尘重金属空间分布特征及主要来源,于2008年4月采集了芜湖市高新技术开发区、中心城区、经济技术开发区地表灰尘样品,用电感耦合等离子体发射光谱仪(ICP-OES)测定了9种重金属质量比.结果表明,Zn、Cd、Pb、Co、Ni、Mn、Cr、V和Cu的质量比分别为313.53 mg/kg、1.95 mg/kg、138.61 mg/kg、8.19 mg/kg、21.38 mg/kg、589.87 mg/kg、110.31 mg/kg、55.19 mg/kg和135.42 mg/kg.主要污染元素依次为Cd、Pb、Cu、Zn,其质量比超出背景值4倍以上.重金属总体上由南向北呈逐渐增加的趋势.Co、Cu、Cr和Ni具有相似的分布规律,最高值均出现在经济技术开发区;V和Mn主要富集在研究区东南角和东北角,往西逐渐下降;Zn和Pb的最高值出现在中心城区和研究区的最东北角;Cd则出现多个高污染中心,且整个研究区质量比较高,污染较为严重.空间分布及统计分析表明,芜湖市区地表灰尘中重金属主要有两个来源:1)工业排放,特征元素为Co、Ni、Cu、V、Mn;2)城市交通活动,特征元素为Zn、Cd、Cr、Pb.     

多壁碳纳米管短期作用对活性污泥系统脱氮除磷效果的影响

研究了不同质量浓度(1 mg/L和20 mg/h)多壁碳纳米管(Muhiwalled Carbon Nanotubes,MWCNTs)短期(21 d)作用对序批式活性污泥反应器(SBR)废水脱氮除磷效果的影响.结果表明,1mg/L和20mg/L MWCNTs废水的持续作用对反应器出水NH4+-N、NO3--N、NO2--N和TP质量浓度(分别为0.35 mg/L、4.5 mg/L、0.1 mg/L和0.15 mg/L)及1个反应周期内的氮磷转化过程并未产生明显的影响.活性污泥3h呼吸抑制试验表明,低质量浓度(ρ＜100 mg/L)MWCNTs短暂作用(3h)对活性污泥活性并没有明显的抑制作用.但当MWC-NTs质量浓度达到g/L级别后,MWCNTs对活性污泥活性存在明显的抑制作用,而且MWCNTs对活性污泥的呼吸抑制作用与质量浓度呈正相关性.研究表明,1 mg/k和20 mg/L MWCNTs对活性污泥系统短期作用并不影响活性污泥系统脱氮除磷的效果.     

生物法净化烹饪油烟营养配比的优化

在pH值=7、温度35℃下,采用正交实验方法对影响活性污泥微生物净化烹饪油烟的营养元素与溶解氧进行了优化,即:补加淀粉溶液20 m L、硝酸铵6 m L、磷酸二氢钾1 m L、微量元素(质量浓度分别为0. 03,0. 1,0. 043 g/L的Cu SO_4·5H_2O,Zn SO_4·7H_2O,MnSO_4·H_2O) 2 m L和控制溶解氧质量浓度7. 1 mg/L,各因素对降解率影响大小关系为溶解氧硝酸铵磷酸二氢钾补加淀粉微量元素。将最优综合培养条件应用于模拟油烟净化组合装置。结果表明,活性污泥微生物对油烟污染物有很好的降解能力,在前24 h的降解率和降解速率最大,分别为46. 1%和0. 54 mg/(L·h)。     

酵母融合菌-活性污泥曝气处理含镍废水研究

利用酵母融合菌RJ与活性污泥曝气处理含镍废水.实验结果表明,融合菌对废水中的镍具有很强的富集性能,投加10g/L菌体,处理20 mg/L含镍废水,去除率可达70.10%;同时投加6g/L活性污泥,去除率上升到80.73%,出水固液分离效果得到改善;且融合菌的pH值适用范围较广,当pH=3～9时,去除率均在75%以上;溶解氧是影响曝气生物吸附的重要因素,在缺氧或富氧环境下,生物吸附会受到抑制,DO为2.5～4.5 mg/L时吸附效果较好;融合菌-活性污泥曝气处理不同浓度Ni2 的吸附等温线符合Freundlich模型,相关系数为0.997 5.     

铂载钴钼二元硫化物对H_2S电催化活性研究

为考察溶胶凝胶法制备的Co-Mo二元硫化物对H_2S气体的电催化活性,通过循环伏安法和Tafel曲线分析对铂载不同Co、Mo掺杂比的电催化剂进行表征.结果表明,不同阳极电催化剂交换电流密度J_0由大到小依次为,铂载n(Co):n(Mo)=2:3、铂载n(Co):n(Mo)=2:1、铂载n(Co):n(Mo)=1:1和铂,即铂载n(Co):n(Mo)=2:3阳极电催化剂具有较好的活性,这与循环伏安曲线测试结果一致.电解质溶液pH值为6～7时,随着温度的升高铂载n(co):n(Mo)=2:3阳极电催化剂活性呈现上升的趋势.优化后的Co、Mo掺杂原子比约为0.66,此类电催化剂在操作温度80℃下,交换电流密度为1.318mA/cm~2,表观活化焙值为616.6 kJ/mol .研究表明,铂载钴钼二元硫化物适合作为低温H_2S燃料电池阳极电催化剂,其中Co、Mo掺杂比对电催化活性影响较大.     

重金属吸附菌处理含锌废水的研究

从污水厂活性污泥中分离筛选出3株对重金属锌吸附能力较强的菌株,考察了pH值、温度和Zn2+质量浓度对菌株吸附含锌废水的影响。结果表明,菌株Z-5-2在pH=7.0、温度30℃、Zn2+质量浓度为200mg/L时吸附效果最好;菌株Z-5-3在pH=6.0、温度28℃、Zn2+质量浓度为250mg/L时吸附效果最好;菌株Z-5-4在pH=7.0、温度28℃、Zn2+质量浓度300mg/L时吸附效果最好。其中,菌株Z-5-4吸附能力最强,吸附率可达95.5%,对菌株Z-5-4进行16SrDNA序列分析,鉴定Z-5-4为产吲哚金黄色杆菌。     

油浸变压器排油注氮装置在500kV变电站的设计与应用

在分析500kV变电站主变压器消防系统的现状,比较3类消防系统优缺点的基础上,详细论述了主变排油注氮装置的结构组成、工作原理、参数计算、控制系统设计以及需要注意的事项等,为下一步排油注氮装置的推广应用打下基础.     

HAZOP结合What-if方法在某延迟焦化装置除焦中的应用

为克服传统危险与可操作性（HAZOP）定性分析方法在复杂操作、间歇作业等过程中使用的局限性,提出在传统HAZOP定性分析方法的基础上结合What-if（故障假设）方法,对人的不安全行为和操作规程不完备所导致的风险后果分析作出补充。详细说明其技术原理、工作流程等使用细节,系统阐述该方法与传统HAZOP定性分析方法的区别,并在某延迟焦化装置的除焦操作的风险分析中应用。经分析,识别出在“给水-泡焦”节点,有“操作规程错误”场景2项,“操作规程不具体”场景1项,不存在“操作人员未按操作规程执行”场景。研究结果表明:本文方法有效且具有较好效果,可以广泛应用于操作规程/作业指导书审查、作业过程隐患排查等方面,帮助企业开展操作层面的风险识别与管理,提升企业的生产安全水平。     

Nighttime pedestrian fatalities: A comprehensive examination of infrastructure,user, vehicle,and situational factors

Introduction: Pedestrian fatalities in the United States increased 45.5% between 2009 and 2017. More than 85% of those additional pedestrian fatalities occurred at night. Method: We examine Fatality Analysis Reporting System (FARS) data for fatal pedestrian crashes that occurred in the dark between 2002 and 2017. Within-variable and before/after examinations of crashes in terms of infrastructure, user, vehicle, and situational characteristics are performed with one-way analysis of variance (ANOVA) and two-sample t-tests. We model changes in crash characteristic proportions between 2002–2009 and 2010–2017 using linear regressions and test for autocorrelation with Breusch-Godfrey tests. Results: The increase in fatal nighttime pedestrian crashes is most strongly correlated with infrastructure factors: non-intersection unmarked locations (saw 80.8% of additional fatalities); 40–45 mph roads (54.6%); five-lane roads (40.7%); urban (99.7%); and arterials (81.1%). In addition, SUVs were involved in 39.7% of additional fatalities, overrepresenting their share of the fleet. Increased pedestrian alcohol and drug involvement warrant further investigation. The age of pedestrians killed increased more (18.1%) than the national average (3.2%). Conclusions: By identifying factors related to the increase in nighttime pedestrian fatalities, this work constitutes a vital first step in making our streets safer for pedestrians. Practical Applications: More research is needed to understand the efficacy of different solutions, but this paper provides guidance for such future research. Engineering solutions such as road diets or traffic calming may be used to improve identified infrastructure issues by reducing vehicle speeds and road widths. Rethinking vehicle design, especially high front profiles, may improve vehicle issues. However, the problems giving rise to these pedestrian fatalities are likely a result of not only engineering issues but also interrelated social and political factors. Solutions may be correspondingly comprehensive, employing non-linear, systems-based approaches such as Safe Systems.     

森林地表火蔓延模拟方法及其计算机实现

进行了森林火蔓延的研究,对传统的经验公式和模型进行改进,明显发现改进的模型有更好的结果,用计算机巧妙准确地实现了模拟模型,在风力不是特别大,地形变化不是特别剧烈时,该模型有较高精度;并结合火蔓延的主要因素（气象因子、气候、地形等）,进行系统分析,写出算地,编制实现地表火蔓延的预测预报计算机系统软件。这对于有效的组织扑救、减少火灾损失、计算森林火灾的损失评估有重要意义。     

潞安矿区煤层渗透率的各向异性特征实验研究

为了研究原位煤体渗透性的各向异性特征,以山西潞安常村矿3号煤层圆柱试样为对象,利用TCQT-Ⅲ型低渗煤层气相驱替增产试验装置,对煤样进行加载,并以氮气注入压力2.0 MPa的条件下,分析垂直层理和平行层理2个方向的煤体变形和渗透率变化特征。实验结果表明:煤样在加载过程中,平行和垂直层理煤样渗透率均随着有效应力的增大而减小,平行层理方向的渗透率始终大于垂直层理方向,应力加载初期渗透率急剧下降,最后逐渐趋于平缓;径向应变的增加量与渗透率呈正相关性,且平行层理相关性大于垂直层理;沿平行层理方向的裂隙度大于沿垂直层理方向,沿垂直层理方向的应变量大于沿平行层理方向;应变增加量均随有效应力的增加而逐渐减小。研究结果可为煤层井网布置及优化提供参考。     

Footedness and Mounting—Short Review and Two Case Studies

Footedness is a personal quality like handedness. Footedness may be associated with moving ability during mounting, dismounting, and jumping movements. Occupational accidents have occurred during movement at different working levels, during the use of access and exit systems, and during the mounting of vehicles. Aging can also affect accident risk and body laterality. For example, falling accidents on stairs are common among the elderly. One reason for accidents may be that the structure of the access system or stair system is unsuitable for individual moving patterns depending partly on body laterality. Footedness and the way the feet are used may be contradictory to the demands of the moving situation, especially during uncommon or rapid situations. This contradiction may trigger disturbance during moving. The aims of this pilot study were (a) to review the literature briefly and (b) to describe the use of the dominant and nondominant foot by farmers and the elderly when mounting a tractor and stairs, respectively. The study also gives ideas for future studies based on both (a) and (b).     

AHP与GA-SVM耦合模型在滑坡预警中的应用*

为了减少滑坡造成的损失，提高滑坡预测的准确性，通过搭建灾害模拟平台获得滑坡的实验数据，在获得多组模拟实验数据后，分析各变量的特性。首先，通过层次分析(Analytic Hierarchy Process，AHP)算法，对滑坡进行危险度划分；然后，通过支持向量机(Support Vector Machine，SVM)建立模型，遗传算法(Genetic Algorithm,GA)再优化SVM参数，提出1种层次分析法与GA-SVM相耦合的模型。研究结果表明:AHP方法划分后的数据，通过GA与SVM结合建立的模型精度较好，实验预测结果与实际结果较为吻合，与单一SVM相比，精度更高，结果更好，更加适用于多变量的复杂非线性滑坡预警。     

一起有机过氧化物爆炸事故的调查和分析

阐述一起重大爆炸伤亡事故的现场调查和原因分析，介绍如何通过人证物证材料，用鱼刺图法找出可能引起事故的诸原因，逐项加以分析，将与人证或物证材料相矛盾的原因子以排除，最后剩下无法排除亦即能与人证物证相符的那个原因，就是事故的真正原因。笔者是这起事故调查专家组组长，取证和数据可靠。     

Debunking the false dichotomy of leadership idealism and pragmatism: Critical evaluation and support of newer genre leadership theories

Leadership theories have shifted over the last few decades from a focus on managerial functions and economic leader–follower exchanges toward greater focus on the interpersonal dynamics occurring within the leadership process. Theories such as transformational, ethical, authentic, and other “newer genre” theories were created to address neglected topics such as leader vision and inspirational messages, transparency, emotional effects, morality, individualized attention, and intellectual stimulation. Critiques of these theories, however, have been raised. In this paper, we address five of those critiques and argue for the validity and practical effectiveness of the new genre theories. Further, we describe how newer genre leadership research should be viewed as a performative epistemology, entailing a process of co‐creation involving scholars and practitioners. Finally, from this view, we provide general ideas for leader development. Copyright © 2014 John Wiley & Sons, Ltd.     

Occupational Safety and Health in Finland

In Finland, occupational safety is the responsibility of the employer, while the occupational safety and health laws are enforced by the Labour Inspection Service, an organization of the state. The Labour Inspection is divided in 11 administrative districts, and it employs 360 professionals. They are mandated to carry out site visits without prearranged appointments to inspect safe work situations, working hours, construction safety, or any aspect of accident risks. The inspectors are also mandated to verify the existence of sufficient occupational health services as prescribed by the Occupational Health Services Act for all employees. The occupational health services are typically provided by enterprise-owned medical departments, by mutually owned health care centers, by private practitioners, or by municipal health care centers. The latter are required by law to provide all services as prescribed by the legislation to anyone who comes to the facility. This situation is prevalent in the countryside, where there are very few private caregiving centers. Declaring occupational accidents and disease cases is mandatory, and the Inspection districts examine all accidents to establish causes and consequences, and to initiate prosecution in case of criminal negligence. Labour Inspection Districts are also notified of the new occupational disease cases as they are declared to insurance companies. Insurance for occupational disease, accidents, and death is an obligation of the employer, although they can choose the insurance company. The medical confidentiality between the workers and their occupational health care providers is very strict. Official statistics are maintained by the state Statistics Finland organization, and they may be used, for example, for research purposes by scientific institutes like the Finnish Institute of Occupational Health. Construction industry accounts for 25% of all fatal accidents (120 cases per 1 million working hours), followed by mechanical, wood, metal, machinery, and pulp and paper industry (10% each of fatal accidents) with rates ranging from 100–160 cases per 1 million working hours. There are some 5,000 occupational disease cases per year (rate 22/10,000 employed). The major disease categories include repetitive strain injuries (1,300 cases), respiratory allergies (600 cases), occupational skin diseases (1,000 cases), and 900 cases of noise-caused hearing loss. In 1998, 589 cases of asbestos-related diseases were reported.